Dell 1800MP Projector 取扱説明書

www.dell.com | support.dell.com

Dell™ 1800MP Projector

Owner’s Manual

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you

make better use of your projector.

NOTICE: A NOTICE indicates either potential damage to

hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property

damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell

Inc. is strictly forbidden.

Trademarks used in this text: Dell , the DELL logo, Dimension OptiPlex Dell

Precision Latitude Inspiron DellNet PowerApp PowerEdge PowerConnect

PowerVault are trademarks of Dell Inc.; DLP and Texas Instruments

trademarks of Texas Instruments Corporation; Microsoft Windows

registered trademarks of Microsoft Corporation; Macintosh

trademark of Apple Computer, Inc.

Other trademarks and trade names may be used in this document to refer to either

the entities claiming the marks and names or their products. Dell Inc. disclaims

any proprietary interest in trademarks and trade names other than its own.

Restrictions and Disclaimers

The information contained in this document, including all instructions, cau-

tions, and regulatory approvals and certifications, is based upon statements

provided to Dell by the manufacturer and has not been independently verified

or tested by Dell. Dell disclaims all liability in connection with any deficien-

cies in such information.

All statements or claims regarding the properties, capabilities, speeds, or

qualifications of the part referenced in this document are made by the

manufacturer and not by Dell. Dell specifically disclaims any knowledge of the

accuracy, completeness, or substantiation for any such statements.

Model 1800MP

September 2006 Rev. A00

Contents 3

Contents

1 Your Dell Projector . . . . . . . . . . . . . . . . . . 5

About Your Projector . . . . . . . . . . . . . . . . . 6

2 Connecting Your Projector . . . . . . . . . . . . 7

Connecting to a Computer . . . . . . . . . . . . . . . . . 8

Connecting to a DVD Player

. . . . . . . . . . . . . . . . 9

Connecting a DVD Player with an S-video Cable

. . . 9

Connecting a DVD Player with a Composite Cable

. 10

Connecting a DVD Player with a Component Cable

11

Professional Installation Options: . . . . . . . . . . 12

3 Using Your Projector . . . . . . . . . . . . . . . . 13

Turning Your Projector On . . . . . . . . . . . . . . . . 13

Turning Your Projector Off

. . . . . . . . . . . . . . . . 13

Adjusting the Projected Image

. . . . . . . . . . . . . 14

Raising the Projector Height

. . . . . . . . . . . . 14

Lowering the Projector Height

. . . . . . . . . . . 14

Adjusting the Projector Zoom and Focus

. . . . . . . . 15

Adjusting Projection Image Size . . . . . . . . . . . . 16

Using the Control Panel

. . . . . . . . . . . . . . . . . 17

4 Contents

Using the Remote Control . . . . . . . . . . . . . . . . 19

Using the On-Screen Display

. . . . . . . . . . . . . . 20

Main Menu

. . . . . . . . . . . . . . . . . . . . . 21

Input Select

. . . . . . . . . . . . . . . . . . . . . 21

Auto-Adjust

. . . . . . . . . . . . . . . . . . . . . 21

Set Up . . . . . . . . . . . . . . . . . . . . . . . . 22

PICTURE (in PC Mode)

. . . . . . . . . . . . . . . 23

PICTURE (in Video Mode)

. . . . . . . . . . . . . 23

DISPLAY (in PC Mode) . . . . . . . . . . . . . . . 24

DISPLAY (in Video Mode)

. . . . . . . . . . . . . 25

LAMP

. . . . . . . . . . . . . . . . . . . . . . . . 25

LANGUAGE . . . . . . . . . . . . . . . . . . . . . 26

Preferences

. . . . . . . . . . . . . . . . . . . . 27

4 Troubleshooting Your Projector . . . . . . . 31

Changing the Lamp . . . . . . . . . . . . . . . . . . . 35

5 Specifications . . . . . . . . . . . . . . . . . . . . . 37

Contacting Dell . . . . . . . . . . . . . . . . . . . . 43

Appendix: Regulatory Notices . . . . . . . . . 71

FCC Notices (U.S. Only) . . . . . . . . . . . . . . . 71

NOM Information (Mexico Only)

. . . . . . . . . . 72

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Your Dell Projector 5

1

Your Dell Projector

Your projector comes with all the items shown below. Ensure that you have all the

items, and contact Dell if anything is missing.

Package Contents

1.8m power cord (3.0m in Americas) 1.8m VGA cable (VGA to VGA)

Batteries (2) Remote control

Documentation Carrying case

6 Your Dell Projector

About Your Projector

1 Remote control receiver

2 Elevator button

3 Lens

4 Focus ring

5 Zoom tab

6 Power cord connector

Connecting Your Projector 7

2

Connecting Your Projector

Monitor loop through from VGA-A In to VGA-A Out only.

1 Audio output connector

2 Audio input connector

3 VGA-B In connector

4 VGA-A In connector

5 S-video connector

6 Video input connector

7 VGA-A out connector

8 USB remote connector

9 RS232 connector

10 Kensington lock hole

8 Connecting Your Projector

Connecting to a Computer

The USB cable is not provided by Dell.

Consult a professional installer for the cable.

1 Power cord

2 VGA to VGA cable

3 USB cable

Connecting Your Projector 9

Connecting to a DVD Player

Connecting a DVD Player with an S-video Cable

The S-video cable is not provided by Dell.

Consult a professional installer for the cable.

1 Power cord

2 S-video cable

10 Connecting Your Projector

Connecting a DVD Player with a Composite Cable

The Composite cable is not provided by Dell.

Consult a professional installer for the cable.

1 Power cord

2 Composite video cable

Connecting Your Projector 11

Connecting a DVD Player with a Component Cable

The VGA to YPbPr cable is not provided by Dell.

Consult a professional installer for the cable.

1Power cord

2 VGA to YPbPr cable

12 Connecting Your Projector

Professional Installation Options:

Connecting a Computer with a RS232 Cable

The RS232 cable is not provided by Dell.

Consult a professional installer for the cable.

1Power cord

2 RS232 cable

Using Your Projector 13

3

Using Your Projector

Turning Your Projector On

NOTE: Turn on the projector before you turn on the source. The power button

light blinks blue until pressed.

1

Remove the lens cap.

2

Connect the power cord and appropriate signal cables. For information about

connecting the projector, see "Connecting Your Projector" on page 7.

3

Press the power button (see "Using the Control Panel" on page 17 to locate the

power button). The Dell logo displays for 30 seconds.

4

Turn on your source (computer, DVD player, etc.). The projector automatically

detects your source.

If the "Searching for signal..." message appears on the screen, ensure

that the appropriate cables are securely connected.

If you have multiple sources connected to the projector, press the Source button

on the remote control or control panel to select the desired source.

Turning Your Projector Off

NOTICE: Unplug the projector after properly shutting down as explained in the

following procedure.

1

Press the power button.

2

Press the power button again. The cooling fans continue to operate for 60 seconds.

3

Disconnect the power cord from the electrical outlet and the projector.

NOTE: If you press the power button while the projector is running, the "Power

Off the Lamp?" message appears on the screen. To clear the message, press any

button on the control panel or ignore the message; the message disappears after 3

seconds.

14 Using Your Projector

Adjusting the Projected Image

RAISING THE PROJECTOR HEIGHT

1

Press the elevator button.

2

Raise the projector to the desired display angle, and then release the button to

lock the elevator foot into position.

3

Use the tilt adjustment wheel to fine-tune the display angle.

LOWERING THE PROJECTOR HEIGHT

1

Press the elevator button.

2

Lower the projector, and then release the button to lock the elevator foot into

position.

1 Elevator button

2 Elevator foot

3 Tilt adjustment wheel

Using Your Projector 15

Adjusting the Projector Zoom and Focus

CAUTION: To avoid damaging the projector, ensure that the zoom lens and

elevator foot are fully retracted before moving the projector or placing the

projector in its carrying case.

1

Rotate the zoom tab to zoom in and out.

2

Rotate the focus ring until the image is clear. The projector focuses at distances

from 4.9 ft to 39.4 ft (1.5 m to 12.0 m).

1 Zoom tab

2 Focus ring

16 Using Your Projector

Adjusting Projection Image Size

Using Your Projector 17

Using the Control Panel

Screen

(Diagonal)

Max. 38.1"

(96.8cm)

86.4"

(219.4cm)

139.8"

(355.0cm)

195.7"

(497.0cm)

249.0"

(632.5cm)

304.9"

(774.5cm)

Min. 34.7"

(88.0cm)

78.5"

(199.5cm)

127.1"

(322.7cm)

177.9"

(451.8cm)

226.4"

(575.0cm)

277.2"

(704.1cm)

Screen Size

Max.

(WxH)

30.5"X22.9" 69.1"X51.8" 111.8"X83.9" 156.5"X117.4" 199.2"X149.4" 243.9"X183.0"

(77.5cm X

58.1cm)

(175.6cm X

131.7cm)

(284.0cm X

213.0cm)

(397.6cm X

298.2cm)

(506.0cm X

379.5cm)

(619.6cm X

464.7cm)

Min.

(WxH)

27.7" X

20.8"

62.8" X

47.1"

101.6" X

76.2"

142.3" X

106.7"

181.1" X

135.8"

221.8" X

166.3"

(70.4cm X

52.8cm)

(159.6cm X

119.7cm)

(258.2cm X

193.6cm)

(361.4cm X

271.1cm)

(460.0cm X

345.0cm)

(563.3cm X

422.5cm)

Distance 4.9' (1.5m) 11.2' (3.4m) 18.0' (5.5m) 25.3' (7.7m) 32.2' (9.8m) 39.4' (12.0m)

* This graph is for user reference only.

1 Power Turn the projector on and off. For more

information, see "Turning Your Projector On" on

page 13 and "Turning Your Projector Off" on

page 13.

1

3

5

2

6

9

8

11

4

7

10

18 Using Your Projector

2 TEMP warning light

• A solid orange TEMP light indicates that the

projector has overheated. The display

automatically shuts down. Turn the display on

again after the projector cools down. If the

problem persists, contact Dell.

• A blinking orange TEMP light indicates that a

projector fan has failed and the projector

automatically shuts down. If the problem

persists, contact Dell.

3 Source Press to toggle through Analog RGB, Composite,

Component-i, S-video, and Analog YPbPr sources

when multiple sources are connected to the

projector.

4 Keystone adjustment Press to adjust image distortion caused by tilting

the projector. (±15 degrees)

5 Resync Press to synchronize the projector to the input

source. Resync does not operate if the on-screen

display (OSD) is displayed.

6 Menu Press to activate the OSD. Use the directional

keys and Menu button to navigate through the

OSD.

7 and buttons Press to adjust the OSD setting.

8 Enter Press to confirm the selection item.

9 Keystone adjustment Press to adjust image distortion caused by tilting

the projector. (±15 degrees)

10 Up and Down Press to select the OSD items.

11 LAMP warning light If the LAMP light is solid orange, replace the

lamp. If the LAMP light is blinking orange, the

system has failed and the projector will

automatically shut down. If this problem persists,

contact Dell.

Using Your Projector 19

Using the Remote Control

1 Power Turn the projector on and off. For more

information, see "Turning Your Projector On" on

page 13 and "Turning Your Projector Off" on

page 13.

2 Press to adjust the OSD setting.

3 Down button Press to select OSD items.

4 Mute Press to mute or unmute the projector speaker.

5 Volume Press to increase the volume.

6 Page Press to move to previous page.

7 Page Press to move to next page.

1

2

3

4

5

6

7

8

9

19

18

17

16

15

14

13

11

10

12

20 Using Your Projector

Using the On-Screen Display

The projector has a multi-language On-Screen Display (OSD) that can be

displayed with or without an input source present.

In the Main Menu, press or to navigate through the tabs.

In the submenu, press or to make a selection. When an item is selected, the

color changes to dark gray. Use or on the control panel or the remote

control to make adjustments to a setting.

8 Video mode The Dell 1800MP Micro-projector has preset

configurations that are optimized for displaying

data (PC Graphics) or video (movies, games,

etc.). Press Video Mode button to toggle between

PC mode, Movie mode, Game Mode, sRGB, or

CUSTOM mode (for user to setup and save

preferred settings). Pressing the Video Mode

button once will show the current display mode.

Pressing the Video Mode button again will switch

between modes.

9 Blank screen Press to hide the image, press again to resume

display of the image.

10 LED light LED indicator.

11 Up button Press to select OSD items.

12 Enter button Press to confirm the selection.

13 Press to adjust the OSD setting.

14 Menu Press to activate the OSD.

15 Volume Press to decrease the volume.

16 Keystone adjustment Press to adjust image distortion caused by tilting

the projector. (±15 degrees)

17 Source Press to switch between Analog RGB, Digital

RGB, Composite, Component-i, S-video, and

Analog YPbPr sources.

18 Auto adjust Press to synchronize the projector to the input

source. Auto adjust does not operate if the OSD

(On-Screen Display) is displayed.

19 Keystone adjustment Press to adjust image distortion caused by tilting

the projector. (±15 degrees)

ページを読み込んでいます...

Dell 1800MP Projector 取扱説明書

関連論文