Simplicity 613477-0283-J1 ユーザーマニュアル

ブランド: Simplicity

モデル: 613477-0283-J1

カテゴリー: 自動車アクセサリー

タイプ: ユーザーマニュアル

Operator's Manual

Panduan Operator

操作マニュアル

작동차 설명서

Manual Operator

คู่มือการใช้งาน

Sổ tay Vận hành

操作员手冊

Models:54E000,540000,61E000,610000,61G200, 61G300

Revision A

Not for

Reproduction

2 vanguardpower.com

Not for

Reproduction

Not for

Reproduction

General Information

This manual contains safety information so that you will know the hazards and risks

related to this engine and how to prevent them. It also contains instructions for the

correct use and maintenance of the engine. Because Briggs & Stratton does not know

what equipment this engine will power, it is important that you read, understand, and

obey these instructions. Save these original instructions for future reference.

NOTE:The figures and illustrations in this manual are for reference only and can be

different from your model. If you need help, contact an Authorized Service Dealer.

For replacement parts or technical help, record the date of purchase, engine model,

type, trim, and the engine serial number. These numbers are located on your engine.

Refer to the Features and Controls section.

Date of Purchase

Engine Model - Type - Trim

Engine Serial Number

European Office Contact Information

For questions related to European emissions, contact our European office at:

Max-Born-Straße 2, 68519 Viernheim, Germany.

European Union (EU) Stage V (5): Carbon

Dioxide (CO2) Values

Enter CO2 in the search window on BriggsandStratton.com to find carbon dioxide values

of Briggs & Stratton EU Type-Approval Certificate engines.

Recycling Information

Recycle all cartons, boxes, used oil, and batteries as

specified by government regulations.

Operator Safety

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information about hazards that could

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used to

indicate the likelihood and the potential severity of injury. In addition, a hazard symbol

is used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious

injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or moderate

injury.

NOTICE indicates information considered important but not hazard-related.

Hazard Symbols and Meanings

Safety information about

hazards that can result in

personal injury.

Read and understand the

Operator's Manual before

operating or servicing the

unit.

Fire Hazard Explosion Hazard

Shock Hazard Toxic Fume Hazard

Hot Surface Hazard Noise Hazard - Ear

protection recommended

for extended use.

Thrown Object Hazard -

Wear eye protection.

Explosion Hazard

Frostbite Hazard Kickback Hazard

Amputation Hazard -

Moving Parts

Chemical Hazard

Thermal Heat Hazard Corrosive Hazard

Safety Messages

WARNING

Briggs & Stratton® Engines are not designed for and are not to be used to power:

fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);

motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not

sanctioned by Briggs & Stratton. For information about competitive racing products, see

www.briggsracing.com. For use with utility and side-by-side ATVs, please contact Briggs

& Stratton Power Application Center, 1-866-927-3349. Incorrect engine use could result

in serious injury or death.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)

minutes to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above

the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are

correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN

position. Move the throttle (if equipped) to the FAST position and crank until the

engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

When you operate the equipment

• Do not tilt the engine or the equipment at an angle which causes fuel to spill.

• Do not choke the carburetor (if equipped) to stop the engine.

• Do not start or operate the engine with the air cleaner (if equipped) or the air

filter (if equipped) removed.

When you do maintenance

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occurand could result a fire or an explosion.

• During maintenance if it is necessary to tilt the unit, make sure that the fuel tank,

if mounted on the engine, is empty and that the spark plug side is up. If the fuel

tank is not empty, leakage can occurand could result a fire or an explosion.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• Do not change the governor spring, links or other parts to increase engine

speed.

• Do not hit the flywheel with a hammer or hard object. This could result in failure

of the flywheel during operation.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts could result in damage or an injury.

4 vanguardpower.com

Not for

Reproduction

When you move the location of equipment

• Make sure that the fuel tank is EMPTY or that the fuel shut-off valve is in the

CLOSED position.

When fuel or equipment is in storage with fuel in the fuel tank

• Because pilot lights or other ignition sources can cause explosions, keep fuel or

equipment away from furnaces, stoves, water heaters or other appliances that

have pilot lights.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

Engine start-up causes spark that could result in a fire or explosion.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See

a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of

carbon monoxide gas, ONLY operate this product outdoors and far away from

windows, doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide

alarms with battery back-up as specified by the manufacturer's instructions.

Smoke alarms cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces,

sheds, or other closed spaces, even if you use fans or open doors and windows

for ventilation. After the operation of this product, carbon monoxide can quickly

collect in these spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

WARNING

Fast retraction of the starter cord (kickback) will pull your hand and arm to the

engine faster than you can let go.Broken bones, fractures, bruises or sprains

could result.

• To prevent kickback when you start the engine, pull the starter cord slowly until

resistance is felt and then pull quickly.

• Before you start the engine, disconnect or remove all external equipment and

engine loads.

• Make sure that direct-coupled equipment components, such as, but not limited

to, blades, impellers, pulleys, and sprockets, are correctly attached.

WARNING

Rotating parts can entangle hands, feet, hair, clothing, or accessories and result

in traumatic amputation or laceration.

• Operate equipment with the guards correctly installed.

• Keep hands and feet away from rotating parts.

• Remove jewelry and make sure that long hair is away from all rotating parts.

• Do not wear loose clothes or items that could become caught.

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

WARNING

Accidental engine spark can cause an electric shock or fire and could result in

entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start.)

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

If you smell gas

• Do not start the engine.

• Do not switch on electrical switches.

• Do not use a phone in the vicinity.

• Evacuate the area.

• Contact the gas supplier or the fire department.

Features and Controls

Engine Controls

Compare the callout letters in Figures 1, 2, 3, and 4 to the engine controls in the list that

follows:

A. Engine Identification Numbers Model - Type - Code

B. Spark Plug

C. Cyclonic Air Cleaner

D. Low Profile Air Cleaner

E. Dipstick

F. Oil Fill

G. Oil Filter

H. Oil Drain Plug

I. Oil Pressure Sensor

J. Finger Guard

K. Electric Starter

L. Starter Solenoid

M. Regulator / Rectifier

N. Carburetor - Carburetor Models

O. Oil Cooler (if equipped)

P. Muffler (if equipped)

Q. Fuel Pump

Starter Switch

Throttle Control

ChokeControl(Carburetor Models

)

U. Fuel Filter

V. Tachometer (if equipped)

Some engines and equipment have remote controls. See the equipment manual for the

location and operation of remote controls.

Engine Control Symbols and Meanings

Engine Speed - FAST Engine Speed - SLOW

Engine Speed - STOP ON - OFF

Not for

Reproduction

Engine Start

Choke CLOSED

Engine Start

Choke OPEN

Fuel Cap

Fuel Shut-off OPEN

Fuel Shut-off CLOSED

Fuel Level - Maximum

Do Not Overfill

Operation

Oil Recommendations

Oil Capacity: See the Specifications section.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

We recommend the use of Briggs & Stratton

Warranty Certified oils for best

performance. Other high-quality detergent oils are permitted if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Use the chart to select the best viscosity for the outdoor temperature range expected.

Engines on most outdoor power equipment operate well with 5W-30 Synthetic oil. For

equipment operated in hot temperatures, Vanguard

15W-50 Synthetic oil gives the best

protection.

A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.

B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil

consumption. Checkthe oil level frequently.

C 5W-30

D Synthetic 5W-30

Vanguard

Synthetic 15W-50

Check and Add Oil

Before you check or add oil

• Make sure the engine is level.

• Clean the oil fill area of debris.

• Refer to the Specifications section for oil capacity.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

1. Remove the dipstick (A, Figure 5) and clean with a cloth.

2. Install and tighten the dipstick (A, Figure 5).

3. Remove the dipstick and check the oil level. Make sure that the oil level is at the

top of the full indicator (B, Figure 5) on the dipstick.

4. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 5). Do not add

too much oil. After you add oil, wait one minute and check the oil level again. Make

sure that the oil level is correct.

5. Install and tighten the dipstick (A, Figure 5).

Low Oil Protection System (if equipped)

A low oil sensor is installed on some engines. If the oil is low, the sensor will display a

warning light or stop the engine. Stop the engine and follow these steps before you start

the engine.

• Make sure the engine is level.

• Do an oil check. Refer to the Check Oil Level section.

• If the oil level is low, add the correct amount of oil. Start the engine and make

sure the warning light (if equipped) does not come on.

• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton

Authorized Service Dealer to have the oil problem corrected.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is permitted.

NOTICE

Do not use unapproved gasoline, such as E15 and E85. Do not mix oil in gasoline or

change the engine to operate on alternate fuels. Use of unapproved fuels could result in

damage to engine components, which will not be repaired under the warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. Refer

to the Storage section. All fuel is not the same. If start or performance problems occur,

change fuel providers or brands. This engine is certified to operate on gasoline. The

emissions control system for carbureted engines is EM (Engine Modifications). The

emissions control systems for engines with electronic fuel injection are ECM (Engine

Control Module), MPI (Multi Port Injection), and if equipped an O2S (Oxygen Sensor).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is permitted.

For carbureted engines, high altitude adjustment is required to maintain performance.

Operation without this adjustment will cause decreased performance, increased fuel

consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service

Dealer for high altitude adjustment information. Operation of the engine at altitudes

below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.

Add Fuel

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)

minutes to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above

the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.

2. Fill the fuel tank (A, Figure 6) with fuel. Because fuel will expand, do not fill above

the bottom of the fuel tank neck (B).

3. Install the fuel cap.

Start and Stop Engine

Start Engine

WARNING

Fast retraction of the starter cord (kickback) will pull your hand and arm to the

engine faster than you can let go.Broken bones, fractures, bruises or sprains

could result.

• To prevent kickback when you start the engine, pull the starter cord slowly until

resistance is felt and then pull quickly.

• Before you start the engine, disconnect or remove all external equipment and

engine loads.

• Make sure that direct-coupled equipment components, such as, but not limited

to, blades, impellers, pulleys, and sprockets, are correctly attached.

6 vanguardpower.com

Not for

Reproduction

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result

in burns or death.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped)

are correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN

position. Move the throttle (if equipped) to the FAST position and crank until the

engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY.

See a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of

carbon monoxide gas, ONLY operate this product outdoors and far away from

windows, doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide

alarms with battery back-up as specified by the manufacturer's instructions.

Smoke alarms cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces,

sheds, or other closed spaces, even if you use fans or open doors and

windows for ventilation. After the operation of this product, carbon monoxide

can quickly collect in these spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers

or dealers could have added oil to the engine. Before you start the engine for the

first time, make sure that the oil is at the correct level. Add oil as specified by the

instructions in this manual. If you start the engine without oil, damage will occur and the

engine will not be repaired under warranty.

Types of Starting Systems

Before you start the engine, you must know the type of starting system on your engine.

Your engine will have one of these types.

• Electronic Fuel Injection (EFI) System: An EFI system does not have a

choke or a primer.

• Choke System: This type of system has a choke to be used in cool

temperatures. Some models will have a separate choke control while others

will have a combination choke and throttle choke. It does not have a primer.

NOTE:Your equipment could have remote controls. Refer to the equipment manual for

location and operation of remote controls.

Electronic Fuel Injection (EFI) System

1. Check the engine oil. See the Check Oil Level section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.

4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate

the engine in the FAST position.

5. Turn the electric start switch (D, Figure 7) to the ON or START position.

NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).

Wait one minute between start cycles.

If the engine does not start after 3or 4 times, contact your local dealer or goto

vanguardpower.com or call 1-800-999-9333.

Choke System

1. Check the engine oil. See the Check Oil Level section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.

4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate

the engine in the FAST position.

5. Move the choke control (C, Figure 7), or the combination choke and throttle (B,C) to

the CLOSED position.

NOTE:To start the engine with a dry fuel system, additional cranking time in the choke

position will be required. This will give the fuel pump time to prime the fuel system.

6. Turn the key switch (D, Figure 7) to the ON or START position.

7. If the engine starts but will not continue to operate, move the choke control (C,

Figure 7) to the OPEN position to start the engine.

NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).

Wait one minute between start cycles.

8. As the engine warms, move the choke control (C, Figure 7) to the OPEN position.

If the engine does not start after 3or 4 times, contact your local dealer or goto

vanguardpower.com or call 1-800-999-9333.

Stop the Engine

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

• Do not choke the carburetor (if equipped) to stop the engine.

1. With the throttle control in the SLOW position, turn the electric start switch (D,

Figure 7) to the OFF position. Remove the key and keep it in a safe place out of the

reach of children.

2. After the engine stops, move the fuel shut-off (A, Figure 7), if equipped, to the

CLOSED position.

Maintenance

Maintenance Information

WARNING

During maintenance if it is necessary to tilt the unit, make sure that the fuel tank, if

mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not

empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted

in a different direction, it will not easily start because of oil or fuel contamination of the air

filter or the spark plug.

We recommend that you see a Briggs & Stratton Authorized Service Dealer for all

maintenance and servicing of the engine and engine parts.

NOTICE

All the components used to build this engine must remain in place for correct operation.

WARNING

Accidental engine spark can cause an electric shock or fire and could result in

entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start.)

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

Emissions Control Service

For maintenance, replacement, or repair of emissions control devices and

systems, contact a qualified off-road engine repair establishment or service

technician. However, for "no charge" emissions control service, the work must be done

by a factory authorized dealer. Refer to the Emissions Control Statements.

Maintenance Schedule

Intervals of 8 Hours or Daily

• Check the engine oil level.

• Clean the area around the muffler and controls.

Intervals of 100 Hours or Annually

Not for

Reproduction

•

Clean or replace the air filter

1 2

• Change the engine oil and filter.

• Replace the oil filter (if equipped).

• Replace the spark plugs.

• Check the muffler and spark arrester.

• Service the exhaust system.

Intervals of 250 Hours or Annually

• Check the valve clearance. Adjust if necessary.

Intervals of 400 Hours or Annually

•

Change the air filter

• Replace the fuel filter.

•

Service the air cooling system

•

Clean the oil cooler fins

Intervals of 600 Hours

• Replace the safety filter, if equipped.

In dusty conditions or when airborne debris is present, clean more frequently.

Every third air filter change, replace the inner safety filter (if equipped.

Electronic Fuel Injection (EFI) System

The EFI System monitors engine temperature, engine speed, and battery voltage for

engine start-up and warm-up. There are no adjustments on the system. If start-up or

operation problems occur, contact a Briggs & Stratton Authorized Service Dealer.

NOTICEMake sure to obey the steps that follow or damage to the EFI system could

occur.

• DO NOT start the engine if the battery cables are loose.

• Turn the key to the OFF position before you disconnect, remove, and / or install

the battery.

• DO NOT use a battery charger to start the engine.

• DO NOT disconnect the battery cables during engine operation.

• When you disconnect the battery cables, first connect the positive (+) cable, and

then connect the negative (-) cable to the battery.

• When you charge the battery, turn the ignition switch to the OFF position,and

disconnect the negative (-) battery cable from the battery.

• DO NOT spray water directly on the Electronic Control Module.

Carburetor and Engine Speed

Do not make adjustments to the carburetor or engine speed. The carburetor was set at

the factory to operate satisfactorily under most conditions. Do not change the governor

spring, linkages, or other parts to adjust the engine speed. If any adjustments are

required contact a Briggs & Stratton Authorized Service Dealer for service.

NOTICE

The equipment manufacturer specifies the maximum speed for the engine as installed

on the equipment. Do not exceed this speed. If you are not sure what the equipment

maximum speed is, or what the engine speed is set to from the factory, contact a Briggs

& Stratton Authorized Service Dealer for assistance. For safe and correct operation

of the equipment, the engine speed should only be adjusted by a qualified service

technician.

Servicing the Spark Plug

Check the spark plug gap (A, Figure 8) with a wire gauge (B). If necessary, set the

spark plug gap. Install and tighten the spark plug to the correct torque. For gap or torque

specifications, refer to the Specifications section.

NOTE:In some areas, it is mandatory by local law that you use a resistor spark plug

to decrease ignition signals.If a resistor spark plug was installed by the equipment

manufacturer, use the same type for replacement.

Servicing theExhaust System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Remove debris from the muffler and cylinder area. Examine the muffler for cracks,

corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and

examine for damage or carbon blockage. If damage is found, install the replacement

parts before you operate the equipment.

WARNING

Replacement parts must be of the same design and installed in the same position as the

original parts. Other parts could result in damage or an injury.

Change Engine Oil

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occur and cause a fire or an explosion.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

Used oil is a hazardous waste product and must be discarded of correctly. Do not

discard with household waste. Contact your local authorities, service center, or dealer

for safe disposal or recycling facilities.

Remove Oil

1. With engine OFF but warm, disconnect the spark plug wire(s)(D, Figure 9), and

keep it away from the spark plug(s)(E).

2. Remove the dipstick (A, Figure 10).

3. Remove the oil drain plug (F, Figure 11). Drain the oil into an approved container.

4. Install and tighten the oil drain plug(F, Figure 11).

Change Oil Filter, if equipped

1. Drain the oil from the engine. Refer to the Remove Oil section.

2. Remove the oil filter (H, Figure 12) anddiscard correctly.

3. Before you install the new oil filter, lightly lubricate the oil filter gasket withclean oil.

4. Install the oil filter by hand until the gaskettouchesthe oil filter adapter, then tighten

the oil filter 1/2 to 3/4 turns.

5. Add oil. Refer to the Add Oil section.

6. Start and operatethe engine. When the engine is warm, do a checkfor oil leaks.

7. Stop the engine. Make sure thatoil level is at the top of the full indicator (B, Figure

5) on the dipstick.

Add Oil

• Make sure the engine is level.

• Clean the oil fill area of all debris.

• Refer to the Specifications section for oil capacity.

1. Remove the dipstick (A, Figure 10). Remove oil from the dipstick with a clean cloth.

2. Slowly add oil into the engine oil fill (C, Figure 10). Do not overfill. Wait one

minute and then check the oil level.

3. Install and tighten the dipstick (A, Figure 10).

4. Remove the dipstick and check the oil level. The correct oil level is at the top of the

full indicator (B, Figure 10) on the dipstick.

5. Install and tighten the dipstick (A, Figure 10).

6. Connect the spark plug wire(s) (D, Figure 9) to the spark plug(s) (E).

Servicing the Air Filter

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

• Do notstart and operate the engine with the air cleaner assembly (if equipped)

or the air filter (if equipped) removed.

8 vanguardpower.com

Not for

Reproduction

NOTICE

Do not use pressurized air or solvents to clean the filter. Pressurized air could result in

damage to the filter and solvents will dissolve the filter.

See the Maintenance Schedule for service requirements.

Different models will use a foam or a paper filter. Some models could also have an

optional pre-cleaner that can be washed and used again. Compare the illustrations in

this manual with the type installed on your engine and service as follows.

Cyclonic Air Filter

1. Open the fastener(s) (A, Figure 13) and remove the cover (B).

2. Remove the air filter (C, Figure 13).

3. To loosen debris, lightly tap the air filter on a hard surface. If the air filter is dirty,

replace it with a new air filter.

4. To remove the safety filter (D, Figure 13), if equipped, carefully pull it away from the

air cleaner body (E). Make sure that dirt or debris does not go into the engine.

5. Install the new safety filter (D, Figure 13) in the air cleaner body (E).

6. Install the air filter (C, Figure 13) above the safety filter (D).

7. Install the cover (B, Figure 13) and close the fastener(s) (A).

Low Profile Air Filter

1. Remove the fastener(s) (A, Figure 14).

2. Remove the cover (B, Figure 14).

3. Remove the fastener(s) (C, Figure 14) and retainer (D).

4. Remove the air filter (E, Figure 14).

5. Remove the pre-cleaner (F, Figure 14), if equipped, from the air filter (E).

6. To loosen debris, lightly tap the air filter (E, Figure 14) on a hard surface. If the air

filter is dirty, replace with a new air filter.

7. Clean the pre-cleaner (F, Figure 14), if equipped, in liquid detergent and water.

Make sure the pre-cleaner is fully dry. Do not lubricate the pre-cleaner.

8. Assemble the dry pre-cleaner (F, Figure 14), if equipped, to the air filter (E).

9. Install the air filter (E, Figure 14) with the retainer (D) and fastener(s) (C).

10. Install the cover (B, Figure 14) with the fastener(s) (A). Make sure the fastener(s) is

tight.

Servicing the Cooling System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible debris, such as leaves, grass, and brush can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

NOTICE

Do not use water to clean the engine. Water could cause contamination of the fuel

system. Use a brush or dry cloth to clean the engine.

This is an air cooled engine. Dirt or debris can stop the air flow and cause the engine to

become too hot and result in unsatisfactory performance and decreased engine life.

1. Use a brush or dry cloth to remove debris from the air intake area (A, Figure 15).

2. Keep linkage, springs, and controls (B, Figures 15, 16) clean.

3. Keep the area around and behind the muffler (C, Figures 15, 16) free of

combustible debris.

4. Make sure the oil cooler fins (D, Figure 15) are free of dirt and debris.

5. Loosen the fastener(s) (E, Figures 15, 16) and remove the debris access panels

(F). Remove grass and debris that has collected on the cylinders.

6. Install the debris access panels (F, Figures 15, 16) and attach with fastener(s) (E).

After a period of time, debris can collect in the cylinder cooling fins and cause the engine

to overheat. This debris cannot be removed without partial disassembly of the engine.

As recommended in the Maintenance Schedule, have a Briggs & Stratton Authorized

Service Dealer inspect and clean the air cooling system.

Servicing the Fuel System

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• Before you clean or replace the fuel filter, drain the fuel tank or close the fuel

shut-off valve.

• If fuel spills, wait until it dries before you start the engine.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts could result in damage or an injury.

Fuel Filter, if equipped

1. Before you clean or replace the fuel filter (A, Figure 17), drain the fuel tank or close

the fuel shut-off valve. If the fuel tank is not drained, fuel leakage could occur and

cause a fire or explosion.

2. Use pliers to squeeze tabs (B, Figure 17) on the clamps (C), then move the clamps

away from the fuel filter (A). Twist and pull the fuel lines (D) off of the fuel filter.

3. Check the fuel lines (D, Figure 17) for cracks or leaks. Replace if necessary.

4. Replace the fuel filter (A, Figure 17) with an original equipment replacement filter.

5. Attach the fuel lines (D, Figure 17) with clamps (C).

Storage

Fuel System

Refer to Figure: 18.

Keep the engine level (normal operating position). Fill the fuel tank (A, Figure 18) with

fuel. For fuel expansion, do not fill above the fuel tank neck (B).

Fuel can become stale when kept in a storage container for more than 30 days. Each

time you fill the container with fuel, addfuel stabilizerto the fuel as specified by the

manufacturer’s instructions. This keeps fuel fresh and decreases fuel-related problems

or contamination in the fuel system.

It is not necessary to drain fuel from the engine whenfuel stabilizeris added as

instructed. Before storage, turn the engine ON for 2 minutes to move the fuel and

stabilizer through the fuel system.

If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained

into an approved container. Operate the engine until it stops from lack of fuel. The use of

a fuel stabilizer in the storage container is recommended to keep fuel fresh.

Engine Oil

While the engine is still warm, change the engine oil. Refer to Change the Engine Oil

section.

Troubleshooting

Assistance

For assistance, contact your local dealer or go to vanguardpower.com or call

1-800-999-9333 (in USA).

Specifications

Specifications and Service Parts

Models: 540000 , 54E000

Displacement 54.68 ci (896 cc)

Bore 3.366 in ( 85,5 mm)

Stroke 3.071 in (78,0 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap .030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap .005 - .008 in (,13 - ,20 mm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Models: 610000, 61E000, 61G200, 61G300

Displacement 60.60 ci (993 cc)

Bore 3.366 in ( 85,5 mm)

Not for

Reproduction

Models: 610000, 61E000, 61G200, 61G300

Stroke 3.406 in (86,5 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap .030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap .005 - .008 in (,13 - ,20 mm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Service Parts - Models: 540000, 54E000,

610000, 61E000, 61G200, 61G300

Service Part Part Number

Cyclonic Air Filter (Figure 13) 841497

Cyclonic Safety Filter (Figure 13) 821136

Air Filter, Low Profile (Figure 14) 692519

Pre-cleaner, Low Profile (Figure 14) 692520

Oil - SAE 30 100028

Oil Filter 842921

Fuel Filter 691035

Resistor Spark Plug 491055

Long Life Platinum Spark Plug 5066

Spark Plug Wrench 19374

Spark Tester 19368

Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and

1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily

at an angle up to 15°. Refer to the equipment Operator's Manual for safe permitted

operating limits on slopes.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance

with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque

Rating Procedure, and is rated in accordance with SAE J1995. Torque values are

derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM

for all others; horsepower values are derived at 3600 RPM. The gross power curves

can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with

exhaust and air cleaner installed whereas gross power values are collected without

these attachments. Actual gross engine power will be higher than net engine power and

is affected by, among other things, ambient operating conditions and engine-to-engine

variability. Given the wide array of products on which engines are placed, the gasoline

engine may not develop the rated gross power when used in a given piece of power

equipment. This difference is due to a variety of factors including, but not limited to, the

variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel

pump, etc.), application limitations, ambient operating conditions (temperature, humidity,

altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,

Briggs & Stratton may substitute an engine of higher rated power for this engine.

Warranty

Briggs & Stratton Engine Warranty

Effective January 2019

Limited Warranty

Briggs & Stratton warrants that, during the warranty period specified below, it will repair

or replace, free of charge, any part that is defective in material or workmanship or

both. Transportation charges on product submitted for repair or replacement under this

warranty must be borne by purchaser. This warranty is effective for and is subject to

the time periods and conditions stated below. For warranty service, find the nearest

Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.

The purchaser must contact the Authorized Service Dealer, and then make the product

available to the Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of

merchantability and fitness for a particular purpose, are limited to the warranty

period listed below, or to the extent permitted by law. Liability for incidental or

consequential damages are excluded to the extent exclusion is permitted by law. Some

states or countries do not allow limitations on how long an implied warranty lasts,

and some states or countries do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation and exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which

vary from state to state and country to country

Standard Warranty Terms

1, 2, 3

Vanguard®; Commercial Series

Consumer Use - 36 months

Commercial Use - 36 months

XR Series

Consumer Use - 24 months

Commercial Use - 24 months

All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve

Consumer Use - 24 months

Commercial Use - 12 months

All Other Engines

Consumer Use - 24 months

Commercial Use - 3 months

These are our standard warranty terms, but occasionally there may be additional

warranty coverage that was not determined at time of publication. For a listing

of current warranty terms for your engine, go to BRIGGSandSTRATTON.com or

contact your Briggs & Stratton Authorized Service Dealer.

There is no warranty for engines on equipment used for prime power in place

of a utility; standby generators used for commercial purposes, utility vehicles

exceeding 25 MPH, or engines used in competitive racing or on commercial or

rental tracks.

Vanguard installed on standby generators: 24 months consumer use, no

warranty commercial use. Commercial Series with manufacturing date before July

2017: 24 months consumer use, 24 months commercial use.

In Australia - Our goods come with guarantees that cannot be excluded under

the Australian Consumer Law. You are entitled to a replacement or refund for a

major failure and for compensation for any other reasonably foreseeable loss or

damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure.

For warranty service, find the nearest Authorized Service Dealer in our dealer

locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by

emailing or writing to [email protected], Briggs & Stratton

Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.

The warranty period begins on the original date of purchase by the first retail or

commercial consumer. "Consumer use" means personal residential household use by a

retail consumer. "Commercial use" means all other uses, including use for commercial,

income producing or rental purposes. Once an engine has experienced commercial

use, it shall thereafter be considered as a commercial use engine for purposes of this

warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial

purchase date at the time warranty service is requested, the manufacturing date

of the product will be used to determine the warranty period. Product registration

is not required to obtain warranty service on Briggs & Stratton products.

About Your Warranty

This limited warranty covers engine-related material and/or workmanship issues only,

and not replacement or refund of the equipment to which the engine may be mounted.

Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered

under this warranty. Similarly, warranty is not applicable if the engine has been altered

or modified or if the engine serial number has been defaced or removed. This warranty

does not cover engine damage or performance problems caused by:

1. The use of parts that are not original Briggs & Stratton parts;

2. Operating the engine with insufficient, contaminated, or an incorrect grade of

lubricating oil;

3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater than

10%, or the use of alternative fuels such as liquefied petroleum or natural gas on

engines not originally designed/manufactured by Briggs & Stratton to operate on

such fuels;

4. Dirt which entered the engine because of improper air cleaner maintenance or re-

assembly;

5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly

installed blade adapters, impellers, or other crankshaft coupled devices, or

excessive v-belt tightness;

6. Associated parts or assemblies such as clutches, transmissions, equipment

controls, etc., which are not supplied by Briggs & Stratton;

7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or

clog the cooling fins or flywheel area, or by operating the engine without sufficient

ventilation;

8. Excessive vibration due to over-speeding, loose engine mounting, loose or

unbalanced cutter blades or impellers, or improper coupling of equipment

components to the crankshaft;

9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of

equipment, or improper engine installation.

10 vanguardpower.com

Not for

Reproduction

Warranty service is available only through Briggs & Stratton Authorized Service

Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map

at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).

80004537 (Rev. F)

Briggs & Stratton Emissions Warranty

California, U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty -

Your Warranty Rights and Obligations

For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-

Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)

The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are

pleased to explain the exhaust emissions (“emissions”) control system warranty on

your 2020-2022 engine. In California, new small off-road engines and large spark

ignited engines less than or equal to 1.0 liter must be designed, built, and equipped

to meet the State’s stringent anti-smog standards. B&S must warrant the emissions

control system on your engine for the periods of time listed below provided there has

been no abuse, neglect or improper maintenance of your small off-road engine or

equipment leading to the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-

injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid

fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated

components. Also included may be hoses, belts, connectors, and other emission-

related assemblies.

Where a warrantable condition exists, B&S will repair your engine at no cost to you

including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

The exhaust emissions control system on your engine is warranted for two years.

If any emissions-related part on your engine is defective, the part will be repaired or

replaced by B&S.

Owner’s Warranty Responsibilities:

• As the engine owner, you are responsible for the performance of the required

maintenance listed in your owner’s manual. B&S recommends that you retain

all receipts covering maintenance on your engine, but B&S cannot deny

warranty coverage solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.

• As the engine owner, you should however be aware that B&S may deny you

warranty coverage if your engine or a part has failed due to abuse, neglect, or

improper maintenance or unapproved modifications.

• You are responsible for presenting your engine to a B&S distribution center

or service center as soon as the problem exists. The warranty repairs shall

be completed in a reasonable amount of time, not to exceed 30 days. If you

have a question regarding your warranty rights and responsibilities, you should

contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty

Coverage. It is in addition to the B&S engine warranty for non-regulated engines found

in the Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor or fuel injection system

• Oxygen sensor

• Electronic control unit

• Fuel pump module

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse value

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

• Electronic controls

2. Length of Coverage

Coverage is for a period of two years from the date of delivery to an ultimate

purchaser, or for the time period listed in the respective engine or product warranty

statement, whichever is greater. B&S warrants to the original purchaser and each

subsequent purchaser that the engine is designed, built, and equipped so as to

conform with all applicable regulations adopted by the Air Resources Board; that

it is free from defects in material and workmanship that could cause the failure

of a warranted part; and that it is identical in allmaterial respects to the engine

described in the manufacturer’s application for certification. The warranty period

begins on the date the engine or equipment is delivered to an ultimate purchaser.

The warranty on emissions-related parts is as follows:

• Any warranted part that is not scheduled for replacement as required

maintenance in the Operator’s Manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to

the owner. Any such part repaired or replaced under the warranty will be

warranted for the remaining warranty period.

• Any warranted part that is scheduled only for regular inspection in the

Operator’s Manual supplied, is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be warranted

for the remaining warranty period.

• Any warranted part that is scheduled for replacement as required

maintenance in the Operators’s Manual supplied, is warranted for the period

of time prior to the first scheduled replacement point for that part. If the

part fails prior to the first scheduled replacement, the part will be repaired

or replaced by B&S at no charge to the owner. Any such part repaired or

replaced under warranty will be warranted for the remainder of the period

prior to the first scheduled replacement point for the part.

• Add-on or modified parts that are not exempted by the Air Resources Board

may not be used. The use of any non-exempted add-on or modified parts by

the owner will be grounds for disallowing a warranty claim. The manufacturer

will not be liable to warrant failures of warranted parts caused by the use of a

non-exempted add-on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions

parts that are not original equipment B&S parts or to parts that fail due to abuse,

neglect, or improper maintenance as set forth in the B&S engine warranty policy.

B&S is not liable for warranty coverage of failures of emissions parts caused by

the use of add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information On

Your Small Off-Road Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) small off-

road Emissions Standard must display information regarding the Emissions Durability

Period and the Air Index. Briggs & Stratton makes this information available to the

consumer on our emissions labels. The engine emissions label will indicate certification

information.

The Emissions Durability Period describes the number of hours of actual running

time for which the engine is certified to be emissions compliant, assuming proper

maintenance in accordance with the Operator’s Manual. The following categories are

used:

Moderate:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

50 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 125 hours of actual engine running time.

Intermediate:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

125 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 250 hours of actual engine running time.

Extended:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

300 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.

Therefore, the Emissions Durability Period of an engine with an intermediate rating

would equate to 10 to 12 years.

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions

Compliance Period referred to on the Emissions Compliance label indicates the

number of operating hours for which the engine has been shown to meet Federal

emissions requirements.

Not for

Reproduction

For engines at or less than 80 cc displacement:

Category C = 50 hours, Category B = 125 hours, Category A = 300 hours

For engines greater than 80 cc displacement and less than 225 cc displacement:

Category C = 125 hours, Category B = 250 hours, Category A = 500 hours

For engines of 225 cc or more displacement:

Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours

80099153(Revision A)

Briggs & Stratton Emissions Warranty

U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty Statement -

Your Warranty Rights and Obligations

For Briggs & Stratton Engine Models with "J" Trim Designation (Model-Type-

Trim Representation xxxxxx xxxx Jx)

The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the exhaust

emissions control system warranty on your Model Year 2020-2022 engine. In the U.S,

new small off-road engines and large spark ignited engines less than or equal to 1.0

liter must be designed, built, and equipped to meet stringent anti-smog standards. B&S

must warrant the emissions control system on your engine for the periods of time listed

below provided there has been no abuse, neglect, or improper maintenance of your

engine leading to the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-

injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid

fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated

components. Also included may be hoses, belts, connectors, and other emission-

related assemblies.

Where a warrantable condition exists, B&S will repair your engine at no cost to you

including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

The exhaust emissions control system on your engine is warranted for two years. If

any emissions-related parts on your engine is defective, the part will be repaired of

replaced by B&S.

Owner’s Warranty Responsibilities:

• As the engine owner, you are responsible for the performance of the required

maintenance listed in your Operator’s Manual. B&S recommends that you

retain all receipts covering maintenance on your engine, but B&S cannot deny

warranty coverage solely for the lack of receipts or your failure to ensure the

performance of all scheduled maintenance.

• As the engine owner, you should however be aware that B&S may deny you

warranty coverage if your engine or a part has failed due to abuse, neglect,

improper maintenance, or unapproved modifications.

• You are responsible for presenting your engine to a B&S distribution center,

or service center, as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days. If you

have a question regarding your warranty rights and responsibilities, you should

contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.com.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty

Coverage. It is in addition to the B&S engine warranty for non-regulated engines found

in the Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor or fuel injection system

• Oxygen sensor

• Electronic control unit

• Fuel pump module

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse value

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

• Electronic controls

2. Length of Coverage

Coverage is for a period of two years from the date of delivery to an ultimate

purchaser, or for the period listed in the respective engine or product warranty

statement, whichever is greater. B&S warrants to the original purchaser and each

subsequent purchaser that the engine is designed, built, and equipped so as to

conform with all applicable regulations under Section 213 of the Clean Air Act that

is free from defects in material and workmanshipthat could cause the failure of a

warranted part; and that is identical in all material respects to the engine described

in the manufacturer’s application for certification. The warranty period begins on

the date the engine or equipment is delivered to an ultimate purchaser.

The warranty on emissions-related parts is as follows:

• Any warranted part that is not scheduled for replacement as required

maintenance in the Operator’s Manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to

the owner. Any such part repaired or replaced under the warranty will be

warranted for the remaining warranty period.

• Any warranted part that is scheduled only for regular inspection in the

Operator’s Manual supplied, is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be warranted

for the remaining warranty period.

• Any warranted part that is scheduled for replacement as required

maintenance in the Operator's Manual supplied, is warranted for the period of

time prior to the first scheduled replacement point for that part. If the part fails

prior to the first scheduled replacement, the part will be repaired or replaced

by B&S at no charge to the owner. Any such part repaired or replaced under

warranty will be warranted for the remainder of the period prior to the first

scheduled replacement point for the part.

• Add-on or modified parts that are not exempted by the U.S. EPA may not be

used. The use of any non-exempted add-on or modified parts by the owner

will be grounds for disallowing a warranty claim. The manufacturer will not

be liable to warrant failures of warranted parts caused by the use of a non-

exempted add-on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions

parts that are not original equipment B&S parts or to parts that fail due to abuse,

neglect, or improper maintenance as set forth in the B&S engine warranty policy.

B&S is not liable for warranty coverage of failures of emissions parts caused by

the use of add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information On

Your Small Off-Road Engine Emissions Label

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 3 emissions standards. The Emissions Compliance

Period referred to on the Emissions Compliance label indicates the number of

operating hours for which the engine has been shown to meet Federal emissions

requirements.

For engines at or less than 80 cc displacement:

Category C = 50 hours, Category B = 125 hours, Category A = 300 hours

For engines greater than 80 cc displacement and less than 225 cc displacement:

Category C = 125 hours, Category B = 250 hours, Category A = 500 hours

For engines of 225 cc or more displacement:

Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours

80099149 (Revision A)

12 vanguardpower.com

Not for

Reproduction

Informasi Umum

Panduan ini berisi informasi keselamatan agar Anda mengetahui bahaya dan risiko

terkait mesin ini dan cara mencegahnya. Panduan ini juga berisi petunjuk tentang

cara penggunaan dan perawatan mesin yang benar. Karena Briggs & Stratton tidak

mengetahui peralatan yang akan digerakkan oleh mesin ini, Anda harus membaca,

memahami, serta mematuhi petunjuk ini. Simpan petunjuk asli ini untuk referensi

pada waktu mendatang.

PERHATIKAN:Angka-angka dan ilustrasi dalam panduan ini hanya sebagai referensi

dan mungkin saja berbeda dari model yang Anda miliki. Apabila Anda butuh bantuan,

hubungi Penyalur Servis Resmi.

Untuk suku cadang pengganti atau bantuan teknis, catat tanggal pembelian, model, tipe,

trim, dan nomor seri mesin. Nomor tersebut berada di mesin Anda. Baca bagian Fitur

dan Kontrol.

Tanggal Pembelian

Model - Tipe - Trim Mesin

Nomor Seri Mesin

Informasi Daur Ulang

Daur ulang semua kardus, kotak, oli bekas, dan baterai

sesuai peraturan pemerintah.

Keselamatan Operator

Simbol Peringatan dan Kata-kata Sinyal Terkait

Keselamatan

Simbol peringatan keselamatan mengidentifikasi informasi keselamatan

tentang bahaya yang dapat menyebabkan cedera pribadi. Kata peringatan (BAHAYA,

PERINGATAN, atau PERHATIAN) digunakan untuk mengindikasikan kemungkinan

dan keparahan potensi cedera. Selain itu, simbol bahaya digunakan untuk mewakili

tipe bahaya.

BAHAYA mengindikasikan bahaya yang, jika tidak dihindari, akan mengakibatkan

kematian atau cedera serius.

PERINGATAN mengindikasikan bahaya yang, jika tidak dihindari, dapat

mengakibatkan kematian atau cedera serius.

PERHATIAN mengindikasikan bahaya yang, jika tidak dihindari, dapat mengakibatkan

cedera ringan atau sedang.

PEMBERITAHUAN mengindikasikan informasi yang dianggap penting namun tidak

berkaitan dengan bahaya.

Simbol Keselamatan dan Artinya

Informasi keselamatan

mengenai bahaya yang

dapat mengakibatkan

cedera diri.

Baca dan pahami Panduan

Operator sebelum

mengoperasikan atau

menyervis unit.

Bahaya Kebakaran Bahaya Ledakan

Bahaya Sengatan Listrik Bahaya Asap Beracun

Bahaya Permukaan Panas Bahaya Kebisingan-

Pelindung telinga

direkomendasikan untuk

penggunaan jangka

panjang.

Bahaya Benda Terlempar-

Kenakan pelindung mata.

Bahaya Ledakan

Bahaya Radang Beku Bahaya Hentakan Balik

Bahaya Amputasi-

Komponen yang Bergerak

Bahaya Bahan Kimia

Bahaya Panas Termal Bahaya Korosi

Pesan Keselamatan

PERINGATAN

Mesin Briggs & Stratton® tidak dirancang untuk dan tidak boleh digunakan untuk

menggerakkan: fun-kart; go-kart; kendaraan segala medan (all-terrain vehicle, ATV)

untuk olahraga, rekreasi, atau anak-anak; sepeda motor; kapal bantalan udara;

produk pesawat; atau kendaraan yang digunakan pada acara pertandingan yang tidak

disetujui oleh Briggs & Stratton. Untuk informasi mengenai produk balap kompetitif, lihat

www.briggsracing.com. Untuk penggunaan dengan utilitas dan ATV berdampingan,

hubungilah Pusat Penerapan Daya Briggs & Stratton, 1-866-927-3349. Kesalahan

penggunaan mesin dapat menyebabkan cedera serius atau kematian.

PERINGATAN

Bahan bakar dan uapnya mudah terbakar dan meledak. Kebakaran atau ledakan

dapat mengakibatkan luka bakar atau kematian.

Apabila Anda menambahkan bahan bakar

• Matikan mesin. Sebelum melepas tutup bahan bakar, tunggu minimal dua (2)

menit untuk memastikan bahwa mesin sudah dingin.

• Isi tangki bahan bakar di luar ruangan atau di area yang memiliki aliran udara

yang baik.

• Jangan mengisi tangki bahan bakar terlalu penuh. Agar bahan bakar dapat

menyebar di dalam tangki, jangan lakukan pengisian di atas bagian dasar leher

tangki bahan bakar.

• Jauhkan bahan bakar dari percikan api, nyala api, lampu penunjuk, panas, dan

sumber pemicu api lainnya.

• Periksa saluran bahan bakar, tangki bahan bakar, tutup bahan bakar, dan

sambungan secara rutin untuk mengetahui jika ada retakan atau kebocoran.

Ganti bagian yang rusak.

• Apabila bahan bakar tumpah, tunggu hingga tumpahannya kering sebelum Anda

menyalakan mesin.

Saat Anda menyalakan mesin

• Pastikan busi, knalpot, tutup tangki, dan pembersih udara (jika ada) terpasang

dengan benar.

• Jangan memutar poros mesin dengan busi dilepas.

• Apabila mesin banjir, atur cuk (jika ada) ke posisi BUKA atau BERJALAN.

Pindahkan trotel (jika ada) ke posisi CEPAT dan putar hingga mesin menyala.

• Apabila terdapat kebocoran gas alam atau LP di suatu area, jangan menyalakan

mesin.

• Karena uapnya mudah terbakar, jangan menggunakan cairan starter

bertekanan.

Saat Anda mengoperasikan peralatan

• Jangan memiringkan mesin atau peralatan dengan sudut yang menyebabkan

bahan bakar tumpah.

• Jangan menggunakan cuk karburator (jika ada) untuk mematikan mesin.

• Jangan menyalakan dan mengoperasikan mesin tanpa pembersih udara (jika

ada) atau filter udara (jika ada).

Saat Anda melakukan pemeliharaan

• Apabila Anda menguras oli dari tabung pengisian oli atas, tangki bahan bakar

harus kosong. Apabila tidak dikosongkan, dapat terjadi kebocoran bahan

bakardan dapat menimbulkan kebakaran atau ledakan.

• Apabila unit perlu dimiringkan selama pemeliharaan, pastikan bahwa

tangki bahan bakar, jika terpasang pada mesin, kosong dan bahwa busi

menghadap ke atas. Apabila tangki bahan bakar tidak dikosongkan, dapat

terjadi kebocorandan dapat menimbulkan kebakaran atau ledakan.

• Periksa saluran bahan bakar, tangki bahan bakar, tutup bahan bakar, dan

sambungan secara rutin untuk mengetahui jika ada retakan atau kebocoran.

Ganti bagian yang rusak.

• Jangan mengganti pegas governor, sambungan, atau komponen lainnya untuk

menambah kecepatan mesin.

• Jangan memukul roda gila dengan palu atau benda yang keras. Hal ini dapat

mengakibatkan roda gila gagal beroperasi.

Not for

Reproduction

• Komponen pengganti harus sama dan dipasang pada posisi yang sama seperti

komponen asli. Komponen lain juga dapat mengakibatkan kerusakan atau

cedera.

Saat Anda memindahkan lokasi peralatan

• Pastikan tangki bahan bakar KOSONG atau katup pemutus aliran bahan bakar

berada dalam posisi TERTUTUP.

Saat bahan bakar atau peralatan disimpan dengan tangki terisi bahan bakar

• Karena lampu utama atau sumber pengapian dapat menimbulkan ledakan,

jauhkan bahan bakar atau peralatan dari tungku, kompor, alat pemanas air, atau

perangkat lainnya yang dilengkapi pemantik.

PERINGATAN

Bahan bakar dan uapnya mudah terbakar dan meledak. Kebakaran atau ledakan

dapat mengakibatkan luka bakar atau kematian.

Menyalakan mesin menimbulkan percikan yang dapat mengakibatkan kebakaran

atau ledakan.

• Apabila terdapat kebocoran gas alam atau LP di suatu area, jangan menyalakan

mesin.

• Karena uapnya mudah terbakar, jangan menggunakan cairan starter

bertekanan.

PERINGATAN

BAHAYA GAS BERACUN. Gas buang mesin mengandung karbon monoksida,

yakni gas beracun yang dapat mematikan dalam hitungan menit. Meskipun Anda

tidak mencium asap gas buang, Anda tetap dapat terpapar gas karbon monoksida

berbahaya. Apabila Anda merasa tidak enak badan, pusing, atau lemas saat

menggunakan produk ini, SEGERA cari udara segar. Kunjungi dokter. Anda

mungkin keracunan karbon monoksida.

• Gas karbon monoksida dapat menumpuk di ruang berpenghuni. Untuk

mengurangi risiko terkumpulnya gas karbon monoksida, HANYA operasikan

produk ini di luar ruangan dan jauh dari jendela, pintu, dan ventilasi.

• Pasanglah alarm karbon monoksida bertenaga baterai atau sambungkan alarm

karbon monoksida ke stopkontak listrik dengan baterai cadangan sebagaimana

ditetapkan oleh instruksi produsen. Alarm asap tidak dapat mengetahui gas

karbon monoksida.

• JANGAN mengoperasikan produk ini di dalam rumah, garasi, ruang bawah

tanah, kolong, gudang, atau ruang tertutup lainnya, bahkan jika Anda

menggunakan kipas angin atau pintu dan jendela terbuka sebagai ventilasi.

Setelah mengoperasikan produk ini, karbon monoksida dapat dengan cepat

berkumpul di ruang ini dan menetap selama berjam-jam.

• SELALU letakkan produk ini sesuai arah angin dan posisikan saluran gas buang

mesin menjauh dari tempat hunian manusia.

PERINGATAN

Penarikan tali starter (hentakan balik) yang cepat akan menarik tangan dan lengan

menuju mesin lebih cepat dari usaha Anda untuk melepaskannya. Hal ini dapat

menyebabkan patah tulang, tulang retak, memar, atau terkilir.

• Untuk menghindari hentakan balik saat Anda menyalakan mesin, tarik tali starter

perlahan-lahan sampai dirasakan tertahan dan kemudian tarik dengan cepat.

• Sebelum menyalakan mesin, putuskan sambungan atau lepaskan semua beban

peralatan dan mesin eksternal.

• Pastikan bahwa komponen peralatan yang digabungkan langsung seperti,

namun tidak terbatas pada, pisau, impeler, puli, dan sproket terpasang dengan

benar.

PERINGATAN

Komponen yang berputar dapat menjerat tangan, kaki, rambut, pakaian, atau

aksesori dan mengakibatkan amputasi traumatik atau laserasi.

• Operasikan peralatan dengan pengaman yang terpasang dengan benar.

• Jauhkan tangan dan kaki dari komponen yang berputar.

• Lepas perhiasan dan pastikan rambut panjang jauh dari setiap komponen yang

berputar.

• Jangan mengenakan pakaian longgar atau benda yang dapat terjerat.

PERINGATAN

Selama pengoperasian, mesin dan knalpot menjadi panas. Apabila Anda

menyentuh mesin yang panas, luka bakar panas dapat terjadi.

Bahan yang mudah terbakar, seperti daun, rumput, dan sikat, dapat tersulut api.

• Sebelum Anda menyentuh mesin atau knalpot, matikan mesin dan tunggu dua

(2) menit. Pastikan mesin dan knalpot aman disentuh.

• Bersihkan kotoran dari knalpot dan mesin.

Merupakan pelanggaran California Public Resource Code, Pasal 4442, jika

menggunakan atau mengoperasikan mesin di lahan yang tertutup hutan, tertutup

semak, atau tertutup rumput kecuali sistem gas buang dilengkapi dengan pelindung

percikan (spark arrester), sebagaimana disebutkan dalam pasal 4442, yang dirawat

dan dapat bekerja dengan baik. Yurisdiksi negara bagian atau federal lainnya

mungkin memiliki undang-undang yang sama; referensi Peraturan Federal 36CFR

Bagian261.52. Hubungi produsen peralatan asli, peritel, atau dealer untuk memperoleh

spark arrester yang dirancang untuk sistem pembuangan yang dipasang pada mesin ini.

PERINGATAN

Percikan mesin yang tidak disengaja dapat menyebabkan sengatan listrik atau

kebakaran dan dapat mengakibatkan belitan, amputasi traumatik, dan laserasi.

Sebelum melakukan penyesuaian atau perbaikan:

• Lepas kabel busi dan jauhkan dari busi.

• Lepas kabel baterai pada terminal negatif baterai (hanya pada mesin dengan

penstarteran elektrik).

• Gunakan hanya alat yang tepat.

Saat memeriksa percikan:

• Gunakan tester busi yang disetujui.

• Jangan periksa percikan listrik saat busi dilepas.

PERINGATAN

Uap bahan bakar mudah terbakar dan meledak. Kebakaran atau ledakan dapat

mengakibatkan luka bakar atau kematian.

Apabila Anda mencium bau gas

• Jangan menyalakan mesin.

• Jangan menyalakan sakelar listrik.

• Jangan menggunakan telepon di dekatnya.

• Evakuasi area.

• Hubungi pemasok gas atau pemadam kebakaran.

Fitur dan Kontrol

Kontrol Mesin

Bandingkan huruf timbul dalam Gambar 1, 2, 3, dan 4 dengan kontrol mesin dalam

daftar berikut:

A. Nomor Identifikasi MesinModel - Tipe - Kode

B. Busi

C. Pembersih Udara Siklonik

D. Pembersih Udara Profil Rendah

E. Stik Pengukur Oli

F. Pengisian Oli

G. Filter Oli

H. Penyumbat Oli

I. Sensor Tekanan Oli

J. Pelindung Jari

K. Starter Elektrik

L. Solenoid Starter

M. Regulator/Penyearah

N. Karburator - Model Karburator

O. Pendingin Oli (jika dipasang)

P. Knalpot (jika dilengkapi)

Q. Pompa Bahan Bakar

Sakelar Starter

Kontrol Trotel

Kontrol Cuk (Model Karburator

)

U. Filter Bahan Bakar

V. Takometer (jika dilengkapi)

Beberapa mesin dan peralatan memiliki kendali jarak jauh. Lihat panduan peralatan

untuk mendapatkan informasi tentang lokasi dan pengoperasian kendali jarak jauh.

14 vanguardpower.com

Not for

Reproduction

Simbol Kontrol Mesin dan Artinya

Kecepatan Mesin- CEPAT Kecepatan Mesin-

LAMBAT

Kecepatan Mesin-

BERHENTI

NYALA- MATI

Starter Mesin

Cuk TUTUP

Starter Mesin

Cuk BUKA

Tutup Bahan Bakar

Penutup Bahan Bakar

BUKA

Penutup Bahan Bakar

TUTUP

Level Bahan Bakar-

Maksimum

Jangan Mengisi Terlalu

Penuh

Operasi

Rekomendasi Oli

Kapasitas Oli: Lihat bagian Spesifikasi.

PEMBERITAHUAN

Mesin ini dikirim tanpa oli dari Briggs & Stratton. Produsen atau penyalur peralatan

mungkin telah menambahkan oli pada mesin. Sebelum Anda menyalakan mesin untuk

pertama kali, pastikan oli pada ketinggian yang benar. Tambahkan oli sesuai dengan

instruksi pada panduan ini. Apabila Anda menyalakan mesin tanpa oli, kerusakan akan

terjadi pada mesain dan perbaikan mesin tidak akan ditanggung dengan garansi.

Kami menyarankan Anda agar menggunakan Oli Resmi Bergaransi Briggs &

Stratton

untuk mendapatkan performa terbaik. Oli detergen berkualitas tinggi lainnya

diperbolehkan jika tergolong untuk servis SF, SG, SH, SJ atau yang lebih tinggi. Jangan

gunakan bahan aditif khusus.

Gunakan bagan berikut untuk memilih viskositas terbaik untuk perkiraan kisaran suhu

luar ruangan. Mesin pada peralatan daya luar ruangan cocok dengan Oli Sintetis

5W-30. Untuk peralatan yang dioperasikan pada suhu panas, oli Sintetis Vanguard

15W-50 memberikan perlindungan yang terbaik.

A SAE 30 - Pada suhu di bawah 40°F (4°C), penggunaan oli SAE30 akan

mengakibatkan penstarteran yang sulit.

B 10W-30 - Pada suhu di atas 80°F (27°C), penggunaan oli 10W-30 dapat

menyebabkan bertambahnya konsumsi oli. Periksaketinggian oli sesering

mungkin.

C 5W-30

D Sintetis 5W-30

Sintetis 15W-50 Vanguard

Cek dan Tambah Oli

Sebelum Anda memeriksa atau menambahkan oli

• Pastikan mesin dalam posisi datar.

• Bersihkan bagian lubang pengisian oli dari kotoran.

• Baca bagian Spesifikasi untuk mengetahui kapasitas oli.

PEMBERITAHUAN

Mesin ini dikirim tanpa oli dari Briggs & Stratton. Produsen atau penyalur peralatan

mungkin telah menambahkan oli pada mesin. Sebelum Anda menyalakan mesin untuk

pertama kali, pastikan oli pada ketinggian yang benar. Tambahkan oli sesuai dengan

instruksi pada panduan ini. Apabila Anda menyalakan mesin tanpa oli, kerusakan akan

terjadi pada mesain dan perbaikan mesin tidak akan ditanggung dengan garansi.

1. Lepaskan stik pengukur oli (A, Gambar 5) dan bersihkan dengan kain bersih.

2. Pasang dan kencangkan stik pengukur oli (A, Gambar 5).

3. Lepaskan batang celup dan periksa level oli. Pastikan ketinggian oli berada di

bagian atas indikator penuh (B, Gambar 5) dari stik pengukur oli.

4. Apabila ketinggian oli rendah, tuangkan oli perlahan-lahan ke dalam lubang

pengisian oli pada mesin (C, Gambar5). Jangan menambahkan terlalu banyak

oli. Setelah menambahkan oli, tunggu selama satu menit dan kemudian periksa

kembali ketinggian oli. Pastikan ketinggian oli berada di bagian yang tepat.

5. Pasang dan kencangkan stik pengukur oli (A, Gambar 5).

Sistem Perlindungan Ketinggian Oli Rendah (jika

dilengkapi)

Sensor ketinggian oli rendah dipasang pada beberapa mesin. Apabila oli rendah, sensor

akan mengaktifkan lampu peringatan atau mematikan mesin. Matikan mesin dan ikuti

langkah berikut sebelum menyalakan mesin.

• Pastikan mesin dalam posisi datar.

• Lakukan pemeriksaan oli. Baca bagian Periksa Ketinggian Oli.

• Apabila ketinggian oli rendah, tambahkan oli dalam jumlah yang tepat. Nyalakan

mesin dan pastikan lampu peringatan (jika dilengkapi) tidak menyala.

• Apabila ketinggian oli tidak rendah, jangan menyalakan mesin. Hubungi

Penyalur Servis Resmi Briggs & Stratton untuk menyelesaikan masalah oli.

Rekomendasi Bahan Bakar

Bahan bakar harus memenuhi persyaratan berikut:

• Bensin bersih, baru, dan tanpa timbal.

• Nilai oktan minimal 87/87AKI (91RON). Penggunaan di lokasi yang tinggi, lihat

di bawah.

• Bensin dengan kandungan hingga 10% etanol (gasohol) diperbolehkan.

PEMBERITAHUAN

Jangan menggunakan bensin yang tidak disetujui, seperti E15 dan E85. Jangan

mencampurkan oli ke dalam bensin atau memodifikasi mesin untuk beroperasi

dengan bahan bakar pengganti. Penggunaan bahan bakar yang tidak disetujui akan

menyebabkan kerusakan pada komponen mesin, yang tidak akan diperbaiki sesuai

garansi.

Untuk melindungi sistem bahan bakar dari pembentukan endapan, campurkan bahan

stabilisator bahan bakar ke dalam bahan bakar. Baca bagian Penyimpanan. Tidak

semua bahan bakar sama. Apabila terjadi masalah penstarteran atau performa, ganti

dengan penyedia atau merek bahan bakar lain. Mesin ini disertifikasi untuk beroperasi

dengan bensin. Sistem kontrol emisi untuk mesin berkarburator adalah EM (Modifikasi

Mesin). Sistem kontrol emisi untuk mesin dengan injeksi bahan bakar elektronik adalah

ECM (Modul Kontrol Mesin), MPI (Injeksi Multi-Port), dan jika dilengkapi O2S (Sensor

Oksigen).

Lokasi yang Tinggi

Di lokasi dengan ketinggian lebih dari 5.000kaki (1524meter), bensin dengan

minimum 85oktan/85AKI (89RON) diperbolehkan.

Untuk mesin berkarburator, penyetelan diperlukan di lokasi yang tinggi guna

mempertahankan performa. Pengoperasian tanpa penyetelan ini akan menyebabkan

performa berkurang, konsumsi bahan bakar bertambah, dan emisi meningkat. Hubungi

Penyalur Servis Resmi Briggs & Stratton untuk mengetahui informasi penyetelan

di lokasi yang tinggi. Pengoperasian mesin di lokasi dengan ketinggian kurang dari

2.500kaki (762meter) dengan kit lokasi yang tinggi tidak disarankan.

Mesin Injeksi Bahan Bakar Elektronik (EFI) tidak memerlukan penyetelan lokasi

ketinggian.

Not for

Reproduction

Tambahkan Bahan Bakar

PERINGATAN

Bahan bakar dan uapnya mudah terbakar dan meledak. Kebakaran atau ledakan

dapat mengakibatkan luka bakar atau kematian.

Apabila Anda menambahkan bahan bakar

• Matikan mesin. Sebelum melepas tutup bahan bakar, tunggu minimal dua (2)

menit untuk memastikan bahwa mesin sudah dingin.

• Isi tangki bahan bakar di luar ruangan atau di area yang memiliki aliran udara

yang baik.

• Jangan mengisi tangki bahan bakar terlalu penuh. Agar bahan bakar dapat

menyebar di dalam tangki, jangan lakukan pengisian di atas bagian dasar leher

tangki bahan bakar.

• Jauhkan bahan bakar dari percikan api, nyala api, lampu penunjuk, panas, dan

sumber pemicu api lainnya.

• Periksa saluran bahan bakar, tangki bahan bakar, tutup bahan bakar, dan

sambungan secara rutin untuk mengetahui jika ada retakan atau kebocoran.

Ganti bagian yang rusak.

• Apabila bahan bakar tumpah, tunggu hingga tumpahannya kering sebelum Anda

menyalakan mesin.

1. Bersihkan bagian lubang pengisian oli dari kotoran dan serpihan. Lepas tutup

bahan bakar.

2. Isi tangki bahan bakar (A, Gambar 6) dengan bahan bakar. Karena bahan bakar

akan menguap, jangan mengisi di atas bagian dasar leher tangki bahan bakar(B).

3. Pasang kembali tutup tangki bahan bakar.

Hidupkan dan Matikan Mesin

Hidupkan Mesin

PERINGATAN

Penarikan tali starter (hentakan balik) yang cepat akan menarik tangan dan

lengan menuju mesin lebih cepat dari usaha Anda untuk melepaskannya. Hal ini

dapat menyebabkan patah tulang, tulang retak, memar, atau terkilir.

• Untuk menghindari hentakan balik saat Anda menyalakan mesin, tarik tali

starter perlahan-lahan sampai dirasakan tertahan dan kemudian tarik dengan

cepat.

• Sebelum menyalakan mesin, putuskan sambungan atau lepaskan semua

beban peralatan dan mesin eksternal.

• Pastikan bahwa komponen peralatan yang digabungkan langsung seperti,

namun tidak terbatas pada, pisau, impeler, puli, dan sproket terpasang dengan

benar.

PERINGATAN

Bahan bakar dan uapnya mudah terbakar dan meledak. Kebakaran atau ledakan

dapat mengakibatkan luka bakar atau kematian.

Saat Anda menyalakan mesin

• Pastikan busi, knalpot, tutup tangki, dan pembersih udara (jika ada) terpasang

dengan benar.

• Jangan memutar poros mesin dengan busi dilepas.

• Apabila mesin banjir, atur cuk (jika ada) ke posisi BUKA atau BERJALAN.

Pindahkan trotel (jika ada) ke posisi CEPAT dan putar hingga mesin menyala.

• Apabila terdapat kebocoran gas alam atau LP di suatu area, jangan

menyalakan mesin.

• Karena uapnya mudah terbakar, jangan menggunakan cairan starter

bertekanan.

PERINGATAN

BAHAYA GAS BERACUN. Gas buang mesin mengandung karbon monoksida,

yakni gas beracun yang dapat mematikan dalam hitungan menit. Meskipun

Anda tidak mencium asap gas buang, Anda tetap dapat terpapar gas karbon

monoksida berbahaya. Apabila Anda merasa tidak enak badan, pusing, atau

lemas saat menggunakan produk ini, SEGERA cari udara segar. Kunjungi dokter.

Anda mungkin keracunan karbon monoksida.

• Gas karbon monoksida dapat menumpuk di ruang berpenghuni. Untuk

mengurangi risiko terkumpulnya gas karbon monoksida, HANYA operasikan

produk ini di luar ruangan dan jauh dari jendela, pintu, dan ventilasi.

• Pasanglah alarm karbon monoksida bertenaga baterai atau sambungkan alarm

karbon monoksida ke stopkontak listrik dengan baterai cadangan sebagaimana

ditetapkan oleh instruksi produsen. Alarm asap tidak dapat mengetahui gas

karbon monoksida.

• JANGAN mengoperasikan produk ini di dalam rumah, garasi, ruang bawah

tanah, kolong, gudang, atau ruang tertutup lainnya, bahkan jika Anda

menggunakan kipas angin atau pintu dan jendela terbuka sebagai ventilasi.

Setelah mengoperasikan produk ini, karbon monoksida dapat dengan cepat

berkumpul di ruang ini dan menetap selama berjam-jam.

• SELALU letakkan produk ini sesuai arah angin dan posisikan saluran gas

buang mesin menjauh dari tempat hunian manusia.

PEMBERITAHUAN

Mesin ini dikirim tanpa oli dari Briggs & Stratton. Produsen atau penyalur peralatan

mungkin telah menambahkan oli pada mesin. Sebelum Anda menyalakan mesin untuk

pertama kali, pastikan oli pada ketinggian yang benar. Tambahkan oli sesuai dengan

instruksi pada panduan ini. Apabila Anda menyalakan mesin tanpa oli, kerusakan akan

terjadi pada mesain dan perbaikan mesin tidak akan ditanggung dengan garansi.

Tipe Sistem Penyalaan

Sebelum menyalakan mesin, Anda harus mengetahui tipe sistem penyalaan mesin

Anda. Mesin Anda memiliki salah satu tipe sistem penyalaan berikut.

• Sistem Injeksi Bahan Bakar Elektronik (EFI): Sistem EFI tidak memiliki cuk

atau pemancing.

• Sistem Cuk: Tipe sistem ini memiliki cuk untuk digunakan pada suhu dingin.

Beberapa model memiliki kontrol cuk terpisah sementara yang lainnya memiliki

kombinasi cuk dan trotel. Mesin ini tidak memiliki pemancing.

PERHATIKAN:Peralatan Anda mungkin memiliki kontrol jarak jauh. Baca panduan

peralatan untuk mendapatkan informasi tentang lokasi dan pengoperasian kontrol jarak

jauh.

Sistem Injeksi Bahan Bakar Elektronik (EFI)

1. Periksa oli mesin. Lihat bagianPeriksa Level Oli.

2. Pastikan kontrol penggerak peralatan, jika ada, dalam kondisi nonaktif.

3. Pindahkan pemutus aliran bahan bakar (A, Gambar 7), jika dilengkapi, ke posisi

BUKA.

4. Pindahkan kontrol trotel (B, Gambar 7), jika dilengkapi, ke posisi CEPAT.

Operasikan mesin pada posisi CEPAT.

5. Putar sakelar penstarteran elektrik (D, Gambar 7) ke posisi ON atau MULAI.

PEMBERITAHUANUntuk memperpanjang umur pakai starter, gunakan siklus starter

singkat (maksimum lima detik). Tunggu satu menit antar siklus starter.

Apabila mesin tidak menyala setelah 3atau 4 kali percobaan, hubungi penyalur

setempat Anda ataukunjungi vanguardpower.com, atau hubungi 1-800-999-9333.

Sistem Cuk

1. Periksa oli mesin. Lihat bagianPeriksa Level Oli.

2. Pastikan kontrol penggerak peralatan, jika ada, dalam kondisi nonaktif.

3. Pindahkan pemutus aliran bahan bakar (A, Gambar 7), jika dilengkapi, ke posisi

BUKA.

4. Pindahkan kontrol trotel (B, Gambar 7), jika dilengkapi, ke posisi CEPAT.

Operasikan mesin pada posisi CEPAT.

5. Pindahkan kontrol cuk (C, Gambar 7), atau kombinasi cuk dan trotel (B,C) ke posisi

TERTUTUP.

PERHATIKAN:Untuk menyalakan mesin dengan sistem bahan bakar kering, waktu

pemutaran poros engkol tambahan pada posisi cuk diperlukan. Ini akan memberikan

pompa bahan bakar untuk memancing sistem bahan bakar.

6. Putar sakelar kunci (D, Gambar 7) ke posisi ON atau MULAI.

7. Apabila mesin menyala tetapi tidak terus beroperasi, pindahkan kontrol cuk (C,

Gambar 7) ke posisi BUKA untuk menyalakan mesin.

PEMBERITAHUANUntuk memperpanjang umur pakai starter, gunakan siklus starter

singkat (maksimum lima detik). Tunggu satu menit antar siklus starter.

16 vanguardpower.com

Not for

Reproduction

8. Setelah mesin panas, pindahkan kontrol cuk (C, Gambar 7) ke posisi BUKA.

Apabila mesin tidak menyala setelah 3atau 4 kali percobaan, hubungi penyalur

setempat Anda ataukunjungi vanguardpower.com, atau hubungi 1-800-999-9333.

Matikan Mesin

PERINGATAN

Bahan bakar dan uapnya mudah terbakar dan meledak. Kebakaran atau ledakan

dapat mengakibatkan luka bakar atau kematian.

• Jangan menggunakan cuk karburator (jika ada) untuk mematikan mesin.

1. Dengan kontrol trotel dalam posisi LAMBAT, putar sakelar penstarteran elektrik

(D, Gambar7) ke posisi MATI. Lepas kunci dan simpan di tempat aman, jauh dari

jangkauan anak-anak.

2. Setelah mesin berhenti, putar katup pemutus aliran bahan bakar (A, Gambar 7), jika

dilengkapi, ke posisi TERTUTUP.

Pemeliharaan

Informasi Pemeliharaan

PERINGATAN

Apabila unit perlu dimiringkan selama pemeliharaan, pastikan bahwa tangki bahan

bakar, jika terpasang pada mesin, kosong dan bahwa busi menghadap ke atas. Apabila

tangki bahan bakar tidak dikosongkan, dapat terjadi kebocoran dan dapat menimbulkan

kebakaran atau ledakan. Apabila mesin dimiringkan ke arah yang berbeda, mesin akan

sulit dinyalakan karena kontaminasi oli atau bahan bakar pada filter udara atau busi.

Kami merekomendasikan Anda mengunjungi Penyalur Servis Resmi Briggs & Stratton

untuk semua pemeliharaan serta servis mesin dan komponen mesin.

PEMBERITAHUAN

Agar mesin beroperasi dengan baik, semua komponen mesin ini harus tetap pada

tempatnya.

PERINGATAN

Percikan mesin yang tidak disengaja dapat menyebabkan sengatan listrik atau

kebakaran dan dapat mengakibatkan belitan, amputasi traumatik, dan laserasi.

Sebelum melakukan penyesuaian atau perbaikan:

• Lepas kabel busi dan jauhkan dari busi.

• Lepas kabel baterai pada terminal negatif baterai (hanya pada mesin dengan

penstarteran elektrik).

• Gunakan hanya alat yang tepat.

Saat memeriksa percikan:

• Gunakan tester busi yang disetujui.

• Jangan periksa percikan listrik saat busi dilepas.

Layanan Kontrol Emisi

Untuk pemeliharaan, penggantian, atau perbaikan perangkat dan sistem kontrol

emisi, hubungi perusahaan atau teknisi layanan perbaikan mesin medan berat

yang memenuhi syarat. Namun, untuk mendapatkan servis kontrol emisi “tanpa biaya”,

pekerjaan harus dilakukan oleh penyalur resmi pabrik. Baca Pernyataan Kontrol Emisi.

Jadwal Pemeliharaan

Setiap 8 Jam atau Setiap Hari

• Periksa ketinggian oli mesin.

• Bersihkan area di sekitar knalpot dan kontrol.

Setiap 100 Jam atau Setiap Tahun

•

Bersihkan atau ganti filter udara

1 2

• Ganti oli mesin dan filter.

• Ganti filter oli (jika dilengkapi).

• Ganti busi.

• Periksa knalpot dan pelindung percikan.

• Servis sistem gas buang.

Setiap 250 Jam atau Setiap Tahun

• Periksa jarak katup. Sesuaikan jika perlu.

Setiap 400 Jam atau Setiap Tahun

•

Ganti filter udara

• Ganti filter bahan bakar.

•

Servis sistem pendingin udara

•

Bersihkan sirip pendingin oli

Setiap 600 Jam

• Ganti filter pengaman, jika dilengkapi.

Bersihkan lebih sering jika dalam kondisi berdebu atau saat terdapat kotoran dari

udara.

Setiap penggantian filter udara ketiga, ganti filter pengaman dalam (jika dilengkapi).

Sistem Injeksi Bahan Bakar Elektronik (EFI)

Sistem EFI memantau suhu mesin, kecepatan mesin, dan tegangan baterai untuk

menyalakan serta memanaskan mesin. Tidak ada penyesuaian pada sistem. Apabila

terjadi masalah saat menyalakan atau mengoperasikan mesin, hubungi Penyalur Servis

Resmi Briggs & Stratton.

PEMBERITAHUANPastikan untuk mengikuti langkah berikut atau kerusakan sistem

EFI mungkin terjadi.

• JANGAN menyalakan mesin jika kabel baterai longgar.

• Putar kunci ke posisi MATI sebelum melepaskan sambungan, melepas, dan/

atau memasang baterai.

• JANGAN menggunakan pengisi daya baterai untuk menyalakan mesin.

• JANGAN melepaskan kabel baterai selama mengoperasikan mesin.

• Saat Anda melepaskan kabel baterai, pertama-tama sambungkan kabel positif

(+), lalu sambungkan kabel negatif (-) ke baterai.

• Saat Anda mengisi daya baterai, putar sakelar pengapian ke posisi MATI,dan

lepaskan kabel baterai negatif (-) dari baterai.

• JANGAN menyemprotkan air secara langsung pada Modul Kontrol Elektronik.

Karburator dan Kecepatan Mesin

Jangan mengubah setelan karburator atau kecepatan mesin. Karburator disetel di

pabrik agar beroperasi sebagaimana mestinya dalam sebagian besar kondisi. Jangan

mengganti pegas governor, penghubung, atau komponen lain untuk mengubah

kecepatan mesin. Apabila penyesuaian perlu dilakukan, hubungi Penyalur Servis Resmi

Briggs & Stratton untuk servis.

PEMBERITAHUAN

Produsen peralatan menentukan kecepatan maksimum untuk mesin saat dipasang

pada alat. Jangan melampaui kecepatan ini. Apabila Anda tidak yakin berapa

kecepatan maksimum mesin, atau berapa kecepatan mesin yang disetel dari pabriknya,

hubungi Penyalur Servis Resmi Briggs & Stratton untuk mendapatkan bantuan. Untuk

pengoperasian peralatan secara aman dan tepat, kecepatan mesin hanya boleh

disesuaikan oleh teknisi servis yang berkualifikasi.

Servis Busi

Periksa celah busi (A, gambar 8) dengan pengukur kabel (B). Apabila diperlukan, atur

celah busi. Pasang dan kencangkan busi ke torsi yang benar. Untuk memperoleh

spesifikasi celah atau torsi, baca bagian Spesifikasi.

PERHATIKAN:Di beberapa area, Anda diwajibkan untuk menggunakan busi resistor

untuk mengurangi sinyal pengapian. Jika busi resistor dipasang oleh produsen

peralatan, gunakan tipe resistor busi yang sama saat penggantian.

Servis SistemGas Buang