Bitspower BPTA-O11DEVO_A3.0-BK インストールガイド

Parts List

............1 pc

Intel Mounting Bracket

— 1 —

Bitspower reserves the right to change the product design and

interpretations. These are subject to change without notice. Product

colors and accessories are based on the actual product.

English

TITAN ONE EVO_3.0 Installation Guide

BPTA-O11DEVO_A3.0-WH

CPU Water Block

A

B-1 B-2

A-1

A-2

A-3

..........1 pc

BPTA-CPUMS-V2-SKA

A-1

A-2

...............1 set

Backplane assembly

A-3

Fittings

B

.................2 pcs

BPTA-DOTFH1622

B-1

....................2 pcs

BPTA-15ATFH16

B-2

Accessory

C

................................6 pcs

Hard tube

C-1

..............................1 pc

Drain Tube

C-2

A

B

C

CPU set

C-3

BP-CPUPDB-AMD5MS

C-5

Hard Tube

C-1

Drain Tube

C-2

V3

The allowable variance in tube length is ± 2mm

272

104

:16

The allowable variance in tube length is ± 2mm

275

104

:16

The allowable variance in tube length is ± 2mm

255

104

:16

BPTA-MKCPUMS-1700 or

BPTA-MKCPUMS-1700-V2

C-4

Thumb screw

SPRING

Thumb nut

1mm Spacer

M3x32mm Screw

SC6-32M3

Nylon cup washer

.................4 pcs

...........4 pcs

..................8 pcs

.....................4 pcs

.........................4 pcs

Please refer to the tables on pages 5 and 12

for Hard Tubes+Motherboard compatibility.

EX.

I. AMD Motherboard system

— 2 —

M3x32mm SCREW

(for Intel)

1mm SPACER

Back Pad

3M Paste Pad

Metal Backplane

Thumb screw

SPRING

CPU Block

1mm SPACER

Thumb screw

CPU Block

SC6-32M3

(for AMD AM4)

Nylon cup washer

(for AMD AM4)

Original

backplane

SPRING

1mm SPACER

Thumb Nut

96

90

48

54

AMD SOCKET AM4

AMD SOCKET AM3 / AM3+

AMD SOCKET AM2 / AM2+

AMD SOCKET FM1 / FM2+

AMD SOCKET 939 / 754 / 940

AMD SOCKET AM4

AMD SOCKET AM3 / AM3+

AMD SOCKET AM2 / AM2+

AMD SOCKET FM1 / FM2+

Installation

DRGB LED

IN

OUT

DRGB PIN on Motherboard or other equipment.

 

Motherboard

Fan and DRGB RF Remote

Controller Hub (Not included)

BPTA-RFCHUB

Do not over-tighten the thumb

screws. The springs should be

slightly compressed, with visible

gaps in the spring coils. Over-tight-

ening may result in poor contact

between the water block and CPU.

Use an appropriate amount

of Thermal Compound, - high-end

Bitspower cooling products are now

available at microcenter.com.

The CPU water block has a DRGB cable, which

can be connected to the DRGB extension

cable of the radiator fans.

Bitspower Fan and DRGB RF Remote Controller Hub

(Not included) are now available at microcenter.com

Titan One 3.0 is compatible with most ATX motherboards.

If not compatible, please contact Bitspower directly.

— 3 —

1

4

2

3

Use an appropriate amount

of Thermal Compound

CPU block

AM5 Installation

BP-CPUPDB-AMD5MS

C-5

1Thumb screw.................4 PCS

4Stud..........................4 PCS

2Spring .............................4 PCS

3Washer.....................4 PCS

— 4 —

II. Pre-Fill Installation

Step 1

Step 2

Hard tube BPTA-15ATFH16

When installing the hard pipe from the CPU

block to the water distribution reservoir,

You can move the hard pipe left and right to

get the proper installation length.

Loosen the screws.

Adjust the slider according to the CPU block position.

Adjust the hard pipe to the same level as the CPU Block inlet.

Before installing the water cooling parts for the

graphics card, please remove this part.

PUMP HEADER

FULL SPEED

AIO_PUMP

PUMP HEADER

PWM CONTROL

CPU_FAN

— 5 —

Upside downHead up

Hard Tube Motherboards

Mounting orientation

(CPU block position)

104x272 Head up Most ATX motherboards

104x255 Head up X670E AORUS MASTERGIGABYTE

— 6 —

Thumb screw

SPRING

CPU Block

1mm SPACER

M3x32mm SCREW

(for Intel)

1mm SPACER

Back Pad

3M Paste Pad

Metal Backplane

Thumb Nut

EX.

80

75

72

INTEL LGA 775

INTEL LGA 115X

INTEL LGA 1366

INTEL LGA 2011

INTEL LGA 2011-V3

INTEL LGA 2066

INTEL LGA 775

INTEL LGA 115X

INTEL LGA 1366

INTEL LGA 2011

INTEL LGA 2011-V3

INTEL LGA 2066

IN

OUT

A-2

DRGB PIN on Motherboard or other equipment.

 

Motherboard

Fan and DRGB RF Remote

Controller Hub (Not included)

BPTA-RFCHUB

The CPU water block has a DRGB cable, which

can be connected to the DRGB extension

cable of the radiator fans.

III. Intel Motherboards

Fin

Base screw

Base

Top

Intel Mounting Bracket

AMD Mounting Bracket

Installation

Do not over-tighten the thumb screws. The

springs should be slightly compressed, with

visible gaps in the spring coils. Over-tighten-

ing may result in poor contact between the

water block and CPU.

Bitspower Fan and DRGB RF Remote Controller Hub

(Not included) are now available at microcenter.com

Use an appropriate amount

of Thermal Compound, - high-end

Bitspower cooling products are now

available at microcenter.com.

Step 1

Step 2

— 7 —

4

1 2

3

Assembly steps

step 1

1

2

3

Installation(LGA 1700)

BPTA-MKCPUMS-1700(If you got this version, please refer to the following installation)

C-4

Backplate

— 8 —

step 3

step 2

4

2

— 9 —

1

Assembly steps

step 1

1

2

3

Installation(LGA 1700)

BPTA-MKCPUMS-1700-V2(If you got this version, please refer to the following installation)

C-4

Backplate

4

2

3

5

—

10

—

step 3

step 2

4

5

—

11

—

PUMP HEADER

FULL SPEED

AIO_PUMP

PUMP HEADER

PWM CONTROL

CPU_FAN

IV. Pre-Fill Installation

Step 1

Step 2

Hard tube BPTA-15ATFH16

When installing the hard pipe from the CPU

block to the water distribution reservoir,

You can move the hard pipe left and right to

get the proper installation length.

Titan One 3.0 is compatible with most ATX mother-

boards. If not compatible, please contact Bitspower

directly, thank you.

Loosen the screws.

Adjust the slider according to the CPU block position.

Adjust the hard pipe to the same level as the CPU Block inlet.

Before installing the water cooling parts for the

graphics card, please remove this part.

—

12

—

Upside downHead up

Hard Tube Motherboards

Mounting orientation

(CPU block position)

104x272 Head up Most ATX motherboards

104x272 Head up ROG MAXIMUS Z790 APEXASUS

104x255 Head up Z790 AORUS XTREMEGIGABYTE

104x272 Head up Z790 AEROGGIGABYTE

104x272 Upside down Z790A-SILVERBIOSTAR

104x255 Upside down Z790 TaichiASROCK

104x275 Head up PRO Z790-P WIFI DDR4MSI

In the event that the CPU Block is oriented higher than the

maximum default height of the Distribution Blocks' sliding CPU

Terminal, it is possible to rotate the face of the Terminal 180°

into its Upside Down position. This should allow the terminal to

match the height of the CPU Block.

—

13

—

BPTA-EFW

It is recommended to install the water-exhaust

fitting at the lowest point of the water cooling

system.

Step 1

Unscrew the top of the water-exhaust fitting.

AIO_PUMP

PUMP HEADER

PWM CONTROL

CPU_FAN

PUMP HEADER

FULL SPEED

AIO_PUMP

CPU_FAN

A Negative electrode -

B positive electrode +

C Speed signal

A B C D

Step 2

Replace with the water-exhaust part. When

screwing in the part, water will start to

discharge, it is recommended to connect

tubing beforehand to control the water outflow.

Pump Spec.

Rated voltage：12V DC

Power consumption：8.4W

Maximum flow：460±15%L/h

Noise：≦24dBA

PWM：Yes

MTBF：≦15,000 hours

Warranty：2 years

Water filling hole

90% full

V. Filling and Draining

Notice : Do not turn on the pump if the reservoir is empty.

Only Bitspower Coolant, purified water, or distilled water should be

used for the consumer's liquid-cooling fluid. If the consumer choos-

es different liquid-cooling fluids, the resulting impurities may cause

peeling of the coating on some of the hardware, water channel

block-age by built-up residue, improper operation of the water

pump, water tank tube breakage, and O-ring deformation leading to

leakage. Any issues related to the use of inappropriate liquid-cooling

fluid will be the responsibility of the consumer.

In order to make the internal circulation of the liquid-cooling system

cleaner and avoid the pump stuck by the precipitate, we advise you

torinse the liquid-cooling system with distilled water several times

until theexcluded water is clean.

Suggest using the normal mode of the case when

filling the water.

When draining, suggest using the reverse mode

of the case.

Pour the coolant into the reservoir via the water filling

hole. Once the reservoir is 90% full, turn on the power

supply for the pump to run and let the air exit the loop.

Turn off the power supply when the reservoir is near

empty. Repeat until all the air has exited the loop.

C-2

Before installing the water

cooling parts for the graphics

card, please remove this part.

Before adding a radiator, please remove

the whole acrylic plate and fittings.

—

14

—

Notice

Before filling with fluid, please make sure all the components are installed correctly. To prevent any leakage

which may damage the PC components, please perform a 24-hour leaking test with only the pump connected

to the power supply.

Bitspower reserves the right to change the product design and interpretations. These are subject to change

without notice. Product colors and accessories are based on the actual product.

When using leak Detector on water cooling loop, in order to avoid product damage due to excessive pressure,

the input pressure should not exceed 0.5kg/cm2 (Bar). If the product is damaged due to excessive pressure, it will

be the fault of the customer. DO NOT use the Leak Detector when there is water in the loop orthe pump is

running.

Bitspower mandates the use ofdistilled water, purifiedwater, orBitspowerPellucidCoolant as the liquid-cooling

fluid. The consumer may also add Bitspower Dye to Pellucid Coolant for their color preference. Please do not

add any biocide by yourself. If the consumer chooses different liquid-cooling fluid, the resulting impurities may

cause peeling off the coating on some of the hardware, water channels blockage by built-up residue, improper

operation of the water pump, water tank tube breakage, and O-rings deformation or loss sealing leading to

leakage. Any issues related to the use of inappropriate liquid-cooling fluid will be the responsibility of the

consumer.

Do not turn on the pump if the reservoir is empty.

About PSU

Please go to the website or scan the QR CODE to download the manual.

www.fsplifestyle.com/en/product/HYDROGPRO1000W_GEN5.html

Lista de componentes

..1 piezas

Soporte de montaj e Intel

— 1 —

Bitspower se reserva el derecho de modificar el diseño y las interpretaciones

del producto. Estos están sujetos a cambios sin previo aviso. Los colores del

producto y los accesorios se basan en el producto real.

Spanish

TITAN ONE EVO_3.0 Guía de instalación

BPTA-O11DEVO_A3.0-WH

Bloque de refrigeración líquida para CPU

A

B-1 B-2

A-1

A-2

A-3

.....1 piezas

BPTA-CPUMS-V2-SKA

A-1

A-2

..........1 set

Conjunto de placa base

A-3

Equipamiento

B

...........2 piezas

BPTA-DOTFH1622

B-1

...............2 piezas

BPTA-15ATFH16

B-2

Accesorio

C

....................6 piezas

Tubos rígidos

C-1

................1 piezas

Tubo de drenaje

C-2

A

B

C

Juego de bloques para CPU

C-3

BP-CPUPDB-AMD5MS

C-5

Tubos rígidos

C-1

Tubo de drenaje

C-2

V3

La variación permitida en la longitud del tubo es de ±2 mm

272

104

:16

La variación permitida en la longitud del tubo es de ±2 mm

275

104

:16

La variación permitida en la longitud del tubo es de ±2 mm

255

104

:16

BPTA-MKCPUMS-1700 or

BPTA-MKCPUMS-1700-V2

C-4

Tornillo de mariposa

MUELLE

Tuerca de mariposa

Separador de 1 mm

Tornillo M3×32 mm

SC6-32M3

Arandela de copa de nailon

..............4 piezas

..4 piezas

.............................4 piezas

...............4 piezas

..............8 piezas

..............4 piezas

................................4 piezas

Consulte las tablas de las páginas 5 y 12

para conocer la compatibilidad de los tubos

rígidos y la placa base.

EX.

I. Placas base para AMD

— 2 —

Tornillo M3×32 mm

(para Intel)

SEPARADOR de 1mm

Almohadilla trasera

Almohadilla adhesiva 3M

Placa base metálica

Tornillo de mariposa

MUELLE

Bloque para CPU

SEPARADOR de 1mm

Tornillo de mariposa

Bloque para CPU

SC6-32M3

(para AMD AM4)

Arandela de copa

de nailon

(para AMD AM4)

Placa base para

AMD original

MUELLE

SEPARADOR de 1mm

Tuerca de mariposa

96

90

48

54

AMD SOCKET AM4

AMD SOCKET AM3 / AM3+

AMD SOCKET AM2 / AM2+

AMD SOCKET FM1 / FM2+

AMD SOCKET 939 / 754 / 940

AMD SOCKET AM4

AMD SOCKET AM3 / AM3+

AMD SOCKET AM2 / AM2+

AMD SOCKET FM1 / FM2+

Instalación AM4 + Legado

Led DRGB

DENTRO

FUERA

PIN DRGB en  la placa base u  otro equipo.

 

Placa base

Ventilador y remoto DRGB RF

Controlador (no incluido)

BPTA-RFCHUB

No apriete demasiado los tornillos

de mariposa. Los muelles deben

estar ligeramente comprimidos y

contener espacios visibles en las

espirales. Un apriete excesivo puede

provocar un contacto deficiente

entre el bloque de refrigeración

líquida y la CPU.

Utilice una cantidad adecuada de

compuesto térmico. Los productos

de refrigeración de Bitspower de

gama alta ya están disponibles en

microcenter.com.

El bloque de refrigeración líquida para CPU tiene

un cable DRGB, que se puede conectar al

cable de extensión DRGB de los

ventiladores del radiador..

El ventilador Bitspower y el controlador remoto DRGB RF

(no incluido) ya están disponibles en microcenter.com

Titan One 3.0 es compatible con la mayoría de placas

base ATX. Si no fuera compatible, póngase en contacto

directamente con Bitspower.

— 3 —

1

4

2

3

Utilice una cantidad adecuada

de compuesto térmico

Bloque para CPU

AM5 Instalación

BP-CPUPDB-AMD5MS

C-5

1Tornillo de mariposa ...4 piezas

4Taco......................4 piezas

2MUELLE ..........................4 piezas

3Arandela...............4 piezas

— 4 —

II. Instalación previa al llenado

Paso 1

Paso 2

Tubos rígidos BPTA-15ATFH16

Al instalar el tubo rígido desde el bloque de la

CPU hasta el depósito de distribución de agua,

puede mover el tubo rígido a izquierda y

derecha para obtener la longitud de instalación

adecuada.

Afloje los tornillos.

Ajuste el regulador de acuerdo con la posición del bloque de

la CPU.

Ajuste el tubo rígido al mismo nivel que la entrada del

bloque de la CPU.

Antes de instalar las piezas de refrigeración líquida para la

tarjeta gráfica, retire esta pieza.

VELOCIDAD TOTAL

AIO_PUMP

CABEZAL DE LA BOMBA

CONTROL

PWM

CPU_FAN

— 5 —

En caso de que el bloque de la CPU esté orientado a una altura

superior a la altura máxima predeterminada del terminal

deslizante de la CPU de los bloques de distribución, es posible

girar la parte frontal del terminal 180° a su posición invertida.

Esto debería permitir que el terminal coincida con la altura del

bloque de la CPU.

Upside downHacia arriba

Tubos rígidos Placa bases

Orientación de montaje

(posición del bloque de la CPU)

104x272 Hacia arriba La mayoría de las placas base ATX

104x255 Hacia arriba X670E AORUS MASTERGIGABYTE

— 6 —

Tornillo de mariposa

MUELLE

Bloque para CPU

Separador de 1 mm

Tornillo M3×32 mm

(for Intel)

Separador de 1 mm

Almohadilla trasera

Almohadilla adhesiva 3M

Placa base metálica

Tuerca de mariposa

EX.

80

75

72

INTEL LGA 775

INTEL LGA 115X

INTEL LGA 1366

INTEL LGA 2011

INTEL LGA 2011-V3

INTEL LGA 2066

INTEL LGA 775

INTEL LGA 115X

INTEL LGA 1366

INTEL LGA 2011

INTEL LGA 2011-V3

INTEL LGA 2066

DENTRO

FUERA

A-2

El bloque de refrigeración líquida para CPU

tiene un cable DRGB, que se puede conectar

al cable de extensión DRGB de los

ventiladores del radiador.

Titan One 3.0 es compatible con la mayoría de placas base ATX.

Si no fuera compatible, póngase en contacto directamente con

Bitspower.

III. Placas base Intel

Aleta

Tornillo de la base

Base

Parte superior

Soporte de montaje Intel

Soporte de montaje AMD

Instalación

El ventilador Bitspower y el controlador remoto DRGB RF

(no incluido) ya están disponibles en microcenter.com

Utilice una cantidad adecuada de compuesto

térmico. Los productos de refrigeración de

Bitspower de gama alta ya están disponibles

en microcenter.com.

Paso 1

Paso 2

PIN DRGB en  la placa base u  other equipment.

 

Placa base

Ventilador y remoto DRGB RF

Controlador (no incluido)

BPTA-RFCHUB

No apriete demasiado los tornillos de mari-

posa. Los muelles deben estar ligeramente

comprimidos y contener espacios visibles en

las espirales. Un apriete excesivo puede

provocar un contacto deficiente

entre el bloque de refrigeración líquida y la

CPU.

ページが読み込まれています...

Bitspower BPTA-O11DEVO_A3.0-BK インストールガイド

このマニュアルも適しています

Bitspower BPTA-O11DEVO_A3.0-BK インストールガイド

他の言語で

関連論文

その他のドキュメント