Bitspower BPTA-O11DEVO_A3.0-BK インストールガイド

タイプ
インストールガイド

このマニュアルも適しています

Parts List
............1 pc
Intel Mounting Bracket
1
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
English
TITAN ONE EVO_3.0 Installation Guide
BPTA-O11DEVO_A3.0-WH
CPU Water Block
A
B-1 B-2
A-1
A-2
A-3
..........1 pc
BPTA-CPUMS-V2-SKA
A-1
A-2
...............1 set
Backplane assembly
A-3
Fittings
B
.................2 pcs
BPTA-DOTFH1622
B-1
....................2 pcs
BPTA-15ATFH16
B-2
Accessory
C
................................6 pcs
Hard tube
C-1
..............................1 pc
Drain Tube
C-2
A
B
C
CPU set
C-3
BP-CPUPDB-AMD5MS
C-5
Hard Tube
C-1
Drain Tube
C-2
V3
The allowable variance in tube length is ± 2mm
272
104
:16
The allowable variance in tube length is ± 2mm
275
104
:16
The allowable variance in tube length is ± 2mm
255
104
:16
BPTA-MKCPUMS-1700 or
BPTA-MKCPUMS-1700-V2
C-4
Thumb screw
SPRING
Thumb nut
1mm Spacer
M3x32mm Screw
SC6-32M3
Nylon cup washer
.................4 pcs
.................4 pcs
.................4 pcs
...........4 pcs
..................8 pcs
.....................4 pcs
.........................4 pcs
Please refer to the tables on pages 5 and 12
for Hard Tubes+Motherboard compatibility.
EX.
I. AMD Motherboard system
2
M3x32mm SCREW
(for Intel)
1mm SPACER
Back Pad
3M Paste Pad
Metal Backplane
Thumb screw
SPRING
CPU Block
1mm SPACER
Thumb screw
CPU Block
SC6-32M3
(for AMD AM4)
Nylon cup washer
(for AMD AM4)
Original
backplane
SPRING
1mm SPACER
Thumb Nut
96
90
48
54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
Installation
DRGB LED
IN
OUT
DRGB PIN on Motherboard or other equipment.
 
Motherboard
Fan and DRGB RF Remote
Controller Hub (Not included)
BPTA-RFCHUB
Do not over-tighten the thumb
screws. The springs should be
slightly compressed, with visible
gaps in the spring coils. Over-tight-
ening may result in poor contact
between the water block and CPU.
Use an appropriate amount
of Thermal Compound, - high-end
Bitspower cooling products are now
available at microcenter.com.
The CPU water block has a DRGB cable, which
can be connected to the DRGB extension
cable of the radiator fans.
Bitspower Fan and DRGB RF Remote Controller Hub
(Not included) are now available at microcenter.com
Titan One 3.0 is compatible with most ATX motherboards.
If not compatible, please contact Bitspower directly.
3
1
4
2
3
Use an appropriate amount
of Thermal Compound
CPU block
AM5 Installation
BP-CPUPDB-AMD5MS
C-5
1Thumb screw.................4 PCS
4Stud..........................4 PCS
2Spring .............................4 PCS
3Washer.....................4 PCS
4
II. Pre-Fill Installation
Step 1
Step 2
Hard tube BPTA-15ATFH16
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
Before installing the water cooling parts for the
graphics card, please remove this part.
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
5
Upside downHead up
Hard Tube Motherboards
Mounting orientation
(CPU block position)
104x272 Head up Most ATX motherboards
104x255 Head up X670E AORUS MASTERGIGABYTE
6
Thumb screw
SPRING
CPU Block
1mm SPACER
M3x32mm SCREW
(for Intel)
1mm SPACER
Back Pad
3M Paste Pad
Metal Backplane
Thumb Nut
EX.
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
IN
OUT
A-2
DRGB PIN on Motherboard or other equipment.
 
Motherboard
Fan and DRGB RF Remote
Controller Hub (Not included)
BPTA-RFCHUB
The CPU water block has a DRGB cable, which
can be connected to the DRGB extension
cable of the radiator fans.
III. Intel Motherboards
Fin
Base screw
Base
Top
Intel Mounting Bracket
AMD Mounting Bracket
Installation
Do not over-tighten the thumb screws. The
springs should be slightly compressed, with
visible gaps in the spring coils. Over-tighten-
ing may result in poor contact between the
water block and CPU.
Bitspower Fan and DRGB RF Remote Controller Hub
(Not included) are now available at microcenter.com
Use an appropriate amount
of Thermal Compound, - high-end
Bitspower cooling products are now
available at microcenter.com.
Step 1
Step 2
7
4
1 2
3
step 1
1
2
3
Installation(LGA 1700)
BPTA-MKCPUMS-1700(If you got this version, please refer to the following installation)
C-4
Backplate
8
step 3
step 2
4
2
9
1
step 1
1
2
3
Installation(LGA 1700)
BPTA-MKCPUMS-1700-V2(If you got this version, please refer to the following installation)
C-4
Backplate
4
2
3
5
10
step 3
step 2
4
5
11
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
IV. Pre-Fill Installation
Step 1
Step 2
Hard tube BPTA-15ATFH16
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
Titan One 3.0 is compatible with most ATX mother-
boards. If not compatible, please contact Bitspower
directly, thank you.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
Before installing the water cooling parts for the
graphics card, please remove this part.
12
Upside downHead up
Hard Tube Motherboards
Mounting orientation
(CPU block position)
104x272 Head up Most ATX motherboards
104x272 Head up ROG MAXIMUS Z790 APEXASUS
104x255 Head up Z790 AORUS XTREMEGIGABYTE
104x272 Head up Z790 AEROGGIGABYTE
104x272 Upside down Z790A-SILVERBIOSTAR
104x255 Upside down Z790 TaichiASROCK
104x275 Head up PRO Z790-P WIFI DDR4MSI
In the event that the CPU Block is oriented higher than the
maximum default height of the Distribution Blocks' sliding CPU
Terminal, it is possible to rotate the face of the Terminal 180°
into its Upside Down position. This should allow the terminal to
match the height of the CPU Block.
13
BPTA-EFW
It is recommended to install the water-exhaust
fitting at the lowest point of the water cooling
system.
Step 1
Unscrew the top of the water-exhaust fitting.
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
PUMP HEADER
FULL SPEED
AIO_PUMP
CPU_FAN
A Negative electrode -
B positive electrode +
C Speed signal
A B C D
Step 2
Replace with the water-exhaust part. When
screwing in the part, water will start to
discharge, it is recommended to connect
tubing beforehand to control the water outflow.
Pump Spec.
Rated voltage:12V DC
Power consumption:8.4W
Maximum flow:460±15%L/h
Noise:≦24dBA
PWM:Yes
MTBF:≦15,000 hours
Warranty:2 years
Water filling hole
90% full
V. Filling and Draining
Notice : Do not turn on the pump if the reservoir is empty.
Only Bitspower Coolant, purified water, or distilled water should be
used for the consumer's liquid-cooling fluid. If the consumer choos-
es different liquid-cooling fluids, the resulting impurities may cause
peeling of the coating on some of the hardware, water channel
block-age by built-up residue, improper operation of the water
pump, water tank tube breakage, and O-ring deformation leading to
leakage. Any issues related to the use of inappropriate liquid-cooling
fluid will be the responsibility of the consumer.
In order to make the internal circulation of the liquid-cooling system
cleaner and avoid the pump stuck by the precipitate, we advise you
torinse the liquid-cooling system with distilled water several times
until theexcluded water is clean.
Suggest using the normal mode of the case when
filling the water.
When draining, suggest using the reverse mode
of the case.
Pour the coolant into the reservoir via the water filling
hole. Once the reservoir is 90% full, turn on the power
supply for the pump to run and let the air exit the loop.
Turn off the power supply when the reservoir is near
empty. Repeat until all the air has exited the loop.
C-2
Before installing the water
cooling parts for the graphics
card, please remove this part.
Before adding a radiator, please remove
the whole acrylic plate and fittings.
14
Notice
Before filling with fluid, please make sure all the components are installed correctly. To prevent any leakage
which may damage the PC components, please perform a 24-hour leaking test with only the pump connected
to the power supply.
Bitspower reserves the right to change the product design and interpretations. These are subject to change
without notice. Product colors and accessories are based on the actual product.
When using leak Detector on water cooling loop, in order to avoid product damage due to excessive pressure,
the input pressure should not exceed 0.5kg/cm2 (Bar). If the product is damaged due to excessive pressure, it will
be the fault of the customer. DO NOT use the Leak Detector when there is water in the loop orthe pump is
running.
Bitspower mandates the use ofdistilled water, purifiedwater, orBitspowerPellucidCoolant as the liquid-cooling
fluid. The consumer may also add Bitspower Dye to Pellucid Coolant for their color preference. Please do not
add any biocide by yourself. If the consumer chooses different liquid-cooling fluid, the resulting impurities may
cause peeling off the coating on some of the hardware, water channels blockage by built-up residue, improper
operation of the water pump, water tank tube breakage, and O-rings deformation or loss sealing leading to
leakage. Any issues related to the use of inappropriate liquid-cooling fluid will be the responsibility of the
consumer.
Do not turn on the pump if the reservoir is empty.
About PSU
Please go to the website or scan the QR CODE to download the manual.
www.fsplifestyle.com/en/product/HYDROGPRO1000W_GEN5.html
Lista de componentes
..1 piezas
Soporte de montaj e Intel
1
Bitspower se reserva el derecho de modificar el diseño y las interpretaciones
del producto. Estos están sujetos a cambios sin previo aviso. Los colores del
producto y los accesorios se basan en el producto real.
Spanish
TITAN ONE EVO_3.0 Guía de instalación
BPTA-O11DEVO_A3.0-WH
Bloque de refrigeración líquida para CPU
A
B-1 B-2
A-1
A-2
A-3
.....1 piezas
BPTA-CPUMS-V2-SKA
A-1
A-2
..........1 set
Conjunto de placa base
A-3
Equipamiento
B
...........2 piezas
BPTA-DOTFH1622
B-1
...............2 piezas
BPTA-15ATFH16
B-2
Accesorio
C
....................6 piezas
Tubos rígidos
C-1
................1 piezas
Tubo de drenaje
C-2
A
B
C
Juego de bloques para CPU
C-3
BP-CPUPDB-AMD5MS
C-5
Tubos rígidos
C-1
Tubo de drenaje
C-2
V3
La variación permitida en la longitud del tubo es de ±2 mm
272
104
:16
La variación permitida en la longitud del tubo es de ±2 mm
275
104
:16
La variación permitida en la longitud del tubo es de ±2 mm
255
104
:16
BPTA-MKCPUMS-1700 or
BPTA-MKCPUMS-1700-V2
C-4
Tornillo de mariposa
MUELLE
Tuerca de mariposa
Separador de 1 mm
Tornillo M3×32 mm
SC6-32M3
Arandela de copa de nailon
..............4 piezas
..4 piezas
.............................4 piezas
...............4 piezas
..............8 piezas
..............4 piezas
................................4 piezas
Consulte las tablas de las páginas 5 y 12
para conocer la compatibilidad de los tubos
rígidos y la placa base.
EX.
I. Placas base para AMD
2
Tornillo M3×32 mm
(para Intel)
SEPARADOR de 1mm
Almohadilla trasera
Almohadilla adhesiva 3M
Placa base metálica
Tornillo de mariposa
MUELLE
Bloque para CPU
SEPARADOR de 1mm
Tornillo de mariposa
Bloque para CPU
SC6-32M3
(para AMD AM4)
Arandela de copa
de nailon
(para AMD AM4)
Placa base para
AMD original
MUELLE
SEPARADOR de 1mm
Tuerca de mariposa
96
90
48
54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
Instalación AM4 + Legado
Led DRGB
DENTRO
FUERA
PIN DRGB en la placa base u otro equipo.
 
Placa base
Ventilador y remoto DRGB RF
Controlador (no incluido)
BPTA-RFCHUB
No apriete demasiado los tornillos
de mariposa. Los muelles deben
estar ligeramente comprimidos y
contener espacios visibles en las
espirales. Un apriete excesivo puede
provocar un contacto deficiente
entre el bloque de refrigeración
líquida y la CPU.
Utilice una cantidad adecuada de
compuesto térmico. Los productos
de refrigeración de Bitspower de
gama alta ya están disponibles en
microcenter.com.
El bloque de refrigeración líquida para CPU tiene
un cable DRGB, que se puede conectar al
cable de extensión DRGB de los
ventiladores del radiador..
El ventilador Bitspower y el controlador remoto DRGB RF
(no incluido) ya están disponibles en microcenter.com
Titan One 3.0 es compatible con la mayoría de placas
base ATX. Si no fuera compatible, póngase en contacto
directamente con Bitspower.
3
1
4
2
3
Utilice una cantidad adecuada
de compuesto térmico
Bloque para CPU
AM5 Instalación
BP-CPUPDB-AMD5MS
C-5
1Tornillo de mariposa ...4 piezas
4Taco......................4 piezas
2MUELLE ..........................4 piezas
3Arandela...............4 piezas
4
II. Instalación previa al llenado
Paso 1
Paso 2
Tubos rígidos BPTA-15ATFH16
Al instalar el tubo rígido desde el bloque de la
CPU hasta el depósito de distribución de agua,
puede mover el tubo rígido a izquierda y
derecha para obtener la longitud de instalación
adecuada.
Afloje los tornillos.
Ajuste el regulador de acuerdo con la posición del bloque de
la CPU.
Ajuste el tubo rígido al mismo nivel que la entrada del
bloque de la CPU.
Antes de instalar las piezas de refrigeración líquida para la
tarjeta gráfica, retire esta pieza.
VELOCIDAD TOTAL
AIO_PUMP
CABEZAL DE LA BOMBA
CABEZAL DE LA BOMBA
CONTROL
PWM
CPU_FAN
5
En caso de que el bloque de la CPU esté orientado a una altura
superior a la altura máxima predeterminada del terminal
deslizante de la CPU de los bloques de distribución, es posible
girar la parte frontal del terminal 180° a su posición invertida.
Esto debería permitir que el terminal coincida con la altura del
bloque de la CPU.
Upside downHacia arriba
Tubos rígidos Placa bases
Orientación de montaje
(posición del bloque de la CPU)
104x272 Hacia arriba La mayoría de las placas base ATX
104x255 Hacia arriba X670E AORUS MASTERGIGABYTE
6
Tornillo de mariposa
MUELLE
Bloque para CPU
Separador de 1 mm
Tornillo M3×32 mm
(for Intel)
Separador de 1 mm
Almohadilla trasera
Almohadilla adhesiva 3M
Placa base metálica
Tuerca de mariposa
EX.
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
DENTRO
FUERA
A-2
El bloque de refrigeración líquida para CPU
tiene un cable DRGB, que se puede conectar
al cable de extensión DRGB de los
ventiladores del radiador.
Titan One 3.0 es compatible con la mayoría de placas base ATX.
Si no fuera compatible, póngase en contacto directamente con
Bitspower.
III. Placas base Intel
Aleta
Tornillo de la base
Base
Parte superior
Soporte de montaje Intel
Soporte de montaje AMD
Instalación
El ventilador Bitspower y el controlador remoto DRGB RF
(no incluido) ya están disponibles en microcenter.com
Utilice una cantidad adecuada de compuesto
térmico. Los productos de refrigeración de
Bitspower de gama alta ya están disponibles
en microcenter.com.
Paso 1
Paso 2
PIN DRGB en la placa base u other equipment.
 
Placa base
Ventilador y remoto DRGB RF
Controlador (no incluido)
BPTA-RFCHUB
No apriete demasiado los tornillos de mari-
posa. Los muelles deben estar ligeramente
comprimidos y contener espacios visibles en
las espirales. Un apriete excesivo puede
provocar un contacto deficiente
entre el bloque de refrigeración líquida y la
CPU.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Bitspower BPTA-O11DEVO_A3.0-BK インストールガイド

タイプ
インストールガイド
このマニュアルも適しています