AHD Digital Video Recorder
Quick Start
Guide
201511 104 108 116 A3
DVR104
DVR108
DVR116
1
English
1 Product Overview
Front Panel
The 4CH / 8CH AHD DVR front panel includes:
1. Power/ Alarm: Power indicator turns on when AHD DVR turns on. Alarm indicator blinks when the system alarm is
detected.
2. Network: Network indicator turns on when AHD DVR network access is connected.
3.
Record: Rec indicator turns on when AHD DVR is recording.
4.
USB Port: USB2.0 port for connecting devices, such as USB mouse or USB ash drive.
Packing Content
The package of 4CH / 8CH AHD DVR contains the following items:
- AHD DVR x 1 - Power adapter x 1
- Quick Install Paper x 1 - HDD mounting bracket x 4 pcs
- SATA connection cable x 2 - Screws for HDD mounting bracket (M3x4) x 10 pcs
- Screws for mounting hard drive (6
#
x6) x 10 pcs - User manual/Quick Install/CMS disc x 1
- USB mouse x 1
The package of 16CH AHD DVR contains the following items:
- AHD DVR x 1 - Power adapter x 1
- Quick Install Paper x1 - HDD mounting bracket x 4 pcs
- SATA connection cable x 4 - Screws for HDD mounting bracket (M3x3) x 10 pcs
- Screws for mounting hard drive (6
#
x6) x 20 pcs - User manual/Quick Install/CMS disc x 1
- USB mouse x 1 - Alarm terminal block x 4
The 16CH AHD DVR front panel includes:
1.
Record: Rec indicator turns on when AHD DVR is recording.
2.
Network: Network indicator turns on when AHD DVR network access is connected.
3.
Power/ Alarm: Power indicator turns on when AHD DVR turns on. Alarm indicator turns on when system alarm is
detected.
4. USB Port: USB2.0 port for connecting devices, such as USB mouse or USB ash drive.
2
English
Rear Panel
The 4CH AHD DVR rear panel:
The 8CH AHD DVR rear panel:
1. Antenna: Reserved for connecting to Zigbee device.
2. Video In: Connect Analog or AHD cameras’ video output to the AHD DVR video input connectors.
3. CVBS Out: Connect a CVBS Monitor to the CVBS output connector for 8CH/16CH AHD DVR only.
4. Audio In: Connect the microphone or camera audio output to the audio input connectors.
5. VGA: Connect a VGA monitor to the VGA output connector.
6. Network: For RJ-45 network connection.
7. Power: Plug the DV12V power source into the power socket.
8. Alarm In: Connect up to 4 alarm inputs to the alarm input connectors.
Alarm Out: N.C or N.O type alarm signal out.
9. Audio Out: Connect a speaker or other audio output device to the audio output connector.
10. HDMI: Connect a HDMI monitor to the HDMI output connector.
11. USB: USB 2.0 port for connecting devices, such as USB mouse or USB ash drive.
12. RS485: Connect a Pan/Tilt/Zoom camera to the RS485 port.
3
English
The 16CH AHD DVR rear panel includes:
1. Antenna: Reserved for connecting to Zigbee device.
2. CVBS Out: Connect a CVBS Monitor to the CVBS output connector for 8CH/16CH AHD DVR only.
3. Audio In: Connect the microphone or camera audio output to the audio input connectors.
4. Video In: Connect Analog or AHD cameras’ video output to the AHD DVR video input connectors.
5. ESATA: For connecting to external SATA HDD or disk array.
6. Alarm Out: N.C or N.O type alarm signal out.
7. Alarm In: Connect up to 16 alarm inputs to the alarm input connectors.
8. RS485: Connect a Pan/Tilt/Zoom camera to the RS485 port.
9. VGA: Connect a VGA monitor to the VGA output connector.
10. Network: For RJ-45 network connection.
11. Power: Plug the DV12V power source into the power socket.
12. Audio Out: Connect a speaker or other audio output device to the audio output connector.
13. HDMI: Connect a HDMI monitor to the HDMI output connector.
14. USB: USB 2.0 port for connecting devices, such as USB mouse or USB ash drive.
4
English
2
Installation
Hard Disk Installation
Follow the steps to install or replace the HDDs in
4CH / 8CH AHD DVR.
Step1. Take out the screws on the back panel and two sided as shown in the pictures.
Step2. Slide open the top cover.
Step3. Use the HDD mounting screws attached in the accessory pack to x the mounting brackets to the hard drive. Fix the
hard drive to the screw holes indicated as in the below pictures to make sure the hard drive is well installed for mounting to
the chassis.
5
English
Step4. Connect SATA & Power wire to HDD and put it on right position of the case. Use the HDD mounting screws attached in
the accessory pack to x the hard drive with bracket rmly on to the chassis.
Step 5. Connect the SATA cables to the SATA connectors on the main board. Please refer to the below for the hard drive port
numbers and connect the HDD accordingly. The DVR will recognize the hard drives according to the SATA port numbers for
the disk management.
4CH AHD DVR 8CH AHD DVR
6
English
Follow the steps to install or replace the HDDs in 16CH AHD DVR.
Step1. Take out the screws on the back panel and two sided as shown in the pictures.
Step2. Slide open the top cover.
Step3. Fix the HDD on to the HDD mounting bracket and x the screws on to the screw holes as indicated in the diagram.
Each set of HDD brackets can mount 2 HDDs.
7
English
Step4. Use the HDD mounting screws attached in the accessory pack to x the mounting brackets to the hard drive.
Step5. Connect SATA & Power wire to HDD and put it on right position of the case. Use the HDD mounting screws attached in
the accessory pack to x the hard drive with bracket rmly on to the chassis.
16CH AHD DVR
8
1
4 CH/8 CH AHD DVR
1.
/ AHD DVR
2.
AHD DVR
3.
AHD DVR Rec ( )
4.
USB USB USB USB 2.0
4 CH/8 CH AHD DVR
- AHD DVR x 1 - x 1
- x 1 - x 4
- SATA x 2 - (M3x4) x 10
- (6
#
x6) x 10 - / /CMS x 1
- USB x 1
16 CH AHD DVR
- AHD DVR x 1 - x 1
- x 1 - x 4
- SATA x 4 - (M3x3) x 10
- (6
#
x6) x 20 - / /CMS x 1
- USB x 1 - x 4
16 CH AHD DVR
1.
AHD DVR Rec ( )
2.
AHD DVR
3.
/ AHD DVR
4.
USB USB USB USB 2.0
9
4 CH AHD DVR :
8 CH AHD DVR :
1.
Zigbee
2.
AHD AHD DVR
3.
CVBS CVBS 8 CH/16 CH AHD DVR CVBS
4.
5.
VGAVGA VGA
6.
RJ-45
7.
DV 12 V
8.
4
N.C ( ) N.O ( )
9.
10.
HDMIHDMI HDMI
11.
USBUSB USB USB 2.0
12.
RS485 / / RS485
10
16 CH AHD DVR
1.
Zigbee
2.
CVBS CVBS 8 CH/16 CH AHD DVR CVBS
3.
4.
AHD AHD DVR
5.
ESATA SATA
6.
N.C ( ) N.O ( )
7.
16
8.
RS485 / / RS485
9.
VGAVGA VGA
10.
RJ-45
11.
DV 12 V
12.
13.
HDMIHDMI HDMI
14.
USBUSB USB USB
11
2
4 CH/8 CH AHD DVR
1
2
3
12
4SATA
5SATA SATA
DVR SATA
4CH AHD DVR 8CH AHD DVR
SATA
SATA
2
SATA
HDD1 HDD2
2
SATA HDD1
HDD2
13
16 CH AHD DVR
1
2
3
1 2
14
4
5SATA
16CH AHD DVR
SATA
SATA
4
SATA HDD1
HDD2HDD3 HDD4
15
简体中文
1 产品概述
前面板
4CH / 8CH AHD DVR 前面板上指示灯和端口定义如下：
1.
电源 / 报警：AHD DVR 开启后，电源指示灯点亮。当系统中检测到报警信号时，报警指示灯闪烁。
2.
网络：AHD DVR 网络访问连接后，网络指示灯点亮。
3.
录像：AHD DVR 录像时，Rec 指示灯点亮。
4.
USB 端口 : USB2.0 端口用于连接 USB 鼠标或 USB 闪存驱动器等。
标准配备
4CH / 8CH AHD DVR 包装中包含以下物品：
- AHD DVR x 1 - 电源适配器 x 1
- 快速安装指南 x 1 - HDD 安装支架 x 4 pcs
- SATA 连接线 x 2 - HDD 支架安装螺丝 (M3x4) x 10 pcs
- 硬盘安装螺丝 (6
#
x6) x 10 pcs - 光盘（使用手册 / 快速安装指南 /CMS ）x 1
- USB 鼠标 x 1
16CH AHD DVR 包装中包含以下物品 :
- AHD DVR x 1 - 电源适配器 x 1
- 快速安装指南 x 1 - HDD 安装支架 x 4 pcs
- SATA 连接线 x 4 - HDD 支架安装螺丝 (M3x3) x 10 pcs
- 硬盘安装螺丝 (6
#
x6) x 20 pcs - 光盘（使用手册 / 快速安装指南 /CMS ）x 1
- USB 鼠标 x 1 - 报警接线端子 x 4
16CH AHD DVR 前面板上指示灯和端口定义如下：
1.
录像：AHD DVR 录像时，Rec 指示灯点亮。
2.
网络：AHD DVR 网络访问连接后，网络指示灯点亮。
3.
电源 / 报警：AHD DVR 开启后，电源指示灯点亮。当系统中检测到报警信号时，报警指示灯点亮。
4.
USB 端口 : USB2.0 端口用于连接 USB 鼠标或 USB 闪存驱动器等。
16
简体中文
后面板
4CH AHD DVR 后面板上各端口定义如下：
8CH AHD DVR 后面板上各端口定义如下：
1.
天线： 预留连接 Zigbee 设备。
2.
视频输入：接模拟或 AHD 摄像机的视频输出。
3.
CVBS 输出：接 CVBS 显示器，仅 8CH/16CH AHD DVR 支持。
4.
音频输入：接麦克风或摄像机音频输出。
5.
VGA：接 VGA 显示器。
6.
网络：RJ-45 网络接口。
7.
电源：接 DV12V 电源。
8.
报警输入：最多可连接 4 路报警输入。
报警输出：常闭 (N.C) 或常开 (N.O) 类型的报警信号输出。
9.
音频输出：接扬声器或其他音频输出设备。
10.
HDMI：接 HDMI 显示器。
11.
USB：USB2.0 端口用于连接 USB 鼠标或 USB 闪存驱动器等。
12.
RS485：接 PTZ 摄像机。
17
简体中文
16CH AHD DVR 后面板上个端口定义如下：
1.
天线： 预留连接 Zigbee 设备。
2.
CVBS 输出：接 CVBS 显示器，仅 8CH/16CH AHD DVR 支持。
3.
音频输入：接麦克风或摄像机音频输出。
4.
视频输入：接模拟或 AHD 摄像机的视频输出。
5.
ESATA：接外部 SATA HDD 或磁盘阵列。
6.
报警输出：常闭 (N.C) 或常开 (N.O) 类型的报警信号输出。
7.
报警输入：最多可连接 16 路报警输入。
8.
RS485：接 PTZ 摄像机。
9.
VGA：接 VGA 显示器。
10.
网络：RJ-45 网络接口。
11.
电源：接 DV12V 电源。
12.
音频输出：接扬声器或其他音频输出设备。
13.
HDMI：接 HDMI 显示器。
14.
USB：USB2.0 端口用于连接 USB 鼠标或 USB 闪存驱动器等。
18
简体中文
2
安装
硬盘安装
请根据以下步骤安装或更换 4CH / 8CH AHD DVR 中的硬盘。
第一步：拧下硬盘录像机后面板和侧面上的螺丝，如下图所示。
第二步：侧滑打开上盖。
第三步：用 HDD 安装螺丝（配件包中附带）将硬盘安装支架固定到硬盘 上，螺丝孔位置如下图所示，请确保硬盘已
安装固定好。
19
简体中文
第四步：将 SATA & 电源线连接到 HDD 上，并将所有线材放置到合适位置；然后用 HDD 安装螺丝（配件包中附带）
将硬盘和支架固定底盘上。
第五步：将 SATA 线另一端接到主板上的 SATA 端口 ，请参考下图了解对应型号 DVR 硬盘端口数量，安装连接硬盘。
DVR 会根据 SATA 端口数量识别硬盘，管理所连接的硬盘。
4CH AHD DVR 8CH AHD DVR
SATA 线此接头连接 HDD SATA 线此接头连接 DVR 主板
此型号 DVR 最多可连接 2 个内置硬盘，请将 HDD
连接到 SATA 端口 HDD1 和 HDD2。
此型号 DVR 最多可连接 2 个内置硬盘，请将 HDD 连接到
SATA 端口 HDD1 和 HDD2。
ページを読み込んでいます...
ページを読み込んでいます...
/