ETS 2 取扱説明書

Multilingual Version

English

日本語

400a_400b_500_500a_operation_V1.2

BOX IP CAMERA SERIES

OPERATION GUIDE

Please read instructions thoroughly before operation and retain it for future reference.

IMPORTANT SAFEGUARD

All lead-free products offered by the company comply with the requirements of the

European law on the Restriction of Hazardous Substances (RoHS) directive, which means

our manufacture processes and products are strictly “lead-free” and without the hazardous

substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product

must be collected separately at the product end-of-life. This applies to your product and

any peripherals marked with this symbol. Do not dispose of these products as unsorted

municipal waste. Contact your local dealer for procedures for recycling this equipment.

This apparatus is manufactured to comply with the radio interference requirements.

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

 FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

 All external cables connecting to this basic unit must be shielded.

For cables connecting to PCMCIA cards, see the option manual or installation instructions.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device mat not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

Trademark Acknowledgements

IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

Android is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.

Microsoft, Windows & Internet Explorer are registered trademarks of Microsoft Corporation in the United

States and/or other countries.

Disclaimer

We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume

any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. The content of

this manual is subject to change without notice.

This product doesn’t have a standby / off mode.

MPEG4 Licensing

THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE

PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN

COMPLIANCE WITH THE MPEG4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING

MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND

NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY

MPEG LA TO PROVIDE MPEG4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY

OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL

AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE

HTTP://WWW.MPEGLA.COM.

GPL Licensing

This product contains codes which are developed by Third-Party-Companies and which

are subject to the GNU General Public License (“GPL”) or the GNU Lesser Public License

(“LGPL”).

The GPL Code used in this product is released without warranty and is subject to the

copyright of the corresponding author.

Further source codes which are subject to the GPL-licenses are available upon request.

We are pleased to provide our modifications to the Linux Kernel, as well as a few new

commands, and some tools to get you into the code. The codes are provided on the FTP

site, and please download them from the following site or you can refer to your distributor:

Model 1: http://download.dvrtw.com.tw/GPL/IPCAM/S-Seriers/linux.tar.gz

Model 2 & 3: http://download.dvrtw.com.tw/GPL/IPCAM/F-Seriers/linux.tar.gz

TABLE OF CONTENTS

1. OVERVIEW......................................................................................................................................... 1

1.1 Product Features....................................................................................................................................... 1

1.2 Package Content....................................................................................................................................... 1

1.3 Hardware Overview................................................................................................................................... 1

1.4 Rear Panel ................................................................................................................................................ 1

1.5 External I/O Port........................................................................................................................................ 2

1.6 Status Indicator.......................................................................................................................................... 2

1.7 Insert a Micro SD Card (For Model 2, 3 & 4 Only) .................................................................................... 3

2. CAMERA ACCESS WITH INTERNET EXPLORER............................................................................ 4

2.1 Camera Login............................................................................................................................................ 4

2.2 Control Panel Overview ............................................................................................................................ 4

2.3 Digital PTZ (DPTZ) Operations ................................................................................................................. 6

2.4 Event Record Search & Playback ............................................................................................................. 7

3. CAMERA CONFIGURATIONS............................................................................................................ 8

3.1 System configuration menu....................................................................................................................... 8

3.2 Network ..................................................................................................................................................... 9

3.2.1 Network ............................................................................................................................................................9

3.2.2 QoS ..................................................................................................................................................................9

3.2.3 DDNS .............................................................................................................................................................10

3.2.4 SNTP..............................................................................................................................................................10

3.2.5 FTP.................................................................................................................................................................10

3.2.6 MAIL ...............................................................................................................................................................10

3.2.7 SMS................................................................................................................................................................ 11

3.2.8 Filter ...............................................................................................................................................................12

3.2.9 UPnP / Bonjour...............................................................................................................................................12

3.2.10 RTP ..............................................................................................................................................................13

3.2.11 SNMP (For Model 3 & 4 only) ......................................................................................................................14

3.2.12 IEEE 802.1X* (For Model 3 & 4 only) ..........................................................................................................15

3.2.13 Network Share (For Model 3 & 4 only).........................................................................................................16

3.2.14 Network Failure Detection (For Model 3 & 4 only).......................................................................................16

3.3 Camera ................................................................................................................................................... 17

3.3.1 Camera...........................................................................................................................................................17

3.3.2 Video ..............................................................................................................................................................17

3.3.3 ROI (For Model 3 & 4 only) ............................................................................................................................18

3.3.4 Color...............................................................................................................................................................18

3.3.5 Audio ..............................................................................................................................................................18

3.3.6 Advanced........................................................................................................................................................19

3.3.7 Privacy Mask (For Model 3 & 4 only) .............................................................................................................20

3.4 VA (For Model 3 & 4 only) ....................................................................................................................... 20

3.4.1 TA ...................................................................................................................................................................20

3.4.2 DIS .................................................................................................................................................................21

3.5 Record..................................................................................................................................................... 21

3.5.1 Record............................................................................................................................................................21

3.5.2 Record Timer..................................................................................................................................................21

3.6 Storage.................................................................................................................................................... 22

3.6.1 Memory ..........................................................................................................................................................22

3.7 Trigger ..................................................................................................................................................... 22

3.7.1 Trigger ............................................................................................................................................................22

3.7.2 Snapshot ........................................................................................................................................................24

3.8 General ................................................................................................................................................... 24

3.8.1 General...........................................................................................................................................................24

3.8.2 Time................................................................................................................................................................25

3.8.3 Server Log......................................................................................................................................................25

3.8.4 Online .............................................................................................................................................................26

3.8.5 Account...........................................................................................................................................................26

3.8.6 Google Maps..................................................................................................................................................27

3.8.7 Maintenance...................................................................................................................................................27

APPENDIX 1 PRODUCT SPECIFICATIONS........................................................................................ 29

APPENDIX 2 BIT RATE TABLE FOR REFERENCE ............................................................................ 30

APPENDIX 3 Q&A ................................................................................................................................ 32

APPENDIX 4 RECORDING TIME TABLE ............................................................................................ 33

APPENDIX 5 MICRO SD CARD COMPATIBLE LIST........................................................................... 34

APPENDIX 6 API ID APPLICATION FOR SMS MESSAGING.............................................................. 35

APPENDIX 7 PREREQUISITES FOR NETWORK SHARE.................................................................. 37

A7.1 Check PC IP Address ........................................................................................................................... 37

A7.2 Create "Administrator" Account............................................................................................................. 37

A7.3 Share Folder ......................................................................................................................................... 38

1

1. OVERVIEW

1.1 Product Features

 Quick network setup with your iOS® / Android™ mobile device

 External alarm I/O device connection

-- For more accurate detection

-- Possible to enable active event notifications to your iOS® & Android™ mobile devices (Push Video) when used with Push

Video NVR series

 POE (Power-over-Ethernet) support to eliminate the use of power cables and reduce installation costs

 ONVIF standard supported to simplify system integration

 Microphone built-in for audio recording

 Remote Surveillance

-- Fully compatibility on iPhone & iPad, and Internet Explorer on Windows operating system

 (Model 3 & 4 only) WDR support to make everything still visible and clear in a scene where exists both bright and dark areas

 (Model 2, 3 & 4 only) Micro SD card support for video recording

 (Model 4 only) RS485 support for control

1.2 Package Content

□ IP camera □ I/O Terminal block

□ Wrench □ CD Manual (Optional)

□ Quick Setup

1.3 Hardware Overview

1.4 Rear Panel

Ethernet Connect your network cable.

DC12V IN Connect the supplied regulated power supply.

Reset With the power connected, press to reset all parameters, including the IP address to factory default

settings.

The camera will reboot after default reset. Please do not disconnect your camera during the reset

process.

2

External I/O Port An I/O terminal is supplied with the camera for external alarm device connection.

“D/N IN” is used to connect to an external illuminator.

For connection details, please refer to “1.5 External I/O Port” at page 2.

Micro SD This port is used to insert a micro SD card to video recording.

1.5 External I/O Port

This camera supports external I/O device connection, and a I/O terminal block is supplied with this camera for

easy connection.

Below shows which input on the I/O terminal block you should use for wiring when you want to connect an

external device to this camera.

4-pin I/O Terminal Block 3-pin I/O Terminal Block

Alarm Out Connection Example

1.6 Status Indicator

 For Model 1

ICON

LAN connection status Internet connection status

System Status

During powering on Always on Always off

Blinking (on 250 ms, off 250 ms) Always off

Reset default 

Blinking (on 250 ms, off 250 ms) Blinking (on 250 ms, off 250 ms)

Upgrade  

Connection Status

LAN connected Always on --

Blinking (on 100 ms, off 500 ms) --

LAN disconnected 

Internet connected -- Always on

Blinking (on 100 ms, off 500 ms)

Internet disconnected -- 

Micro SD Card Status

Micro SD card error Keep current status for 20 sec  Blinking for 3 sec  Return to current status

Status during Network Setup

-- Blinking

(on 5 sec, off 0.5 sec, on 0.5 sec, off 0.5 sec, on 5 sec)

Port forwarding required

-- 

* LED blinking frequency -



LED on /



LED off

3

 For Model 2 & 4

ICON

LAN connection status Internet connection status

System Status

During powering on Always on Always off

LAN blinking (on 250 ms, off 250 ms), Internet off, and then LAN off, Internet blinking (on 250 ms, off 250 ms)

Reset default 

Blinking (on 250 ms, off 250 ms) Blinking (on 250 ms, off 250 ms)

Upgrade  

Connection Status

LAN connected Always on --

Blinking (on 100 ms, off 500 ms) --

LAN disconnected 

Internet connected -- Always on

Blinking (on 100 ms, off 500 ms)

Internet disconnected -- 

Micro SD Card Status

Micro SD card error Keep current status for 20 sec  Blinking for 3 sec  Return to current status

Status during Network Setup

-- Blinking

(on 5 sec, off 0.5 sec, on 0.5 sec, off 0.5 sec, on 5 sec)

Port forwarding required

-- 

* LED blinking frequency -



LED on /



LED off

1.7 Insert a Micro SD Card (For Model 2, 3 & 4 Only)

For local video recording, a micro SD card slot can be found on the side of the camera.

Note: Before inserting a micro SD card, make sure you’ve copied all important data saved in the card

(if any) to other storage media, or the data will be removed after inserting it to the camera.

Check the indication above to ensure where your micro SD card is, and insert it to your camera.

Note: It’s recommended to insert or remove the micro SD card with power disconnected, or the

camera will reboot.

Note: For the compatible list of the micro SD card, please refer to “APPENDIX 5 MICRO SD CARD

COMPATIBLE LIST” at page 34.

4

2. CAMERA ACCESS WITH INTERNET EXPLORER

This camera can be accessed via Microsoft Internet Explorer, and iOS / Android mobile devices with our

self-developed program “EagleEyes” installed depending on different using situations.

Note: For details about accessing this camera via iOS / Android mobile devices, please refer to

http://www.eagleeyescctv.com.

Before using the camera, make sure you have configured the network settings, and the network connection is fine.

 For network configurations, please refer to “Advanced Network Setup” downloadable from

www.surveillance-download.com/user/m500.swf.

2.1 Camera Login

Step1: Open your web browser, and key in http://ipaddress:portnum in the URL address box.

For example, for the IP address 60.121.46.236 and port No. 888, please key in ”http://60.121.46.236:888” into

the URL address box, and press “Enter”.

Step2: In the login page, key in the user name and password, and enter the security code from the image below if any.

Then, click “LOGIN”.

Step3: The wizard is then started.

‧ To skip the wizard and directly access the camera live view, click “Close”.

‧ To directly access the camera live view without starting the wizard for the login next time, check “Do not start wizard at login”.

Note: If you’re prompted to install “VLC player”, “Software” or “H264 Streaming Viewer”, please agree

to proceed the installation. Or, you might not be able to see the live view properly.

Step5: When the login is successful, the live view is shown.

2.2 Control Panel Overview

Note: The buttons available depend on the camera model you have, and the user level used to log in.

5

Function Icon User Level Description

Live

Supervisor / Power User

/ Normal User / Guest Switch to the live view page.

DPTZ

Supervisor / Power User

/ Normal User

Switch to the DPTZ configuration page.

For details, please refer to “2.3 Digital PTZ (DPTZ) Operations” at page 6.

Backup Supervisor / Power User Enter the event record list for video playback.

For details, please refer to “2.4 Event Record Search & Playback’ at page 7.

Config. Supervisor

Switch to the system configuration page, and the functions available for

“Supervisor” and “Power User” are different.

For details, please refer to “3.1 System configuration menu” at page 8.

Select the image player from the drop-down list: Live player* -- Supervisor / Power User

/ Normal User / Guest  ActiveX

 QuickTime

QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime

installed in your operating system before selecting “QuickTime”. When it is

selected, you will be promoted to enter the user name and password to access

the camera.

 VLC

Select the image player from the drop-down list: Media Type* -- Supervisor / Power User

/ Normal User / Guest  H.264 / MPEG-4 / Motion JPEG

 QuickTime

QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime

installed in your operating system before selecting “QuickTime”. When it is

selected, you will be promoted to enter the user name and password to access

the camera.

 VLC

Quality --

Supervisor / Power User

/ Normal User

Click & drag the slider to select the video quality:

Basic / Normal / High / Best.

Select the image resolution from the drop list:

 1920 x 1080  1280 x 720

Video Profile* -- Supervisor / Power User

/ Normal User

 720 x 480  352 x 240

Select the image resolution from the drop list:

 HD1080P: 1920 x 1080  HD720P: 1280 x 720

Video Resolution* -- Supervisor / Power User

/ Normal User

 VGA: 640 x 480  QVGA: 320 x 240

Snapshot

Supervisor / Power User

/ Normal User

Click to take a snapshot of the current view on a new window. Right click

on the picture and re-save it to the location you want.

Full Screen

Supervisor / Power User

/ Normal User

Click to display the image in full screen.

To exit the full screen mode, press “Esc” on your keyboard.

Audio On / Off /

Supervisor / Power User

/ Normal User Click to switch the audio-in on / off.

Manual Alarm Out

Supervisor / Power User

/ Normal User

Click to force the connected alarm-out device to work. For example, when

your alarm device is a buzzer, click this button and your buzzer will start to

sound even if there’s no alarm event.

Microphone* / Supervisor Click to switch the audio-out on / off.

Live View Size: Supervisor / Power User

/ Normal User

Normal Size* The current live view size is the same as the selected resolution.

Fit to screen* The selected resolution is resized to fit into the current live view size.

This icon doesn’t work when the selected resolution is VGA or QVGA.

Scale*

Click and hold the movable square on the left bottom corner of the live view

to move

This icon appears only when the selected resolution is larger than the current live

view size.

Double Size

The QVGA resolution is resized to fit into the current live view size.

This icon appears only when the selected resolution is QVGA (320 x 240) or CIF

(352 x 240).

Focus Assist

Supervisor / Power User

/ Normal User

Click to help you determine whether the image clearness is adjusted well

when you're adjusting your camera focus. Two values will be calculated

and shown as “XX / YY”.

 YY is the best focus value for your current camera view

 XX is your current focus value

When XX is closer to YY, the clearer and sharper images you’ll get for your

camera view.

Zoom-in / out /

Supervisor / Power User

/ Normal User Click to zoom in / out the current image.

Max. Zoom-in / out /

Supervisor / Power User

/ Normal User

Click to zoom in the image to the largest / zoom out the image to its

original size.

DPTZ*

Supervisor / Power User

/ Normal User Click to enable digital PTZ functions with zoom-in ratio up to 16X.

* Selected Models Only

6

2.3 Digital PTZ (DPTZ) Operations

This camera series has PTZ capability, i.e. digital PTZ (hereafter called “DPTZ”), for wide area monitoring.

Click “DPTZ” on the top left corner to show the DPTZ control panel.

 For Model 4 & 5

FUNCTION ICON DESCRIPTION

Moving panel -- When is selected, the moving control panel will be shown to move the picture after zoom-in is

performed.

Take snapshots Click to take a snapshot of the current view on a new window. Right click on the picture and re-save it

to the location you want.

Zoom in / out / Click once to enlarge the picture by 1X, and click once to restore the zoom ratio by 1X.

Max. zoom in / out / Click once to enlarge the picture to the max zoom ratio by 16X, and click once to restore the

picture ratio to 1X.

 For Model 1 & 2

FUNCTION ICON DESCRIPTION

Resolution -- Select the video resolution for the DPTZ function. Only “VGA” and “QVGA” are available.

Take snapshots Click to take a snapshot of the current view on a new window. Right click on the picture and re-save it to the

location you want.

Audio On / Off / Click to switch the audio-in on / off.

7

FUNCTION ICON DESCRIPTION

Alarm Out Click to force the connected alarm-out device to work. For example, when your alarm device is a buzzer, click

this button and your buzzer will start to sound even if there’s no alarm event.

Microphone / Click to switch the audio-out on / off.

2.4 Event Record Search & Playback

This camera can only save a few recordings.

Note: To save more recorded data, it’s recommended to use this camera with the compatible NVR.

/ Previous / Next Hour Click to jump to the next / previous time interval in an hour, for example, 11:00 ~ 12:00 or 14:00

~ 15:00, and start playing the earliest event video clip recorded during this whole hour.

Fast Forward Increase the speed for fast forward. Click to get 2X, 4X, 8X & 16X speed forward eventually.

Fast Rewind Increase the speed for fast rewind. Click to get 2X, 4X, 8X & 16X speed rewind eventually.

Play Click to play the current video clip.

Pause Click to pause the video playback.

Stop Click to stop the video playback.

Step In the pause mode, click to get one frame forward.

Audio Click to mute the playback if necessary, and click again to restore.

Download

Click to download the current video clip to the specified path in your PC.

The downloaded video can only be opened by our own video player. Please go to “General”

→

“Maintenance” to

download the video player, or get the player from the CD supplied with the sales package.

8

3. CAMERA CONFIGURATIONS

Users can further configure this camera by accessing via Internet Explorer.

3.1 System configuration menu

Click “Config.” to enter the configuration page.

Note: You need to be “Supervisor” to enter the system configuration page. If you’re not a “Supervisor”,

please re-log into the camera with the correct user name and password.

The functions are categorized into six menus: Network, Camera, Record Timer, Storage, Trigger and General.

 For details about “Network”, please refer to “3.2 Network” at page 9.

 For details about “Camera”, please refer to 3.3 Camera” at page 14.

 For details about “VA”, please refer to “3.4 VA” at page 20.

 For details about “Record”, please refer to “3.5 Record” at page 21.

 For details about “Storage”, please refer to “3.6 Storage”’ at page 22.

 For details about “Trigger”, please refer to “3.7 Trigger” at page 22.

 For details about “General”, please refer to “3.8 General” at page 24.

Main Menu

Sub-Menu Reference

Network Network Configure network settings.

QoS Limit the data flow for live streaming.

DDNS Enter DDNS information when the network type is PPPOE or DHCP.

SNTP Synchronize your camera time with the networked computer systems.

FTP Enter the FTP information for event notifications when “FTP” is chosen in “Trigger” →

“Trigger”.

Mail Enter Email information for event notifications when “Email” is chosen in “Trigger” → “Trigger”.

SMS Enter text messaging information for SMS notifications when “SMS” is chosen in “Trigger” →

“Trigger”.

Filter Choose to permit or block the IP address(es) which can access this camera.

UpnP

*Suitable for Windows-based operating system.

Allow this camera to be detected among devices within the same network area for easy and

quick usage.

Bonjour

*Suitable for Apple Mac-based operating system.

Allow this camera to be detected among devices within the same network area for easy and

quick usage.

RTP Set the parameters for video data transmission when you’re using multimedia other than web

browsers and Video Viewer for remote access.

SNMP* Configure SNMP to remotely manage network devices.

IEEE 802.1X* The settings here enable the camera to access a network protected by 802.1X/EAPOL

(Extensible Authentication Protocol Over LAN).

Network Share* Assign a location in the LAN environment to save the snapshot of events when “Network

Share” is chosen in “Trigger” → “Snapshot”.

Network Failure Detection* Configure this camera to check the network connection of other device periodically, and send

notifications via Email or FTP for disconnection events.

Camera Camera

1. Set the camera title.

2. Specify the display position of the camera title.

3. Specify where the snapshot files should be saved.

Video Adjust video-related settings in different video format.

ROI* Select a specific area to reinforce the image quality of that area.

Color Adjust the color performance.

Audio Adjust the audio volume of the built-in microphone.

Advanced Adjust the camera parameters if necessary.

Privacy Mask* Cover certain areas on the camera image.

9

3.2 Network

3.2.1 Network

You can set the network configuration of the camera depending on your network type.

For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m500.swf.

3.2.2 QoS

QoS, Quality of Service, is the ability to control the data flow for real-time streaming. This function is important if

your network bandwidth is insufficient and you have other devices to share the network bandwidth.

Check “QoS Enable”, and set the max. upload rate from 256 to 10240 kbps.

Main Menu

Sub-Menu Reference

VA* TA This function should be used with the mini-guard control switch for alarm system integration.

For details, please check with your distributor or installer.

DIS Enable this function to reduce blurring associated with the motion of a camera during

exposure.

Record Record Configure the record function.

Record Timer Schedule external alarm recording.

Storage Memory Check the current storage capacity and clear all recorded data when needed.

Trigger Trigger

1. Enable / disable motion and alarm detection.

2. Set the motion detection area.

3. Configure how the camera reacts for any event.

Snapshot Schedule the camera to take snapshots periodically or at a specific time, and send to E-Mail,

FTP and / or Network Share for backup. Time-lapse recording could also be configured here.

General General

1. Select the language of the web browser.

2. Check the MAC address of the camera.

3. Lock camera access after the specified time.

Time Set daylight saving time and the current time.

Server Log Check the system event logs.

Online Check the current online user(s).

Account 1. Create a new user account with different access privilege.

2. Modify or delete an existing user account.

Google Maps Allow you to know where the camera is.

Maintenance

1. Check the current firmware version and upgrade your camera.

2. Copy system configurations.

3. Reboot the camera.

4. Download the video player to play the recorded data.

10

3.2.3 DDNS

Select “On” when the selected network type in “Network” is “PPPOE” or “DHCP”.

For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m500.swf.

3.2.4 SNTP

SNTP (Simple Network Time Protocol) is used to synchronize your camera time with the networked computer

systems.

Function Description

GMT Once users choose the time zone, the camera will adjust the local area time of the system automatically.

NTP Server Simply use the default SNTP server (For example, tock.stdtime.gov.tw) or change to another server with which users are

familiar.

Sync. Period Select “Daily” to synchronize the camera time with the network time every day or “None” to turn off this function.

Sync Click and the camera will synchronize the time with the network time.

3.2.5 FTP

Enter the detailed FTP information and click “Save” to confirm. The information you set here will be applied

when “FTP” is selected in “Trigger” → “Trigger”.

3.2.6 MAIL

Enter the detailed e-mail information and click “Save” to confirm. The information you set here will be applied

when “Email” is selected in “Trigger” → “Trigger”.

11

Function Description

SMTP Server Enter the SMTP server address provided from your e-mail system supplier.

Port Enter the port number provided from your e-mail system supplier. If this column is left blank, the e-mail server will use

port 25 to send e-mails.

Mail From Enter the name of the sender.

SSL Encryption Select “Yes” if your e-mail server is using SSL encryption to protect your e-mail content from unauthorized access.

Verify Password Some mail servers are required to verify the password. Please enter the “user name” and “password”.

Subject Enter the subject for the E-Mail.

E-Mail Address List Add the e-mail address(s) of the assigned recipient(s).

Test When all information is entered, click “Test Mail” to try if the receipt.

3.2.7 SMS

Note: Before using this function, you need to apply an account and get an API ID from the mobile

messaging company, such as Clickatell and EVERY8D.

For details, please refer to “APPENDIX 6 API ID APPLICATION FOR SMS MESSAGING” at page 35.

Enter the detailed information needed for text messaging, and click “Save” to confirm. The information you set

here will be applied when “SMS” is selected in “General” → "Trigger".

Function Description

System The text messaging service provider is Clickatell.

User name / Password Enter the account user name and password you created in Clickatell.

API ID Enter the API ID you applied from Clickatell.

Recipient Click “Add” to enter the phone number, including the country code, to receive the text

message. Five sets of phone numbers are allowed.

Transfer Interval Set the interval time in minutes between two-message sending.

The options are 0, 15, 30 & 60.

Reset Counter Click to restart the text messaging, and the SMS will be sent after the specified time interval

since you click this button.

Message Enter the text content (up to 70 characters) you want to send with the text message.

Test To know whether your SMS setting is correct, click this button to immediately send a SMS to

your phone.

Note: This testing is not free and you will be charged for SMS sending base on your

local rate.

12

3.2.8 Filter

Choose to permit or block the IP address(es) which can access this camera, and click “Save” to confirm.

Function Description

 Filter Configuration

Error Count Set the maximum count for login failure. When the maximum count is reached, the IP address trying to access the

camera will be locked.

Error Lock Time Set the lock time in minutes when the maximum count of error login for an IP address is reached.

Echo Request Select “Non-Block” to allow other users to use the ping command to detect the IP address of your camera, or “Block” to

deny the ping command request.

 IP/MAC Filter Configuration

IP/MAC Filter Choose to enable or disable the filter function.

IP/MAC Filter Policy If “Enable” is selected, choose whether you want to permit (Allow) or block (Deny) the IP address list below.

 IP/MAC Filter Rules

Rule ‧ To add an item to the IP address list, key in the IP address in “Rule”, and click “Add”.

‧ To remove an existing item in the IP address list, click the item you want to remove, and click “Delete”.

3.2.9 UPnP / Bonjour

“UPnP” stands for “Universal Plug and Play”, which allows devices to connect seamlessly in the home and

corporate environments and simplify installation of computer components, and is only suitable for Microsoft

Windows-based operating system.

“Bonjour” functions the same as “UPnP”, but it’s only suitable for Apple Mac-based operating system.

 UPnP

 Bonjour

Check “Enable” to allow the camera to be detected among devices within the same network area, and set the

identification name of the camera in “Friendly name”.

When this function is activated, the other PC within the same domain as this camera will be able to search this

camera in:

 “Network Neighbor” with the identification name set in “Friendly name” for Windows-based PC, or

 “ ” (finder) or “Bookmark” with the identification name set in “Device Name” for Mac-based PC.

Double-click it to quickly open the web browser for camera access.

13

Port Mapping (Available only in UPnP)

This function can eliminate the need to additionally access the router for port forwarding.

For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m500.swf.

Note: Before using this function, make sure your router supports UPnP, and this function is enabled. If

not, please access your router additionally for port forwarding.

When “Port Mapping” is set to “Enable”, the system will automatically assign an IP address or port number for

you if no IP address or port number is entered.

Note: When the configurations are saved successfully, you’ll see a message indicating the IP address

and port number assigned to this camera.

3.2.10 RTP

The Real-time Transport Protocol (RTP) is an Internet protocol standard to manage the real-time transmission of

multimedia, such as VLC player.

The media player you want to use for remote access must support RTP transmission for this function to work

normally.

Note: When you’re about to end the remote access, please press the stop button on your media player

first, and then close the program. This is to ensure the server receives the stop command, and

also help to protect the server from redundant data transmission.

 For Model 3 & 4

Function Description

 Port Range

The port range used by RTP is limited, and preserving 100 ports between the start port and end port is necessary.

Start Port The range of the start port is 1024 ~ 65434.

End Port The range of the end port is 1124 ~ 65534.

 Video

Address and port for

video transmission

Set a specific address and port for multicast of profile 1 ~ 4.

The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.

The port for multicast must be an even number.

 Audio

Address and port for

audio transmission

Set a specific address and port for multicast of audio.

The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.

The port for multicast must be an even number.

14

 For Model 1 & 2

Function Description

 Port Range

The port range used by RTP is limited, and preserving 100 ports between the start port and end port is necessary.

Start Port The range of the start port is 1024 ~ 65434.

End Port The range of the end port is 1124 ~ 65534.

 Multicast

Address and port for

H264 / MPEG4 /

JPEG transmission

Set a specific address and port for multicast of each stream format (H264/ MPEG4/ JPEG).

The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.

The port for multicast must be an even number.

Address and port for

audio transmission

Set a specific address and port for multicast of audio.

The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.

The port for multicast must be an even number.

Time to Live (TTL) The range of Time to Live of the package is between 1 ~ 255. As soon as Time to Live of the

package is 0, it will be dropped.

3.2.11 SNMP (For Model 3 & 4 only)

SNMP, Simple Network Management Protocol, is used to facilitate the exchange of management information

between network-attached devices, and network administrators could use it to monitor those devices.

The SNMP consists of three basic components:

 Network-management systems (NMSs) to monitor and control the managed devices.

 Managed devices as network nodes to save all network and management information, such as routers, access

servers, switches, bridges, hubs, etc.

 Agents as network management software modules on managed devices to provide the status of managed devices

to NMSs.

Note: Before configuring SNMP settings, make sure your NMS is enabled first.

Enable SNMP V1 / V2C

Select “Yes” to enable this function, and enter the names of “Read community” and “Write community” based on

your NMS configurations.

ページが読み込まれています...

ETS 2 取扱説明書

このマニュアルも適しています

ETS 2 取扱説明書

他の言語で

その他のドキュメント