Sony KDL-50W800C リファレンスガイド

カテゴリー
液晶テレビ
タイプ
リファレンスガイド

このマニュアルも適しています

KDL-50W800C / 43W800C
Television
Reference Guide
GB
CT
2
GB
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Parts and Controls . . . . . . . . . . . . . . . . . . . 6
Controls and Indicators . . . . . . . . . . . . . . . . .6
Inputs and Outputs . . . . . . . . . . . . . . . . . . . . 7
Using Remote Control . . . . . . . . . . . . . . . . 8
Remote Control Parts Description. . . . . . . . . 8
Connecting the TV . . . . . . . . . . . . . . . . . . 10
Installing the TV to the Wall . . . . . . . . . . 12
Using your TV's Table-Top Stand as a
Wall-Mount Bracket . . . . . . . . . . . . . . . . . . . 12
Using an optional Wall-Mount Bracket . . . . 17
Troubleshooting. . . . . . . . . . . . . . . . . . . . 21
Troubles and Solutions . . . . . . . . . . . . . . . . 21
Specifications . . . . . . . . . . . . . . . . . . . . . . 22
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual thoroughly and
retain it for future reference.
Note
Before operating the TV, please read “Safety Information”
(page 2).
Instructions about “Installing the TV to the Wall” are included
within this TV’s instructions manual.
Images and illustrations used in Startup Guide and this manual
are for reference only and may differ from actual product
appearance.
Location of the identification label
Labels for the TV Model No. and Power Supply rating are located
on the rear of the TV.
Labels for the AC adapter Model No. and Serial No. are located on
the bottom of the AC adapter.
WARNING
Batteries must not be exposed to excessive heat such as
sunshine, fire or the like.
Installation/Set-up
Install and use the TV set in accordance with the instructions
below in order to avoid any risk of fire, electrical shock or damage
and/or injuries.
Installation
The TV set should be installed near an easily accessible AC
power outlet (mains socket).
Place the TV set on a stable, level surface to avoid it from falling
down and cause personal injury or damage to the TV.
Only qualified service personnel should carry out wall
installations.
For safety reasons, it is strongly recommended that you use
Sony accessories, including:
Wall-Mount Bracket (Supplied)
Wall-Mount Bracket SU-WL450
Be sure to use the screws supplied with the Wall-Mount Bracket
when attaching the Mounting Hooks (Stand)/Wall-Mount
Bracket to the TV set. The supplied screws are designed as
indicated by illustration when measured from the attaching
surface of the Mounting Hooks (Stand)/Wall-Mount Bracket.
The diameter and length of the screws differ depending on the
Wall-Mount Bracket model.
Use of screws other than those supplied may result in internal
damage to the TV set or cause it to fall, etc.
Wall-Mount Bracket (Supplied)
Wall-Mount Bracket SU-WL450
This television is designed for use in Hong Kong and ensured
the usage in Hong Kong only.
Safety Information
Screw (supplied with the
Wall-Mount Bracket)
Mounting Hook (Stand)
5 mm
Screw (supplied with the
Wall-Mount Bracket)
Wall-Mount Bracket
10-12 mm
3
GB
GB
Transporting
Before transporting the TV set, disconnect all cables.
Two or three people are needed to transport a large TV set.
When transporting the TV set by hand, hold it as shown below.
Do not put stress on the LCD panel and the frame around the
screen.
When transporting the TV set, do not subject it to jolts or
excessive vibration.
When transporting the TV set for repairs or when moving, pack
it using the original carton and packing material.
Ventilation
Never cover the ventilation holes or insert anything in the
cabinet.
Leave space around the TV set as shown below.
It is strongly recommended that you use a Sony Wall-Mount
Bracket in order to provide adequate air circulation.
Installed on the wall
Installed with stand
To ensure proper ventilation and prevent the collection of dirt or
dust:
Do not lay the TV set flat, install upside down, backwards, or
sideways.
Do not place the TV set on a shelf, rug, bed or in a closet.
Do not cover the TV set with a cloth, such as curtains, or items
such as newspapers, etc.
Do not install the TV set as shown below.
AC power cord (mains lead)
Handle the AC power cord (mains lead) and outlet (mains socket)
as follows in order to avoid any risk of fire, electrical shock or
damage and/or injuries:
Use only Sony supplied AC power cords (mains lead), not those
of other brands.
Insert the plug fully into the AC power outlet (mains socket).
Operate the TV set on a 220-240 V AC supply only.
When wiring cables, be sure to unplug the AC power cord
(mains lead) for your safety and take care not to catch your feet
on the cables.
Disconnect the AC power cord (mains lead) from the AC power
outlet (mains socket) before working on or moving the TV set.
Keep the AC power cord (mains lead) away from heat sources.
Unplug the AC power plug (mains plug) and clean it regularly. If
the plug is covered with dust and it picks up moisture, its
insulation may deteriorate, which could result in a fire.
Note
• Do not use the supplied AC power cord (mains lead) on any
other equipment.
• Do not pinch, bend, or twist the AC power cord (mains lead)
excessively. The core conductors may be exposed or broken.
• Do not modify the AC power cord (mains lead).
• Do not put anything heavy on the AC power cord (mains lead).
• Do not pull on the AC power cord (mains lead) itself when
disconnecting the AC power cord (mains lead).
• Do not connect too many appliances to the same AC power
outlet (mains socket).
• Do not use a poor fitting AC power outlet (mains socket).
NOTE ON AC ADAPTER
Warning
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
To prevent fire or shock hazard, do not place objects filled with
liquids, such as vases, on the apparatus.
Do not install this equipment in a confined space, such as a
bookshelf or similar unit.
• Please ensure that the AC power outlet (mains socket) is
installed near the equipment and shall be easily accessible.
• Be sure to use the supplied AC adapter and AC power cord
(mains lead). Otherwise it may cause a malfunction.
• Connect the AC adapter to an easily accessible AC power outlet
(mains socket).
Do not coil the AC power cord (mains lead)
around the AC adapter. The core wire may
be cut and/or it may cause a malfunction
of the TV.
• Do not touch the AC adapter with wet hands.
• If you notice an abnormality in the AC adapter, disconnect it
from the AC power outlet (mains socket) immediately.
• The set is not disconnected from the AC source as long as it is
connected to the AC power outlet (mains socket), even if the set
itself has been turned off.
• As the AC adapter will become warm when it is used for a long
time, you may feel hot when touching it by hand.
Prohibited Usage
Do not install/use the TV set in locations, environments or
situations such as those listed below, or the TV set may
malfunction and cause a fire, electrical shock, damage and/or
injuries.
Location:
Outdoors (in direct sunlight), at the seashore, on a ship or other
vessel, inside a vehicle, in medical institutions, unstable
locations, near water, rain, moisture or smoke.
If the TV is placed in the changing room of
a public bath or hot spring, the TV may be
damaged by airborne sulphur, etc.
• For best picture quality, do not expose the screen to direct
illumination or sunlight.
• Avoid moving the TV from a cold area to a warm area. Sudden
room temperature changes may cause moisture condensation.
This may cause the TV to show poor picture and/or poor colour.
Should this occur, allow moisture to evaporate completely
before powering the TV on.
Environment:
• Places that are hot, humid, or excessively dusty; where insects
may enter; where it might be exposed to mechanical vibration,
near flammable objects (candles, etc.). The TV set shall not be
exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the TV.
30 cm
10 cm
10 cm
10 cm
Leave at least this space around the set.
30 cm
10 cm
10 cm
Leave at least this space around the set.
6 cm
Air circulation is blocked.
Wall Wall
4
GB
Do not place the TV in a humid or dusty
space, or in a room with oily smoke or
steam (near cooking tables or
humidifiers). Fire, electric shock, or
warping may result.
• Do not install the TV in places subject to extreme temperature,
such as in direct sunlight, near a radiator or a heating vent. The
TV may overheat in such conditions which can cause
deformation of the enclosure and/or TV malfunction.
Situation:
Do not use when your hands are wet, with the cabinet removed,
or with attachments not recommended by the manufacturer.
Disconnect the TV set from AC power outlet (mains socket) and
antenna (aerial) during lightning storms.
• Do not install the TV so that it sticks out
into an open space. Injury or damage
from a person or object bumping into
the TV may result.
Broken pieces:
Do not throw anything at the TV set. The screen glass may break
by the impact and cause serious injury.
If the surface of the TV set cracks, do not touch it until you have
unplugged the AC power cord (mains lead). Otherwise electric
shock may result.
When not in use
• If you will not be using the TV set for several days, the TV set
should be disconnected from the AC power (mains) for
environmental and safety reasons.
• As the TV set is not disconnected from the AC power (mains)
when the TV set is just turned off, pull the plug from the AC
power outlet (mains socket) to disconnect the TV set
completely.
• However, some TV sets may have features that require the TV
set to be left in standby to work correctly.
For children
Do not allow children to climb on the TV set.
Keep small accessories out of the reach of children, so that they
are not mistakenly swallowed.
If the following problems occur...
Turn off the TV set and unplug the AC power cord (mains lead)
immediately if any of the following problems occur.
Ask your dealer or Sony service centre to have it checked by
qualified service personnel.
When:
AC power cord (mains lead) is damaged.
Poor fitting of AC power outlet (mains socket).
TV set is damaged by being dropped, hit or having something
thrown at it.
Any liquid or solid object falls through openings in the cabinet.
About LCD Monitor Temperature
When the LCD Monitor is used for an extended period, the panel
surrounds become warm. You may feel hot when touching there
by the hand.
WALL-MOUNT BRACKET
Below information shows the correct handling of the Wall-Mount
Bracket. Be sure to read this information thoroughly and use the
Wall-Mount Bracket correctly.
To Customers:
Be sure to observe the following precautions for safety to prevent
a serious injury through fire, electric shock, the product toppling
over, or the product dropping.
Be sure to subcontract the installation to licensed contractors
and keep small children away during installation.
Be sure to subcontract moving or dismounting of the TV to
licensed contractors.
• Do not remove screws, etc., after mounting the TV.
Do not make alterations to the parts of the Wall-Mount Bracket.
Do not mount any equipment other than the specified product.
Do not apply any load other than the TV on the Wall-Mount
Bracket.
Do not lean on or hang from the TV.
Do not handle the TV with excessive force during cleaning or
maintenance.
To Sony Dealers and Contractors:
The following instructions are for Sony dealers and contractors
only. Be sure to read safety precautions described below and pay
special attention to safety during the installation, maintenance
and checking of this product.
When handling or mounting the TV set, hold it on the sides. Do
not lift the TV by the Stand.
Do not install the Wall-Mount Bracket on
wall surfaces where the corners or the
sides of the TV are protruding away from
the wall surface.
Do not install the TV over or under an air
conditioner.
Be sure to install the Wall-Mount Bracket
securely to the wall following the
instructions in this instruction manual. If any
of the screws are loose or fall out, the Wall-
Mount Bracket may fall and cause injury or
property damage.
Be sure to use the supplied screws and
attachment parts properly following the
instructions given in this instruction manual.
If you use substitute items, the TV may fall
and cause bodily injury to someone or damage to the TV.
Be sure to assemble the bracket properly following the
instructed procedure explained in this instruction manual.
Be sure to tighten the screws securely in the designated
position.
Be careful not to subject the TV to shock during installation.
Be sure to install the TV on a wall that is both perpendicular and
flat.
After proper installation of the TV, secure the cables properly.
Do not allow the AC power cord (mains
lead) or the connecting cables to be
pinched as the internal conductors may
become exposed and cause a short
circuit or an electrical break.
Stand Stand
5
GB
GB
Viewing the TV
Some people may experience discomfort (such as eye strain,
fatigue, or nausea) while watching 3D video images or playing
stereoscopic 3D games. Sony recommends that all viewers take
regular breaks while watching 3D video images or playing
stereoscopic 3D games. The length and frequency of necessary
breaks will vary from person to person. You must decide what
works best. If you experience any discomfort, you should stop
watching the 3D video images or playing stereoscopic 3D
games until the discomfort ends; consult a doctor if you believe
necessary. You should also review (i) the instruction manual of
any other device or media used with this television and (ii) our
website (http://www.sony-asia.com/support) for the latest
information. The vision of young children (especially those
under six years old) is still under development. Consult your
doctor (such as a paediatrician or eye doctor) before allowing
young children to watch 3D video images or play stereoscopic
3D games. Adults should supervise young children to ensure
they follow the recommendations listed above.
Do not use, store, or leave the 3D Glasses or battery near a fire,
or in places with a high temperature, e.g., in direct sunlight, or
in sun-heated cars.
View the TV in moderate light, as viewing the TV in poor light or
during long period of time, strains your eyes.
When using headphones, adjust the volume so as to avoid
excessive levels, as hearing damage may result.
LCD Screen
Although the LCD screen is made with high-precision
technology and 99.99% or more of the pixels are effective, black
dots may appear or bright points of light (red, blue, or green)
may appear constantly on the LCD screen. This is a structural
property of the LCD screen and is not a malfunction.
Do not push or scratch the front filter, or place objects on top of
this TV set. The image may be uneven or the LCD screen may be
damaged.
If this TV set is used in a cold place, a smear may occur in the
picture or the picture may become dark. This does not indicate a
failure. These phenomena disappear as the temperature rises.
Ghosting may occur when still pictures are displayed
continuously. It may disappear after a few moments.
The screen and cabinet get warm when this TV set is in use. This
is not a malfunction.
The LCD screen contains a small amount of liquid crystal. Follow
your local ordinances and regulations for disposal.
Handling and cleaning the screen surface/
cabinet of the TV set
Be sure to unplug the AC power cord (mains lead) connected to
the TV set from AC power outlet (mains socket) before cleaning.
To avoid material degradation or screen coating degradation,
observe the following precautions.
To remove dust from the screen surface/cabinet, wipe gently
with a soft cloth. If dust is persistent, wipe with a soft cloth
slightly moistened with a diluted mild detergent solution.
Never spray water or detergent directly on
the TV set. It may drip to the bottom of the
screen or exterior parts and enter the TV set,
and may cause damage to the TV set.
Never use any type of abrasive pad, alkaline/acid cleaner,
scouring powder, or volatile solvent, such as alcohol, benzene,
thinner or insecticide. Using such materials or maintaining
prolonged contact with rubber or vinyl materials may result in
damage to the screen surface and cabinet material.
Periodic vacuuming of the ventilation openings is
recommended to ensure to proper ventilation.
When adjusting the angle of the TV set, move it slowly so as to
prevent the TV set from moving or slipping off from its table
stand.
Optional Equipment
Keep optional components or any equipment emitting
electromagnetic radiation away from the TV set. Otherwise
picture distortion and/or noisy sound may occur.
Wireless Function of the unit
• Do not operate this unit near medical equipment (pacemaker,
etc.), as malfunction of the medical equipment may result.
• Although this unit transmits/receives scrambled signals, be
careful of unauthorised interception. We cannot be responsible
for any trouble as a result.
Caution about handling the remote control
• Observe the correct polarity when inserting batteries.
• Do not use different types of batteries together or mix old and
new batteries.
• Dispose of batteries in an environmentally friendly way. Certain
regions may regulate the disposal of batteries. Please consult
your local authority.
• Handle the remote control with care. Do not drop or step on it,
or spill liquid of any kind onto it.
Do not place the remote control in a location near a heat source,
a place subject to direct sunlight, or a damp room.
WALL-MOUNT BRACKET
• If you use the TV installed on the Wall-Mount Bracket for a long
time, the wall behind or above the TV may become discoloured
or the wallpaper may come unglued, depending on the material
of the wall.
• If the Wall-Mount Bracket is removed after installing it on the
wall, the screw holes remain.
• Do not use the Wall-Mount Bracket in a place where it is
subjected to mechanical vibration.
Precautions
6
GB
Parts and Controls
Remote Control sensor* /
Light sensor*
/ Illumination LED
/
3D Sync Transmitter*
The Illumination LED lights up or blinks
according to the status of the TV.
•White
When turning on the TV/picture off
mode/software update, etc.
•Cyan
When connecting with a mobile device
wirelessly.
•Amber
Timer is set.
 (Power)
CH +/- (Channel)
+/- (Volume)
TV
Switch to a TV channel or input from other
applications.
 (Input select)
Display and select the input source.
* Do not place anything near the sensor.
Controls and Indicators
TV
̔
Ȫ
ȫ
Ȭ
ȭ
7
GB
GB
 VIDEO IN, / COMPONENT IN
For a composite connection:
Use VIDEO IN, and (L/R) of /
COMPONENT IN*.
For a component connection:
Use Y, PB, PR, and (L/R).
HDMI 3 AUDIO IN
For HDMI 3 analogue audio connection.
DIGITAL AUDIO OUT (OPTICAL)
 LAN
 CABLE/ANTENNA
Connect to your cable or antenna (aerial).
USB 1/2
Connecting a large USB device may
interfere with other connected devices
beside it.
When connecting a large USB device,
connect to the USB 1 socket.
HDMI IN 2/3/4
If the device has a DVI jack (socket),
connect it to HDMI IN 3 through a DVI -
HDMI adaptor interface (not supplied),
and connect the device's audio out jacks
(sockets) to HDMI 3 AUDIO IN.
If connecting a digital audio system that is
compatible with Audio Return Channel
(ARC) technology, use HDMI IN 4. If not, an
additional connection with DIGITAL AUDIO
OUT (OPTICAL) is necessary.
AUDIO OUT /
To listen to the TV's sound through the
connected equipment, press HOME. Select
[Settings] [Sound] [Headphone/
Audio Out] and then select the desired item.
HDMI IN 1/MHL
You can connect your MHL (Mobile High-
definition Link) device using an HD quality
MHL cable.
* When connecting mono equipment, connect to the L
(MONO) audio jack.
Inputs and Outputs
ȭ
ȯ
Ȱ
Ȫ ȫ
Ȭ
ȭ
ȩ
Ȯ
8
GB
Using Remote Control
/ (Input select/Text hold)
In TV mode: Display and select the input
source.
In Text mode: Hold the current page.
(TV standby)
Turn on or turn off the TV (standby mode).
DIGITAL/ANALOG
Switch between digital and analogue mode.
EXIT
Return to the previous screen or exit from
the menu. When an Interactive Application
service is available, press to exit from the
service.
Number buttons
(Twin picture/PIP)*
1
*
2
Display two pictures simultaneously.
(Text)
Display text information.
Colour buttons
Execute correspondent function at that time.
(Wide mode)
Change the screen format.
TV
Switch to a TV channel or input from other
applications.
HELP
Display Help Menu.
Remote Control Parts Description
Ȫ
ȩ
ȫ
Ȭ
ȭ
Ȯ
ȯ
9
GB
GB
ACTION MENU
Display a list of contextual functions.
/ (Info/Text reveal)
Display information.
GUIDE/ *
1
Display the digital programme guide.
BACK
Return to previous screen.
HOME
Display the TV Home Menu.
DISCOVER
Bring up the Content Bar to search for
content.
//// (Item select/Enter)
 +/– (Volume)
Adjust the volume.
(Jump)
Jump back and forth between two channels
or inputs. The TV alternates between the
current channel or input and the last
channel or input that was selected.
(Muting)
Mute the sound. Press again to restore the
sound.
PROG +/–//
In TV mode: Select the channel.
In Text mode: Select the next () or
previous () page.
AUDIO
Change the language for the programme
currently being viewed.
(Subtitle setting)
Turn subtitles on or off (when the feature is
available).
//////
Operate media contents on TV and
connected BRAVIA Sync-compatible device.
SYNC MENU
Display the BRAVIA Sync Menu.
FOOTBALL
Turn Live Football Mode on or off (when the
feature is available).
*1 The location, availability and function of remote
control button may vary depending on your country/
region/TV model.
*2 Twin Picture function will be available from July 2015.
You will receive Twin Picture function automatically
as a network software upgrade. Make sure your TV is
connected to the Internet. If you do not have a
network connection, you will be able to download
the software from the Sony support website using
your PC. For details on how to upgrade, please visit
the Sony support website.
10
GB
Connecting the TV
Note
When connecting the cable to the Cable/Antenna,
input finger tighten only, over-tightening the
connection can damage the TV.
To connect with an HDMI cable
To connect with component cables
To connect with AV composite cables
To HDMI OUT
< 21 mm
< 12 mm
To AUDIO OUT
To COMPONENT
OUT (P
R/PB/Y)
To VIDEO OUT
11
GB
GB
SD HD
Picture Quality
•AV composite cable
Antenna (aerial) cable
Component cable HDMI cable
Standard definition (SD) videos have picture signals with a
vertical resolution of 480 (NTSC) or 576 (PAL/SECAM) lines.
High definition (HD) videos have picture signals
with a vertical resolution of 720 or 1,080 lines.
12
GB
Installing the TV to the Wall
Your TV’s Table-Top Stand will be used as a part of the Wall-Mount Bracket.
Note
See page 2 (Safety Information) and page 5 (Precautions) on WALL-MOUNT BRACKET before carrying out Wall-Mount
Bracket installation.
If the Table-Top Stand is attached to the TV, detach the Table-Top Stand beforehand.
Place the TV with its screen facing down on a flat and stable surface covered with a thick and soft cloth that is larger
than the TV, when securing the Stand or when removing the Table-Top Stand from the TV to prevent damaging the
surface of the LCD display.
Once the Stand Necks are detached from the Stand, be sure to keep the Stand Necks and screws in a safe place.
When attaching the Table-Top Stand again, be sure to fasten the screws (previously removed) to the original holes
on the rear of the TV.
To detach the Table-Top Stand from the TV
Using your TV's Table-Top Stand as a Wall-Mount Bracket
To Customers
Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony
dealers or licensed contractors and pay special attention to safety during the installation. Sony is not liable
for any damages or injury caused by mishandling or improper installation, or installing any other than the
specified product. Your Statutory Rights (if any) are not affected.
To Sony Dealers and Contractors
Sufficient expertise is required for installing this product. Be sure to read this instruction manual thoroughly
to do the installation work safely. Sony is not liable for any damages or injury caused by mishandling or
improper installation.
Soft cloth
Stand Necks
Stand
13
GB
GB
Installing the Brackets on the wall
1 Prepare necessary items.
Wall-Mount Bracket accessories
Stand B
Screws for Wall-Mount Base (8 mm in diameter, not supplied)
2 Make sure that the wall has enough space for the TV and is capable of supporting a
weight of at least four times that of the TV.
Refer to the following table on installing the TV to the wall. See page 22-24 (Specifications)
for the TV’s weight.
Screen centre point
14
GB
Unit: mm
Note
Figures in the table may differ slightly depending on the installation.
3 Make a mark on the Paper Template A that indicates the centre of the screen for your TV.
4 Tape the Paper Template A to the wall and drill holes according to the numbering on the
Paper Template A using an electric drill.
5 Remove the Paper Template A off from the wall.
6 Attach the Wall-Mount Base B to the wall correctly using the screws (8 mm in diameter,
not supplied).
Model Name
KDL-
Display dimensions Screen centre dimension Length for mounting
50W800C 1,116 654 215 552 87
43W800C 962 565 253 544 87
150
200
250
300
Scale on Paper Template A
Mark for
KDL-50W800C
Mark for
KDL-43W800C
50
0
50
1
100
150
200
250
300
2
3
4
1, 2, 3, 4
Wall
A
15
GB
GB
Preparing for the installation of the TV
1 Insert the pin (on the Stand Protector C) into the hole on the Stand B, then fold up the
Stand Protector C. Confirm the Stand Protector C is firmly latched to the Stand B.
2 Attach the Stand B to the TV using the supplied screws D. Attach the Spacers E to the
holes indicated by the triangle marks
f
.
Note
You cannot use some of the terminals on the rear of the TV when using this mounting style.
ɹ
C
Pin
E
B
D
Soft cloth
Soft cloth
16
GB
Installing the TV on the wall
1 Make sure to connect and bundle the cables before installing the TV on the wall.
2 Install the TV on the wall. Then, confirm the Stand Protector C is firmly latched into the
Wall-Mount Base B and the Spacers E touch the wall.
Dimensions of the hole positions on the wall
Provide the following information to the licensed contractors if necessary.
Use screws (8 mm in diameter, not supplied) to install the Wall-Mount Base B on the wall.
Be sure to use the supplied Paper Template A that shows the actual position of Wall-Mount Base B
for easy installation.
B
C
B
B
E
Wall
Wall
170 mm
37 mm
B
17
GB
GB
This TV’s instruction manual only shows the steps on preparing the installation of the TV before
installing to the wall.
To Customers:
For product protection and safety reasons, Sony strongly recommends that installation of your
TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and examination of
this product.
Use the Wall-Mount Bracket SU-WL450 (not supplied) to install the TV to the wall.
When installing the Wall-Mount Bracket, also refer to the Operating Instructions and Installation Guide
supplied with the Wall-Mount Bracket.
Note
Be sure to store the removed screws in a safe place, keeping them away from children.
See page 2 (Safety Information) and page 5 (Precautions) on WALL-MOUNT BRACKET before carrying out Wall-
Mount Bracket installation.
If the Table-Top Stand is attached to the TV, detach the Table-Top Stand beforehand.
Place the TV with its screen facing down on a flat and stable surface covered with a thick and soft cloth that is
larger than the TV, when securing the Stand or when removing the Table-Top Stand from the TV to prevent
damaging the surface of the LCD display.
When attaching the Table-Top Stand again, please refer Startup Guide to fasten the screws (previously removed)
to the original holes on the rear of the TV.
Using an optional Wall-Mount Bracket
Sufficient expertise is required for installing this product, especially to determine the strength of the wall for
withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers
or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for
any damage or injury caused by mishandling or improper installation.
Soft cloth
Stand Necks
Stand
18
GB
SU-WL450
1 Attach Wall-Mount Attachment (supplied with the TV) to the rear of the TV (to make it
parallel with the wall).
Note
If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}.
Be sure to fasten the Wall-Mount Attachment when attaching them to the TV.
Use only a flat head screwdriver to install the Wall-Mount Attachment. Use of another tool might result in over
torqueing the Wall-Mount Attachment and damaging the TV.
2 Make sure that the wall has enough space for the TV and is capable of supporting a
weight of at least four times that of the TV. Refer to the following table on installing the TV
to the wall. See page 22-24 (Specifications) for the TV’s weight.
Soft cloth
1.5 N∙m
{15 kgf∙cm}
Screen centre point
80
Standard mounting Slim mounting
19
GB
GB
Unit: mm
Note
Figures in the table may differ slightly depending on the installation.
When your TV is installed on the wall, the upper side of the TV slightly leans forward.
3 Attach the Attachment parts for Wall-Mount Bracket. Check the Attachment parts by
referring to “1” of the Wall-Mount Bracket Installation Guide.
Note
If using an electric screwdriver, set the torque at approximately 1.5m {15 kgf·cm}.
Be sure to store the unused parts in a safe place for future use. Retain this manual for future reference.
Standard mounting
Slim mounting
Note
You cannot use some of the terminals on the rear of the TV when using this mounting style.
Model Name
KDL-
Display dimensions
Screen
centre
dimension
Length for mounting
Standard
mounting
Slim
mounting
50W800C 1,116 654 127 464 122 80
43W800C 962 565 173 464 122 80
Pulley
Screw (+PSW 6 x 20)
Spacer (60 mm)
Screw (+PSW 6 x 50)
Belt
Soft cloth
Soft cloth
20
GB
4 Connect necessary cables to the TV.
Note
You cannot access to any terminal after installing the TV to the wall.
5 Install the TV to the Base. Refer to “5” of Installation Guide and “Installing the TV to the
Wall” of Operating Instructions supplied with the Wall-Mount Bracket.
Refer to the instructions supplied with the Wall-Mount Bracket for your model to install the TV on the wall.
Model Name KDL- Hook location
50W800C/
43W800C
a
Screw (+PSW 6 x 20)
Pulley
Screw (+PSW 6 x 20)
Belt
Spacer (20mm)
Soft cloth
a
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Sony KDL-50W800C リファレンスガイド

カテゴリー
液晶テレビ
タイプ
リファレンスガイド
このマニュアルも適しています

他の言語で