DSPPA MP9813D 取扱説明書

カテゴリー
防火
タイプ
取扱説明書
MP9813D
INDIRECT SPEAKER SELECTOR
OWNERS MANUAL
Before operating, please read this manual completely.
FEATURES
l 2CH inputs, 10CH outputs.
l All call button.
l The channel will be switched to input B automatically while alarming.
* * Indirect Speaker Selector
MP9813D
1
FRONT PANEL
REAR PANEL & CONNECTIONS
*ALARM IN to be connected to fire center
l 1-10 Live Terminals of CH1-CH10 respectively
l 14-25 COM
1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 ,16 ,17 18 19 ,20 21, 22 23 ,24 ,25
1 2 3 4
1 Power switch. (1 is power on and the power LED is on )
2 Power indicator. 3 Distributor. 4 All call button.
Power Amp. A
MP series
for BGM
Power Amp. B
MP series
for EMC
ALM OUTPUT to
Timer / Siren Device
Emergency
from FIRE center*
Guangzhou DSPPA Audio Co., Ltd.
* * Indirect Speaker Selector
MP9813D
2
OPERATION
1. Make BGM signal input from A terminal while EMC signal input from B terminal on the rear panel.
We also can make A, B together with short circuit if there is none of BGM amplifier.
2. Press down any Distributor key to switch on channels which you want.
3. Click All call button with its LED lit and all Switch indicators lit. In this case, all Switching keys
are no use. Click All call button again and its LED gone off, In this case, all Switching keys are use.
4. Pin 1-10 of ALARM INport are live terminals of CH1-CH10 respectively while pin 14-25 are
com. Every channel will be switch to B while alarm signal (short circuit signal) is fed to ALARM IN.
5. An grounded Alarm signal will be send out fromALARM OUTwhile any alarm signal
appears onALARM IN.
SPECIFICATIONS
Channels 10, switch able
Input capacity
70-100V 10A
Channel capacity
70-100V 5A/CH
ALM
0/+24V, 0short circuitis Valid
Protection AC fuse
Power Requirement AC 220-240V/50-60Hz
Outer Packing Size( mm)
L×W×H530×440×195
Unit Size (mm)
L×W×H484×365×88
Gross weight 8.3kg
Net weight 6.5kg
Specifications are subject to be changed without notice.
CAUTION
When the Power switcher is off, please pull out the power cord from the socket.
Please keep the equipment out of water.
To reduce the risk of electric shock, do not remove the cover.
No user parts inside. Refer servicing to qualified service personnel.
Guangzhou DSPPA Audio Co., Ltd.
* * 广播分区器
MP9813D
3
MP9813D
广播分区器
使用说明
欢迎惠顾您对本品之选显示了的专业使用前请细阅读说明书。
性能特点
l 2 路输入(A B) 10 输出。
l 行插入功能。
l 便的全开全关能控制。
l 警报信号输时,相应道自动切到通道 B
* * 广播分区器
MP9813D
4
前面板
后面板及连接
*ALARM IN 连接
l 1-10 热端,分对应于 CH1-CH10
l 14-25 公共端
1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 ,16 ,17 18 19 ,20 21, 22 23 ,24 ,25
1 2 3 4
1 电源开关按下 1 源指亮) 2 指示
3 分区选择键 4 全开全控制开关
A 功放
MP series
乐)
B 功放
MP series
广播)
输出
时器
/
报器
信号
中心*
Guangzhou DSPPA Audio Co., Ltd.
* * 广播分区器
MP9813D
5
使用方法
1. 背景音乐号由后面 A 广播信号由 B 如无急广播用功放,
AB 子并接)。
2. 任一分区选键,对应的应指示选通区。
3. 开全关键,其相的指示灯点亮,其他十个区控制的指示灯也同时亮,
其他十个控制键不能控制区。再次下“全开全关键,对的指示灯熄
其他十个分区控制键分区了。
4. 警报输入口ALARM IN连接)的 14-25 为公共地线;第 1 10 号端分别
对应管理 CH1-CH10 十个任一相当警,应通道扬声强切到 B
5. 警报输入口ALARM IN任一子有警报号输时,报信号输出ALARM OUT
即有报警号输出,用于动处待机状态时器以及激发警报信号发生器。
注意:现未按下任何分区择键,而该分区指示亮且选通分区选通的情况,可能是
报输入口ALARM IN”有短路激活信号(不一是从中心来报警信号)
性能规格
道数 10, 可任意选通
入容量
70-100V , 10A
输出容量 每个 70-100V , 5A
警报信号 0/+24V, 0V短路有效
保护 AC 保险丝
电源
AC 220-240V/50-60Hz
外包装尺寸mm ××530×440×195
尺寸mm ××484×365×88
毛重
8.3kg
净重
6.5kg
如有变恕另行
设备源开关状态时,并未电源,为使用
设备,请电源线插头拔插座
设备不能遭受水或水溅不能满水花瓶品放置在设备上
勿随电。必要专业之专业员进行修
Guangzhou DSPPA Audio Co., Ltd.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

DSPPA MP9813D 取扱説明書

カテゴリー
防火
タイプ
取扱説明書

他の言語で