Philips S7980/68 ユーザーマニュアル

S7980

1

2

3

8

9

10

13

15

14

11

12

4

5

6

7

16

17

18

empty page before TOC

English 6

简体中文

35

English

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benefit from the support that

Philips offers, register your product at

www.philips.com/welcome or via the SkinAnalyst

app.

Introducing Philips’ first ever complete shaving and

skincare system. Assess and measure the

condition of your skin, personalize your FaceSmart

shaving and cleansing settings, and best of all,

receive daily skincare advice tailored to you.

General description (Fig. 1)

1 Protection cap for cleansing brush

2 Cleansing brush

3 Cleansing brush base

4 Shaving unit

5 On/off button

6 Handle

7 Socket for small plug

8 SkinAnalyst sensor

9 Notification symbol

10 Shaving unit detector

11 Cleansing brush detector

12 Cleaning reminder

13 Bluetooth® symbol

14 Travel lock symbol

15 Battery charge indicator

16 Pouch

17 Supply unit (adapter)

18 Small plug

Consult the quick start guide and app for

instructions on how to connect the

SkinAnalyst sensor with the app and on how

to use the app to get personalized skincare

advice.

6

English

Read this important information carefully before

you use the shaver, the Skinanalyst sensor and

save it for future reference. The accessories

supplied may vary for different products.

Danger

- Keep the supply unit dry.

Warning

- To charge the battery, only use the detachable

supply unit (type HQ8505) provided with the

shaver.

- The supply unit contains a transformer. Do not

cut off the supply unit to replace it with another

plug, as this causes a hazardous situation.

- The shaver and SkinAnalyst sensor can be used

by children aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience and

knowledge if they have been given supervision

or instruction concerning use of both

appliances in a safe way and understand the

hazards involved. Children shall not play with

the shaver. Cleaning and user maintenance

shall not be made by children without

supervision.

- Always unplug the shaver before you clean it

under the tap.

- Always check the shaver and SkinAnalyst

sensor before you use it. Do not use it if it is

damaged, as this may cause injury. Always

replace a damaged part with one of the original

type.

7

English

- Do not open the shaver to replace the

rechargeable battery.

Caution

- Never use water hotter than 80°C to rinse the

shaver.

- Never rinse the SkinAnalyst sensor under the

tap.

- Only use the shaver and the SkinAnalyst sensor

for its intended purpose as shown in the user

manual.

- For hygienic reasons, the shaver should only be

used by one person.

- Never use compressed air, scouring pads,

abrasive cleaning agents or aggressive liquids

such as petrol or acetone to clean the shaver.

- Water may drip from the socket at the bottom

of the shaver when you rinse it. This is normal

and not dangerous because all electronics are

enclosed in a sealed power unit inside the

shaver.

- Do not use the supply unit in or near wall

sockets that contain an electric air freshener to

prevent irreparable damage to the supply unit.

- Keep your iPhone away from water and moist

environments.

- The shortwave radio frequency signals of a

Bluetooth shaver may impair the operation of

other electronic and medical devices.

8

English

- Do not use the shaver in medical facilities,

aircraft, refuelling points, close to automatic

doors, automatic fire alarms or other

automatically controlled devices.

- Switch off Bluetooth where it is prohibited.

- Keep this shaver at least 20 cm from

pacemakers and other medical devices. Radio

waves may impair the operation of pacemakers

and other medical devices.

Electromagnetic fields (EMF)

- This Philips shaver complies with all shaver

standards and regulations regarding exposure

to electromagnetic fields.

General

- This shaver is waterproof. It is suitable for use in

the bath or shower and for cleaning under the

tap. For safety reasons, the shaver can

therefore only be used without cord.

- The shaver is suitable for mains voltages

ranging from 100 to 240 volts.

- The supply unit transforms 100-240 volts to a

safe low voltage of less than 24 volts.

- The frequency band in which the shaver

operates is 2.4 GHz.

- The maximum radio frequency power radiated

in the frequency band in which the shaver

operates is <10dBm.

9

English

The display

'Notification' symbol

The shaver is equipped with a notification symbol.

This symbol lights up when important advice is

available in the app. Go to the app to obtain this

advice. It reminds you to unplug the shaver before

you switch it on and to clean it for optimal

performance. It also reminds you to replace the

shaving heads every two years or the cleansing

brush every three months.

Attachment detection feature

When you have paired your iPhone with the

shaver, the attachment detection feature is

activated. Every time you switch on the shaver, this

feature automatically recognizes the attachment

(shaving unit/cleansing brush) that is attached to

the shaver handle and adapts the settings

accordingly. Unpairing of your iPhone and the

shaver deactivates this feature.

Manually select attachment

Make sure your shaver is connected to your

iPhone. The SkinAnalyst app also offers the

possibility to (de)activate the Attachment

detection feature. You can do this by going to My

profile, My shaver and switching off the Auto

attachment detection. You can then manually

select the brush attachment, by switching on the

shaver and press and hold the on/off button for

one second.

1 sec.

10

English

Shaving unit detector

The shaving unit detector lights up to indicate that

the shaving unit has been attached to the handle.

Cleansing brush detector

The cleansing brush detector lights up to indicate

that the cleansing brush has been detected.

Cleaning reminder

When you switch off the shaver, the cleaning

reminder flashes to remind you to clean the

shaver. Clean the shaver and the attachments after

each use for optimal performance.

Bluetooth®

The shaver is equipped with Bluetooth 4.0 to

connect your shaver to the app on your iPhone.

Bluetooth is automatically activated when you

switch on the shaver for the first time. You can only

deactivate it by switching on the travel lock.

Travel lock

You can lock the shaver when you are going to

travel. The travel lock prevents the shaver from

being switched on by accident. The travel lock also

deactivates Bluetooth.

11

English

Activating the travel lock

3 sec.

1 Press the on/off button for 3 seconds to enter

the travel lock mode.

While you activate the travel lock, the travel lock

symbol flashes. When the travel lock is activated,

the travel lock symbol lights up continuously.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

The travel lock symbol flashes and then goes out.

The shaver is now ready for use and Bluetooth is

activated again.

Charging

Battery charge indicator

Charging takes approx. 1 hour.

Quick charge: When the battery is empty and you

connect the shaver to the wall socket, the battery

charge indicator flashes quickly. When the shaver

contains enough energy for one shaving or

cleansing session, the battery charge indicator

starts flashing slowly..

While the shaver continues to charge, the battery

charge indicator flashes slowly until the battery is

fully charged.

12

English

Battery fully charged

When the battery is fully charged, the battery

charge indicator lights up blue continuously.

Note: The shaver can only be used without cord.

Note: When the battery is full, the display switches

off automatically after 30 minutes. If you press the

on/off button during charging, the notification

symbol lights up blue to remind you that you have

to disconnect the shaver from the wall socket.

Battery low

When the battery is almost empty, the battery

charge indicator flashes orange.

When the battery is completely empty, the battery

charge indicator flashes orange quickly.

Charging

Charging takes approx. 1 hour.

Charge the shaver before first use and when the

display indicates that the battery is almost empty.

Note: You can charge the shaver after every use.

This will not harm the battery.

Charging with the supply unit

1 Make sure the shaver is switched off.

1

2

2 Insert the small plug into the shaver and put the

supply unit in the wall socket.

3 After charging, remove the supply unit from the

wall socket and pull the small plug out of the

shaver.

13

English

Preparing for use

Pairing the shaver and your iPhone

For this shaver a special app is available. You can

download the SkinAnalyst app from the App store.

By using the app, your skincare and shaving

routine will be personalized. The app gives you

expert advice based on your skin, shaving method,

local weather conditions, etc. to support your daily

skincare and shaving routine.

Note: The app is available for iPhone 6, iPhone 6

Plus, iPhone 6S and iPhone 6S Plus equipped with

iOS9 or higher.

To create a secure and safe connection, first the

shaver and your iPhone need to be paired once.

1 Download the SkinAnalyst app from the App

store.

2 Make sure Bluetooth on your iPhone is

switched on.

S7920

3 Open the app on your iPhone.

4 Follow the instructions in the app. After you

have filled in the skin assessment, the app asks

you to pair your iPhone with the shaver.

5 Switch on the shaver. Bluetooth is activated

automatically.

14

English

6 In the app, the pop-up message 'press pair'

appears. When your iPhone and the shaver

have been paired successfully, the Bluetooth

symbol flashes briefly and then goes out. If this

does not happen, please see 'Troubleshooting'.

7 Once the shaver and the app have been paired,

the shaver automatically selects the right

personal settings depending on the attachment

you have clicked on. During shaving or

cleansing, you can open the app to see the

settings you are using and the duration of the

shaving or cleansing session.

Note: When you use the shaver, keep your

iPhone and shaver within transmission range

(no more than 5 meters from each other, in the

same room).

Using the shaver

Using the SkinAnalyst sensor

1 Open the app before measuring your skin.

1

2

2 If you have an iPhone case, first remove the

case from your iPhone.

3 Pull the clamp of the SkinAnalyst sensor

outwards and gently place your iPhone into the

holder with its camera pointing towards the

opening on the inside of the holder. Be careful

when you attach or remove the SkinAnalyst

sensor to prevent scratches on your iPhone.

Note: The SkinAnalyst sensor can only be used

on iPhone 6, iPhone 6 Plus, iPhone 6S and

iPhone 6S Plus equipped with iOS9 or higher.

15

English

4 Insert the jack plug of the SkinAnalyst sensor

into your iPhone.

5 Remove the protection cap from the

SkinAnalyst sensor.

Note: Above instructions are also shown in the

app.

The SkinAnalyst sensor only works if you

remove the case of your iPhone.

6 Follow the instructions in the app to measure

your skin.

Note: Keep the SkinAnalyst sensor placed on

the skin during measurement to avoid flashing

into your eyes.

-Do not look into the sensor before and after

skin measurement.

-When you take a picture of the skin, please

position the sensor flat onto your skin so to

ensure it can take a clear picture of your skin.

Connecting with the shaver

1 Make sure Bluetooth on your iPhone is

switched on.

S7920

2 Open the app on your iPhone.

3 When paired, the shaver and the app connect

automatically. You can now start with your daily

skincare routine.

Note: Make sure you have a good internet

connection to fully benefit from the app.

4 Synchronize the shaving and cleansing data on

the shaver and the app (see 'Synchronizing your

shaves and cleansing treatments').

16

English

5 Keep your iPhone and shaver close to each

other in order to stay connected.

Caution: Do not use your iPhone in moist

surroundings. Moisture and water can damage

your iPhone.

Switching the shaver on and off

1 To switch on the shaver, press the on/off

button once.

2 To switch off the shaver, press the on/off

button once.

Synchronizing your shaves and cleansing treatments

In order to benefit optimally from the treatments,

you have to synchronize your treatments regularly.

The shaver can store up to 15 shaves and/or

cleansing treatments, so make sure you

synchronize the shaver at least once after every 15

treatments. As an extra reminder, the notification

symbol flashes every 9 treatments, without a

connection between the shaver and the app, to

tell you to connect with the app.

1 Open the app and make sure you are close to

the shaver.

2 The app connects with the shaver automatically

and synchronizes your last shaves or cleansing

treatments.

17

English

Using the attachments

Note: Attach the cleansing brush on the cleansing

brush base first, before you place it on the shaver.

Removing or attaching the attachments

1 Make sure the shaver is switched off.

2 Pull the attachment straight off the shaver.

Note: Do not twist the attachment while you

pull it off the shaver.

3 Insert the lug of the attachment into the slot in

the top of the shaver. Then press down the

attachment to attach it to the shaver (‘click’).

Using the cleansing brush

Use the rotating cleansing brush with your daily

cleansing cream. The cleansing brush removes oil

and dirt, contributing to a healthy and oil-free skin.

We advise you to use it no more than twice a day.

It is recommended not to use the cleansing brush

directly after shaving to prevent skin irritation. For

better shaving results, use the cleansing brush

before shaving.

Caution: Do not use the shaver on damaged or

irritated skin or on wounds.

1 Attach the cleansing brush to the shaver ('click').

18

English

2 Moisten the cleansing brush with water.

Note: Do not use the shaver with a dry

cleansing brush, as this can irritate the skin.

3 Moisten your face with water and apply a

cleanser to your face.

4 Place the cleansing brush on your cheek.

5 Switch on the shaver.

20 sec.

6 Gently move the cleansing brush across your

skin from the nose towards the ear. Do not

push the cleansing brush too hard onto the skin

to make sure the treatment remains

comfortable.

Note: Do not cleanse the sensitive area around

your eyes.

20 sec.

7 After approx. 15-20 seconds (depending on the

selected setting), the shaver pulsates twice to

indicate that you have to move the shaver to

your other cheek. Start cleansing this part of

your face. After approx. 15-20 seconds, move

the shaver to your other cheek and start

cleansing this part of your face.

20 sec.

8 After approx. 15-20 seconds, the shaver

pulsates twice to indicate that you have to

move the shaver to your forehead. Start

cleansing this part of your face. Gently move

the brush head from left to right. The shaver

stops automatically after it has completed the

program for the entire face.

19

English

Note: We advise you to not overdo the

cleansing and to not cleanse any zone longer

than 15-20 seconds.

9 After the treatment, rinse and dry your

face.Your face is now ready for the next step of

your daily skincare routine.

10 Clean the cleansing brush after use.

Cleansing brush settings

The app has a feature that allows you to

personalize you cleansing settings. Go the Usage

Tracker and change the cleansing brush settings.

You can adjust the settings and choose between

four settings depending on your personal

cleansing needs: sensitive, dry, normal or oily.

Using the shaving unit

Note: This shaver can only be used without cord.

Skin adaptation period

Your first shaves may not bring you the result you

expect and your skin may even become slightly

irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system. We

advise you to follow the advice provided by the

app and shave regularly (at least 3 times a week)

with this shaver for a period of 4 weeks to allow

your skin to adapt to the new shaver.

Dry shaving

1 Switch on the shaver.

2 Move the shaving heads over your skin in

circular movements to catch all hairs growing in

different directions. Make sure each shaving

head is fully in contact with the skin. Exert

gentle pressure for a close, comfortable shave.

20

English

ページが読み込まれています...

Philips S7980/68 ユーザーマニュアル

Philips S7980/68 ユーザーマニュアル

他の言語で

関連論文