Dell PowerEdge R300 クイックスタートガイド

Dell™ PowerEdge™

R300 Systems

Getting Started

With Your System

系统使用入门

はじめに

시스템시작하기

Dell™ PowerEdge™

R300 Systems

Getting Started

With Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.; Intel,

Pentium, Celeron and Xeon are registered trademarks and Core is a trademark of Intel Corporation

in the U.S. and other countries; Microsoft, Windows, and Windows Server are either tradcmarks or

registered trademarks of Microsoft Corporation in the United States and/or other countries; Red Hat

and Enterprise Linux are registered trademarks of Red Hat Inc.; SUSE is a registered trademark

of Novell Inc..

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model SMT

December 2007 P/N MM428 Rev. A00

Getting Started With Your System 3

System Features

The major hardware and software features of your system include:

• 1U/1S rack-mountable chassis with support for static rails and sliding rails.

NOTE: Use the System Setup program to view processor information. See

"Using the System Setup Program" in your Hardware Owner’s Manual.

• One of the following processors:

– Single Core Intel

®

Celeron

®

445 Processor

– Dual-Core Intel Core™2 Duo E6305 or E6405 Processor

– Quad-Core Intel Xeon

®

X3323, X3353, or X3363 Processor

• A minimum of 512-MB single or dual-ranked registered 667-MHz DDR2

memory modules with ECC, upgradeable to a maximum of 24-GB by

installing combinations of 512-MB, 1-GB, 2-GB, or 4-GB memory modules

in six memory module sockets on the system board.

• One of the following riser card options:

– Two riser cards (left and center risers), each providing a x8 lane width

PCI-Express expansion slot.

OR

– One riser card (center riser), providing a x8 lane width PCI-Express

expansion slot.

– One riser card (left riser) providing a 3.3 V, 64-bit 133MHz PCI-X

expansion slot.

• One 12.7 mm DVD, or combination CD-RW/DVD in a device drive bay.

• Support for the following internal hard-drive configurations:

– Up to two 3.5-inch, internal, SATA hard drives with the optional SAS

controller card (hot-plug option available).

– Up to two 3.5-inch, internal, Serial-Attached SCSI (SAS) hard drives

with an optional SAS controller card (hot-plug option available).

4 Getting Started With Your System

• Optional remote access controller for remote systems management, which

is installed on the dedicated slot on the system board.

• Optional USB flash drive emulates a diskette drive or hard drive.

• One 400-W power supply (optional redundant power supply available).

• Two integrated Gigabit Ethernet network adapters, capable of supporting

10-Mbps, 100-Mbps, and 1000-Mbps data rates with support for Wake-

on-LAN.

• A Dell Remote Access Controller Card (DRAC5), which provides remote

system management, crashed system recovery, and power control functions

for Dell PowerEdge

.

•

An integrated VGA-compatible video subsystem with an ATI ES1000,

33-MHz PCI video controller. This video subsystem contains a

minimum of 32MB of graphics memory with support for 2D graphics.

Maximum resolution is 1600 x 1200 with 65,536 colors; true-color

graphics are supported in the following resolutions: 640 x 480, 800 x 600,

1024 x 768, 1280 x 1024. When the optional remote access card is

installed, the maximum video resolution is 1280 x 1024

.

• Fan modules, each of which is comprised of two dual-rotor fans positioned

in front of the processor and memory.

• Fan modules, comprised of two dual-rotor fans positioned in front of the

PSU. These fans are used for the two redundant PSUs (hot-plug hard

drives and redundant PSU configuration).

• Serial connector for console redirection support.

• Security features, including chassis-intrusion detection and keylock

on the optional bezel.

• An integrated Trusted Platform Module (TPM) version 1.2 used for

security applications, capable of generating and storing keys, and storing

passwords and digital certifications. (Not available in China.)

Getting Started With Your System 5

• Systems management software/circuitry that monitors critical system

voltages and temperatures.

• Back-panel connectors include video, serial, two USB, and two network

adapter connectors.

• Front-panel connectors include one VGA and two USB connectors.

• One internal USB connector is included for a bootable memory key.

• Front-panel 1x5 LCD for system ID and error messaging.

For more information about specific features, see “Technical Specifications”

on page 11.

The following software is included with your system:

• A System Setup program for viewing and changing system configuration

information. For more information, see “Using the System Setup Program”

in the

Hardware Owner’s Manual

.

• Enhanced security features, including a system and setup passwords are

available through the System Setup program.

• Video drivers for displaying programs in high-resolution modes.

Systems management software and documentation CDs.

Supported Operating Systems

• Microsoft

®

Windows Server

®

2008 Web, Standard, and Enterprise

(32-bit x86) Editions (

when available

)

• Microsoft Windows Server 2008 Web, Standard, Small Business Server

(Premium and Standard), and Enterprise (x64) Editions (

when available

)

• Microsoft Windows Server 2003 Web, Standard, Small Business Server

(Premium and Standard), and Enterprise (32-bit x86) Editions

(SP1 and SP2)

• Microsoft Windows Server 2003 Standard and Enterprise (x64) Editions

• Microsoft Windows Server 2003 R2 Standard, Small Business Server

(Premium and Standard), and Enterprise (32-bit x86) Editions

6 Getting Started With Your System

• Microsoft Windows Server 2003 R2 Standard and Enterprise (x64)

Editions

•Red Hat

®

Enterprise Linux

®

ES (versions 4 and 5) (x86_32)

• Red Hat Enterprise Linux ES (versions 4 and 5) (x86_64)

•SUSE

®

Linux Enterprise Server 9 (SP4 or later) (x86_64)

• SUSE Linux Enterprise Server 10 (x86_64)

NOTE: For the latest information on supported operating systems,

see www.dell.com.

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and

regulatory information. Warranty information may be included within this

document or as a separate document.

•The

Rack Installation Guide

or

Rack Installation Instructions

included

with your rack solution describes how to install your system into a rack.

•The

Getting Started Guide

provides an overview of system features,

setting up your system, and technical specifications.

•The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install

or replace system components.

• CDs included with your system provide documentation and tools

for configuring and managing your system.

• Systems management software documentation describes the features,

requirements, installation, and basic operation of the software.

• Operating system documentation describes how to install (if necessary),

configure, and use the operating system software.

• Documentation for any components you purchased separately provides

information to configure and install these options.

Getting Started With Your System 7

• Updates are sometimes included with the system to describe changes

to the system, software, and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates

first because they often supersede information in other documents.

• Release notes or readme files may be included to provide last-minute

updates to the system or documentation or advanced technical reference

material intended for experienced users or technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not

perform as expected, see your Hardware Owner’s Manual.

Dell Enterprise Training and Certification is available; see

www.dell.com/training for more information. This service may not be offered

in all locations.

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety

instructions and important regulatory information in your Product Information

Guide.

CAUTION: Whenever you need to lift the system, get others to assist you. To avoid

injury, do not attempt to lift the system by yourself.

This section describes the steps to set up your system for the first time.

Unpacking the System

Unpack your system and identify each item. Keep all shipping materials in

case you need them later.

8 Getting Started With Your System

Installing the Rail and System in a Rack

Install the system in the rack once you have read the “Safety Instructions”

located in the rack installation documentation for your system.

See your rack installation documentation for instructions on installing your

system in a rack. For power and cooling guidelines, see the rack capacity

planner tool on www.dell.com.

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Getting Started With Your System 9

Connecting the Power

Connect the system’s power cable(s) to the system (a redundant system is

shown in the illustration). For redundant systems, secure the cables with the

two Velcro straps that ship with your system, as shown. For non-redundant

systems, attach the power cord retention bracket that ships with your system.

Plug the other end of the cable into a grounded electrical outlet or a separate

power source such as an uninterrupted power supply (UPS) or a power

distribution unit (PDU).

Turning on the System

Turn on the system and monitor (optional).

10 Getting Started With Your System

Press the power button on the system and the monitor. The power indicators

should light. Adjust the monitor’s controls until the displayed image is

satisfactory.

Installing the Bezel

Install the bezel (optional).

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the Quick Installation Guide. Be sure the operating system

is installed before installing hardware or software not purchased with the

system.

Getting Started With Your System 11

Technical Specifications

Processor

Processor type Single Core Intel

®

Celeron

®

445 processor

or

Dual-Core Intel Core

™

2 Duo E6305 or E6405

sequence processor

or

Quad-Core Intel Xeon

®

X3323, X3353, or X3363

serial processor

Expansion Buses

Bus type PCI-X, PCIe

Expansion slots – Two optional riser cards

Riser 1

PCIe Center Riser

One full-height, half-length, x8 lane PCIe slot

PCIe Left Riser

One full-height, half-length, x8 lane PCIe slot

Riser 2

PCI-X Left Riser

One full-height, half-length,

64-bit, 133MHz PCI-X slot

PCIe Center Riser

One full-height, half-length, x8 lane PCIe slot

Memory

Architecture Up to six registered DDR2 677 MHz RDRAM

memory modules with ECC

Memory module sockets Six 240-pin

Memory module capacities 512 MB, 1 GB, 2 GB, 4GB

Minimum RAM 512 MB (one 512-MB module)

Maximum RAM 24 GB

12 Getting Started With Your System

Drives

Hard Drives

SATA

Up to two 3.5-inch, internal

(optional for hot-plug)

SAS

Up to two 3.5-inch, internal with optional SAS

controller card (optional for hot-plug)

CD/DVD drive One optional DVD, or combination

CD-RW/DVD in a device drive bay

NOTE: DVD devices are data only.

USB flash drive One optional drive that emulates a diskette drive

or hard drive

Connectors

Externally accessible

Back

Network adapter

Two RJ-45 (for integrated 1-Gigabit network

adapters)

Serial

9 pin

USB

Two 4-pin, USB 2.0 compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0 compliant

Internally accessible

SATA channels

Three 7-pin

USB key (for memory key)

one 4-pin, USB 2.0-compliant

Getting Started With Your System 13

Video

Video type Integrated ATI ES1000 VGA controller

Video memory 32 MB (Min)-64 MB (Max) DDR II

Power

AC power supply

Wattage

400 W redundant PSU for hot-plug hard

drives plus redundant PSU configuration

(maximum configuration)

Voltage

100–240 VAC, 50/60 Hz

Maximum inrush current

Under typical line conditions and over

the entire system ambient operating range,

the inrush current may reach 25 A for 10 ms

or less

System battery CR 2032 3.0-V lithium coin cell

Physical

Height 4.2 cm (1.67 in)

Width 42.6 cm (16.78 in)

Depth

With optional bezel

69.3 cm (27.29 in)

Without optional bezel

66 cm (26 in)

Weight (maximum

configuration Kg)

13.45 kg (29.6 lb)

14 Getting Started With Your System

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz for 15 min

Storage

1.54 Grms at 10–250 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 31 G for up to

2.6 ms

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3,048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2,950 feet, the maximum

operating temperature is derated 1°F/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne Contaminant Level

Class

G2 or lower as defined by ISA-S71.04-1985

Dell

™

PowerEdge

™

R300

系统

使用入门

注、注意和警告

注： “注”表示可以帮助您更好地使用计算机的重要信息。

注意：“注意”表示可能会损坏硬件或导致数据丢失、并告诉您如

何避免此类问题。

警告：“警告”表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本说明文件中的信息如有更改、恕不另行通知。

未经

Dell Inc.

书面许可、严禁以任何形式进行复制。

本文中使用的商标：

Dell

、

DELL

徽标和

PowerEdge

是

Dell Inc.

的商标；

Intel

、

Pentium

、

Celeron

、

Xeon

和

Core

是

Intel Corporation

在美国

和

/

或其它国家

/

地区的注册商标和商标；

Microsoft

、

Windows

和

Windows Server

是

Microsoft Corporation

在美国和

/

或其它国家

/

地区

的注册商标；

Red Hat

和

Enterprise Linux

是

Red Hat Inc.

的注册商标；

SUSE

是

Novell Inc.

的注册商标。

本说明文件中述及的其它商标和产品名称是指拥有相应商标和产品名称的公司或其制造的

产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。

型号

SMT

2007

年

12

月

P/N MM428 Rev. A00

系统使用入门 17

系统功能

系统的主要硬件和软件配置包括：

•

1U/1S

机架可固定机箱、支持静态滑轨和滑动滑轨。

注：使用系统设置程序可以查看处理器信息。请参阅硬件用户手册

中的“使用系统设置程序”。

•

以下处理器之一：

–

单核

Intel

®

Celeron

®

445

处理器

–

双核

Intel Core

™

2 Duo E6305

或

E6405

处理器

–

四核

Intel Xeon

®

X3323

、

X3353

或

X3363

处理器

•

最小

512 MB

的单列或双列带寄存器的

667 MHz DDR2

内存模块

（具有

ECC

）、可通过在系统板上的

6

个内存模块插槽中组合安装

512 MB

、

1 GB

、

2 GB

或

4 GB

内存模块、将内存最大升级至

24 GB

。

•

以下提升卡选件之一：

–

两个提升卡（左提升板和中央提升板）、每个提供一个

x8

信道宽

度的

PCI Express

扩充槽。

或

–

一个提升卡（中央提升板）、提供一个

x8

信道宽度的

PCI Express

扩充槽。

–

一个提升卡（左提升板）、提供一个

3.3 V

、

64

位

133MHz PCI-X

扩充槽。

•

一个

12.7 mm DVD

、或设备驱动器托架中的组合

CD-RW/DVD

。

•

支持以下内部硬盘驱动器配置：

–

最多两个

3.5

英寸、内部

SATA

硬盘驱动器、带可选

SAS

控制器卡

（可热插拨）。

–

最多两个

3.5

英寸、内部

Serial-Attached

硬盘驱动器、带可选

SCSI

控制器卡（可热插拨）。

•

可选远程访问控制器、用于远程系统管理、安装在系统板的专用插

槽上。

•

可选

USB

闪存盘模拟软盘驱动器或硬盘驱动器。

•

一个

400 W

电源设备（备有可选的冗余电源设备）。

18 系统使用入门

•

两个集成吉位以太网网络适配器、可支持

10 Mbps

、

100 Mbps

和

1000 Mbps

数据速率、支持通过

LAN

唤醒。

•

一个

Dell

远程访问控制器卡

(DRAC5)

、可为

Dell PowerEdge

提供远程

系统管理、崩溃系统恢复和电源控制功能。

•

VGA

兼容集成视频子系统、带有

ATI ES1000

、

33 MHz PCI

视频

控制器。此视频子系统包含一个最小

32MB

的图形内存、支持二维

图形。最大分辨率是

1600 x 1200

（

65,536

色）；以下分辨率支持真

彩色图形：

640 x 480

、

800 x 600

、

1024 x 768

、

1280 x 1024

。安装

了可选远程访问卡时、最大视频分辨率为

1280 x 1024

。

•

风扇模块、每个模块由两个双转子风扇组成、位于处理器和内存前面。

•

风扇模块、由两个双转子风扇组成、位于

PSU

前面。这些风扇用于两

个冗余

PSU

（热插拨硬盘驱动器和冗余

PSU

配置）。

•

支持控制台重定向的串行连接器。

•

安全保护功能部件、包括机箱防盗检测功能和可选挡板上的键锁。

•

一个集成的受信任的平台模块

(TPM)

（

1.2

版）、用作安全应用程序、

可生成并存储密钥以及存储密码和数字证书（中国不可用）。

•

系统管理软件

/

电路、用于监测系统临界电压和温度。

•

背面板连接器包括视频、串行、两个

USB

和两个网络适配器连接器。

•

前面板连接器包括一个

VGA

连接器和两个

USB

连接器。

•

一个内部

USB

连接器、用于可引导存储钥匙。

•

前面板

1x5 LCD

显示屏、用于显示系统

ID

和错误信息。

有关特定配置的详细信息、请参阅第

23

页上的“技术规格”。

您的系统附带以下软件：

•

系统设置程序、用于查看和更改系统配置信息。有关详情、请参阅硬

件用户手册中的 “使用系统设置程序”。

•

增强的安全保护功能、包括系统密码和设置密码、可通过系统设置程

序进行设置。

•

视频驱动程序、用于在高分辨率模式下显示程序。

系统管理软件和说明文件

CD

。

ページが読み込まれています...

Dell PowerEdge R300 クイックスタートガイド

このマニュアルも適しています

Dell PowerEdge R300 クイックスタートガイド

他の言語で

関連論文