Dell PowerEdge R200 クイックスタートガイド

Dell™ PowerEdge™

R200 Systems

Getting Started

With Your System

系统使用入门

はじめに

시스템시작하기

Dell™ PowerEdge™

R200 Systems

Getting Started

With Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.;

Intel, Pentium, and Celeron are registered trademarks and Core is a trademark of Intel Corporation;

Microsoft, Windows, and Windows Server are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries; Red Hat is a registered trademark of Red Hat,

Inc.; SUSE is a registered trademark of Novell Inc. in the United States and other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model SVP

August 2007 P/N NM215 Rev. A00

Getting Started Guide 3

System Features

The major hardware and software features of your system include:

• 1U/1S rack-mountable chassis with support for static rails and sliding rails.

NOTE: Use the System Setup program to view processor information.

See "Using the System Setup Program" in your Hardware Owner’s Manual.

• One of the following processors:

–Intel

®

Celeron

®

– Intel Pentium

®

Dual-Core™

– Intel Core 2 Duo™

– Dual-Core Intel Xeon

®

Processor 3000 Series

– Quad-Core Intel Xeon Processor 3200 Series.

• A minimum of 512 MB of 667-MHz or 800-MHz DDR2 SDRAM memory,

upgradable to a maximum of 8 GB by installing combinations of 512-MB,

1-GB, or 2-GB unbuffered ECC memory modules in four memory module

sockets on the system board.

• One of the following riser card options:

– One full-height, half-length, x8 lane PCIe expansion slot and one full-

height, half-length PCIe expansion slot with a x8 connector but with

a x4 lane capability.

– One full-height, half-length, 133MHz/64 bit PCI-X expansion slot and

one full-height, half-length, x8 lane PCIe expansion slot, which

includes a connector for an optional remote access controller (RAC)

card.

• One 3.5-inch CD, DVD, or combination CD-RW/DVD in a peripheral

drive bay.

• Support for the following internal hard-drive configurations:

– Up to two internal, 1-inch high, SATA hard drives with the integrated

drive controllers.

– Up to two internal, 1-inch high optional Serial-Attached SCSI (SAS)

hard drives with an optional SAS controller card.

• Optional remote access controller for remote systems management.

This option requires a riser card with support for PCI-X and PCIe RAC

connectors.

• Optional USB flash drive emulates a diskette drive or hard drive.

• One 345-W power supply.

4 Getting Started Guide

• Two integrated Gigabit Ethernet network adapters, capable of supporting

10-Mbps, 100-Mbps, and 1000-Mbps data rates.

• Two system cooling fans, one power-supply cooling fan, and one optional

PCI fan for systems with a SAS/RAID controller.

• Serial connector for console redirection support.

• Security features, including chassis-intrusion detection and keylock on

the optional bezel.

• Systems management software/circuitry that monitors critical system

voltages and temperatures.

• Back-panel connectors include keyboard, video, mouse, serial, two USB,

and two NIC connectors.

• Front-panel connectors include one VGA and two USB connectors. For

more information about specific features, see "Technical Specifications"

on page 11.

The following software is included with your system:

• A System Setup program for viewing and changing system configuration

information. For more information, see "Using the System Setup Program"

in the

Hardware Owner’s Manual

.

• Enhanced security features, including a system and setup passwords are

available through the System Setup program.

• Video drivers for displaying application programs in high-resolution

modes.

• Systems management software and documentation CDs.

Getting Started Guide 5

Supported Operating Systems

• Microsoft

®

Windows Server

®

2008 Web, Standard, and Enterprise

(32-bit x86) Editions (

when available

)

• Microsoft Windows Server 2008 Web, Standard, Small Business Server

(Premium and Standard), and Enterprise (x64) Editions (

when available

)

• Microsoft Windows Server 2003 Web, Standard, Small Business Server

(Premium and Standard), and Enterprise (32-bit x86) Editions

(SP1 and SP2)

• Microsoft Windows Server 2003 Standard and Enterprise (x64) Editions

• Microsoft Windows Server 2003 R2 Standard, Small Business Server

(Premium and Standard), and Enterprise (32-bit x86) Editions

• Microsoft Windows Server 2003 R2 Standard and Enterprise (x64)

Editions

•Red Hat

®

Enterprise Linux ES (versions 4 and 5) (x86_32)

• Red Hat Enterprise Linux ES (versions 4 and 5) (x86_64)

•SUSE

®

Linux Enterprise Server 9 (SP2 or later) (x86_64)

• SUSE Linux Enterprise Server 10 (x86_64)

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and

regulatory information. Warranty information may be included within this

document or as a separate document.

• The

Rack Installation Instructions

or

Rack Installation Guide

included

with your rack solution describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components. The

Hardware Owner’s Manual

is available

on the CDs that came with your system or on

support.dell.com

.

• CDs included with your system provide documentation and tools

for configuring and managing your system.

• Systems management software documentation describes the features,

requirements, installation, and basic operation of the software.

6 Getting Started Guide

• Operating system documentation describes how to install (if necessary),

configure, and use the operating system software.

• Documentation for any components you purchased separately provides

information to configure and install these options.

• Updates are sometimes included with the system to describe changes

to the system, software, and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates

first because they often supersede information in other documents.

• Release notes or readme files may be included to provide last-minute

updates to the system or documentation or advanced technical reference

material intended for experienced users or technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does

not perform as expected, see your Hardware Owner’s Manual.

Dell Enterprise Training and Certification is available; see

www.dell.com/training for more information. This service may not be offered

in all locations.

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety

instructions and important regulatory information in your Product Information

Guide.

CAUTION: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

This section describes the steps to set up your system for the first time.

Getting Started Guide 7

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

Installing the Rails and System in a Rack

Once you have read the "Safety Instructions" located in the rack

installation documentation for your system, install the rails and

the system in the rack.

See your rack installation documentation for instructions on installing

your system in a rack.

8 Getting Started Guide

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating

which cable to plug into each connector. Be sure to tighten the screws

(if any) on the monitor's cable connector.

Getting Started Guide 9

Connecting the Power

Connect the system’s power cable(s) to the system. Attach the cable

retention clip to the back of the system, run the cable through the cable

retention clip as shown, and close the clip.

Plug the other end of the cable into a grounded electrical outlet or a

separate power source such as an uninterrupted power supply (UPS)

or a power distribution unit (PDU).

10 Getting Started Guide

Turning on the System

Turn on the system and monitor (optional).

Press the power button on the system and the monitor. The power

indicators should light. Adjust the monitor’s controls until the displayed

image is satisfactory.

Installing the Bezel

Install the bezel (optional).

Getting Started Guide 11

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the documentation that came with your operating system.

Be sure the operating system is installed before installing hardware or software

not purchased with the system.

Technical Specifications

Processor

Processor type One Intel

®

Celeron

®

processor

or

One

Intel Core

™

2 Duo

processor

or

One Intel Pentium

®

Dual-Core processor

or

Dual-Core Intel Xeon

®

3000 Sequence processor

or

Quad-Core Intel Xeon 3200 Sequence processor

Front-side bus speed

Intel Celeron

800 MHz minimum

Intel Pentium Dual-Core

800 MHz minimum

Intel Core 2 Duo

800 MHz minimum

Dual-Core Intel Xeon 3000

Sequence

1333 MHz minimum

Quad-Core Intel Xeon 3200

Sequence

1066 MHz minimum

Internal cache

Intel Celeron

512 KB

Intel Pentium Dual-Core

at least 1 MB

Intel Core 2 Duo

at least 2 MB

Dual-Core Intel Xeon 3000

Sequence

4MB Minimum

Quad-Core Intel Xeon 3200

Sequence

2x4MB (8MB) Minimum

12 Getting Started Guide

Expansion Buses

Bus type PCI-X, PCIe

Expansion slots - Two optional riser cards

Riser 1

PCIe

One full-height, half-length, x8 lane PCIe slot

PCIe

One full-height, half-length, x4 lane PCIe slot

residing on a x8 lane connector

Riser 2

PCI-X

One full-height, half-length,

64-bit, 133MHz PCI-X slot

PCIe

One full-height, half-length, x8 lane PCIe slot

Memory

Architecture Up to four unbuffered DDR2 677/800 MHz

SDRAM memory modules with ECC

Memory module sockets Four 240-pin

Memory module capacities 512 MB, 1 GB, or 2 GB

Minimum RAM 512 MB (one 512-MB module)

Maximum RAM 8 GB

Drives

Hard Drives

SATA

Up to two 1-inch high drives

SAS

Up to two optional internal 1-inch high drives

with optional SAS controller card

Optical drive DVD, or combination CD-RW/DVD in a

peripheral drive bay

NOTE: DVD devices are data only.

USB flash drive One optional drive that emulates a diskette drive

or hard drive

Getting Started Guide 13

Connectors

Externally accessible

Back

Network adapter

Two RJ-45 (for integrated 1-Gigabit network

adapters)

PS/2-style keyboard

6-pin mini-DIN

PS/2-compatible mouse

6-pin mini-DIN

Serial

9 pin

USB

Two 4-pin, USB 2.0 compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0 compliant

Internally accessible

SATA channels

Three 7 pin

Video

Video type Integrated ATI ES1000 VGA controller

Video memory 32MB DDR II

Power

AC power supply

Wattage

345 W

Voltage

100–240 VAC, 50/60 Hz

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 25 A for 10 ms or less.

System battery CR 2032 3.0-V lithium coin cell

14 Getting Started Guide

Physical

Height 4.2 cm (1.68 in)

Width 44.6 cm (17.6 in)

Depth

With optional bezel

57.6 cm (22.7 in)

Without optional bezel

54.6 cm (21.5 in)

Weight (maximum configuration) 11.8 kg (26 lb)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 G at 5–350 Hz for 15 min

Storage

1.54 G at 10–250 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 31 G for up to

2.6 ms

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Dell™ PowerEdge™

R200 系统

系统使用入门

注、注意和警告

注：“注”表示可以帮助您更好地使用计算机的重要信息。

注意：“注意”表示可能会损坏硬件或导致数据丢失，并告诉您如何避免

此类问题。

警告：“警告”表示可能会出现导致财产损失、人身伤害甚至死亡的情况。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

、

DELL

徽标和

PowerEdge

是

Dell Inc.

的商标；

Intel

、

Pentium

和

Celeron

是

Intel Corporation

的注册商标而

Core

是

Intel Corporation

的商标；

Microsoft

、

Windows

和

Windows Server

是

Microsoft Corporation

在美国和

/

或其它国家

/

地区的商标或

注册商标；

Red Hat

是

Red Hat, Inc.

的注册商标；

SUSE

是

Novell Inc.

在美国和其它国家

/

地区的注册商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。

型号

SVP

2007

年

8

月

P/N NM215 Rev. A00

系统使用入门 17

系统配置

系统的主要硬件和软件配置包括：

•

支持静态滑轨和滑动滑轨的

1U/1S

机架可固定机箱。

注：使用系统设置程序可以查看处理器信息。请参阅《硬件用户手册》

中的“使用系统设置程序”。

•

以下处理器之一：

–

Intel

®

Celeron

®

–

Intel Pentium

®

Dual-Core™

–

Intel Core 2 Duo™

–

双核

Intel Xeon

®

处理器

3000

系列

–

四核

Intel Xeon

处理器

3200

系列

•

至少

512 MB

的

667 MHz

或

800 MHz DDR2 SDRAM

内存，通过在系

统板上的四个内存模块插槽中安装

512 MB

、

1 GB

或

2 GB

非缓冲

ECC

内存模块组合，最多可升级至

8GB

。

•

以下提升卡选件之一：

–

一个全高、半长、

x8

信道

PCIe

扩充槽和一个全高、半长

PCIe

扩

充槽（带

x8

连接器，但支持

x4

信道）。

–

一个全高、半长、

133MHz/64

位

PCI-X

扩充槽和一个全高、半长、

x8

信道

PCIe

扩充槽，其中包括一个用于连接可选远程访问控制器

(RAC)

卡的连接器。

•

一个

3.5

英寸

CD

、

DVD

或组合

CD-RW/DVD

（位于外围设备驱动器

托架中）。

•

支持以下内部硬盘驱动器配置：

–

通过集成的驱动器控制器，最多可支持两个内部

1

英寸高

SATA

硬

盘驱动器。

–

通过可选的

SAS

控制器卡，最多可支持两个内部

1

英寸高可选串行

连接

SCSI (SAS)

硬盘驱动器。

•

可选的远程访问控制器（用于远程系统管理）。此选项需要支持

PCI-X

和

PCIe RAC

连接器的提升卡。

18 系统使用入门

•

可选的

USB

快擦写驱动器，可以仿真软盘驱动器或硬盘驱动器。

•

一个

345 W

电源设备。

•

两个集成千兆位以太网网络适配器，可以支持

10 Mbps

、

100 Mbps

和

1000 Mbps

数据速率。

•

两个系统冷却风扇、一个电源设备冷却风扇，以及一个可选的

PCI

风扇（用于具有

SAS/RAID

控制器的系统）。

•

串行连接器（用于支持控制台重定向）。

•

安全保护功能部件，包括机箱防盗检测功能和可选挡板上的键锁。

•

系统管理软件

/

电路（用于监测系统临界电压和温度）。

•

背面板连接器包括键盘连接器、视频连接器、鼠标连接器、

串行连接器、两个

USB

连接器和两个

NIC

连接器。

•

前面板连接器包括一个

VGA

连接器和两个

USB

连接器。

有关特定配置的详细信息，请参阅第

24

页的“技术规格”。

您的系统附带以下软件：

•

系统设置程序，用于查看和更改系统配置信息。有关详情，

请参阅《硬件用户手册》中的“使用系统设置程序”。

•

增强型安全保护功能，包括系统和设置密码，可通过系统设置程序进

行设置。

•

视频驱动程序，可使用高分辨率模式显示应用程序。

•

系统管理软件和说明文件

CD

。

ページを読み込んでいます...

Dell PowerEdge R200 クイックスタートガイド

関連論文