GH150E

Kinco GH150E ユーザーマニュアル

  • Kinco GH150E/GL150E人機インターフェースのインストール説明書についてご質問にお答えします。この説明書では、電源接続方法、様々なインターフェース(SDカード、USB、COMポート、イーサネット)の使用方法、そして設置に関する重要な注意事項などが説明されています。ご不明な点がございましたら、お気軽にご質問ください。
  • 電源電圧は何ですか?
    GH150EとGL150Eの違いは何ですか?
    推奨される取り付けトルクは?
    COM0とCOM2はどのような通信プロトコルをサポートしていますか?
dingh
1.1 环境要求
工作环境温度:GH150E/GL150E 人机界面的设计规范可以保证它能够在 14
~131 ℉ ( -10~55 ℃)的大多数工业环境中稳定工作。NEMA 防护规定:
GH150E/GL150E 人机界面的前面板符合 NEMA1 防护规定。
1.2 电源要求
输入电压:DC21V~DC28V
特别需要注意与变频调速器和开关电源供应器保持较远的距离,这类设备的
输入和输出电缆都必须采用屏蔽电缆,并将屏蔽网接到系统的星形接地点;
直流电源必须与交流主电源正确的隔离开;
不要让 GH150E/GL150E 人机界面和感性负载或控制器的输入电路共用电源。
注意:产品内部的快速熔丝在电源电压过高的时候可以起到保护作用并不
能够确保内部电子元件不被损坏。
2.1 尺寸图
注:GL150E 前面板上没有指示
2.2 固定螺钉安装说
将产品放入机器设备控制面板上已开好的安装孔中,从控制面板背面将安装卡
扣卡入 HMI 壳体上的安装方孔中,然后拧紧螺钉推荐扭力0.5N.m(以达到防水、
防尘效果及避免外壳变形)。
2.3 电源连接
在连接电源前,请确认符合所有当地和国家的电气标准。源线缆请选择耐压
值和电流值符合安全规定的线缆。
将产品背面接线端子的螺丝按逆时针方向旋松,插入电电缆,后顺时针拧
紧接线端子的螺丝注意:电源的正极接到标有‘DC24V’的端子上,直流的地
接到标有‘GND’的端子,地线接到标有‘FG’的端子上
3.1 电源端子(后壳)
3.2 SD 卡接口(后壳)(GH150E 支持)
连接
标准 SD 卡(24mm×32mm×2.1mm接口
端口作用
通过此接口插入 SD 卡进行数据拷贝存储以及程序上传/下载
3.3 USB HOST 接口
连接
连接 USB 接口设备或 U 盘
端口
作用
连接 USB 接口键盘、鼠标、打印机等,插入 U 盘上传/下载程序
以及存储数
3.4 USB SLAVE 接口
接口类型是 MicroUSB
3.5 COM0/COM2
COM0/COM2 是 9 针 D 型注意:COM0 支
RS232/485/422 通讯功能,一个串口同时只能支持一种协议
COM2 只支持 RS232 通讯功能
3.6 COM1/COM3(GH150E 支持)
COM1/COM3 是 9 针 D 型注意:COM1 支
RS232/485/422 通讯功能,一个串口同时只能支持一种协议
COM3 只支持 RS485 通讯功能
3.7 以太网接口
10M/100M 自适应以太网 RJ45 端口。
连接
采用五类 UTP 网线与带网口的设备连接
端口
作用
用于 HMI 组态的上/下载,系统参数的设置和在线模拟;成多 HMI
联机;与 PLC 等通过以太网通讯;通过以太网口与 PC 机通讯
《人机界面售后服务条款》请登录如下网址查看http://www.kinco.cn
序号
1
2
3
连接
通过一条通用的 USB 通讯电缆和 PC 机连接
端口作用
上/下载用户组态程序和设置 HMI 系统参数
管脚
信号
PLC (COM0)
[RS-422]
PLC(COM0)
[RS-485]
PLC (COM0
[RS-232]
PC/PLC
(COM2)
[RS-232]
1
Rx-(B)
RS422 R-
RS485 B
2
RxD_PLC
RS232 RxD
3
TxD_PLC
RS232 TxD
4
Tx-
RS422 T-
5
GND
信号地
6
Rx+(A)
RS422 R+
RS485 A
7
RxD_PC
RS232 RxD
8
TxD_PC
RS232 TxD
9
Tx+
RS422 T+
管脚
信号
COM1
[RS-422]
COM1
[RS-485]
COM1
[RS-232]
COM3
[RS-485]
1
Rx-(B)
RS422 R-
RS485B
2
RxD_PLC
RS232 RxD
3
TxD_PLC
RS232 TxD
4
Tx-
RS422 T-
5
GND
信号地
6
Rx+(A)
RS422 R+
RS485A
7
Rx-(B)
RS485B
8
Rx+(A)
RS485A
9
Tx+
RS422 T+
4.后服
GH150E/GL150E 人机界面
安 装 说
深圳市步电气有限公司
电话:0755-26585555
传真:0755-26616372
技术支持热线:400-700-5281
http//www.kinco.cn Emailsales@kinco.cn
步科官方微地址:圳市南山区高新科技园北区朗山一路 6 号一栋
1.装注意事
在以下场所使用时请采取屏
蔽措施:
有静电或其它形式噪音
有较强电磁场的场
可能暴露于射线的场所
靠近于动力电源的场所
请勿在以下场所使用
阳光直射处
周围温度和相对湿度超出规格的场所
温度急剧变化易引起结露的场
有腐蚀性气体和可燃性气体的场所
尘埃、灰尘、盐分、铁粉较多的场所
会被溅到水、油、药品等飞沫的场所
给主机带来直接振动和冲击的场所
2.品安
3.部接
PLC1.ir
1.1 Environmental Requirement
Operating temperature: GH150E/GL150E HMI can work stably in most industrial environments that the
temperature between 14°F to13F (-10~55°C).
NEMA rating: This Series HMI frontpanel is NEMA 1 rated.
1.2 Power Requirement
Input voltage:DC21VDC28V.
Particularly note that there must be enough distance between this product and converters or switch
mode power supply. Make sure that the input and output cables of that kind equipment are shield
cable and the shielding network is connected with the ground.
Make sure that the DC power and AC power is isolated.
Do not use common power with perceptual load or input circuit of the controller.
Note: An Internal fuse will prevent damage for over voltage condition, however it isn’t guaranteed the
internal electronic components are not damaged.
2.1Dimensional Drawing
Note: there is no indicator on the front panel of GL150E.
2.2 Fixed Screw Installation Instructions
The product is put into the well mounted hole of the machine control box’s panel, and the mounting
screws are inserted into the fixing holes around the HMI shell from the back of the control box’s panel.
Recommended lock torque: 0.5N.m (to waterproof effect and avoid shell deformation)
2.3 Power Connection
Before connecting the power, please make sure all local and national electrical standards are met.For
power cables,please select cables with their dielectric strength values and current values in compliance
with the safety specifications.
First find the power terminal at the back of the product and loosen the screw according to
counterclockwise, then insert the power cables and tighten the screw up.
Connect positive DC line to the ‘DC24V terminal, the DC ground to the ‘GND’ terminal and the ground
line to the ’FG’ terminal.
3.1 POWERBack-shell
3.2 SD CARDBack-shell(Only GH150E support)
Connection
Standard SD card interface
Port
Function
The SD Card can be inserted in through this interface for Data storage and user
configuration uploading/downloading.
3.3 USB HOST
Connection
Connect with USB interface devices or U disks
Port
Function
This interface can be connected with USB keyboard, mouse and printers, and the
U disk can be used for user’s configuration uploading/ downloading as well as
data storage.
3.4 USB SLAVE
The interface type is MicroUSB
3.5 COM0/COM2
Pin assignment of the 9-pin male, D-SUB, COM0/COM2.Note:
RS232/485/422 communication functions are supported by COM0.COM2
supports RS232 communication function.
3.6 COM1/COM3(Only GH150E support)
Pin assignment of the 9-pin male, D-SUB, COM1/COM3.Note:
RS232/485/422 communication functions are supported by COM1.COM3
supports RS485 communication function.
3.7 Ethernet
10M/100M adaptive Ethernet RJ45 port.
Connection
With CAT5 UTP cable connected to the Ethernet device.
Port
Function
The port can be used for upload/download of HMI configuration, setting of
system parameters and online simulations of configurations. It can connect
multiple HMIs via the Ethernet to form an HMI network. Furthermore, it can
implement communications between HMI and PLC via the Ethernet, as well
as communications with a PC via the Ethernet port.
For < Service Terms and Conditions for HMI >, please check:http://www.kinco.cn
Pin#
1
2
3
Connection
USB Slave port can be connected with a PC
Port
Function
The port is only used to download user configuration program to the HMI and to
set HMI system parameters.
Pin
Signal
PLC (COM0
[RS-422]
PLC(COM0
[RS-485]
PLC (COM0
[RS-232]
PC/PLC
COM2
[RS-232]
1
Rx-(B
RS422 R-
RS485 B
2
RxD_PLC
RS232 RxD
3
TxD_PLC
RS232 TxD
4
Tx-
RS422 T-
5
GND
Signal ground
6
Rx+(A)
RS422 R+
RS485 A
7
RxD_PC
RS232 RxD
8
TxD_PC
RS232 TxD
9
Tx+
RS422 T+
Pin
Signal
COM1
[RS-422]
COM1
[RS-485]
COM1
[RS-232]
COM3
[RS-485]
1
Rx-(B)
RS422 R-
RS485 B
2
RxD_PLC
RS232 RxD
3
TxD_PLC
RS232 TxD
4
Tx-
RS422 T-
5
GND
Signal ground
6
Rx+(A)
RS422 R+
RS485 A
7
Rx-(B)
RS485B
8
Rx+(A)
RS485A
9
Tx+
RS422 T+
GH150E /GL150E HMI
Installation Instruction
Kinco Electric (Shenzhen) Ltd.
AddBuilding 1, No. 6 Langshan 1st Rd, Hi-tech Park North, Nanshan, Shenzhen, China.
Tel0755-26585555 Fax0755-26616372http//www.kinco.cn Emailsales@kinco.cn
1.Installation Note
Pleasetakeshielding
measures in the following
places:
Places that exist
electrostatic or other kinds
of noise
Places of strong
electromagnetic
Places that may be exposed
to rays
Places near the power
Please do not use in the following places:
Places direct in sunlight
Surroundingtemperature and humidity beyond the
specifications
Places of temperature changes sharply and easily
cause condensation
Places that exist corrosive gas and combustible
gas
Places of much dust, dirt, salt and iron powder
Places that will be splashed water, oil and drugs
Places that bring direct vibration and shock to
2.Installation Description
3.External Interface
4.After-sales Service
PLC1.ir
/