RayRun N11 ユーザーマニュアル

タイプ
ユーザーマニュアル

RayRun N11は、ワイヤレスリモコンで操作できる単色LED調光器です。

機能

  • 100段階の調光機能
  • 6段階の調光プリセット機能
  • メモリー機能(前回の設定を記憶し、電源ON時に自動で復元)
  • 過負荷保護機能
  • 過熱保護機能
  • 省エネ設計

使用例

  • 自宅の照明の調光
  • 店舗やオフィスの照明の調光
  • イベントや展示会の照明の調光
  • 看板の照明の調光

RayRun N11は、使いやすく、機能的な単色LED調光器です。幅広い用途に使用することができ、省エネにも貢献します。

RayRun N11は、ワイヤレスリモコンで操作できる単色LED調光器です。

機能

  • 100段階の調光機能
  • 6段階の調光プリセット機能
  • メモリー機能(前回の設定を記憶し、電源ON時に自動で復元)
  • 過負荷保護機能
  • 過熱保護機能
  • 省エネ設計

使用例

  • 自宅の照明の調光
  • 店舗やオフィスの照明の調光
  • イベントや展示会の照明の調光
  • 看板の照明の調光

RayRun N11は、使いやすく、機能的な単色LED調光器です。幅広い用途に使用することができ、省エネにも貢献します。

N11 single color LED dimmer is designed to drive
constant voltage LED products in voltage range of DC5-
24V. The main unit works with a RF remote controller, user
can adjust LED brightness on the remote controller. The
main unit is powered by DC power supply and receives
remote controller commands to drive LED fixtures.
Single Color LED Dimmer
Wireless Remote Control
Full Protection High Power
Wireless Remote
Easy Operation Compact Size
Wide Voltage Range
1. Power supply input
Install positive power cable into the terminal marked
with ‘+’ and negative power cable into the terminal marked
with ‘-’. The controller can accept DC power from 5V to
24V, the output voltage is the same as the power supply, so
please make sure the LED rated voltage is same as the
power supply.
Do not power on the controller until all connection is
firmly finished.
2. LED output
Connect LED fixtures to this terminal. Install positive
LED load cable into the terminal marked with ‘+’ and
negative cable into the terminal marked with ‘-’. Please
make sure the LED rated voltage is same as the power
supply and the maximum load current is lower than
controller’s rated current.
The controller will run into protection if the output is
overloaded or short circuited. The indicator will flash red
color and stop working in this case, Please check the
wiring and load current to remove the fault.
3. Work status indicator
This indicator displays all working status of the
controller. It shows different events as following:
Steady green: Normal working.
Single green blink: Command received.
Long single green blink: Mode or color cycle edge.
Long single yellow blink: Brightness or speed limit.
Red flash: Overload protection.
Yellow flash: Over heat protection.
Green flash 3 times: New remote controller paired.
7
4
5
6
4. Turn ON / OFF
Press ‘I’ key to turn on unit or press ‘O’ key to turn off.
Main unit will memorize the on/off status and will restore
to the previous status on next power on.
Please use remote controller to turn on the unit if it
was switched to off status before previous power cut.
5. Brightness control
Press ‘+’ key to increase brightness and press ‘-’ key
to decrease. The brightness will change smoothly when
hold pressing these two keys.
The controller applies brightness gamma correction on
dimming control, makes the brightness tuning more
smooth to human sense.
6. Brightness shortcut keys
87mm
24mm
72mm
1 2
3
These keys are shortcuts to fixed brightness. Press
each key to jump to the relevant brightness level.
The controller applies brightness gamma correction on
dimming, the brightness level is valued to human sense,
and not proportional to the LED output power.
80%100% 60%
20%40% 10%
Model: N11
IntroductionIntroduction
Dimension
Wiring & Indicator
11
Functions
2 3
5
Model
N11
Brightness grade
100 levels
Brightness shortcut
6 levels
PWM grade
4000 steps
Overload protection
Yes
Overheat protection
Yes
Working voltage
DC 5-24V
Remote frequency
433.92MHz
Remote control distance
>15m at open area
Rated output current
1x10A
Controller dimension
87x24x15mm
7. Remote indicator
8. Using the remote
Please pull out the battery insulate tape before using. The
RF wireless remote signal can pass through some nonmetal
barrier. For proper receiving remote signal, please do not install
the controller in closed metal parts.
9. Pair a new remote controller
The remote controller and main unit is 1 to 1 paired for
factory default. Its possible to pair maximum 5 remote
controllers to one main unit and each remote controller could
be paired to any main unit.
You could pair a new remote controller to main unit by
following steps:
1). Plug off the power of main unit and plug in again after
more than 5 seconds.
2). Press ‘100%’ and ‘60%’ key simultaneously for about 3
seconds, within time of 10 seconds after the main unit powered
on.
10. Recognize current remote only
11. Protection
The main unit has full protection function for wrong
wiring, output short circuit, overload and overheat. The
controller will protect itself from damage at these extreme
conditions and could automatically recover when working
condition is good.
To avoid the protection, please ensure the LED fixtures
are capable for constant voltage driving and in rated range,
the cables are well connected and insulated. Also please
install the controller with good ventilation and heat
dissipation condition.
In some cases, one main unit might be paired with
several remote controllers but extra remote controllers are
no longer needed. User could simply pair the current
using remote to main unit again, then the main unit will
dis-pair all other remote controllers and recognize current
one only.
This indicator blinks when remote controller is
working. If the indicator flash slowly when pressing keys, it
means the remote battery is nearly empty and please
change the battery in this case. The battery model is
CR2032.
Operation
14 15
Specification
16
N11LED5V
24VLED品,
LED控电,
LED具,
7
4
5
6
5.亮
“+”度,“-”
理,使
滑,
80%100% 60%
20%40% 10%
11
:N11
2 3
⾊LED控
RF⽆线遥控器
全功能保护 高功率
无线遥控
简易操作 小尺寸
宽电压输入
1.电
接线及指⽰灯
控制器可接受电压为5V24V电,
线“+”⼦,线
“-”控
同,LED同,
全,
2.LED
3.状
态,
绿
绿
绿
绿烁3
4./
I光,O”
态,态,使
6.亮
理,
别,
87mm
24mm
72mm
1 2
3
LED将LED
“+”中,“-
请确保LED同,
况,
此作,
线
1对11
5器,
器,
1)源,5
2)10内,
100%60%3
后,3
14 15
16
7.遥
8.使
使⽤前请拔出遥控器电池绝缘⽚。RF线
穿
果,
9.与
11.保
能,
线
当时,作,
时,
时,态,
红⾊闪烁
⾼,PWM
⻩⾊闪烁
10.保
对,
下,使
作,
使
N11
100
6
PWM
4000
DC5-24V
遥控器⼯作频率
433.92MHz
遥控器⼯作距离
>15
1x10A
87x24x15mm
时,如
闪,尽,
CR2032
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

RayRun N11 ユーザーマニュアル

タイプ
ユーザーマニュアル

RayRun N11は、ワイヤレスリモコンで操作できる単色LED調光器です。

機能

  • 100段階の調光機能
  • 6段階の調光プリセット機能
  • メモリー機能(前回の設定を記憶し、電源ON時に自動で復元)
  • 過負荷保護機能
  • 過熱保護機能
  • 省エネ設計

使用例

  • 自宅の照明の調光
  • 店舗やオフィスの照明の調光
  • イベントや展示会の照明の調光
  • 看板の照明の調光

RayRun N11は、使いやすく、機能的な単色LED調光器です。幅広い用途に使用することができ、省エネにも貢献します。

他の言語で