DeWalt DCS310 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
DCS310
2
Copyright DeWALT
English (original instructions) 04
14
中文(繁體) 24
34
1
a
d
b
c
f
k
j
g
h
e
i
Figure 1
Figure 2
j
Figure 3
b
2
Figure 5
Figure 4
c
k
j
Figure 6
Figure 7
Figure 8
3
f
e
g
Figure 9A
Figure 10 Figure 11
Figure 12 Figure 13A
Figure 13B
Figure 9B
Figure 9C
English
4
10.8V CORDLESS PIVOT RECIPROCATING SAW
DCS310
Congratulations!
You have chosen a DeWALT tool. Years of
experience, thorough product development and
innovation make DeWALT one of the most reliable
partners for professional power tool users.
Technical Data
DCS310
Voltage V
DC
10.8
Type 1
Battery Type Li-Ion
Max. power output W 140
No-load speed min
-1
0–2700
Stroke length mm 14.3
Weight (without battery pack) kg 1.2
Battery pack DCB121 DCB123
Battery type Li-Ion Li-Ion
Voltage V
DC
10.8 10.8
Capacity A
h
1.3 1.5
Weight kg 0.2 0.2
Charger DCB100 DCB105
Mains voltage V
AC
220-240 220-240
Battery type Li-Ion Li-Ion
Approx. min 40 40 30 30
charging (1.3 Ah (1.5 Ah (1.3 Ah (1.5 Ah
time battery battery battery battery
packs) packs) packs) packs)
Weight kg 0.3 0.49
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not
avoided, will result in death or serious
injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
Save all warningS and inStructionS
for future reference
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
English
5
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
English
6
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Safety Instructions for
Reciprocating Saws
• Hold power tool by insulated gripping
surfaces when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
“live” wire will make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
• ALWAYSwearadustmask.Exposure to
dust particles can cause breathing difficulty and
possible injury.
• NEvER switch on the tool when the saw blade
is jammed in the workpiece or in contact with
the material.
• Keephandsawayfrommovingparts. Never
place your hands near the cutting area.
• Useextracautionwhencuttingoverhead
andpayparticularattentiontooverhead
wireswhichmaybehiddenfromview.
Anticipate the path of falling branches and
debris ahead of time.
• Do not operate this tool for long periods of
time. Vibration caused by the operating action
of this tool may cause permanent injury to
fingers, hands, and arms. Use gloves to provide
extra cushion, take frequent rest periods, and
limit daily time of use.
SWITCHING ON AND OFF
• Afterswitchingoff,neverattempttostopthe
saw blade with your fingers.
• Neverputthesawdownonatableorwork
bench unless switched off. The saw blade will
keep running briefly after the tool has been
switched off.
WHEN SAWING
• Whenusingsawbladesspeciallydesignedfor
cutting wood, remove all nails and metal objects
from the workpiece before starting work.
• Whereverpossible,useclampsandvicesto
fasten the workpiece securely.
• Donotattempttosawextremelysmall
workpieces.
• Donotbendtoofarforward.Makesure
that you always stand firmly, particularly on
scaffolding and ladders.
• Alwaysholdthesawwithbothhands.
• Forcuttingcurvesandpockets,useanadapted
saw blade.
CHECKING AND CHANGING THE SAW BLADE
• Onlyusesawbladesconformingtothe
specifications contained in these operating
instructions.
• Onlysharpsawbladesinperfectworking
condition should be used; cracked or bent saw
blades should be discarded and replaced at
once.
• Ensurethatthesawbladeissecurelyfixed.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of personal injury due to flying particles.
Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
DATE CODE POSITION
The date code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
Example:
2012 XX XX
Year of Manufacture
English
7
Important Safety Instructions for All
Battery Chargers
SAVETHESEINSTRUCTIONS: This manual
contains important safety and operating instruc tions
for the DCB100 and DCB105 battery chargers.
• Beforeusingcharger,readallinstructionsand
cautionary markings on charger, battery pack,
and product using battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeablebatteries.Othertypesof
batteries may burst causing personal
injury and damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions, with
the charger plugged in to the power
supply, the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, grinding dust, metal chips,
steel wool, aluminum foil, or any buildup
of metallic particles should be kept away
from charger cavities. Always unplug the
charger from the power supply when
there is no battery pack in the cavity.
Unplug charger before attempting to
clean.
• DONOTattempttochargethebatterypack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• Thesechargersarenotintendedfor
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Donotexposechargertorainorsnow.
• Pullbyplugratherthancordwhen
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Makesurethatcordislocatedsothatit
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Donotuseanextensioncordunlessit
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
• Donotplaceanyobjectontopofcharger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of the housing.
• Donotoperatechargerwithdamagedcord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
service centre.
• Donotdisassemblecharger;takeittoan
authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• Incaseofdamagedpowersupplycordthe
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnectthechargerfromtheoutlet
beforeattemptinganycleaning.Thiswill
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVERattempt to connect 2 chargers together.
• Thechargerisdesignedtooperateon
standard220-240Vhouseholdelectrical
power. Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
Save tHeSe inStructionS
Chargers
The DCB100 and DCB105 chargers accept 10.8 V
Li-Ion batteries.
These chargers require no adjustment and are
designed to be as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack (j) into the charger.
The red (charging) light will blink continuously
indicating that the charging process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
English
8
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.
Charging Process
Refer the table below for the state of charge of the
battery pack.
State of charge
charging – –
fully charged –––––––––––
hot/cold pack delay –– ––
replacebatterypack •••••••••••
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
LI-ION BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
read all inStructionS
• Donotchargeorusebatteryinexplosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
• Never force battery pack into charger. Do
not modify battery pack in any way to fit into
a non-compatible charger as battery pack
may rupture causing serious personal injury.
• ChargethebatterypacksonlyinDeWALT
chargers.
• DONOTsplash or immerse in water or other
liquids.
• Donotstoreorusethetoolandbattery
pack in locations where the temperature
may reach or exceed 40 ˚C (105 ˚F) (such as
outside sheds or metal buildings in summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged,
do not insert into charger. Do not
crush, drop or damage battery pack.
Do not use a battery pack or charger
that has received a sharp blow, been
dropped, run over or damaged in any
way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock
or electrocution may result. Damaged
battery packs should be returned to
service centre for recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Donotincineratethebatterypackevenifit
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium ion battery packs are burned.
• Ifbatterycontentscomeintocontactwith
the skin, immediately wash area with mild
soap and water. If battery liquid gets into the
eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contentsofopenedbatterycellsmaycause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Battery Pack
BATTERY TYPE
The DCS310 operates on a 10.8 volt battery pack.
Storage Recommendations
English
9
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
2. For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
Read instruction manual before use.
100%
Battery charging.
100%
Battery charged.
Battery defective.
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Use only with DeWALT battery packs,
others may burst, causing personal injury
and damage.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4 ˚C and 40 ˚C.
Discard the battery pack with due care for
the environment.
Do not incinerate the battery pack.
See Technical Data for charging time.
Only for indoor use.
Package Contents
The package contains:
1 Compact reciprocating saw
2 Li-Ion battery packs
1 Charger
1 Kit box
1 Instruction manual
NOTE: Battery packs and chargers are not included
with N-models.
• Checkfordamagetothetool,partsor
accessories which may have occurred during
transport.
• Takethetimetothoroughlyreadand
understand this manual prior to operation.
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Trigger switch
b. Lock-off button
c. Pivot release slider
d. Shoe
e. LED worklight
f. Blade clamp
g. Blade clamp release lever
h. Main handle
i. Hand grip
j. Battery pack
k. Battery pack release button
INTENDED USE
This reciprocating saw is designed for professional
cutting of wood, metal, plastic and drywall.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
This reciprocating saw is a professional power tool.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
English
10
• Thisproductisnotintendedforusebypersons
(including children) suffering from diminished
physical, sensory or mental abilities, or for lack
of experience and/or for want of knowledge or
skills unless they are supervised by a person
responsible for their safety. Children should
never be left alone to play with this product.
Electrical Safety
This tool is double insulated; therefore no
earth wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced
by the manufacturer or an authorised Black &
Decker Service Centre in order to avoid a hazard.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: Prior to assembly and
adjustment, always remove the battery
pack. Always switch off the tool before
inserting or removing the battery pack.
WARNING: Use only DeWALT battery
packs and chargers.
Installing and Removing the Battery
Pack (fig. 5)
WARNING: To reduce the risk of injury,
never depress the battery release button
without removing the battery pack.
Depressing the battery release button
without removing the battery pack can
result in the battery pack falling out
unexpectedly.
NOTE: Make sure your battery pack (j) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack with the rails inside the
handle.
2. Slide it firmly into place until you hear the lock
snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release button (k) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
Variable Speed Trigger Switch (fig.1)
To turn the tool on, squeeze the variable speed
trigger switch (a). To turn the tool off, release the
variable speed trigger switch.
The trigger switch enables you to start the
application at a slow speed. The further you depress
the trigger, the faster the tool will operate.
WARNING: This tool has no provision
to lock the switch in the on position and
should never be locked on by any other
means.
LOCK-OFF BUTTON
Your saw is equipped with a lock-off button (b).
To lock the trigger switch (a), press the lock-off
button as shown in figure 3. When the lock-off
button is depressed to the lock icon, the tool is
locked. Always lock the trigger switch when carrying
or storing the tool to eliminate unintentional starting.
NOTICE: Use of very slow speed is
recommended only for beginning a cut.
Prolonged use at very slow speed may
damage your saw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: Toreducetherisk
of serious personal injury, place
thelock-offbuttoninthelock-
off position or turn tool off and
disconnectbatterypackbefore
makinganyadjustmentsor
removing/installingattachmentsor
accessories. An accidental start-up
can cause injury.
Proper Hand Position (fig. 1, 4)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
English
11
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the
hand grip (i), with the other hand on the main handle
(h). Hand orientation is dependent upon user’s
preference.
Pivot Release Slider (fig. 3, 6, 7)
WARNING: To avoid tool being turned
on accidentally, make sure the lock-off
button (b) is engaged.
WARNING: To avoid being pinched,
keep hands away from the hinge when
changing positions.
The tool can be converted into three different
positions. To change positions, slide the pivot
release slider (c) to the right as shown in Figure6
and rotate the handle portion of the tool until it
snaps securely into any of the three positions shown
in Figure 7.
Blade Installation and Removal
(fig.8, 9A, 9B, 9C)
WARNING: Toreducetherisk
of serious personal injury, place
thelock-offbuttoninthelock-
off position or turn tool off and
disconnectbatterypackbefore
makinganyadjustmentsor
removing/installingattachmentsor
accessories. An accidental start-up
can cause injury.
Different blade lengths are available. Use the
appropriate blade for the application. The blade
should be longer than 3-1/2" (89 mm) and should
extend past the shoe and the thickness of the
workpiece during the cut. A 4" (102 mm) blade is
recommended for best performance. Do not use
jigsaw blades with this tool.
WARNING: Cut hazard. Blade breakage
may occur if the blade does not extend
past the shoe and the workpiece during
the cut (fig.8). Increased risk of personal
injury, as well as damage to the shoe
and workpiece may result.
TO INSTALL BLADE INTO SAW (FIG. 9A, 9B, 9C)
1. Pull blade clamp release lever (g) up.
2. Insert the blade shank into the blade clamp
(f,fig. 9C).
3. Close blade clamp release lever.
4. Note that the blade can be installed upside-
down to assist in flush-to cutting (refer to
fig.9B).
TO REMOVE BLADE FROM SAW (FIG. 9A, 9B, 9C)
CAUTION: Burn hazard. Do not touch
the blade immediately after use. Contact
with the blade may result in personal
injury.
1. Pull blade clamp release lever (g) up.
2. Remove blade.
Worklight (fig. 9C)
The worklight (e) is located below the blade clamp
(f) behind the shoe. The worklight will be activated
when the trigger switch is squeezed.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Cutting (fig. 9B, 10–13)
WARNING: Always use eye protection.
All users and bystanders must wear eye
protection that conforms to ANSI Z87.1.
WARNING: Exercise extra caution
when cutting towards operator. Always
hold saw firmly with both hands while
cutting.
Before cutting any type of material, be sure it is firmly
anchored or clamped to prevent slipping. Place
blade lightly against work to be cut, switch on saw
motor and allow it to obtain maximum speed before
applying pressure. Whenever possible, the saw shoe
must be held firmly against the material being cut.
This will prevent the saw from jumping or vibrating
and minimize blade breakage. Any cuts which put
pressure on the blade such as angle or scroll cuts
increase potential for vibration, kickback and blade
breakage.
WARNING: Use extra caution when
cutting overhead and pay particular
attention to overhead wires which may
be hidden from view. Anticipate the path
of falling branches and debris ahead of
time.
WARNING: Inspect work site for hidden
gas pipes, water pipes or electrical wires
before making blind or plunge cuts.
Failure to do so may result in explosion,
property damage, electric shock, and/or
serious personal injury.
FLUSH-TO CUTTING (FIG. 9B, 10)
The compact design of the saw motor housing and
spindle housing permits extremely close cutting to
English
12
floors, corners and other difficult areas. The blade
should be inserted upside-down to assist in flush-
cutting (fig.9B).
POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 11)
The initial step in pocket cutting is to measure the
surface area to be cut and mark clearly with a
pencil, chalk or scriber. Use the appropriate blade
for the application. The blade should be longer than
3-1/2" (89mm) and should extend past the shoe
and the thickness of the workpiece during the cut.
A 4" (102mm) blade is recommended for best
performance. Insert blade into the blade clamp.
Next, tip the saw backward until the back edge
of the shoe is resting on the work surface and the
blade clears the work surface. Then, squeeze the
trigger switch and allow saw to come up to speed.
Grip saw firmly with both hands and begin a slow,
deliberate upward swing with the handle of the saw,
keeping the bottom of the shoe firmly in contact with
the workpiece. Blade will begin to feed into material.
Always be sure blade is completely through material
before continuing with pocket cut.
NOTE: In areas where blade visibility is limited, use
the edge of the saw shoe as a guide. Lines for any
given cut should be extended beyond edge of cut
to be made.
METAL CUTTING (FIG. 12)
Your saw has different metal cutting capacities
depending upon type of blade used and the metal
to be cut. Use a finer blade for ferrous metals and a
coarse blade for non-ferrous materials. In thin gauge
sheet metals it is best to clamp wood to both sides
of sheet. This will ensure a clean cut without excess
vibration or tearing of metal. Always remember not
to force cutting blade as this reduces blade life and
causes costly blade breakage.
NOTE: It is generally recommended that when
cutting metals you should spread a thin film of oil or
other lubricant along the line ahead of the saw cut
for easier operation and longer blade life.
HORIZONTAL/VERTICAL SAW MODES (FIG. 13)
The saw can be used in either of the modes shown.
Horizontal Mode: Blade teeth face downward as
shown in figure13A.
Vertical Mode: Blade teeth face forward as shown
in figure 13B.
The DCS310 can accept all lengths of reciprocating
blades. For best results use 4" (102 mm) blades.
Ensure the blade extends past the shoe and the
thickness of the workpiece during the cut. Use a
longer blade if needed. Whenever possible, the
saw shoe must be held firmly against the material
being cut. This will prevent the saw from jumping or
vibrating and minimize blade breakage.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: Toreducetherisk
of serious personal injury, place
thelock-offbuttoninthelock-
off position or turn tool off and
disconnectbatterypackbefore
makinganyadjustmentsor
removing/installingattachmentsor
accessories. An accidental start-up
can cause injury
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
English
13
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT, recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DeWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and
packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Runthebatterypackdowncompletely,then
remove it from the tool.
• Li-Ioncellsarerecyclable.Takethemtoyour
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
14
10.8V
DCS310
DCS310
V
DC
10.8
1
140
min
-1
0-2700
mm 14.3
() kg 1.2
DCB121 DCB123
V
DC
10.8 10.8
A
h
1.3 1.5
kg 0.2 0.2
DCB100 DCB105
V
AC
220 V 220 V
40 40 30 30
(1.3 Ah (1.5 Ah (1.3 Ah (1.5 Ah
) ) ) )
kg 0.3 0.49
/
指由市电驱动时(
有线)电动工具,或由电池驱动时(无线)电动工
具。
1)
a)
b)
c)
2)
a)
b)
15
c)
d)
e)
f)
(RCD)
3)
a)
b)
c)
d)
e)
f)
g)
4)
a)
b)
c)
d)
e)
f)
g)
5)
a)
b)
c)
d)
16
e)
6)
a)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2012 XX XX
DCB100
DCB105

17
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
220
DCB100 DCB105 10.8 V
( 2)
1.
2. (j)
3.
18
–– –– –– ––
–––––––––––––––––
/ ––– –– ––– ––
• • • • • • • • • • •
/
•
•
•
•
•
40°C
(
105°F
)
•
•
15
•
DCS310 10.8
1.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

DeWalt DCS310 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

他の言語で