Dell POWEREDGE R710 クイックスタートガイド

Dell™ PowerEdge™

R710 Systems

Getting Started

With Your System

系统使用入门

Memulai Dengan Sistem Anda

はじめに

시스템시작하기

Dell™ PowerEdge™

R710 Systems

Getting Started

With Your System

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.; Citrix and XenServer are trademarks

of Citrix Systems, Inc. and/or more of its subsidiaries, and may be registered in the United States

Patent and Trademark Office and in other countries. Intel and Xeon are registered trademarks of Intel

Corporation in the U.S. and other countries; Microsoft, Hyper-V, Windows, and Windows Server are

either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other

countries. Red Hat and Enterprise Linux are registered trademarks of Red Hat, Inc. in the United States

and other countries; SUSE is a registered trademark of Novell, Inc., in the United States and other

countries. VMware is a registered trademark of VMware, Inc. in the United States and/or other

jurisdictions.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model E02S

December 2008 P/N DP855 Rev. A01

Getting Started With Your System 3

Installation and Configuration

WARNING: Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Rails and System in a Rack

Assemble the rails and install the system in the rack following the safety

instructions and the rack installation instructions provided with your system.

4 Getting Started With Your System

Optional – Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Connecting the Power Cables

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

Getting Started With Your System 5

Securing the Power Cord

Bend the system power cable into a loop as shown in the illustration and

secure the cable to the bracket using the provided strap.

Plug the other end of the power cables into a grounded electrical outlet or

a separate power source such as an uninterruptible power supply (UPS) or

a power distribution unit (PDU).

Turning on the System

Press the power button on the system and the monitor. The power indicators

should light.

6 Getting Started With Your System

Installing the Optional Bezel

Install the bezel (optional).

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the installation and configuration documentation for your

operating system. Be sure the operating system is installed before installing

hardware or software not purchased with the system.

• Citrix

®

XenServer

™

5.0 with hotfix 1 or later

• Microsoft

®

Windows Server

®

2008 Hyper-V

™

• Microsoft Windows Server 2008 Web, Standard, and Enterprise

(32-bit x86) Gold editions

• Microsoft Windows Server 2008 Web, Standard, Enterprise, and

Datacenter (x64) Gold editions

• Microsoft Window Small Business Server 2008, Standard and Premium

(x64) editions.

• Microsoft Windows Server 2003 Web, Standard, and Enterprise

(32-bit x86) editions with SP2

• Microsoft Windows Server 2003 Standard and Enterprise (x64) editions

with SP2

Getting Started With Your System 7

• Microsoft Windows Server 2003 R2 Standard and Enterprise (32-bit x86)

editions with SP2

• Microsoft Windows Server 2003 R2 Standard, Enterprise,

and Datacenter (x64) editions with SP2

• Microsoft Windows Small Business Server 2003 R2 Standard

and Premium editions with SP2

•Red Hat

®

Enterprise Linux

®

ES and AS 4.7 (x86)

• Red Hat Enterprise Linux ES and AS 4.7 (x86_64)

• Red Hat Enterprise Linux 5.2 Server (x86_32)

• Red Hat Enterprise Linux 5.2 Server (x86_64)

• SUSE Linux Enterprise Server 10 SP2 (x86_64)

•VMware

®

ESX Version 4.0 and 3.5, Update 4 (when available)

• VMware ESXi Version 4.0 and 3.5, Update 4 (when available)

NOTE: For the latest information on supported operating systems,

see www.dell.com.

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as

a separate document.

• The rack documentation included with your rack solution describes how to

install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components. This document is available online at

support.dell.com.

• Any media that ships with your system that provides documentation and

tools for configuring and managing your system, including those

pertaining to the operating system, system management software, system

updates, and system components that you purchased with your system.

NOTE: Always check for updates on support.dell.com and read the updates

first because they often supersede information in other documents.

8 Getting Started With Your System

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not

perform as expected, see your Hardware Owner’s Manual. Dell

™

offers

comprehensive hardware training and certification. See www.dell.com/training

for more information. This service may not be offered in all locations.

Información de la NOM (sólo para México)

La información que se proporciona a continuación aparece en el dispositivo

descrito en este documento, en cumplimiento de los requisitos de la Norma

Oficial Mexicana (NOM):

Importador:

Número de modelo: E02S

Voltaje de

alimentación:

100-240 V CA

Frecuencia: 50/60 Hz

Consumo eléctrico: 7,0-3,5 A

Getting Started With Your System 9

Technical Specifications

Processor

Processor type One or two quad- or dual-core Intel

®

Xeon

®

processors

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots via

riser card:

Riser 1 (Center Riser)

One full-height, 9.5-inch length, x4 link (slot 1)

NOTE: This slot can be upgraded to 12.2 inches.

One low-profile, 9.5-inch length, x4 link (slot 2)

Riser 2 (Left Riser)

Two full-height, 9.5-inch length, x8 link (slot 3 and 4)

or

One full-height, 9.5-inch length, x16 link (slot 3)

NOTE: Support for up to 25W is available only on the first

two cards installed in the system; any additional cards

installed in the system must be 15W or under.

Memory

Architecture 800, 1066, or 1333 MHz DDR3 registered or unbuffered

Error Correcting Code (ECC) DIMMs. Support for

Advanced ECC or Memory Optimized operation.

Memory module

sockets

Eighteen 240-pin

Memory module

capacities

1 GB and 2 GB UDIMMs, and 2 GB, 4 GB,

or 8 GB RDIMMs

(single, dual, or quad-rank dependent on capacity)

Minimum RAM 1 GB with a single processor (1 DIMM per processor)

Maximum RAM 96 GB (with quad-rank 8 GB RDIMM), 144 GB

(with dual-rank 8 GB RDIMM), or 24 GB (with 2 GB

UDIMMs)

10 Getting Started With Your System

Drives

Hard drives Up to six 3.5-inch, internal, hot-swappable SAS or SATA

hard drives without optional internal tape drive support

or

Up to four 3.5-inch, internal, hot-swappable SAS or

SATA hard drives with optional internal tape drive support

or

Up to eight 2.5-inch, internal, hot-swappable SAS or

SATA hard drives with optional internal tape drive

support

Diskette Drive Optional external USB 1.44-MB drive

Optical drive One optional internal slimline SATA DVD-ROM or

DVD+RW drive

Optional external USB DVD

NOTE: DVD devices are data only

Internal Tape Drive One optional half-height tape back-up device

Flash Drive Optional internal USB

Optional internal Secure Digital (SD) memory card

Optional external SD memory card

Connectors

Back

NIC

Four RJ-45 10/100/1000 Mbps Ethernet

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Optional external

VFlash card

One flash memory card slot on the back panel

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

One 4-pin, USB 2.0-compliant

Optional internal

SD module

One internal flash memory card slot

Getting Started With Your System 11

Video

Video type Integrated Matrox G200

Video memory 8 MB shared

Power

AC Power Supply (per power supply)

Wattage

870 W (High Output)

570 W /200840 KB (Energy Smart)

Voltage

90–264 VAC, autoranging, 47-63 Hz

Heat dissipation

2968.6 BTU/hr maximum (High Output)

1944.9 BTU/hr maximum (Energy Smart)

Maximum inrush

current

Under typical line conditions and over the entire system

ambient operating range, the inrush current may reach

55 A per power supply for 10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium coin cell

RAID battery

(optional)

3.7-V lithium ion battery pack

Physical

Height 8.64 cm (3.4 in)

Width 48.24 cm (18.99 in) with rack latches

44.31 cm (17.4 in) without rack latches

Depth 72.06 cm(28.4 in) with power supplies and bezel

68.07 cm(26.8) without power supplies and bezel

Weight (maximum

configuration)

26.1 kg (57.54 lb)

Weight (empty) 17.7 kg (39 lb)

12 Getting Started With Your System

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum temperature

gradation of 10°C per hour

NOTE: For altitudes above 2950 feet, the maximum operating

temperature is derated 1°F/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with a maximum temperature

gradation of 20°C per hour

Relative humidity

Operating

20% to 80% (non-condensing) with a maximum humidity

gradation of 10% per hour

Storage

5% to 95% (non-condensing) with a maximum humidity

gradation of 10% per hour

Maximum vibration

Operating

0.26 Gms from 5–350 Hz for 5 minutes in operational

orientations

Storage

1.54 Gms from 10–250 Hz for 10 minutes in all orientations

Maximum shock

Operating

Half sine shock in all operational orientations of 31 G plus

or minus 5% with a pulse duration of 2.6 ms plus or minus

10%

Storage

Half sine shock on all six sides of 71 G plus or minus 5%

with a pulse duration of 2 ms plus or minus 10%

Square wave shock on all six sides of 27 G with a velocity

change at 235 in/sec or greater

Altitude

Operating

–16 to 3,048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet, the maximum operating

temperature is derated 1°F/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Dell™ PowerEdge™

R710 系统

系统使用入门

注、小心和警告

注：“注”表示可以帮助您更好地使用计算机的重要信息。

警告：

“警告”表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式复制这些材料。

Dell

、

DELL

徽标和

PowerEdge

是

Dell Inc.

的商标；

Citrix

和

XenServer

是

Citrix Systems, Inc.

和

/

或其多个子公司的商标，并可能已在美国专利商标局和其它国家和地区注册。

Intel

和

Xeon

是

Intel Corporation

在美国

和其它国家和地区的注册商标；

Microsoft

、

Hyper-V

、

Windows

和

Windows Server

是

Microsoft Corporation

在美国和

/

或其它国家

/

地区的商标或注

册商标。

Red Hat

和

Enterprise Linux

是

Red Hat, Inc.

在美国和其它国家和地区的注册商标；

SUSE

是

Novell, Inc.

在美国和其它国家和地区的注册商标。

VMware

是

VMware, Inc.

在美国

和

/

或其它管辖区域的注册商标。

本说明文件中述及的其它商标和产品名称是指拥有相应商标和产品名称的公司或其制造的

产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。

型号

E02S

2008

年

12

月

P/N DP855 Rev.A01

系统使用入门 15

安装和配置

警告：

执行下列步骤之前，请阅读系统随附的安全说明。

打开系统包装

打开系统包装并识别每件物品。

在机架中安装滑轨和系统

遵循系统随附的安全说明和机架安装说明组装滑轨并在机架中安装系统。

16 系统使用入门

可选

—

连接键盘、鼠标和显示器

连接键盘、鼠标和显示器（可选）。

系统背面的连接器附有图标，这些图标指示了要插入每个连接器的电缆。

确保拧紧显示器的电缆连接器上的螺钉（如果有）。

连接电源电缆

将系统电源电缆连接至系统，如果使用显示器，将显示器电源电缆连接至

显示器。

系统使用入门 17

固定电源线

如图所示，将系统电源电缆弯曲成一个环路，并使用所提供的腕带将其固

定到支架。

将电源线的另一端插入接地的电源插座或一个单独的电源，如不间断电源

设备

(UPS)

或配电装置

(PDU)

。

开启系统

按下系统和显示器的电源按钮。电源指示灯将会亮起。

18 系统使用入门

安装可选挡板

安装挡板（可选）。

完成操作系统安装

如果购买了预安装的操作系统，请参阅随系统提供的操作系统说明文件。

第一次安装操作系统时，请参阅操作系统的安装和配置说明文件。请确保

先安装操作系统，然后再安装未预装的硬件或软件。

•

Citrix

®

XenServe™ 5.0

，附带热修复程序

1

或更高版本

•

Microsoft

®

Windows Server

®

2008 Hyper-V™

•

Microsoft Windows Server 2008 Web

、

Standard

和

Enterprise

（

32

位

x86

）

Gold

版

•

Microsoft Windows Server 2008 Web

、

Standard

、

Enterprise

和

Datacenter (x64) Gold

版

•

Microsoft Windows Small Business Server 2008 Standard

和

Premium

(x64)

版

•

Microsoft Windows Server 2003 Web

、

Standard

和

Enterprise

（

32

位

x86

）版（含

SP2

）

•

Microsoft Windows Server 2003 Standard

和

Enterprise (x64)

版

（含

SP2

）

•

Microsoft Windows Server 2003 R2 Standard

和

Enterprise

（

32

位

x86

）

版（含

SP2

）

ページが読み込まれています...

Dell POWEREDGE R710 クイックスタートガイド

Dell POWEREDGE R710 クイックスタートガイド

他の言語で

関連論文