Philips HX9997/32 ユーザーマニュアル

9900 Prestige

1

4

5

6

7

9

10

2

3

13

14

8

1615

12

11

empty page before TOC

English 6

简体中文

24

繁體中文

46

English

6

English

Introduction

Congratulations on your new Philips Sonicare power

toothbrush! Superior plaque removal, whiter teeth,

and healthier gums are at your fingertips. Using

Sonicare’s combination of gentle sonic technology

and clinically developed and proven features, you can

be confident that you’re getting the very best clean,

every time.

Further support and product registration are available

to you at: www.philips.com/Prestige-Get-Started

Welcome to the Philips Sonicare family!

Important safety information

Only use the product for its intended purpose. Read

this important information carefully before you use

the product and its batteries and accessories, and

save it for future reference. Misuse can lead to

hazards or serious injuries.

Warnings

- Keep the charger away from water.

- After cleaning, make sure the charger is completely

dry before you connect it to the wall socket.

- This appliance can be used by children and

persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if

they have been given supervision or instruction

concerning use of the appliance in a safe way and

understand the hazards involved. Cleaning and

user maintenance shall not be made by children

without supervision.

- Children shall not play with the appliance.

- Only use original Philips accessories or

consumables. Only use the charger provided with

the product. If supplied, only use the original USB

cable and USB power supply unit.

7

English

- This appliance contains no user-serviceable parts.

If the appliance is damaged, stop using it and

contact the Consumer Care Center in your country

(see 'Warranty and support'). If the cord is

damaged, replace the charger with a new one.

- Do not use the charger outdoors or near heated

surfaces.

- Do not clean any part of the product in the

dishwasher.

- This appliance has only been designed for cleaning

teeth, gums and tongue.

- Stop using the appliance and consult your

dentist/doctor if excessive bleeding occurs after

use, if bleeding continues to occur after 1 week of

use or if you experience discomfort or pain.

- If you have had oral or gum surgery in the previous

2 months, consult your dentist before you use this

appliance.

- If you have a pacemaker or other implanted device,

contact your doctor or the manufacturer of the

implanted device prior to use.

- If you have medical concerns, consult your doctor

before you use this appliance.

- This appliance is a personal care device and is not

intended for use on multiple patients in a dental

practice or institution.

- Stop using a brush head with crushed or bent

bristles. Replace the brush head every 3 months or

sooner if signs of wear appear.

- If your toothpaste contains peroxide, baking soda

or bicarbonate (common in whitening

toothpastes), thoroughly clean the brush head with

soap and water after each use. This prevents

possible cracking of the plastic.

- Avoid direct contact with products that contain

essential oils or coconut oil. Contact may result in

bristles dislodging.

8

English

- To charge the battery, only use the USB wall

adapter, charging base and charging travel case

provided with the product: WAA1001, WAA2001,

HX9200 or HX9200/B, and TCC1001, TCC2001,

TCC3001, CBB1001 or CBB2001. Do not use an

extension cord.

- Charge, use and store the product at a

temperature between 0°C and 40°C.

- Keep product and batteries away from fire and do

not expose them to direct sunlight or high

temperatures.

- If the product becomes abnormally hot or smelly,

changes color or if charging takes longer than

usual, stop using and charging the product and

contact Philips.

- Do not place products and their batteries in

microwave ovens or on induction cookers.

- Do not open, modify, pierce, damage or dismantle

the product or battery to prevent batteries from

heating up or releasing toxic or hazardous

substances. Do not short-circuit, overcharge or

reverse charge batteries.

- If batteries are damaged or leaking, avoid contact

with the skin or eyes. If this occurs, immediately

rinse well with water and seek medical care.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic fields.

Radio Equipment Directive

Hereby, Philips declares that electric tootbrushes

equipped with a radio frequency interface (Bluetooth

or BrushSync) are in compliance with Directive

2014/53/EU.

- Bluetooth radio frequency: 2.4 GHz

- Maximum Bluetooth radio frequency power: 3 dBm

- NFC radio frequency: 13.56 MHz

- Maximum NFC radio frequency power: 30.16 dBm

9

English

The full text of the EU declaration of conformity is

available at the following internet address:

www.philips.com/support

Intended use

Sonicare Prestige power toothbrushes are intended to

remove adherent plaque and food debris from the

teeth to reduce tooth decay and improve and

maintain oral health. Prestige power toothbrushes are

intended for consumer home use. Use by children

should be supervised by an adult.

Your Philips Sonicare

1 Hygienic travel cap

2 Premium All-in-One brush head (A3)

3 BrushSync symbol

4 Handle

5 Power on/off button

6 Intensity indicator and hidden button

7 SenseIQ indicator

8 Brush head replacement reminder indicator

9 Battery indicator

10 Brushing feedback light

11 Charging base

12 Charging stand

13 USB-A wall adapter

14 USB-C cord

15 Charging travel case

16 USB-C socket

Note: The content of the box may vary based on the

model purchased.

The following symbols may appear on the product:

Read Operator’s Manual.

10

English

Detachable Power Supply Part:The "xxxxxx" indicates

the model number of the approved chargers to be

used.

Sonicare App - Getting Started

The Sonicare app pairs with your toothbrush to

provide you a connected experience. By connecting

your toothbrush to your Sonicare app account, you

will be able to:

- Customize your Sonicare toothbrush settings

according to your preferred modes, intensity and

toothbrush feedback.

- Track your brushing progress.

- Receive personalized tips and actionable

recommendations to improve your oral health.

- Access the full range of benefits and receive

ongoing upgrades to your Prestige experience.

The app is compatible with a wide range of iPhone

and Android™ smartphones. More information is

available at www.philips.com/Prestige-Get-Started

To start using the Sonicare app:

S7920

1

Download the Sonicare app to your phone.

2

Ensure your phone's Bluetooth is turned on.

3

Pick up your toothbrush to ensure it is active (lights

on).

4

Open the app and follow guided steps.

5

Pair your toothbrush with the app.

6

Create your account via the app. Complete

firmware update, if prompted, to access the latest

improvements and features.

7

Brush regularly. You are ready to start your

connected experience. When you regularly sync

the toothbrush with the app, you can receive

updates to help improve your oral healthcare.

11

English

8

Sync regularly.

- To sync manually: Pair/connect your toothbrush

with the app every couple of weeks to benefit from

the app features/capabilities.

- To sync automatically: Allow location permission

while setting up the app. By allowing location

permissions, your phone knows when it is in the

connection range of your toothbrush and can

refresh your brushing data to the app to provide

the latest insights and recommendations

Note: Make sure your phone's Bluetooth is turned on

when using the app so that your toothbrush can

transfer and update your brushing data to the app. If

you have questions about why your brushing data is

collected, be sure to review the Sonicare Privacy

Statement, available throughout the app setup

process.

App - Features

The Sonicare App provides customizable settings for

your toothbrush according to your preference,

including:

- Intensity Settings

- Mode Controls

- Enable and disable Adaptive Intensity

- Enable and disable Scrubbing feedback

Brush Head

Your Sonicare Prestige power toothbrush comes with

the new "Premium All-in-One brush head" (A3). This

brush head is specifically designed to provide

exceptional plaque removal, whitening (stain

removal), and gum health benefits.

Premium All-in-One brush heads come with

BrushSync Technology (see description below) as

indicated by the

symbol at the bottom of the brush

head.

To explore our full range of brush head options,

please visit our website for more information:

www.philips.com/toothbrush-heads

12

English

Using your Philips Sonicare

Brushing instructions

1

Push the brush head firmly onto the handle.

Note: It is normal to see a slight gap between the

brush head and the handle. This allows the brush

head to vibrate properly.

2

Wet the bristles and apply a small amount of

toothpaste.

45°

3

Place the toothbrush bristles against the teeth at a

slight angle (45 degrees). Apply light pressure to

make the bristles reach the gumline or slightly

beneath the gumline.

Note: Keep the center of the brush head in contact

with the teeth at all times.

4

Press the power on/off button to turn on the

Philips Sonicare.

5

Apply light pressure to maximize Philips Sonicare’s

effectiveness and let the Philips Sonicare

toothbrush do the brushing for you.

13

English

Note: The bristles should slightly flare. Do not

scrub. A change in vibration from the handle and

the brushing feedback light flashes purple to alert

you when you apply too much pressure.

Gently move the brush head slowly across the

teeth in a small back and forth motion so the

longer bristles reach between your teeth. Continue

this motion throughout the brushing cycle.

6

To clean the inside surfaces of the front teeth, tilt

the brush handle semi-upright and make several

vertical overlapping brushing strokes on each

tooth.

1

2

3

4

5

6

7

The BrushPacer divides the brushing time into six

equal segments and indicates when you should

move to the next area. Segments are indicated

with a brief pause in vibration. The toothbrush

automatically stops at the end of the brushing

session.

Note: Your Philips Sonicare toothbrush is safe to use

on braces, dental modifications and dental

restorations (fillings, crowns, veneers)

Brushing modes

Your power toothbrush comes pre-set to the all-in-

one clean mode that provides the dentist

recommended 2 minute brushing routine, with a six

segment brush pacer.

To personalize your brushing mode you can

customize your power toothbrush settings from the

Sonicare app (see 'Sonicare App - Getting Started').

Note: Although a mode is not displayed on the

toothbrush handle, you can update the mode any

time from the Sonicare App and your selection will be

stored.

14

English

Intensity settings

Your power toothbrush comes with 3 different

intensity settings:

- High intensity (three lights)

- Medium intensity (two lights)

- Low intensity (one light)

×3

×1

×2

To manually select your desired intensity, press the

intensity indicator lights on the handle, to cycle

through the options. The intensity setting can be

changed before, during, or after brushing.

Note: The intensity setting can also be customized

from the Sonicare app.

BrushSync technology

BrushSync technology enables your brush head to

communicate with your handle using a microchip. The

symbol at the bottom of the brush head indicates

that the brush head is equipped with this technology.

BrushSync technology enables:

- Brush head replacement reminder

- BrushSync mode paring (for Tongue Care brush

heads)

Features

- SenseIQ

- Pressure Sensor Feedback

- Adaptive Intensity

- Scrubbing Feedback

- BrushPacer

- Brush head replacement reminder

SenseIQ

Your Sonicare is equipped with SenseIQ technology

that is a combination of smart features that observe

your brushing behaviors (e.g. motions, habits, brush

head choice) and provide personalized feedback and

recommendations.

The SenseIQ features include:

- Adaptive Intensity

15

English

- Real time feedback:

- Scrubbing Feedback

- Pressure Sensor Feedback

- Personalized recommendations in the app

- Brushing behavior feedback in the app

The SenseIQ icon on the handle will illuminate when

the smart features are active:

- while brushing

- to confirm enabling and disabling of settings

Pressure Sensor Feedback

Your Sonicare toothbrush measures the pressure you

apply while brushing to protect your gums and teeth

from damage.

If you apply excess pressure, the handle will change

its vibration and the brushing feedback light will flash

(purple) at the bottom of the handle until you reduce

the pressure.

Note: The Pressure Sensor comes activated with your

product. To deactivate this feature, see 'Activating or

deactivating features'.

Adaptive intensity

Your Sonicare toothbrush is designed with Adaptive

Intensity to protect your gums. If you apply excess

pressure for an extended period of time, your

toothbrush will automatically lower the intensity

setting 1 level. You will experience a brief pause in the

pressure feedback and feel the intensity adjust to the

next lower level.

Note: Adaptive Intensity comes activated with your

product. To deactivate this feature, see 'Activating or

deactivating features'.

Note: Every new brushing cycle the intensity will go

back to your pre-selected setting.

Scrubbing Feedback

Your Sonicare toothbrush measures the motions while

brushing to detect scrubbing behavior (see brushing

instructions for optimal technique). If you regularly

16

English

scrub while brushing, the app will recommend that

you enable Scrubbing Feedback.

When Scrubbing Feedback is activated the brushing

feedback light at the bottom of the handle will

illuminate amber and the handle will change its

vibration as a reminder to stop scrubbing. The

brushing feedback light will turn off when you stop

scrubbing.

Note: Scrubbing Feedback comes deactivated. To

activate this feature, see 'Activating or deactivating

features'.

BrushPacer

1

2

3

4

5

6

The BrushPacer divides the brushing time into six

equal segments and indicates when you should move

to the next area. Segments are indicated with a brief

pause in vibration. The toothbrush automatically

stops at the end of the brushing session.

Note: Additional segments may be added when you

use White+ or Gum Health Modes. See Sonicare app

for mode descriptions.

Brush head replacement reminder

Your Sonicare toothbrush will track the wear of your

smart brush head, using the BrushSync technology to

measure:

- The overall pressure you apply while brushing

- The total time you have brushed with your brush

head

Once your brush head is no longer effective, the brush

head replacement reminder indicator light will blink

amber and the handle will make a series of beeps and

tones to indicate it is time to replace your brush head.

Note: The brush head replacement reminder comes

activated with your product. To deactivate this

feature, see 'Activating or deactivating features'.

Activating or deactivating features

You can activate or deactivate the following features

of your toothbrush:

17

English

- Adaptive Intensity

- Pressure Sensor Feedback

- Scrubbing Feedback

- Brush head replacement reminder

Note: Adaptive Intensity will be deactivated when

pressure sensor is deactivated.

From app

The following features can be activated or deactivated

from the Sonicare app.

- Adaptive Intensity

- Scrubbing Feedback

For instruction for how to connect to the app (see

'Sonicare App - Getting Started').

From handle

Step 1: Place the handle on the charging stand.

Step 2: Press and hold power button for:

Adaptive

intensity

Brush head

replacement

reminder

Pressure Sensor

Feedback

up to 3 seconds Up to 5 seconds Up to 7 seconds

¯ ¯ ¯

Step 3: Let go power button when you hear

1 beep 1 beep and then

2 beeps

1 beep, 2 beeps and

then 3 beeps

¯ ¯ ¯

18

English

SenseIQ

indicator lights

up for 3

seconds

Brush head

replacement

reminder

indicator lights

up for 3

seconds

SenseIQ indicator and

light ring lights up

purple for 3 seconds

Together with:

If you see the battery indication blink white 3 times and

hear 3 tones from low to high, then the feature has been

activated.

OR

If you see battery indication blink amber 3 times and hear 3

tones high to low, then the feature has been deactivated.

Charging and battery status

Charging on charger base

1

2

1

Plug the USB cord of the charging base into the

USB wall adapter and plug the wall adapter into an

electrical outlet.

2

Place the charging stand (clear cover) on the

charging base.

19

English

3

Place the toothbrush handle on the charger.

a To indicate charging has started successfully,

the toothbrush will beep twice and the lights

will illuminate in an upward motion.

b While charging the battery indicator blinks in

white.

4

Leave the toothbrush on the charger until it is fully

charged. The battery light will turn off (stop

blinking) when the handle has finished charging.

Note: It may take 12-14 hours to fully charge your

Sonicare toothbrush.

Charging with the travel case

1

Plug the USB cord into the travel case and into the

USB wall adapter.

2

Plug the wall adapter into an electrical outlet.

1

2

3

Place toothbrush into travel case.

a To indicate charging has started successfully,

the toothbrush will beep twice and the lights

will illuminate in an upward motion.

b While charging the battery indicator blinks in

white.

4

Leave travel case plugged in until toothbrush is

fully charged. The battery light will turn off (stop

blinking) when the handle has finished charging.

20

English

Note: Make sure the travel case is placed on its side

for better stability.

Battery Status (when handle is on a working charger or travel

case)

When the handle is placed on the charger or in the

travel case, the battery indication will communicate

the battery level.

Battery status

Battery indication

Charging Blinks in white

Full Illuminates white for 30 seconds

and then turns off.

Battery Status (when handle is not placed on Charger)

When the toothbrush is awake, the battery light at the

bottom of the handle will indicate the status of the

battery.

Battery status Battery indication Sound

Full Illuminated in white -

Partially full Blinks white -

Low Blinks amber The handle emits 3

beeps after brushing

Empty Blinks amber The handle emits 2

sets of beeps after

brushing

Cleaning

Brush head and handle

The brush heads and handle can be cleaned by

rinsing it with warm water.

ページが読み込まれています...

Philips HX9997/32 ユーザーマニュアル

このマニュアルも適しています

Philips HX9997/32 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント