Philips 11342ULX2 ユーザーマニュアル

タイプ
ユーザーマニュアル
Dimensions: 100mm x 65mm Material: Paper 80g/m2
LED-HEADLIGHT
LAMP [≈H4]
EN LED-HL [≈H4] upgrade lamp 3
12
21
30
39
简体中文 LED-HL [≈H4] 升级灯
繁體中文 LED-HL [≈H4] 升級燈泡
日本語
LED-HL [≈H4]
ップグレードランプ
한국어
LED-HL [≈H4]
업그레이드 램프
LED-HL [H4]
Ultinon
EN Please read through the instructions carefully before use
and keep them in a safe place for ease of reference in
the future.
简体中文 使用前请仔细阅读使用说明,并将说明书存放于安
全处以便今后参考。
繁體中文 使用前請詳閱指示說明,然後妥善保存,以利日後
參閱。
日本語 ご使用にな前に説明書を良お読みにな
今後必要時に手軽に参照できる安全な
場所に説明書を保管い。
한국어 사용하기 전에 이 사용 설명서를 주의 깊게 읽고
향후 참조를 위해 안전한 곳에 보관하십시오.
3
Packing list
Product features
LED-HEADLIGHT
/$03>§+@
(1/('+/>§+@XSJUDGHODPS 3
12
21
30
39
ࣇບሱ༵ /('+/>§+@඘ࢋ؉
ᐥ᛽ɻʼ/('+/>§+@ʠज़዗؞
日本語
/('+/>§+@
アップグレードランプ
㨚ഷ⢃#####
/('+/>§+@#
⢕ීᤢ⩺ᖒ#ᢵ㦸
LED-HL [H4]
Ultinon
LED Lamp H4 ×2
Plastic tie ×4 User Manual x1
Before you install the LED-HL [≈H4] lamp, please read
through the following information carefully.
Operating voltage: 13.2V
Power: 15.5W ±15%
Light ux: Low Beam:900lm ±20%
High Beam:1200lm±20%
Colour temperature: 5700K ±500K
Important
This product can only be used with a car power input of 12V.
This product can only be used in headlights with H4
halogen lamps.
m Precautions
1
2
3
4
• Prior to installation, please make sure that the LED-HL
[≈H4] Ultinon lamp does not have defects such as
damage or rupture.
m Warnings
When working, the LED-HL [≈H4] lamp and body will
be at a very high with temperature. Do not touch them
directly ngers or skin, to avoid scalding.
Usable with: Reector headlights
5
The LED illumination of the LED-HL [≈H4] lamp is of
high intensity; do not look directly at the LED-HL [≈H4]
lamp, to avoid eye damage.
• Before you remove the halogen H4 lamp, make sure
that the lamp’s temperature has dropped to room
temperature, to avoid burning ngers or skin.
• Do not let the LED-HL [≈H4] lamp become exposed
to dust, grease or stains, or scratch the surface of the
LED; this will dam- age the LED-HL [≈H4] lamp.
• Do not let children touch the LED-HL [≈H4] product.
• Please make sure that you purchase the Philips LED-HL
[≈H4] lamp through the correct channels.
After the lamp is installed, please check if the light
pattern is okay, and make sure that the indicators on
the dash board are working normally and that nothing
is abnormal.
After the lamp is installed, please check whether the
air-tight cover is properly sealed to avoid undesirable
sealing; and whether the control box and the wiring har-
ness are rmly in place, and not interfering with other
parts inside the lamp or the fan above the lamp.
m Other Information
6
• Ensure that there is at least 70mm of space behind the
headlight xture and that the xture has a diameter of
60mm as shown in Figure 1.
Pre-installation Information
The LED-HL [≈H4] lamp is not for use with all types of
cars. Please consult a professional sales representative.
• Please have a technician at a professional service
location install the LED-HL [≈H4] lamp.
• If it is found, after the LED-HL [≈H4] lamp is installed,
that there is no cut-off line for the low-beam light
pattern, please switch back to your previous halogen
H4 lamp.
Applicable car types: Please refer to the overview of
applicable cars.
4
Figure-1
7
• 5.1 Ensure that the light xture has a gasket seal and a
metal spring or similar attachment mechanism. Use the
metal spring to attach the bulb as shown in Figure 2.
Installation steps for lamps
5
• 5.2 Take the original bulb and gasket out of the light xture.
• 5.3 Unscrew the heat sink from the LED4 headlight,and
take out the heatsink from the burner and connector as
shown in Figure 3.
Figure-3
Figure-2
8
• 5.4 Attach the LED4 burner into the bayonet of the light
xture as shown in Figure 4.
• 5.5 Attach the metal spring.
• 5.6 Assemble the gasket on the LED4 burner and
ensure it is in the correct position as shown in Figure 5.
• 5.7 Adjust the heat sink into the correct position until it
cannot rotate further as shown in Figure 6. Ensure that
the air inlet channel for the heat sink is not blocked.
Figure-4
Figure-5
9
• 5.8 Connect the power connector as shown in Figure 7.
• 5.9 Fixing the wire harness with plastic cable tie.
• 5.10 Check that the high and low beams of the LED4
headlight bulb both function correctly.
• 5.11 If the beams are positioned too high or too low,
adjust the light axis to an appropriate position as needed.
• 5.12 Store the o iginal H4 bulb and the LED4 headlight
instruction manual in a safe place.
• 5.13 The low beam should nally be equipped with the
clear bright-dark cut-off line shown in the lower left
gure; left gure for left drive vehicle, right gure for
right drive vehicle.
Figure-7
Figure-6
10
Left hand drive Right hand drive
This product is designed in compliance with the
applicable requirements of European Directive
2002/96/EC. Its parts and elements may be
recycled for reuse.
Do not discard this product carelessly. Certain
substances in the electronic elements can be
harmful for the environ-ment and humans.
Recycling
7
If the LED-HL [≈H4] lamp does not turn on, please check
if any of the following conditions exists:
1. Are the positive and negative power connectors
properly connected?
2. Check if the power switch for the lamp is turned on.
3. Make sure that there is sufcient power in the battery.
Troubleshooting
6
11
Warranty clauses
8
Warranty is only valid under normal use. All man-made
damage, such as connecting to inadequate power, failure
to follow the instructions for use, damage caused by
maintenance or modication not approved of by this
company, wrongful use or negligence, or damage caused
by disasters, invalidate warranty services immediately.
• If the Warranty Card or purchase receipt have been al-
tered, you will no longer be entitled to warranty services.
• Please contact the distributor from which you purchased
the product; the distributor will help you with the
warranty repair service associated with this product.
In the event of a warranty claim, please provide the
following information together with proof of purchase:
Name______________ Address___________________
Phone______________ Postal code________________
Purchased from:
(Please provide the name and location of the retail outlet)
_____________________________________________
12
包装清单
产品特性
LED-HEADLIGHT
/$03>§+@
(1/('+/>§+@XSJUDGHODPS 3
12
21
30
39
ࣇບሱ༵ /('+/>§+@඘ࢋ؉
ᐥ᛽ɻʼ/('+/>§+@ʠज़዗؞
日本語
/('+/>§+@
アップグレードランプ
㨚ഷ⢃#####
/('+/>§+@#
⢕ීᤢ⩺ᖒ#ᢵ㦸
LED-HL [H4]
Ultinon
重点提示
1
2
3
LEDH4 ×2 塑料扎带 ×4 用户手册 ×1
工作电压: 13.2V
功率: 15.5W ±15%
光通量: 低光束: 900lm ±20%
高光束: 1200lm±20%
色温: 5700K ±500K
安装 LED-HL [≈H4] 灯之前,请仔细阅读以下信息。
本产品只适用于 12V 汽车电源输入。
本产品只适用于使用 H4 卤素灯的前灯。
m 注意
13
安装之前,请确保 LED-HL [≈H4] Ultinon 灯没有损
坏或破裂等缺陷。
m 警告
LED-HL [≈H4]灯工作时,灯体温度极高。请勿使其
直接接触手指或皮肤以免烫伤。
可用于:反光碗前灯
14
m 其他信息
LED-HL [≈H4] 灯的 LED 照明强度很高;请勿直视
LED-HL [≈H4] 灯以免眼睛受到伤害。
拆除 H4 卤素灯之前,请确保灯的温度已降至室温
以免烫伤手指或皮肤。
请勿使 LED-HL [≈H4] 灯沾染灰尘、油脂或污渍,或
者划伤 LED 表面,否则会损坏 LED-HL [≈H4] 灯。
请勿让儿童触碰 LED-HL [≈H4] 产品。
请确保通过正确渠道购买飞利浦 LED-HL [≈H4] 灯。
灯安装完毕后,请检查灯光模式是否合适,并确
保仪表盘上的指示灯处于正常工作状态,没有异
常现象。
灯安装完毕后,请检查密封盖是否正确密封,以免
密封不良,并检查控制盒和电线束是否固定到位,
不干扰灯内的其他零件或灯具上方的风扇。
15
请确保前灯灯具后方至少具有 70mm 的空间,且灯
具直径为 60mm,如图 1 所示。
LED-HL [≈H4] 灯并非适用于所有类型的汽车。请咨
询专业销售代表。
请让专业服务点的技术人员安装 LED-HL [≈H4] 灯。
如果 LED-HL [≈H4] 灯安装完毕后发现低光束灯光模
式没有明暗截止线,请恢复为之前的 H4 卤素灯。
适用的汽车类型:请参考适用车型概述。
预安装信息
4
图-1
16
• 5.1
请确保灯具装有垫圈密封件和金属弹簧或类似
的连接结构。用金属弹簧连接灯泡,如图 2 所示。
灯的安装步骤
5
5.2
从灯具中取出原厂灯泡和垫圈。
5.3
LED4 前灯上拆下散热器,并从燃烧器和连接
器上取出散热器,如图 3 所示。
-3
-2
17
5.4 LED4 燃烧器装在灯具卡口上,如图 4 所示。
5.5 装上金属弹簧。
5.6 将垫圈组装在 LED4 燃烧器上,确保其处于适
当位置,如图 5 所示。
5.7 调整散热器至适当位置直至其无法转动为止,
如图 6 所示。确保散热器进气通道畅通。
-4
-5
18
5.8 连接电源连接器,如图 7 所示。
-7
-6
5.9 用塑料电缆扎带固定电线束。
5.10 检查 LED4 前灯灯泡的高低光束是否正常工作。
5.11 如光束位置太高或太低,调整光轴至所需的
适当位置。
5.12 将原厂 H4 灯泡和 LED4 前灯使用说明书存放
于安全处。
5.13 低光束最终应具备左下图中所示的清晰明暗
截止线;左图为靠左行驶车辆,右图为靠右行驶
车辆。
19
左舵驾驶 右舵驾驶
本产品的设计符合欧洲指令 2002/96/EC 的适
用要求。其零件和元件可回收利用。
请勿随意丢弃本产品。电子元件中的某些物
质可能对环境和人类有害。
回收
7
如果 LED-HL [≈H4] 灯打不开,请检查是否存在以下
任意一种情况:
1. 电源连接器正负极是否连接正确?
2. 检查灯的电源开关是否打开。
3. 确保电池中电量充足。
疑难解答
6
20
保用条例
8
保修仅在正常使用情况下有效。所有人为损坏,例
如连接的电源电压不足、未按照说明书使用、因未
经本公司批准的维护或改动、使用错误或疏忽导致
的损坏,或因灾害导致的损坏,均会直接导致保
修服务失效。
如果更改了保修卡或购买发票,将不再享受保修
服务。
请与出售产品的分销商联系;分销商将为您提供本
产品相关保修服务方面的帮助。
如出现保修索赔,请提供以下信息及购买证明:
姓名______________ 地址_______________________
电话号码_____________ 邮政编码________________
购买商家:
(请提供零售店的名称和位置)
_____________________________________________
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Philips 11342ULX2 ユーザーマニュアル

タイプ
ユーザーマニュアル