HP f520 Car Camcorder クイックスタートガイド

f520

完整版產品使用者手冊請至

f520

完整版產品用戶手冊請至

1

FCC Statement

This equipment has been tested and found to comply with the limits for a

Class B digital camcorder, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This camcorder complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This camcorder may not cause harmful

interference, and (2) this camcorder must accept any interference received,

including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate

this equipment.

CE Regulatory Notice

The product herewith complies with the requirements of the Low Voltage

Directive 2006/95/EC, the EMC Directive 2004/108/EC and the RoHS

Directive 2011/65/EC.

2

Battery warning



The battery for this car camcorder is sealed internally. DO NOT

attempt to disassemble the camcorder and remove the battery.



Always charge using the provided system. Improper charging of the

battery may result in explosion.



The battery is designed for this camcorder and is not customer

replaceable.



Batteries may explode if exposed to open fire. Never place the car

camcorder in a fire.



Recycle the camcorder observing local regulations.

Notes on Installation

1. Install the camcorder near the rear-view mirror to obtain the best

open-field view. Do NOT install the camcorder in a location that will

obstruct your required driving view.

2. Make sure that the lens is within the wiping range of the windscreen

wiper to ensure a clear view even when it rains.

3. Do not touch the lens with your fingers. Finger grease may be left on

the lens and will result in unclear videos or snapshots. Clean the

lens on a regular basis.

4.

Do not install the camcorder on a tinted window. Doing so may

damage the tint film.

5. Make sure that the installation position is not hindered by the tinted

window.

3

1 Introduction

1.1 Package Contents

The package contains the following items. In case there is any missing

or damaged item, contact your dealer immediately.

Camcorder Bracket CD-ROM

Quick start guide Car adapter

4

Top and Bottom Views

Side (Left and Right) Views

Front View

Rear View

1

2

3

8

6

11

4

5

9

10

12

13

1.2 Product Overview

No.

Item

No.

Item

1

Bracket Socket

8

Up Button (

)

2 Power Button

9 Down Button ( )

3

Memory Card Slot

10

Enter Button (

)

4

USB Connector

11

Speaker

5

Back Button (

)

12

Wide Angle Lens

6

LED

Indicator

13

Microphone

7

LCD Panel

5

2 Getting Started

2.1 Inserting the Memory Card

Insert the memory card with the gold contacts facing the back of the

camcorder. Push the memory card until it clicks into place.

To remove the memory card

Push to eject the memory card out of the slot.

Note:

1. Do not remove or insert the memory card when the camcorder is turned on. This

may damage the memory card.

2. Please use a 32GB, Class 10 or above Micro SD card.

3. Please format the micro SD cards before the initial use.

4. If the screen shows “Low Speed Card” while recording, it means the writing speed of

the memory card is too slow. Please replace it with a higher-speed memory card.

5. If “Card is too fragmented” is displayed while recording, it means the card is unable

to save the recording. Please make a copy of existing files in the card and then

reformat it with this camcorder.

6

2.2 Installing in Vehicles

2.2.1 Mount to Windshield

1. Attach the bracket to the camcorder.

Slide it into the bracket holder until

you hear a click.

2. Before installing the bracket, please

use alcohol to clean the windshield

and suction cup of the bracket. Wait

for dry and press suction-cup on the

windshield.

3. Hold the base firmly on the

windshield and press down the clamp

to mount the car holder to the

windshield. Make sure the base is

securely locked in place.

7

2.2.2 Adjust the camcorder position

1. Loose the knob to swivel the device vertically or horizontally.

2. Then tighten the knob to make sure the camcorder is securely

locked in place.

Knob

8

2.3 Connecting to Power

Use only the supplied car adapter to power up the camcorder and

charge the built-in battery.

1.

Connect one end of the car adapter to the USB connector of the

camcorder.

2.

Plug the other end of the car charger to the cigarette lighter

socket of your vehicle. Once the vehicle engine is started, the

camcorder automatically turns on.

Note:

1. To use the products of the attached power charger only, please do not use other

brand power charger, in order to avoid equipment burn or cause the battery

explosion.

2. When first use this camcorder, please charging to battery full.

3. Please take note if the environment temperature reaches 45°C or above, the car

adapter still can supply power to camcorder, but it will not charge the Lithium-ion

battery. This is the characteristic of Lithium-ion and is not a malfunction.

9

2.4 Powering the Camcorder On / Off

2.4.1 Auto Power On/Off

Once the vehicle engine is started, the camcorder automatically turns

on. If the Automatic Record function is enabled, the recording will

automatically start right after the camcorder turns on.

2.5 Initial Settings

Before using the camcorder, we recommend you to enable the

Automatic Record function and set up the correct date and time.

10

3 Using the Camcorder

3.1 Recording Videos

3.1.1 Motion Detection

If Motion Detection is activated, when power off the camcorder, the

system alert message, “Press OK Key to Power off, or enter motion

detection after 10sec.”, will pop on the screen. This means the

system will enter Motion Detection automatically in 10 seconds; when

the camcorder detects any motion in front of lens, Video Record will

be activated for a duration the same as the length setting.

To set the motion detection, do the following:

1. Press the button to enter the OSD menu.

2. Press the / button to select Motion Detection and press

the button.

3. Press the / button to select On and press the

button.

4. Press the button to exit the menu.

Note:

1. When the battery is fully charged and is in good condition, Motion Detection can

record continuously for about 30 minutes.

2. As the camcorder is used, the battery storage capacity will decrease gradually. This

is a normal phenomenon for the battery

3. The LCD will be off in 30 seconds after the Motion Detection function is enabled.

11

3.1.2 Emergency Recording

During Video Recording, press the

button to enter emergency

recording mode, the “Emergency”

message will be shown immediately

on the upper left corner of the screen,

and the recorded file will be protected.

To stop the recording, press the

button.

Note:

1. If the Collision Detection function is enabled and a collision is detected, the

camcorder will automatically trigger the emergency recording.

2. The emergency recording file is created as a new file, which will be protected to

avoid being overwritten by normal cycling recording. 4G memory card can save up

to 5 emergency video files, and 8G (or above) memory card can save up to 10

emergency video files. The alert message of “Emergency files are full” will pop up

on the screen when the emergency recording files are full, and the oldest

emergency file will be automatically deleted when a new emergency recording file

is created.

12

3.2 Playback Videos and Photos

To playback videos and photos, do the following:

1. During recording, press the

button to browse for the

desired video and photo file.

2. Press the / button to select the file category that you

want to browse and press the button.

3. Press the / button to view the next or the previous file

and press the button to view the file in full screen.

3.2.1

Deleting Files

To delete file(s), do the following:

1. If recording is in progress, Press the button to enter the

OSD menu.

2. Press the / button to select File Deletion and press the

button.

3. Press the / button to select the file category and press

the button.

4. Press the / button to select the file that you want to

delete and press the

button to enter the Delete menu.

5. Press the

/ button to select an option.

Item Description

Delete One Delete the current file.

Delete All Delete all files.

6. Press the button to confirm delete.

Note:

Deleted files cannot be recovered. Ensure the files have backup before deletion.