Tannoy PCI SUB IW WITH BACK CAN クイックスタートガイド

PCI SUB IW WITH BACK CAN
Tannoy
ブランド
Tannoy
モデル
PCI SUB IW WITH BACK CAN
カテゴリー
スピーカー
タイプ
クイックスタートガイド
Quick Start Guide
PCI In-Wall Subwoofer
PCI SUB IW
Premium Dual 8" In-Wall Subwoofer for Installation Applications
BACK CAN PCI SUB IW
Back Can Kit for PCI SUB IW In-Wall Speakers
2 PCI SUB IW Quick Start Guide 3
Instrucciones de
seguridad
NEGACIÓN LEGAL
GARANTÍA LIMITADA
Las terminales marcadas con este símbolo
transportan corriente eléctrica de
magnitud suciente como para constituir
un riesgo de descarga eléctrica. Utilice solo cables de
altavoz profesionales y de alta calidad con conectores
TS de 6,3 mm o de bayoneta prejados. Cualquier otra
instalación o modicación debe ser realizada únicamente
por un técnico cualicado.
Este símbolo, siempre que aparece,
leadvierte de la presencia de voltaje
peligroso sin aislar dentro de la caja;
estevoltaje puede ser suciente para constituir un riesgo
dedescarga.
Este símbolo, siempre que aparece,
leadvierte sobre instrucciones operativas
y de mantenimiento que aparecen en la
documentación adjunta. Por favor, lea el manual.
Atención
Para reducir el riesgo de descarga
eléctrica, no quite la tapa (o la parte
posterior). No hay piezas en el interior del equipo que
puedan ser reparadas por el usuario. Si es necesario,
póngase en contacto con personal cualicado.
Atención
Para reducir el riesgo de incendio o
descarga eléctrica, no exponga este
aparato a la lluvia, humedad o alguna otra fuente que
pueda salpicar o derramar algún líquido sobre el aparato.
Nocoloque ningún tipo de recipiente para líquidos sobre
el aparato.
Atención
Las instrucciones de servicio deben
llevarlas a cabo exclusivamente personal
cualicado. Para evitar el riesgo de una descarga eléctrica,
no realice reparaciones que no se encuentren descritas
en el manual de operaciones. Lasreparaciones deben ser
realizadas exclusivamente por personalcualicado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas las advertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie este aparato con un paño seco.
7. No bloquee las aberturas de ventilación. Instale el
equipo de acuerdo con las instrucciones del fabricante.
8. No instale este equipo cerca de fuentes de calor
tales como radiadores, acumuladores de calor, estufas u
otros aparatos (incluyendo amplicadores) que puedan
producir calor.
9. No elimine o deshabilite nunca la conexión a tierra
del aparato o del cable de alimentación de corriente.
Unenchufe polarizado tiene dos polos, uno de los cuales
tiene un contacto más ancho que el otro. Una clavija con
puesta a tierra dispone de tres contactos: dos polos y la
puesta a tierra. El contacto ancho y el tercer contacto,
respectivamente, son los que garantizan una mayor
seguridad. Si el enchufe suministrado con el equipo no
concuerda con la toma de corriente, consulte con un
electricista para cambiar la toma de corriente obsoleta.
10. Coloque el cable de suministro de energía de manera
que no pueda ser pisado y que esté protegido de objetos
alados. Asegúrese de que el cable de suministro de
energía esté protegido, especialmente en la zona de la
clavija y en el punto donde sale del aparato.
11. Use únicamente los dispositivos o accesorios
especicados por el fabricante.
12. Use únicamente la
carretilla, plataforma,
trípode, soporte o mesa
especicados por el
fabricante o suministrados
junto con el equipo.
Altransportar el equipo,
tenga cuidado para evitar
daños y caídas al tropezar con algún obstáculo.
13. Desenchufe el equipo durante tormentas o si no va a
utilizarlo durante un periodo largo.
14. Confíe las reparaciones únicamente a servicios
técnicos cualicados. La unidad requiere mantenimiento
siempre que haya sufrido algún daño, si el cable de
suministro de energía o el enchufe presentaran daños,
sehubiera derramado un líquido o hubieran caído objetos
dentro del equipo, si el aparato hubiera estado expuesto
a la humedad o la lluvia, si ha dejado de funcionar de
manera normal o si ha sufrido algún golpe o caída.
15. Al conectar la unidad a la toma de corriente eléctrica
asegúrese de que la conexión disponga de una unión
atierra.
16. Si el enchufe o conector de red sirve como único
medio de desconexión, éste debe ser accesiblefácilmente.
17. Cómo debe deshacerse de
este aparato: Este símbolo indica
que este aparato no debe ser
tratado como basura orgánica,
según lo indicado en la Directiva
WEEE (2012/19/EU) y a las
normativas aplicables en su país.
En lugar de ello deberá llevarlo al punto limpio más
cercano para el reciclaje de sus elementos eléctricos/
electrónicos (EEE). Al hacer esto estará ayudando a
prevenir las posibles consecuencias negativas para el
medio ambiente y la salud que podrían ser provocadas por
una gestión inadecuada de este tipo de aparatos. Además,
el reciclaje de materiales ayudará a conservar los recursos
naturales. Para más información acerca del reciclaje de
este aparato, póngase en contacto con el Ayuntamiento
de su ciudad o con el punto limpio local.
18. No instale esta unidad en un espacio muy reducido,
tal como encastrada en una librería o similar.
19. No coloque objetos con llama, como una vela
encendida, sobre este aparato.
20. Tenga presentes todas las advertencias relativas
al reciclaje y correcta eliminación de las pilas. Las pilas
deben ser siempre eliminadas en un punto limpio y nunca
con el resto de la basura orgánica.
21. Use este aparato en rangos de temperatura
moderados y/o tropicales.
Music Tribe no admite ningún tipo de responsabilidad
por cualquier daño o pérdida que pudiera sufrir
cualquier persona por conar total o parcialmente en
la descripciones, fotografías o armaciones contenidas
en este documento. Las especicaciones técnicas,
imágenes y otras informaciones contenidas en este
documento están sujetas a modicaciones sin previo
aviso. Todas las marcas comerciales que aparecen
aquí son propiedad de sus respectivos dueños. Midas,
Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound,
TC Electronic, TC Helicon, Behringer, Bugera y Coolaudio
son marcas comerciales o marcas registradas de
Music Tribe Global Brands Ltd. © Music Tribe Global
Brands Ltd. 2019 Reservados todos los derechos.
Si quiere conocer los detalles y condiciones aplicables
de la garantía así como información adicional sobre la
Garantía limitada de Music Tribe, consulte online toda la
información en la web musictribe.com/warranty.
Terminals marked with this symbol carry
electrical current of sucient magnitude
to constitute risk of electric shock.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. Allother
installation or modication should be performed only
by qualiedpersonnel.
This symbol, wherever it appears,
alertsyou to the presence of uninsulated
dangerous voltage inside the
enclosure-voltage that may be sucient to constitute a
risk ofshock.
This symbol, wherever it appears,
alertsyou to important operating and
maintenance instructions in the
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, donot
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualied personnel.
Caution
To reduce the risk of re or electric shock,
do not expose this appliance to rain and
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects lled with liquids,
suchas vases, shall be placed on the apparatus.
Caution
These service instructions are for use
by qualied service personnel only.
Toreduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualied
servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. Ifthe
provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Use only attachments/accessories specied by
themanufacturer.
12. Use only with the
cart, stand, tripod, bracket,
or table specied by the
manufacturer, orsold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
beendropped.
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
17. Correct disposal of this
product: This symbol indicates that
this product must not be disposed
of with household waste,
according to the WEEE Directive
(2012/19/EU) and your national
law. This product should be taken
to a collection center licensed for the recycling of waste
electrical and electronic equipment (EEE). The
mishandling of this type of waste could have a possible
negative impact on the environment and human health
due to potentially hazardous substances that are generally
associated with EEE. At the same time, your cooperation
in the correct disposal of this product will contribute to
the ecient use of natural resources. For more
information about where you can take your waste
equipment for recycling, please contact your local city
oce, or your household waste collection service.
18. Do not install in a conned space, such as a book
case or similar unit.
19. Do not place naked ame sources, such as lighted
candles, on the apparatus.
20. Please keep the environmental aspects of battery
disposal in mind. Batteries must be disposed-of at a
battery collection point.
21. Use this apparatus in tropical and/or
moderate climates.
Music Tribe accepts no liability for any loss which
may be suered by any person who relies either
wholly or in part upon any description, photograph,
or statement contained herein. Technical specications,
appearances and other information are subject to
change without notice. All trademarks are the property
of their respective owners. Midas, Klark Teknik,
Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic,
TC Helicon, Behringer, Bugera and Coolaudio are
trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd.
2019 All rights reserved.
For the applicable warranty terms and conditions
and additional information regarding Music Tribe’s
Limited Warranty, please see complete details online at
musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10 Wanmei Road, South China Modern Chinese
Medicine Park, Nanlang Town, 528451, Zhongshan City,
Guangdong Province, China
Important Safety
Instructions
LEGAL DISCLAIMER
LIMITED WARRANTY
4 PCI SUB IW Quick Start Guide 5
Consignes de sécurité
DÉNI LÉGAL
GARANTIE LIMITÉE
Wichtige
Sicherheitshinweise
HAFTUNGSAUSSCHLUSS
BESCHRÄNKTE GARANTIE
Les points repérés par ce symbole portent
une tension électrique susante pour
constituer un risque d’électrocution.
Utilisez uniquement des câbles d’enceintes professionnels
de haute qualité avec ches Jack mono 6,35 mm ou ches
à verrouillages déjà installées. Touteautre installation ou
modication doit être eectuée uniquement par un
personnel qualié.
Ce symbole avertit de la présence d’une
tension dangereuse et non isolée à
l’intérieur de l’appareil - elle peut
provoquer des chocs électriques.
Attention
Ce symbol signale les consignes
d’utilisation et d’entre ! Tien importantes
dans la documentation fournie. Lisez les consignes de
sécurité du manuel d’utilisation de l’appareil.
Attention
Pour éviter tout risque de choc électrique,
ne pas ouvrir le capot de l’appareil ni
démonter le panneau arrière. L’intérieur de l’appareil
ne possède aucun élément réparable par l’utilisateur.
Laissertoute réparation à un professionnel qualié.
Attention
Pour réduire les risques de feu et de choc
électrique, n’exposez pas cet appareil à la
pluie, à la moisissure, aux gouttes ou aux éclaboussures.
Ne posez pas de récipient contenant un liquide sur
l’appareil (un vase par exemple).
Attention
Ces consignes de sécurité et d’entretien
sont destinées à un personnel qualié.
Pouréviter tout risque de choc électrique, n’eectuez
aucune réparation sur l’appareil qui ne soit décrite par le
manuel d’utilisation. Les éventuelles réparations doivent
être eectuées uniquement par un technicien spécialisé.
1. Lisez ces consignes.
2. Conservez ces consignes.
3. Respectez tous les avertissements.
4. Respectez toutes les consignes d’utilisation.
5. N’utilisez jamais l’appareil à proximité d’un liquide.
6. Nettoyez l’appareil avec un chion sec.
7. Veillez à ne pas empêcher la bonne ventilation de
l’appareil via ses ouïes de ventilation. Respectezles
consignes du fabricant concernant l’installation
del’appareil.
8. Ne placez pas l’appareil à proximité d’une source
de chaleur telle qu’un chauage, une cuisinière ou tout
appareil dégageant de la chaleur (y compris un ampli
depuissance).
9. Ne supprimez jamais la sécurité des prises bipolaires
ou des prises terre. Les prises bipolaires possèdent deux
contacts de largeur diérente. Leplus large est le contact
de sécurité. Les prises terre possèdent deux contacts plus
une mise à la terre servant de sécurité. Si la prise du bloc
d’alimentation ou du cordon d’ali-mentation fourni ne
correspond pas à celles de votre installation électrique,
faites appel à un électricien pour eectuer le changement
de prise.
10. Installez le cordon d’alimentation de telle façon
que personne ne puisse marcher dessus et qu’il soit
protégé d’arêtes coupantes. Assurez-vous que le cordon
d’alimentation est sufsamment protégé, notamment au
niveau de sa prise électrique et de l’endroit où il est relié à
l’appareil; cela est également valable pour une éventuelle
rallonge électrique.
11. Utilisez exclusivement des accessoires et des
appareils supplémentaires recommandés par lefabricant.
12. Utilisez
exclusivement des
chariots, des diables,
desprésentoirs, despieds
et des surfaces de
travail recommandés
par le fabricant ou
livrés avec le produit.
Déplacezprécautionneusement tout chariot ou diable
chargé pour éviter d’éventuelles blessures en cas dechute.
13. Débranchez l’appareil de la tension secteur en cas
d’orage ou si l’appareil reste inutilisé pendant une longue
période de temps.
14. Les travaux d’entretien de l’appareil doivent
être eectués uniquement par du personnel qualié.
Aucunentretien n’est nécessaire sauf si l’appareil est
endommagé de quelque façon que ce soit (dommagessur
le cordon d’alimentation ou la prise par exemple), siun
liquide ou un objet a pénétré à l’intérieur du châssis,
si l’appareil a été exposé à la pluie ou à l’humidité, s’il ne
fonctionne pas correctement ou à la suite d’une chute.
15. L’appareil doit être connecté à une prise secteur
dotée d’une protection par mise à la terre.
16. La prise électrique ou la prise IEC de tout appareil
dénué de bouton marche/arrêt doit rester accessible
enpermanence.
17. Mise au rebut appropriée de
ce produit: Ce symbole indique
qu’en accord avec la directive DEEE
(2012/19/EU) et les lois en vigueur
dans votre pays, ce produit ne doit
pas être jeté avec les déchets
ménagers. Ce produit doit être
déposé dans un point de collecte agréé pour le recyclage
des déchets d’équipements électriques et électroniques
(EEE). Une mauvaise manipulation de ce type de déchets
pourrait avoir un impact négatif sur l’environnement et la
santé à cause des substances potentiellement
dangereuses généralement associées à ces équipements.
En même temps, votre coopération dans la mise au rebut
de ce produit contribuera à l’utilisation ecace des
ressources naturelles. Pour plus d’informations sur
l’endroit où vous pouvez déposer vos déchets
d’équipements pour le recyclage, veuillez contacter votre
mairie ou votre centre local de collecte des déchets.
18. N’installez pas l’appareil dans un espace conné tel
qu’une bibliothèque ou meuble similaire.
19. Ne placez jamais d’objets enammés, tels que des
bougies allumées, sur l’appareil.
20. Gardez à l’esprit l’impact environnemental lorsque
vous mettez des piles au rebus. Les piles usées doivent
être déposées dans un point de collecte adapté.
21. Utilisez l’appareil dans un climat tropical
et/ou modéré.
Music Tribe ne peut être tenu pour responsable pour
toute perte pouvant être subie par toute personne
se ant en partie ou en totalité à toute description,
photographie ou armation contenue dans ce
document. Les caractéristiques, l’apparence et d’autres
informations peuvent faire l’objet de modications
sans notication. Toutes les marques appartiennent
à leurs propriétaires respectifs. Midas, Klark Teknik,
Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic,
TC Helicon, Behringer, Bugera et Coolaudio sont
des marques ou marques déposées de Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd.
2019 Tous droits réservés.
Pour connaître les termes et conditions de garantie
applicables, ainsi que les informations supplémentaires
et détaillées sur la Garantie Limitée de Music Tribe,
consultez le site Internet musictribe.com/warranty.
Vorsicht
Die mit dem Symbol markierten
Anschlüsse führen so viel Spannung,
dassdie Gefahr eines Stromschlags besteht.
Verwenden Sie nur hochwertige, professionelle
Lautsprecherkabel mit vorinstallierten 6,35 mm
MONO-Klinkensteckern oder Lautsprecherstecker
mit Drehverriegelung. Alle anderen Installationen
oder Modikationen sollten nur von qualiziertem
Fachpersonal ausgeführt werden.
Achtung
Um eine Gefährdung durch Stromschlag
auszuschließen, darf die Geräteabdeckung
bzw. Geräterückwand nicht abgenommen werden.
ImInnern des Geräts benden sich keine vom Benutzer
reparierbaren Teile. Reparaturarbeiten dürfen nur von
qualiziertem Personal ausgeführt werden.
Achtung
Um eine Gefährdung durch Feuer bzw.
Stromschlag auszuschließen, darf dieses
Gerät weder Regen oder Feuchtigkeit ausgesetzt werden
noch sollten Spritzwasser oder tropfende Flüssigkeiten
in das Gerät gelangen können. Stellen Sie keine mit
Flüssigkeit gefüllten Gegenstände, wie z. B. Vasen,
aufdasGerät.
Achtung
Die Service-Hinweise sind nur durch
qualiziertes Personal zu befolgen.
Umeine Gefährdung durch Stromschlag zu vermeiden,
führen Sie bitte keinerlei Reparaturen an dem Gerät
durch, die nicht in der Bedienungsanleitung beschrieben
sind. Reparaturen sind nur von qualiziertem
Fachpersonaldurchzuführen.
1. Lesen Sie diese Hinweise.
2. Bewahren Sie diese Hinweise auf.
3. Beachten Sie alle Warnhinweise.
4. Befolgen Sie alle Bedienungshinweise.
5. Betreiben Sie das Gerät nicht in der Nähe vonWasser.
6. Reinigen Sie das Gerät mit einem trockenen Tuch.
7. Blockieren Sie nicht die Belüftungsschlitze. Beachten
Sie beim Einbau des Gerätes die Herstellerhinweise.
8. Stellen Sie das Gerät nicht in der Nähe von
Wärmequellen auf. Solche Wärmequellen sind z. B.
Heizkörper, Herde oder andere Wärme erzeugende Geräte
(auch Verstärker).
9. Entfernen Sie in keinem Fall die
Sicherheitsvorrichtung von Zweipol- oder geerdeten
Steckern. Ein Zweipolstecker hat zwei unterschiedlich
breite Steckkontakte. Ein geerdeter Stecker hat zwei
Steckkontakte und einen dritten Erdungskontakt.
Derbreitere Steckkontakt oder der zusätzliche
Erdungskontakt dient Ihrer Sicherheit. Falls das
mitgelieferte Steckerformat nicht zu Ihrer Steckdose
passt, wenden Sie sich bitte an einen Elektriker, damit die
Steckdose entsprechend ausgetauscht wird.
10. Verlegen Sie das Netzkabel so, dass es vor
Tritten und scharfen Kanten geschützt ist und nicht
beschädigt werden kann. Achten Sie bitte insbesondere
im Bereich der Stecker, Verlängerungskabel und an
der Stelle, an der das Netzkabel das Gerät verlässt,
aufausreichendenSchutz.
11. Das Gerät muss jederzeit mit intaktem Schutzleiter
an das Stromnetz angeschlossen sein.
12. Sollte der Hauptnetzstecker oder eine
Gerätesteckdose die Funktionseinheit zum Abschalten
sein, muss diese immer zugänglich sein.
13. Verwenden Sie nur Zusatzgeräte/Zubehörteile,
dielaut Hersteller geeignet sind.
14. Verwenden
Sie nur Wagen,
Standvorrichtungen,
Stative, Halter oder Tische,
die vom Hersteller benannt
oder im Lieferumfang
des Geräts enthalten
sind. Falls Sie einen
Wagen benutzen, seien Sie vorsichtig beim Bewegen
der Wagen- Gerätkombination, umVerletzungen durch
Stolpern zuvermeiden.
15. Ziehen Sie den Netzstecker bei Gewitter oder wenn
Sie das Gerät längere Zeit nicht benutzen.
16. Lassen Sie alle Wartungsarbeiten nur von
qualiziertem Service-Personal ausführen. EineWartung
ist notwendig, wenn das Gerät in irgendeiner Weise
beschädigt wurde (z. B. Beschädigung des Netzkabels oder
Steckers), Gegenstände oder Flüssigkeit in das Geräteinnere
gelangt sind, das Gerät Regen oder Feuchtigkeit ausgesetzt
wurde, das Gerät nicht ordnungsgemäß funktioniert oder
auf den Boden gefallen ist.
17. Korrekte Entsorgung dieses
Produkts: Dieses Symbol weist
darauf hin, das Produkt
entsprechend der WEEE Direktive
(2012/19/EU) und der jeweiligen
nationalen Gesetze nicht
zusammen mit Ihren
Haushaltsabfällen zu entsorgen. DiesesProdukt sollte bei
einer autorisierten Sammelstelle für Recycling elektrischer
und elektronischer Geräte (EEE) abgegeben werden.
Wegen bedenklicher Substanzen, diegenerell mit
elektrischen und elektronischen Geräten in Verbindung
stehen, könnte eine unsachgemäße Behandlung dieser
Abfallart eine negative Auswirkung auf Umwelt und
Gesundheit haben. Gleichzeitig gewährleistet Ihr Beitrag
zur richtigen Entsorgung dieses Produkts die eektive
Nutzung natürlicher Ressourcen. Fürweitere
Informationen zur Entsorgung Ihrer Geräte bei einer
Recycling-Stelle nehmen Sie bitte Kontakt zum
zuständigen städtischen Büro, Entsorgungsamt oder zu
Ihrem Haushaltsabfallentsorgerauf.
18. Installieren Sie das Gerät nicht in einer beengten
Umgebung, zum Beispiel Bücherregal oder ähnliches.
19. Stellen Sie keine Gegenstände mit oenen
Flammen, etwa brennende Kerzen, auf das Gerät.
20. Beachten Sie bei der Entsorgung von Batterien
den Umweltschutz-Aspekt. Batterien müssen bei einer
Batterie-Sammelstelle entsorgt werden.
21. Verwenden Sie das Gerät in tropischen und/oder
gemäßigten Klimazonen.
Music Tribe übernimmt keine Haftung für Verluste,
die Personen entstanden sind, die sich ganz oder
teilweise auf hier enthaltene Beschreibungen,
Fotos oder Aussagen verlassen haben. Technische Daten,
Erscheinungsbild und andere Informationen können
ohne vorherige Ankündigung geändert werden.
Alle Warenzeichen sind Eigentum der jeweiligen
Inhaber. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon,
Behringer, Bugera und Coolaudio sind Warenzeichen
oder eingetragene Warenzeichen der Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd.
2019 Alle Rechte vorbehalten.
Die geltenden Garantiebedingungen und zusätzliche
Informationen bezüglich der von Music Tribe gewährten
beschränkten Garantie nden Sie online unter
musictribe.com/warranty.
6 PCI SUB IW Quick Start Guide 7
¼" TS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Music Tribe
Midas Klark Teknik Lab Gruppen
Lake Tannoy Turbosound TC Electronic
TC Helicon Behringer Bugera Coolaudio
Music Tribe Global Brands Ltd.
© Music Tribe Global Brands Ltd.
2019
Music Tribe
musictribe.com/warranty
Instruções de Segurança
Importantes
LEGAL RENUNCIANTE
GARANTIA LIMITADA
Aviso!
Terminais marcados com o símbolo
carregam corrente elétrica de magnitude
suciente para constituir um risco de choque elétrico.
Use apenas cabos de alto-falantes de alta qualidade
com plugues TS de ¼" ou plugues com trava de torção
pré-instalados. Todas as outras instalações e modicações
devem ser efetuadas por pessoasqualicadas.
Este símbolo, onde quer que o encontre,
alerta-o para a leitura das instruções de
manuseamento que acompanham o
equipamento. Por favor leia o manual de instruções.
Atenção
De forma a diminuir o risco de choque
eléctrico, não remover a cobertura
(ouasecção de trás). Não existem peças substituíveis por
parte do utilizador no seu interior. Para esse efeito recorrer
a um técnico qualicado.
Atenção
Para reduzir o risco de incêndios ou
choques eléctricos o aparelho não deve ser
exposto à chuva nem à humidade. Além disso, não deve
ser sujeito a salpicos, nem devem ser colocados em cima
do aparelho objectos contendo líquidos, tais como jarras.
Atenção
Estas instruções de operação devem ser
utilizadas, em exclusivo, por técnicos de
assistência qualicados. Para evitar choques eléctricos
não proceda a reparações ou intervenções, que não as
indicadas nas instruções de operação, salvo se possuir as
quali-cações necessárias. Para evitar choques eléctricos
não proceda a reparações ou intervenções, que não as
indicadas nas instruções de operação. Só o deverá fazer se
possuir as qualicações necessárias.
1. Leia estas instruções.
2. Guarde estas instruções.
3. Preste atenção a todos os avisos.
4. Siga todas as instruções.
5. Não utilize este dispositivo perto de água.
6. Limpe apenas com um pano seco.
7. Não obstrua as entradas de ventilação. Instale de
acordo com as instruções do fabricante.
8. Não instale perto de quaisquer fontes de calor
tais como radiadores, bocas de ar quente, fogões de
sala ou outros aparelhos (incluindo amplicadores)
que produzam calor.
9. Não anule o objectivo de segurança das chas
polarizadas ou do tipo de ligação à terra. Uma cha
polarizada dispõe de duas palhetas sendo uma mais larga
do que a outra. Uma cha do tipo ligação à terra dispõe
de duas palhetas e um terceiro dente de ligação à terra.
A palheta larga ou o terceiro dente são fornecidos para
sua segurança. Se a cha fornecida não encaixar na sua
tomada, consulte um electricista para a substituição da
tomada obsoleta.
10. Proteja o cabo de alimentação de pisadelas ou
apertos, especialmente nas chas, extensões, e no local
de saída da unidade. Certique-se de que o cabo eléctrico
está protegido. Verique particularmente nas chas, nos
receptáculos e no ponto em que o cabo sai doaparelho.
11. O aparelho tem de estar sempre conectado à rede
eléctrica com o condutor de protecção intacto.
12. Se utilizar uma cha de rede principal ou uma
tomada de aparelhos para desligar a unidade de
funcionamento, esta deve estar sempre acessível.
13. Utilize apenas ligações/acessórios especicados
pelofabricante.
14. Utilize apenas com
o carrinho, estrutura,
tripé, suporte, ou mesa
especicados pelo
fabricante ou vendidos
com o dispositivo.
Quandoutilizar um
carrinho, tenha cuidado ao
mover o conjunto carrinho/dispositivo para evitar danos
provocados pela terpidação.
15. Desligue este dispositivo durante as trovoadas
ou quando não for utilizado durante longos períodos
detempo.
16. Qualquer tipo de reparação deve ser sempre
efectuado por pessoal qualicado. É necessária uma
reparação sempre que a unidade tiver sido de alguma
forma danicada, como por exemplo: no caso do cabo
de alimentação ou cha se encontrarem danicados;
naeventualidade de líquido ter sido derramado ou
objectos terem caído para dentro do dispositivo; no caso
da unidade ter estado exposta à chuva ou à humidade;
seesta não funcionar normalmente, ou se tiver caído.
17. Correcta eliminação deste
produto: este símbolo indica que
o produto não deve ser eliminado
juntamente com os resíduos
domésticos, segundo a Directiva
REEE (2012/19/EU) e a legislação
nacional. Este produto deverá
ser levado para um centro de recolha licenciado para a
reciclagem de resíduos de equipamentos eléctricos e
electrónicos (EEE). O tratamento incorrecto deste tipo
de resíduos pode ter um eventual impacto negativo
no ambiente e na saúde humana devido a substâncias
potencialmente perigosas que estão geralmente
associadas aos EEE. Ao mesmo tempo, a sua colaboração
para a eliminação correcta deste produto irá contribuir
para a utilização eciente dos recursos naturais. Paramais
informação acerca dos locais onde poderá deixar o seu
equipamento usado para reciclagem, é favor contactar
os serviços municipais locais, a entidade de gestão de
resíduos ou os serviços de recolha de resíduosdomésticos.
18. Não instale em lugares connados, tais como
estantes ou unidades similares.
19. Não coloque fontes de chama, tais como velas
acesas, sobre o aparelho.
20. Favor, obedecer os aspectos ambientais de descarte
de bateria. Baterias devem ser descartadas em um ponto
de coletas de baterias.
21. Use este aparelho em climas tropicais
e/ou moderados.
O Music Tribe não se responsabiliza por perda alguma
que possa ser sofrida por qualquer pessoa que dependa,
seja de maneira completa ou parcial, de qualquer
descrição, fotograa, ou declaração aqui contidas.
Dados técnicos, aparências e outras informações estão
sujeitas a modicações sem aviso prévio. Todas as
marcas são propriedade de seus respectivos donos.
Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy,
Turbosound, TC Electronic, TC Helicon, Behringer,
Bugera e Coolaudio são marcas ou marcas registradas
do Music Tribe Global Brands Ltd. © Music Tribe Global
Brands Ltd. 2019 Todos direitos reservados.
Para obter os termos de garantia aplicáveis e condições e
informações adicionais a respeito da garantia limitada do
Music Tribe, favor vericar detalhes na íntegra através do
website musictribe.com/warranty.
8 PCI SUB IW Quick Start Guide 9
ࣝధ൦ಗ঄ᄋጽቬ᝻ܭЧధृ
ܹᄋႄุߜڛᝐႄԁᬘǎ̪ᬎ
Ώၺࣝధ ¼'' TSੌ੶ᩛऱତ݁
ᄋᰵַ᠐˅ˋੵܧ٩ጴǎ੟ధᄋ߸ᜊੌួ
஠ڪᮍႁՍಬᄋ˅ˋ̢ցᤊᛢǎ
൦ಗ঄ଣᧉ১ַ̘аߜڛఴ
ፑᎇᄋԁᬘႄԎధᝐႄԁᬘǎ
൦ಗ঄ଣᧉ১ಋ᫟੟ᬅᄋ᧙᜷
ᄋΏၺԤ፦οឮ௛ǎឱ᫟឵ధ
У੥гǎ
࠶ॸ
˟ᥙГᝐႄԁᬘឱӉ੫ऩ఼
ᮈᄧੌᑁ᭨૖ౝǎ᝻ܭа෦
ధԼΚၺਜ਼፦οΏၺᄋᦋ͉ǎឱ࠳፦ο̄
ᮋ̕ႁՍಬᄋ˅ˋ̢ցᤊᛢǎ
࠶ॸ
˟ᥙГᅍ༣ੌᝐႄԁᬘឱӉ
࠳൦᝻ܭᎷ̇ᭂ๹ੌ໾ິ˘ǎ
൦᝻ܭ˸ˁԼԫ๰͵໠ຶᄪధ๰͵ᄋࠕ
٩˸ˁԼᎷ̇Цʾݡᔊၬ኏ǎ
࠶ॸ
፦οឮ௛̪௨ፍՍಬᄋ˅ˋ፦
ο̢ցΏၺᄋǎ˟ᥙГᝐႄԁ
ᬘᬕ́Ώၺឮ௛˻ଣ҃ᄋ̀ܲឱӉᤊᛢ
͋ͶЦ߳፦οǎ੟ధ፦οڪᮍႁՍಬᄋ˅
ˋ̢ցᤊᛢǎ
1. ឱ᫟឵ᤉ̐ឮ௛ǎ
2. ឱݱؔεߜᤉ̐ឮ௛ǎ
3. ឱญਔ੟ధᄋ᝞ᇩǎ
4. ឱᥗ߷੟ధᄋឮ௛ǎ
5. ឱӉڛ᭦ᤄබᄋڢஶΏၺశַ̘ǎ
6. ឱၺࣱ࣌ຎพశַ̘ǎ
7. ឱӉ܅܌ᤱ᮴Աǎ߸ᜊశַ̘௒ឱᥗ
ཱིԉࠓᄋឮ௛ǎ
8. ឱӉ࠳శַ̘߸ᜊڛམ຺ᬅᤄ
ݡ఍ජྠ༰ߖੌЦ̘߳ၸམ᧛ᄋ᝻ܭ
Ӌ઻ҫ஋٩ǎ
9. ឱӉሩᬕ౞মତ݁ੌ଍ڢତ݁ᄋ߸М
ᜊᎷǎ଍ڢତ݁௨ႁˑ˕ତ܌଍གྷԤʸ˕
଍ڢ݁౟ੈǎᔫᬥ᠏ଣΚᄋତ݁ˁᤡՍ১
ᄋତऑឱ੾ႄࢻట૲ʸ˕Սᤡᄋତऑǎ
10. ݱؔεઑႄ຺ጴΏЦˁᜃ᡼ᢇੌ҉
ᆢࡀЦญਔႄ຺ତ݁Ǎܴၺ᤮ତऑԤ᝻ܭ
ᤍ଍ܬǎ
11. ឱԷΏၺԉࠓ૊ࠁᄋᬅ࡜᝻ܭ֘
ᦢ͉ǎ
12. ឱԷΏၺԉࠓ
૊ࠁᄋੌᬥ᠏ᩚ
׭ᄋ੥ଏᢽ౷ߖ
ʽᝉ౷஄౷֘ಹ
ߖǎᔫΏၺ੥ଏᢽ
౐ୄᤃ᝻ܭឱญ
ਔ߸М஋Ꮇ᝻ܭ
̀ᥙГ੥ଏᢽ֘᝻
ܭϛωᏬԫ͟ǎ
13. ᥆᫆ႄᭈᲟੌ᫃ఱˁΏၺశ᝻ܭ௒
ឱફѤႄ຺ତ݁ǎ
14. ੟ధ፦οڪᮍႁՍಬᄋ፦ο̢ցᤊ
ᛢǎ᝻ܭԫ૰௒ᭋᤊᛢ፦οΔݡႄ຺ጴੌ
ႄ຺ତ݁ԫ૰๰͵ุЛੌफྮᗁЛ᝻ܭ
а᝻ܭᥔᭂ๹ੌԫ໾᝻ܭˁᑠ൥ࣣᤃͼ
ੌᜃ୒گǎ
15. శ᝻ܭᤍ଍ႄ຺௒ʸࠁ᜷ధ଍ڢ
εઑǎ
16. ᔫႄ຺ତ݁ੌ٩Ч
ᏺՍ٩ၺͼளႄᜊᎷ
अैε᝾߳̈́ܬ̇ᬥ௒Լ
ஶΨ୳ͼ࿅ঘǎ
17. శַ̘̪ᤡၺ̇๓
ફ2000ዜ̀ʿڢӞశ̘
ַ̪ᤡၺ̇᭥མࣝජό౏
͉ʿǎ
ࠬ̇͋Ͷڃڛ൦ឮ௛˻ଣ҃ᄋМᦋੌᦋ͌
ଢᤙǍڐྠੌܧ௛Ꮼᤶੈᄋ૰݀
Music Tribe
ˁ᠈͋Ͷ᠋͋ǎ઀సԡஞ֘ܲ᜻ᔫధటஉ
িˁԴᛢᤱᅽǎ੟ధᄋ׹ಗڪ˟ЦՋᒮ੟
ధᏩᄋ᠊̘ǎ
Midas, Klark Teknik, Lab Gruppen,
Lake, Tannoy, Turbosound, TC Electronic, TC Helicon,
Behringer, Bugera
֘ Coolaudio ௨Music Tribe
Global Brands Ltd.
ОՄᄋ׹ಗੌญг׹ಗǎ
© Music Tribe Global Brands Ltd. 2019ྡీ੟ధǎ
ధУᮄˮᬸڅεοᄋᤡၺ౏൝ԤЦ߳ᄲУ
θ্ឱᄇᬇmusictribe.com/warrantyᎫቤಋ
ᄻߺ஠ᄋឡጻθ্ǎ
Introduction
Thank you for purchasing this Tannoy premium dual 8" wall mount subwoofer for installation applications and the pre-construction wood back can installation kit.
Tannoy speaker systems are monitor-quality speaker systems based on the company's expertise in the manufacture of premium quality cabinet loudspeakers and
studio monitors. Exclusive drive unit designs and wide bandwidth technology ensure that these loudspeakers deliver the performance that is essential for applications
such as multi-room distributed audio installations, home theatre systems and discrete audio systems, as well as in the many other applications
where space is at a
premium but ultimate sound quality is still paramount. The speaker construction is based around a rigid moulded ABS baffle with excellent structural integrity; this,
when combined with the secure polycarbonate clamp mounting system, ensures a performance-enhancing rigid acoustic coupling with the wall surface, and an
immensely stable platform for the drivers to deliver optimum performance. Complementing any style of decor, the perforated metal grille and low profile mounting
frame can be painted to blend in seamlessly with the domestic environment. The result is a system offering audiophile quality sound with minimal invasion of the
living space.
Unpacking
Every Tannoy product is carefully inspected before shipment. After unpacking, please inspect your product to ensure no damage has occurred in transit.
In the unlikely event of damage, please notify your dealer and retain all shipping materials as your dealer may require return shipment.
Safety Notices
Tannoy will not be held responsible for any damages caused by the improper installation of these loudspeakers.
其他的重要信息
10 PCI SUB IW Quick Start Guide 11
Product Feature Identi cation Product Feature Identi cation
Mounting Clamps (x6)
Screws (crosshead X6)
for extending the
mounting clamps
Screws (hex X6)
for mounting
speaker assembly
into frame
Installation Template
Paint Mask
Back Can Assembly
Cable Entry for
Speaker Wire
Adjustable
Mounting Brackets
(X4)
Wood
Construction
Aperture
Screw terminals for
speaker wires
Subwoofer Assembly
Grille Installed Subwoofer and Frame Assembly
Frame Assembly
12 PCI SUB IW Quick Start Guide 13
Installation Guide
Back Can Installation
WARNING: This procedure requires the use of an assistant, and the use of personal protection equipment, such as safety glasses and gloves.
WARNING: To avoid potential damage to your loudspeaker, ensure that the power ampli er is switched OFF prior to connecting or disconnecting any cables.
WARNING: Make
sure that there are no power lines, other cables, or plumbing such as water, sewer, gas lines in the chosen location.
The procedure below describes the installation of the back can into a typical 2" x 4" stud wall with 16" centers, with sheetrock/plasterboard not yet installed.
After the back can and sheetrock is installed, the PCI SUB subwoofer frame can be installed, and the paint mask added.
T
he subwoofer assembly can be wired and added after the wall painting and finishing is complete.
6. Install the speaker wire in through the cable gland, and leave enough slack
to make the connections to the subwoofer assembly when that time comes
(Fig. 3). Tighten the cable gland, and tie down the speaker cable to prevent it
moving and rattling in operation. Make sure that the speaker cable does not
come into contact with nails or screws that might damage the insulation.
7. The installation of sheetrock around the back can location is best done using
a single large sheet with the vertical
center line centered over the back can
vertical centerline (Fig. 4). Use adhesive on the wall studs and on the front face
of the back can, and install the sheetrock using sheetrock screws into the wall
studs, spaced approximately 8 to 10 inches apart. This will help prevent wall
rattling and sheetrock movement and noises during operation. If the back can
is being installed on an interior wall, then adhesive and extra screws may also
be added to the sheetrock used in the room behind the back can. CAUTION:
Make sure that no sheetrock screws go into the wooden case of the back can at
any point.
8. After sheetrock installation, carefully cut out the hole in the sheetrock with
a suitable handtool, using the subwoofer aperture in the back can as a guide
(Fig. 5). Be careful not to cut the speaker wires. Make sure the sheetrock
aperture is no larger than the aperture of the back can. Remove any dust or
debris from within the back can.
Procedure
Follow the procedure steps below in the order in which they are presented.
Read all the instructions before starting.
1. Locate a suitable mounting position for the subwoofer that will o er optimum
acoustic performance for the listening environment and audio system, and that
is also practical and aesthetically pleasing.
2. With the help of an assistant, carefully move the back can to the chosen
location between the wall studs, and lift it to the correct height, allowing
enough room for the speaker wire to enter the bottom cable gland, and
with enough room to tighten the screws that hold the brackets to the
back can (Fig. 1).
3. Make sure that the front face of the back can is ush with the front face of
the wall studs.
4. Adjust the sliding brackets of the back can to t the width between
the studs (Fig.2).
5. Make sure that the back can is plumb and level, then screw the 4 brackets
to the wall studs using 2 screws per bracket. Tighten the screws holding the
brackets to the back can.
Fig. 1 Install the Back can between the studwork
Fig. 2 Adjust the sliding brackets to touch the studs on either side.
Fig. 3. Speaker Wire Installation.
Fig. 4. Sheetrock Screws.
Fig. 5. Sheetrock Removed from the Aperture.
Speaker Wire
14 PCI SUB IW Quick Start Guide 15
Procedure
1. The subwoofer assembly includes 2 drivers mounted on a rectangular ba e,
with the wiring and speaker wire screw terminals. The subwoofer assembly is
shipped from the factory already tted into the mounting frame. To separate the
subwoofer assembly from the mounting frame, undo 6 hex screws and remove the
subwoofer assembly from the frame (Fig. 8). CAUTION: The subwoofer assembly
only ts into the frame in one way. The TANNOY brand name is at the bottom and
the frame is marked "TOP" on the rear.
2. Use a crosshead screw driver to undo the 6 mounting clamp screws on the
mounting frame, to move the mounting clamps into their rest position (Fig. 9). In
this postion, the mounting clamps are not extended.
3. With the clamps in their rest position, the frame may now be pressed into the
sheetrock aperture/back can (Fig. 10). Orient the frame so that the edge marked
TOP on the rear side is at the top. Make sure the speaker wires are not pinched by
the frame.
4. Tighten the mounting clamp screws clockwise to extend the mounting clamps
and secure the frame to the back can/sheetrock (Fig. 11). Start at one corner then
move to the opposite corner, tightening su ciently to check for visual orientation,
before proceeding to tighten the other two corners. Finish o by tightening the
middle clamps.
WARNING: Do not over tighten the screws - this is unnecessary
to achieve a strong acoustic seal to the back can or wall, and risks damage
.
Alternative Installation without the Back Can
If you are not using the PCI SUB back can, then use the supplied template as a guide to cutting the sheetrock.
WARNING: This procedure requires the use of personal protection equipment, such as safety glasses and gloves.
WARNING: To avoid potential damage to your loudspeaker, ensure
that the power ampli er is switched OFF prior to connecting or disconnecting any cables.
WARNING: Make sure that there are no power lines, other cables, or plumbing such as water, sewer, gas lines in the chosen location.
The procedure below describes an installation in
a typical 2" x 4" stud wall with 16" centers, with sheetrock/plasterboard already installed.
After the sheetrock aperture is cut, the PCI SUB subwoofer frame can be installed, and the paint mask added.
T
he subwoofer assembly can be wired and added after the wall painting and finishing is complete.
Fig. 6. Installation Template.
Fig. 7. Sheetrock Removed from the Aperture.
Procedure
Follow the procedure steps below in the order in which they are presented.
Read all the instructions before starting.
1. Locate a suitable mounting position for the subwoofer that will o er optimum
acoustic performance for the listening environment and audio system, and that
is also practical and aesthetically pleasing.
2. Make sure the template is centered between wall studs that are spaced on
16 inch centers or more. This will allow room for the wall mount clamps to
operate freely.
3. Apply the template to the wall, and carefully drill the sheetrock in the 4
corners of the template, using a ½ " diameter drill. Carefully cut out the hole
in the sheetrock with a suitable handtool, following the template as a guide
(Fig. 6). Remove any dust or debris from within the cutout.
4. Install the speaker wire to this location, and leave enough slack to make
the connections to the subwoofer assembly when that time comes (Fig.7).
Tie down the speaker cable to prevent it moving and rattling in operation.
5. Use adhesive within the aperture to help secure the sheetrock to the nearby
wall studs, and if possible install extra sheetrock screws approximately 8 to 10
inches apart. This will help prevent wall rattling and sheetrock movement and
noises during operation. If the subwoofer is being installed on an interior wall,
then adhesive and extra screws may also be added to the sheetrock used in the
room behind the subwoofer.
Fig. 8. Undo hex screws to remove Subwoofer Assembly from Frame.
Fig. 9. Undo Mounting Clamp crosshead screws to stow Clamps.
Fig. 10. Press the Frame into the wall aperture. Fig. 11. Tighten Mounting Clamp Screws to extend Clamps.
Subwoofer Frame Installation
With the back can installed and the sheetrock cut as shown in the previous instructions, the speaker frame can be fitted into position. The procedure is the same if the
back can is used or not.
Top
Bottom
16 PCI SUB IW Quick Start Guide 17
Wall Clamp Mechanism
The clamping mechanism has been designed to provide an acoustically-optimum
bond to the wall surface without risk of distortion to the loudspeaker baffle.
As these screws are tightened, the immensely strong polycarbonate clamping
arms will automatically swing round into the locking position, locating the
subwoofer frame securely to the inside of the back can or wall surface (Fig. 12).
The design also allows for simple removal of the subwoofer frame.
The clamp mechanism ensures that as the screws are loosened
(turned anti-clockwise) the clamp arm travels along its guide before turning
itself into the rest position. The captive locking system ensures that the clamp
arm cannot drop off the end of the screw to be lost in the back can or wall cavity.
CAUTION: Move all the clamps in the rest position by loosening all screws before
attempting to remove the frame assembly from the wall.
Painting
Before proceeding with the installation of the subwoofer assembly into the
installed frame, the grille and frame trim edges can be painted to blend with the
surrounding decor.
It is strongly recommended that the metal perforated grille is sprayed, as this
will avoid clogging of the holes. If painting with a brush is the only option, then
several thin coats of paint will provide a superior finish to that achieved by one
applied too thickly.
The subwoofer is supplied with a paint mask.
1. Press the painting mask into the installed frame. This is left in place while the
wall and frame surround is painted (Fig. 13).
2. The painting mask can also be left in place to prevent dust and dirt
entering the back can or wall cavity, until the subwoofer assembly is ready
to be installed.
Subwoofer Installation into the Frame
With the subwoofer frame installed and the wall and frame finished and painted,
the subwoofer assembly can now be wired and installed into the frame.
Wiring
WARNING: To avoid potential damage to your loudspeaker, ensure that the
amplifier is switched OFF prior to connecting or disconnecting any cables.
WARNING: Before switching the amplifier ON, double check that all connections
are secure and that the polarity is correct.
We recommend the use of insulated speaker wiring of between 12 and 18 AWG.
1. Remove the paint mask from the frame and pull out the end of the speaker
cable. Strip o approximately 8 mm (¼ ") of the outer protective layer from
each conductor.
2. Hold the subwoofer assembly up close to the installed speaker frame.
3. Insert the speaker wires into the correct speaker terminals and secure the
connections with a small screwdriver. The positive wire from your ampli er
should go to the positive terminal marked (+). The negative wire from your
ampli er should connect to the negative terminal marked (-) (Fig.14).
4. Make sure that the speaker cable is secured so that it will not move and touch
the subwoofer cones in operation.
Subwoofer Installation
1. The subwoofer assembly can now be added into the frame, taking care not
to trap or pinch the speaker wiring, or your ngers (Fig. 15). The subwoofer
assembly only ts into the frame in one way. The Tannoy brand badge is at the
bottom and the top of the frame is marked "TOP" on the rear.
2. Secure the subwoofer assembly to the frame with the 6 hex screws. To remove
the subwoofer, undo these screws and make sure to support the weight of the
subwoofer assembly as it comes undone.
Grille Installation
1. The grille should be carefully tted by lining up the edges of the grille with the
ba e and frame inside edges (Fig. 16). To avoid indentation damage, do not
press the centre of the grille; apply even pressure to each corner as it is pressed
rmly into position.
2. To remove the grille, loop an opened paper clip or similar length of firm wire,
through two holes near a corner and pull gently. The grille is intended to be
a tight fit, so insert the wire at each corner in turn, pulling carefully to avoid
distortion of the mesh.
System Testing
1. Switch on the ampli er with the volume control at its lowest setting. Select
a suitable low frequency signal source and slowly turn up the volume to a
low level. Check that both subwoofer drivers are working correctly - if not,
switch o the ampli er and recheck the connections.
2. Carefully check the area surrounding the installation and listen carefully
to ensure that there are no buzzes or rattles that could potentially impair
enjoyment of the system. If there are, then locate and silence the causes using
cable ties, suitable packing material, or extra adhesive in areas.
Fig. 12. Mounting Clamps stowed position and extended.
Fig. 13. Paint Mask in place
Fig. 14. Wiring the Subwoofer
Fig. 15 . Installing the Subwoofer Assembly into the frame
Fig. 16. Installing the Grille into the frame
18 PCI SUB IW Quick Start Guide 19
DimensionsDimensions
**
WALL BOARD THICKNESS
ESTIMATION (12 mm, 0.47")
81,7 mm
[3.22"]
275,4 mm
[10.84"]
264,5 mm
[10.41"]
495,6 mm
[19.51"]
108,90 mm
[4.29"]
251,9 mm
[9.92"]
482,8 mm
[19.01"]
98,0 mm
[3.86"]
10,4 mm
[0.41"]
93,7 mm
[3.69"]
WALL BOARD FACE
1405,0 mm
[55.32"]
1465,0 mm
[57.68"]
345,0 mm
[13.58"]
482,5 mm
[19.00"]
252,5mm
[9.94"]
86,0 mm
[3.39"]
71,0 mm
[2.80"]
603,5mm
[23.76"]
563,5 mm
[22.19"]
Other important information
20 PCI SUB IW Quick Start Guide 21
1. Register online. Please register your new
Music Tribe equipment right after you purchase it by
visiting tannoy.com. Registering your purchase using our
simple online form helps us to process your repair claims
more quickly and e ciently. Also, read the terms and
conditions
of our warranty, if applicable.
2. Malfunction. Should your Music Tribe
Authorized Reseller not be located in your vicinity,
you may contact the Music Tribe Authorized Ful ller for
your country listed under “Support” at tannoy.com. Should
your country not be listed, please
check if your problem
can be dealt with by our “Online Support” which may also
be found under “Support” at tannoy.com. Alternatively,
please submit an online warranty claim at behringer.com
BEFORE returning the product.
Important information
Speci cations
Performance
Frequency response (±3 dB) 100 Hz – 2 kHz
Frequency response (-10 dB) 45 Hz – 2.3 kHz
Sensitivity (1 W @ 1m) 90 dB
Power handling (IEC)
Average 200 W
Programme 400 W
Peak 800 W
Recommended amplifier power 600 W @ 8 Ω
Nominal Impedance (Lo Z) 8 Ω
Rated maximum SPL (1 m, Lo Z) 116 dB
Average 113 dB
Peak 119 dB
Crossover point NA
Transducers
Low frequency diameter/material/type 2 x 219 mm (8")
Physic al
Back can BACK CAN PCI SUB IW Wood
Baffle Re ex loaded UL94 V-0 rated ABS
Grille Steel, with weather resistant coating
Clamping design Security toggle clamp
Connectors Phoenix Contact terminal block
Dimensions (H x W x D) 1465 x 345 x 113 mm (57.7 x 13.6 x 4.5")
Bezel dimensions 495.6 x 264.5 mm (19.5 x 10.4")
Mounting depth 93.1 mm
(3.7")
Hole cutout dimensions 482,5 x 252,5 mm (19 x 9.94")
Net weight 16.9 kg (37.2 lbs)
Packed quantity 1
Included accessories
PCI SUB IW: Grille, paint mask, cutout template .
BACK CAN PCI SUB IW: washers (x12), screws (x12), bracket (x4), cable clamp.
Optional accessories PCI SUB IW and Back Can PCI SUB IW are
also available separately
22 PCI SUB IW Quick Start Guide 23
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Tannoy PCI SUB IW WITH BACK CAN クイックスタートガイド

PCI SUB IW WITH BACK CAN
Tannoy
ブランド
Tannoy
モデル
PCI SUB IW WITH BACK CAN
カテゴリー
スピーカー
タイプ
クイックスタートガイド
PDFをダウンロードします
報告

他の言語で

関連論文

その他のドキュメント