www.blackanddecker.com
BPHR202
English 3
简体中文 8
E
F
C D
BA
* The picture above may differ slightly to actual unit.
3
9
10
9
11
4
4
8
7
4
13
14
12
6
5
2
3
1
3
ENGLISH
Intended use
Your Black and Decker SDS plus rotary hammer is intended to
drill holes in concrete, bricks, wood, and steel.
Safety instructions
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term power tool in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Rotary hammer BPHR202
Power input W 620
Voltage V 220
Frequency Hz 50
No-load speed /min 0-1250
Impact rate BPM 0-3900
Impact energy J 1.34
Modes 2
Max drilling capacity mm
- Concrete 20
- Steel 13
- Wood 25
Weight kg 2.6
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed
or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock. NOTE:
The term “residual current device (RCD)” may be replaced
by the term “ground fault circuit interrupter (GFCI)” or “earth
leakage circuit breaker (ELCB)”.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
BPHR202
Rotary hammer
Technical data
4
ENGLISH
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
* Note: Mains voltage: When connecting to the mains, it is
imperative to verify if the voltage of the mains matches that
of the power tool. If the mains voltage exceeds the voltage
indicated on the power tool, the user may become severely
injured in an accident, and the tool may be damaged. On
the contrary, if the mains voltage is lower than the voltage
required by the tool, the motor may be damaged as a result.
Thus, if it is not possible to verify the voltage, it is imperative
not to plug in to the power source.
Hammer safety warnings
u Wear ear protectors. Exposure to noise can cause hear-
ing loss.
u Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
uHold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a live wire may make exposed
metal parts of the power tool live and could give the
operator an electric shock.
u Never use a chisel accessory in rotary mode. The acces-
sory will bind in the material and rotate the drill.
u Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the work by
hand or against your body leaves it unstable and may lead
to loss of control.
u Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
u Avoid touching the tip of the drill bit after drilling so as to
avoid scalding.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance of
any operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.
Safety of others
u This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabili-
ties, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Other risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. In spite of the
application of the relevant safety regulations and the imple-
mentation of safety devices, certain risks cannot be avoided.
These are:
uInjuries caused by touching any rotating/moving parts.
uInjuries caused when changing any parts, blades or acces-
sories.
uInjuries caused by prolonged use of a tool. When using any
tool for prolonged periods ensure you take regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
5
ENGLISH
Labels on tool
The following symbols are shown on the tool:
:
WARNING! To reduce the risk of injury, the user must
read the instruction manual.
Position of Date Barcode (Fig. C)
The Date Code (12), which also includes the year of manufac-
ture, is printed into the housing.
Example
2014 XX JN
Year of manufacturing
Electrical Safety
Your tool is double insulated; therefore no earth wire is
required. Be sure to check that the power supply corre-
sponds to the voltage on the rating plate. Corresponds.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black and Decker Service
Centre in order to avoid a hazard.
Using an Extension Cable
If it is necessary to use an extension cable, please used an ap-
proved extension cable that fits the tool’s power input specifica-
tions (please refer to the technical data). The minimum cross-
sectional area of the conducting wire is 1.5 sq. mm. Cables
should be untangled before reeling up.
Please refer to the following table.
Cable cross-sectional area (mm
2
) Cable rated current (Ampere)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rated current (Ampere)
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Features (Fig. E)
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Mode selector
4. Tool clamp
5. Side handle
6. Depth stop
Assembly
WARNING! Before assembly, make sure that the tool is
switched off and unplugged.
Attaching the Side Handle (fig. E)
WARNING! When drilling holes in concrete or bricks, please
use the side handle for your safety.
u Turn the grip counterclockwise until you can slide the side
handle onto the front of the tool.
u Rotate the side handle into the desired position.
u Tighten the side handle by turning the grip clockwise.
WARNING! When using the tool, remember to install the side
handles properly.
Fitting an accessory (fig.A)
u Clean and grease the shank (7) of the accessory.
u Insert the accessory bar into the tool clamp(4).
u Push the accessory down and turn it slightly until it fits into
the slots.
u Pull on the accessory to check if it is properly locked. The
hammering and drilling function requires the accessory to
be able to move axially several centimetres when locked in
the tool clamp.
u To remove the accessory, pull back the sleeve (8) and pull
out the accessory from the tool clamp.
Use
WARNING! Please operate tool with normal load. Do not over-
load.
WARNING! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Selecting the Operating Mode (fig. B)
The tool can be used in two operating modes. Based on actual
work requirements, the drilling mode selector (3) can be rotated
to the required position.
Hole drilling (Fig. B) (Fig. F)
u For drilling in steel, wood and plastics, set the operating
mode selector (3) to the (
b
) position. At the same time, it
is necessary to use a suitable drill chuck (13) (optional ac-
cessory) to clamp the attachment rod.
6
ENGLISH
u Insert the drill chuck (13) into the tool chuck (4) accord-
ing to the instructions for installing attachments. Turn the
drill chuck to loosen the clamps at the front-end of the drill-
clamp, and insert the accessory bar (14) into the clamps
and turn the chuck in the opposite direction. You may also
use the drill chuck key to tighten the clamp.
Hammer drilling (Fig. B)
u For hammer drilling in masonry and concrete, set the oper-
ating mode selector (3) to the
s
position.
u The drill bit has to be placed accurately onto the drill hole
position. After that, pull the switch for optimal effects. Make
sure the tool is in the correct position to prevent the drill
from deviating from the hole.
u When the drill hole is clogged with debris or fine powder,
please don't exert any more pressure. Tool should be put in
free-running state before removing part of the drill bit from
the hole. If repeated a few times, the blockage in the hole
would be cleared, and normal drilling can resume.
WARNING! When the drill bit hits cement or the steel rebar in
the cement, the tool may recoil dangerously. Please hold the
tool tightly in a balanced and stable position at all times to pre-
vent it from recoiling dangerously.
Overload coupling device
If the drill bit his caught or hooked, the driving force transmitted
to the drill shaft will be cut off. This would generate a strong
recoil, so it would be necessary to hold the tool tightly with both
hands to remain in a stable position.
Setting the drilling depth (Fig. E)
The depth stop is a convenient feature to ensure uniformity
in drilling depth. Loosen the side handle to adjust the depth
gauge according to the required depth. After that, tighten the
side handle.
u Slacken the side handle (5) by turning the grip counter-
clockwise.
u Set the depth stop (6) to the required position. The maxi-
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
u Tighten the side handle by turning the grip clockwise.
Switching on and off
WARNING! Before plugging in to the power source, make sure
the switch can be flipped freely, and can return to its original
position once released.
uTo switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
uAs a general rule, use low speeds for large diameter drill
bits and high speeds for smaller diameter drill bits.
u For continuous operation, press the lock-on button (2) and
release the variable speed switch.
u To switch the tool off, release the variable speed switch. To
switch the tool off when in continuous operation, press the
variable speed switch once more and release it.
Accessories
The performance of your tool depends on the accessory used.
Black and Decker accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best from
your tool.
Maintenance
Your Black and Decker corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. To ensure satisfactory operations,
the tool must be maintained and cleaned regularly
WARNING! Before performing any maintenance on corded/
cordless power tools:
uSwitch off and unplug the appliance/tool.
uOr switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
uOr run the battery down completely if it is integral and then
switch off.
uUnplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
uRegularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
uRegularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Replace the carbon brush (Fig. D)
A
Lubrication
u Regularly replace and inspect the carbon brush. Once
completely worn out by continuous wear and tear, it will
have to be replaced. Must keep carbon brush clean and
sliding freely within the brush holder. Both carbon brushes
have to be replaced at the same time.
uRemove the fixed screws (9) on the carbon brush to re-
move the carbon brush (10) and brush holder.
uRemove the coil spring supporting the carbon brush (11) in
the brush holder, and insert a new carbon brush that meets
the specifications.
7
ENGLISH
uSet up the brush holder again and return the supporting coil
spring to its original position.
S
Cleaning
@
WARNING! Blow dirt and dust out of the main hous-
ing with dry air as often as dirt is seen collecting in
and around the air vents. Wear approved eye protec-
tion and approved dust mask when performing this
procedure.
@
WARNING! Never use solvents or other harsh chem-
icals for cleaning the non-metallic parts of the tool.
These chemicals may weaken the material of the
parts. Use only mild soap and damp cloth to clean
the tool. Never let any liquid get inside the tool; never
immerse any part of the tool into liquid.
Protecting The Environment
Separate collection. This product must not be dis-
posed of with normal household waste.
Should you find one day that your Black and Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Please sort it out for sepa-
rate recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent environmental
pollution and reduces the demand for raw materials.
Some local governments may require the local or municipal
waste disposal centers or retailers of new products to provide
households with electronic product recycling services.
8
SDS plus ,,
1.
a.
b.
c.
2.
BPHR202
W 620
V 220
Hz 50
/min 0-1250
BPM 0-3900
J 1.34
2
mm
- 20
- 13
- 25
kg 2.6
a.
b.
c.
d.
e.
f.
RCD RCD
3.
a.
b.
c. /
d.
e.
f.
g.
4.
a.
b.
c.
BPHR202
9
d.
e.
f.
g.
5.
a.
*
u
u
u
u
u
u
u
u
/
u
u
u/
u
u
u
u
:
C
(12)
2014 XX JN
u
10
( )
1.5
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
7.5 15 25 30 45 60
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
E
1.
2.
3.
4.
5.
6.
E
u
u
u
A
u (7)
u (4)
u
u
u (8)
B
(3)
B F
u
(3)
b
13
u13
4
14
B
u
(3)
s
u
u
E
11
u (5)
u (6)
u
u (1)
u
u (2)
u
/ /
/
u/
u /
/
u /
u
u/ /
u
u
D
A
u
u (9) (10)
u(11)
u
S
@
@
88
676A
N400245 05/2014
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
