Dell PowerSwitch N1100-ON Series クイックスタートガイド

Dell Networking

N1108T-ON/N1108P-ON/

N1108EP-ON/N1124T-ON/

N1124P-ON/N1148T-ON/

N1148P-ON Switches

Getting Started Guide

使用入门指南

入門指南

『はじめに』

설명서는

Regulatory Model: E17W and E18W

Regulatory Type: E17W001/E18W001/E18W002

Dell Networking

N1108T-ON/N1108P-ON/

N1108EP-ON/N1124T-ON/

N1124P-ON/N1148T-ON/

N1148P-ON Switches

Getting Started Guide

Regulatory Models: E17W and E18W

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your switch.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

Lithium battery caution:

• There is a danger of explosion if a battery is incorrectly replaced. Replace

only with the same or equivalent type. Dispose batteries of according to

the manufacturer's instructions.

• Disposing a battery into fire, a hot oven, mechanically crushing, or cutting

it can result in an explosion.

• Leaving a battery in an extremely hot environment can result in leakage of

flammable liquid, gas, or an explosion.

• If a battery is subjected to extremely low air pressure, it may result in

leakage of flammable liquid, gas, or an explosion.

• The device can only be used in a fixed location such as a lab or a machine

room. When you install the device, ensure that the protective earthing

connection of the socket-outlet is verified by a skilled person.

___________________

international copyright and intellectual property laws. Dell and the Dell logo are trademarks of Dell

Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein may

be trademarks of their respective companies.

Regulatory Models: E17W and E18W

May 2019 P/N JJHMV Rev. A01

Contents 3

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . 5

N1100-ON Series Hardware Overview . . . . . . . . . . 5

Power Consumption for N1100-ON Series

PoE Switches

. . . . . . . . . . . . . . . . . . . . . 5

Ventilation System

. . . . . . . . . . . . . . . . . . 6

N1100-ON Series Model Summary

. . . . . . . . . . . . 7

2 N1108T-ON/N1108P-ON/N1108EP-ON

Installation . . . . . . . . . . . . . . . . . . . . . . . . 8

Mounting an N1108T-ON/N1108P-ON Switch Using

Dell Tandem Tray . . . . . . . . . . . . . . . . . . . . . 8

Mounting an N1108T-ON/N1108P-ON/N1108EP-ON

on a Two-Post Rack Using Large L-brackets

. . . . . . . 9

Mounting all N11xx-ON Switches on a Wall

. . . . . . 10

3 N1124T-ON/N1124P-ON/N1148T-ON/

N1148P-ON Installation . . . . . . . . . . . . . . 13

Rack Mounting an N1124T-ON/N1124P-ON/

N1148T-ON/ N1148P-ON Switch. . . . . . . . . . . . . 13

Installing in a Rack

. . . . . . . . . . . . . . . . . 13

Installing as a Free-standing Switch . . . . . . . . 14

Stacking Multiple N1124T-ON/N1124P-ON/

N1148T-ON/ N1148P-ON Switches

. . . . . . . . . . . 14

4 Contents

4 Starting and Configuring the

N1100-ON Series Switch . . . . . . . . . . . . . 15

Connecting an N1100-ON Series Switch to

a Terminal . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting an N1100-ON Series Switch to

a Power Source

. . . . . . . . . . . . . . . . . . . . . 17

AC and DC Power Connection

. . . . . . . . . . . 17

Booting the N1100-ON Series Switch

. . . . . . . . . . 18

Performing the N1100-ON Series

Initial Configuration

. . . . . . . . . . . . . . . . . . . 19

Enabling Remote Management

. . . . . . . . . . . 19

Initial Configuration Procedure

. . . . . . . . . . . 20

Example Session . . . . . . . . . . . . . . . . . . 21

Dell Easy Setup Wizard Console Example

. . . . . 22

Next Steps

. . . . . . . . . . . . . . . . . . . . . 26

5 Agency compliance . . . . . . . . . . . . . . . . 28

6 Operating Altitude–Information Update 31

Getting Started Guide 5

Introduction

This document provides basic information about the Dell Networking

N1100-ON Series switches, including how to install a switch and perform the

initial configuration. For information about how to configure and monitor

switch features, refer to the User Configuration Guide, which is available on

the Dell Support website at dell.com/support. See the Support website for

the latest updates on documentation and firmware.

NOTE: Switch administrators are strongly advised to maintain Dell Networking

switches on the latest version of the Dell Networking Operating System (DNOS).

Dell Networking continually improves the features and functions of DNOS based on

feedback from you, the customer. For critical infrastructure, pre-staging of the new

release into a non-critical portion of the network is recommended to verify network

configuration and operation with the new DNOS version.

N1100-ON Series Hardware Overview

This section contains information about device characteristics and modular

hardware configurations for the Dell Networking N1100-ON Series switch.

NOTE:

The N1108EP-ON switch uses an external power adaptor. There is no mounting kit

available for the N1108EP-ON external power adaptor. When installing the

N1108EP-ON, place the external power adaptor away from the switch.

Power Consumption for N1100-ON Series PoE Switches

Table 1-1 describes the power consumption for N1100-ON Series PoE

switches. The PoE power budget is 60W for the N1108P-ON, 123W for the

N1108EP-ON, 185W for the N1124P-ON, and 370W for the N1148P-ON.

Table 1-1. Power Consumption for N1100-ON Series PoE Switches

Model Input Voltage Power Supply

Configuration

Maximum Steady

Current

Consumption (A)

Maximum

Steady

Power (W)

N1108P-ON 100V/60Hz Main PSU 0.95A 88.64W

110V/60Hz Main PSU 0.87A 88.43W

120V/60Hz Main PSU 0.80A 88.22W

220V/50Hz Main PSU 0.49A 89.28W

240V/50Hz Main PSU 0.45A 89.70W

6 Getting Started Guide

Ventilation System

One fan cools the N1108T-ON/N1108P-ON switches, and two fans cool the

N1024T-ON/N1024P-ON/N1048T-ON/N1048P-ON switches. The fans are

not field replaceable. The N1108EP-ON is a fanless switch.

N1108EP-ON 100V/60Hz 54VDC External

power adaptor

1.62A 157W

110V/60Hz 54VDC External

power adaptor

1.47A 157W

120V/60Hz 54VDC External

power adaptor

1.35A 157W

220V/50Hz 54VDC External

power adaptor

0.74A 157W

240V/50Hz 54VDC External

power adaptor

0.67A 157W

N1124P-ON 100V/60Hz Main PSU 2.66A 260.66W

110V/60Hz Main PSU 2.38A 257.95W

120V/60Hz Main PSU 2.16A 256.27W

220V/50Hz Main PSU 1.18A 250.52W

240V/50Hz Main PSU 1.10A 251.25W

N1148P-ON 100V/60Hz Main PSU 4.78A 476.03W

110V/60Hz Main PSU 4.32A 472.64W

120V/60Hz Main PSU 3.95A 470.58W

220V/50Hz Main PSU 2.14A 459.37W

240V/50Hz Main PSU 1.97A 459.06W

Model Input Voltage Power Supply

Configuration

Maximum Steady

Current

Consumption (A)

Maximum

Steady

Power (W)

Getting Started Guide 7

N1100-ON Series Model Summary

Table 1-2. N1100-ON Series Switch Regulatory Numbers

Marketing

Model Name

(MMN)

Description Power Supply

Unit (PSU)

Regulatory

Model Number

(RMN)

Regulatory

Type Number

(RTN)

N1108T-ON 10x1G/2x1G SFP Ports DPS-24GP E17W E17W001

N1108P-ON 10x1G/2x1G SFP/2xPoE+ Ports DPS-80AP/

DPS-24GP

E17W E17W001

N1108EP-

ON

8x1G PoE+/2x1G PD/2x1G SFP

Ports

ADP-280BR E48W E48W001

N1124T-ON 24x1G/4x10G SFP+ Ports DPS-40AP E18W E18W001

N1124P-ON 24x1G/4x10G SFP+/6xPoE+ Ports EDPS-250BF E18W E18W001

N1148T-ON 48x1G/4x10G SFP+ Ports DPS-60AP E18W E18W002

N1148P-ON 48x1G/4x10G SFP+/12xPoE+ Port YM-2501D E18W E18W002

8 Getting Started Guide

N1108T-ON/N1108P-ON/N1108EP-

ON Installation

Mounting an N1108T-ON/N1108P-ON Switch

Using Dell Tandem Tray

The AC power connector is on the rear panel.

WARNING: Read the safety information in the

Safety and Regulatory Information

as well as the safety information for other switches that connect to or support the

switch.

WARNING: Do not use rack mounting kits to suspend the switch from under a

table or desk, or attach it to a wall.

CAUTION: Disconnect all cables from the switch before continuing. Remove all

self-adhesive pads from the underside of the switch, if they have been attached.

CAUTION: When mounting multiple switches into a rack, mount the switches

from the bottom up.

1

Secure the N1108T-ON/N1108P-ON switch in the Dell Tandem Tray Kit

as shown in Figure 1-1.

Figure 1-1. Dell Tandem Tray Kit

2

Insert the switch into the 48.26 cm (19 inch) rack, ensuring that the rack

mounting holes on the kit line up to the mounting holes in the rack.

Getting Started Guide 9

3

Secure the kit to the rack with either the rack bolts or cage nuts and cage-

nut bolts with washers (depending on the kind of rack you have). Fasten

the bolts on the bottom before fastening the bolts on the top.

Mounting an N1108T-ON/N1108P-ON/N1108EP-

ON on a Two-Post Rack Using Large L-brackets

NOTE: The AC power connector is on the rear panel of the N1108T-ON/N1108P-ON

switches. The DC power connector for the N1108EP-ON is at the center of the rear

panel.

NOTE: The N1108EP-ON switch uses an external power adaptor. There is no mounting kit

available for the N1108EP-ON external power adaptor. When installing the

N1108EP-ON, place the external power adaptor away from the switch.

CAUTION: As the N1108EP-ON is a fanless switch, do not place the external power

adaptor on top of the switch to avoid overheating.

1

Place the supplied rack-mounting bracket on one side of the switch

making sure that the mounting holes on the switch line up to the

mounting holes on the rack mounting bracket. See item 1 in Figure 1-2.

Figure 1-2. Installing Using Large L-bracket Kit

2

Insert the supplied screws into the rack mounting holes and tighten with a

screwdriver.

3

Repeat the process on the other side of the switch.

10 Getting Started Guide

4

Insert the switch and rail assembly into the rack from the front of the rack.

Make sure that the rack-mounting holes on the switch line up to the

mounting holes on the rack.

5

Secure the switch to the rack with the rack screws. Fasten the lower pair of

screws before the upper pair of screws. See Figure 1-3.

Figure 1-3. Install on a Two-post Rack with L-Bracket

Mounting all N11xx-ON Switches on a Wall

1

Make sure that the mounting location meets the following requirements:

• The surface of the wall can support the switch.

• The location is ventilated to prevent heat buildup.

2

Place the supplied wall-mounting bracket on one side of the switch,

verifying that the mounting holes on the switch line up to the mounting

holes on the wall-mounting bracket.

3

Insert the supplied screws into the wall-mounting bracket holes and

tighten with a screwdriver. See Figure 1-4.

Getting Started Guide 11

Figure 1-4. Inserting Mounting Brackets

4

Repeat the process for the wall-mounting bracket on the other side of the

switch.

5

Place the switch on the wall in the location where the switch is being

installed.

6

Mark the locations on the wall where the screws to hold the switch must be

prepared.

7

On the marked locations, drill the holes and place all the eight supplied

anchors in the holes.

8

Insert the supplied screws into the wall-mounting bracket holes and

tighten them with a screwdriver. See Figure 1-5.

12 Getting Started Guide

Figure 1-5. Mounting on a Wall

Getting Started Guide 13

N1124T-ON/N1124P-ON/N1148T-ON/

N1148P-ON Installation

Rack Mounting an N1124T-ON/N1124P-ON/

N1148T-ON/ N1148P-ON Switch

WARNING: Read the safety information in the

Safety and Regulatory Information

as well as the safety information for other switches that connect to or support the

switch.

The AC power connector is on the rear panel of the switch.

Installing in a Rack

WARNING: Do not use rack mounting kits to suspend the switch from under a

table or desk, or attach it to a wall.

CAUTION: Disconnect all cables from the switch before continuing. Remove all

self-adhesive pads from the underside of the switch, if they have been attached.

CAUTION: When mounting multiple switches into a rack, mount the switches

from the bottom up.

1

Place the supplied rack-mounting bracket on one side of the switch,

ensuring that the mounting holes on the switch line up to the mounting

holes in the rack-mounting bracket. Figure 1-6 illustrates where to mount

the brackets.

Figure 1-6. Attaching the Brackets

14 Getting Started Guide

2

Insert the supplied bolts into the rack-mounting holes and tighten with a

screwdriver.

3

Repeat the process for the rack-mounting bracket on the other side of the

switch.

4

Insert the switch into the 48.26 cm (19 inch) rack, ensuring that the rack-

mounting holes on the bracket line up with the mounting holes in the

rack.

5

Secure the bracket to the rack with either the rack bolts or cage nuts and

cage-nut bolts with washers (depending on the kind of rack you have).

Fasten the bolts on the bottom before fastening the bolts on the top.

CAUTION: Make sure that the supplied rack bolts fit the pre-threaded holes in the

rack.

NOTE: Make sure that the ventilation holes are not obstructed.

Installing as a Free-standing Switch

NOTE: Dell strongly recommends mounting the switch in a rack.

Install the switch on a flat surface if you are not installing it in a rack. The

surface must be able to support the weight of the switch and the switch

cables. The switch is supplied with four self-adhesive rubber pads.

1

Attach the self-adhesive rubber pads on each location marked on the

bottom of the switch.

2

Set the switch on a flat surface, and make sure that it has proper

ventilation by leaving 5 cm (2 inches) on each side and 13 cm (5 inches) at

the back.

Stacking Multiple N1124T-ON/N1124P-ON/

N1148T-ON/ N1148P-ON Switches

You can stack N1124T-ON/N1124P-ON/N1148T-ON/ N1148P-ON switches

up to four switches high using 10G SFP+ ports on the front of the switch.

The ports must be configured to support stacking. When multiple switches

are connected together through the stack ports, they operate as a single unit

with up to 208 front-panel ports. The stack operates and is managed as a

single entity. Refer to the User Configuration Guide and the CLI Reference

Guide for more information.

Getting Started Guide 15

Starting and Configuring the

N1100-ON Series Switch

The following flow chart provides an overview of the steps you use to perform

the initial configuration after the switch is unpacked and mounted.

Figure 1-7. Installation and Configuration Flow Chart

16 Getting Started Guide

Connecting an N1100-ON Series Switch to a

Terminal

After completing all external connections, configure the switch by connecting

it to a terminal.

NOTE: Read the Release Notes for this product before proceeding. You can

download the Release Notes from the Dell Support website at dell.com/support.

NOTE: Dell recommends that you obtain the most recent version of the user

documentation from the Dell Support website at dell.com/support.

To monitor and configure the switch via the USB console, use the console

port on the front panel of the switch to connect it to a computer running

VT100 terminal emulation software using the supplied USB cable. It may be

necessary to download and install a driver on first use of the USB cable.

The following equipment is required to use the console port:

• VT100-compatible computer with a USB port running VT100 terminal

emulation software,

such as HyperTerminal

®

and a USB driver.

• The supplied USB cable with a type B USB connector for the console port

and USB connector for the host PC.

Perform the following tasks to connect a terminal to the switch console port:

1

Connect the USB type B connector on the supplied switch and connect

the other end to a computer running VT100 terminal emulation software.

2

Configure the terminal emulation software as follows:

a

Select the appropriate serial port (for example, COM 1) to connect to

the console.

b

Set the data rate to 115,200 baud.

c

Set the data format to 8 data bits, 1 stop bit, and no parity.

d

Set the flow control to none.

e

Set the terminal emulation mode to

VT100

.

f

Select Terminal keys for Function, Arrow, and Ctrl keys. Make sure

that the setting is for Terminal keys (not Microsoft Windows keys).

3

Connect the USB type B connector on the cable directly to the switch

console port. The Dell Networking console port is located on the right side

of the front panel and is labeled with a

|O|O|

symbol.

Getting Started Guide 17

NOTE: Console access to the stack manager is available from any console

port via the local CLI. Only one USB console session at a time is supported.

Connecting an N1100-ON Series Switch to a

Power Source

CAUTION: Read the safety information in the

Safety and Regulatory Information

manual as well as the safety information for other switches that connect to or

support the switch.

The N1108T-ON and N1108P-ON models have one internal power supply.

The

power receptacle is on the rear panel. N1108EP-ON uses an external DC

power adaptor. The external DC power adaptor

AC and DC Power Connection

1

Make sure that the switch console port is connected to a PC running a

VT100 terminal emulator via the USB to USB Type B cable.

2

Using a 5-foot (1.5 m) standard power cable with safety ground connected,

connect the power cable to the AC main receptacle located on the rear

panel.

The PoE model switches have a heavy-duty power cable with a notched

connector for the switch power receptacle. Use of this type of cable is

mandatory for PoE-capable switches.

3

Connect the power cable to a grounded AC outlet.

18 Getting Started Guide

Booting the N1100-ON Series Switch

When the power is turned on with the local terminal already connected, the

switch goes through a power-on self-test (POST). POST runs every time the

switch is initialized and checks hardware components to determine if the

switch is fully operational before completely booting. If POST detects a

critical problem, the program flow stops. If POST passes successfully, valid

firmware is loaded into RAM. POST messages are displayed on the terminal

and indicate test success or failure. The boot process runs for approximately

60 seconds.

You can invoke the Boot menu after the first part of the POST is completed.

From the Boot menu, you can perform configuration tasks such as resetting

the system to factory defaults, activating the backup image, or recovering a

password. For more information about the Boot menu functions, refer to the

CLI Reference Guide.

Getting Started Guide 19

Performing the N1100-ON Series Initial

Configuration

The initial configuration procedure is based on the following assumptions:

• The Dell Networking switch was never configured before.

• The Dell Networking switch booted successfully.

• The console connection was established, and the

Dell Easy Setup Wizard

prompt appears on the screen of a PC running terminal emulation

software.

The initial switch configuration is performed through the console port. After

the initial configuration, you can manage the switch from the already-

connected console port or remotely through an interface defined during the

initial configuration.

NOTE: The switch is not configured with a default user name, password, or IP

address.

Before setting up the initial configuration of the switch, obtain the following

information from your network administrator:

• The IP address to be assigned to the management interface.

• The IP subnet mask for the network.

• The IP address of the management interface default gateway.

These settings are necessary to allow the remote management of the switch

through Telnet (Telnet client) or HTTP (Web browser).

Enabling Remote Management

On the N1100-ON Series switches, you can use any of the switch ports on the

front panel for in-band management. By default, all in-band ports are

members of VLAN 1.

The Dell Easy Setup Wizard includes prompts to configure network

information for the VLAN 1 interface on the N1100-ON Series switches. You

can assign a static IP address and subnet mask or enable DHCP and allow a

network DHCP server to assign the information.

Refer to the CLI Reference Guide for commands to configure network

information.

ページが読み込まれています...

Dell PowerSwitch N1100-ON Series クイックスタートガイド

Dell PowerSwitch N1100-ON Series クイックスタートガイド

他の言語で

関連論文

その他のドキュメント