Denon DN-S3500 ユーザーマニュアル

SERVICE MANUAL

TABLE TOP SINGLE CD PLAYER

MODEL DN-S3500

TOKYO, JAPAN

Denon Brand Company, D&M Holdings Inc.

X0252V.01 DE/CDM 0508

Some illustrations using in this service manual are

slightly different from the actual set.

Please use this service manual with referring to the

operating instructions without fail.

For purposes of improvement, specifications and

design are subject to change without notice.

For U.S.A., Canada, Europe, U.K.,

Asia, China, Taiwan R.O.C., Korea

& Japan model

Ver. 1

ページが読み込まれています...

8

DN-S3500

CONFIRMING THE SERVO

What is Service Program

Service program is a special program intended for confirming servo functions etc.

Required Measuring Implement

Reference disc (TCD784 or CO-74176)

1. Contents of Service Program

Turn on the power while pressing both B button and the PARAMETER knob to set the service mode of DN-S3500. The various

check items can be selected with the PARAMETER knob, the various test items can be selected with the A, SAMP, EXIT/RELOOP,

(SAMP.)EXIT/RELOOP, and BEND buttons. Press either the PARAMETER knob or PLAY/PAUSE button to start the check

or test and display the result.

To eject the disc, press the DISC EJECT button.

To cancel the service mode, turn the power off.

Process No.

(TRACK

Indication)

Function

(Character-display)

Contents

PARAMETER

knob

01

µcom Version check

(Version No.)

A PARAMETER knob is pushed and a version is checked.

1. System µcom version No. : "System_XXXX"

2. DSP soft version No. : "Dsp_XXXX"

02

"TR_Signal"

"HF_Signal"

Press the PARAMETER knob to turn the tracking servo off.

When the tracking servo is off, press the PARAMETER knob to turn the tracking

servo on.

03

Automatic Servo

Adjustment call

(Servo Data)

Press the PARAMETER knob to start automatic servo adjustment. When the

adjustment is completed, the adjustment data is displayed. The data can be

selected by turning the EFFECTS knob.

1. Disc check, CD/CD-RW

2. Focus gain data

3. Focus balance data

4. Focus offset data

5. Tracking gain data

6. Tracking balance data

7. Tracking offset data

8. S curve maximum

9. S curve minimum

04 "Fo_Gain"

Select the focus gain. Default : 7. Select the data with the scratch disc, then press

the PARAMETER knob to enter it. The higher the value, the higher the gain, while

the lower the value, the lower the gain.

* Do not change this without instruction from engineering.

05 "Tr_Gain" Select the tracking gain. Default : 2. The operation is the same as for the Fo Gain.

06 "Block_Err" The block error rate is displayed.

07 "PU._Clean"

When the PARAMETER knob is pressed, the pickup moves towards the outer

edge of the disc. The pickup lens becomes visible through the slit in the CD mech-

anism plate. The lens can be cleaned using a cotton swab, etc.

(Perform this operation with the top panel/cover removed and the disc ejected.)

08

Error Code Check

(Error Data)

During normal operation, the error code for the error that occurred is displayed.

Turn the EFFECTS knob to select up to 10 sets of error data stored in the mem-

ory. (See the error code table for a description of the error codes.)

Press the PARAMETER knob to set the error data clear mode. ("Error Clear?" is

displayed.) Press the PARAMETER knob again to clear all the error data.

09

Total Running Time

(Total Time)

The total operating time of the spindle motor is displayed. A total of 65,535 hours

can be counted, in units of hours.

NOTE: If the power is turned off after 59 minutes or less, that hour is not counted.

Press the PARAMETER knob to set the total time clear mode. ("Time Clear?" is

displayed.) Press the PARAMETER knob again to clear the total time.

9

DN-S3500

BEND+ button FLT all light check performed while button pressed.

BEND

-

button FLT all off check performed while button pressed.

button Disc eject status set while button pressed.

The disc loading/eject roller turns. The dirt can be cleaned off the roller by gently pressing a cotton swab with

"Iso-

propyl alcohol"

, against the roller.

(Perform this operation with the top panel/cover removed and the disc ejected.)

Servo automatic adjustment read-out value

2. TEST MODE

3. Error Code Table (Appears only at Heat Run and Chucking Test function)

Adjustment Item Adjustment Value indication at character portions.

1 Focus Gain 0408 ~ 3248

2 Focus Balance -50 ~ +50

3 Focus Offset -005 ~ +005

4 Tracking Gain 0392 ~ 1569

5 Tracking Balance -025 ~ +025

6 Tracking Offset -005 ~ +005

Function

(Character-display)

Contents

A button

Heat Run Test

H/R1 Normal

Press button A1, then press the PLAY/PAUSE button to start the test.

The disc is ejected, loaded and played repeatedly.

For discs containing 20 tracks or less, all the tracks are played.

For discs containing 21 tracks or more, only the first and last tracks on the disc are played.

If an error occurs, the error code is displayed and the stop mode is set.

A2 button

Chucking Test

H/R2 Tray

Press button A2, then press the PLAY/PAUSE button to start the test.

The disc load/eject, servo input and TOC reading operations are performed repeatedly.

If an error occurs, the error code is displayed and the stop mode is set.

SAMP button

Platter rotation speed

check

Press button SAMP, then press the PLAY/PAUSE button. The platter starts to rotate and

revolution number is displayed.

(SAMP.)EXIT

/RELOOP

button

Platter rotation speed

fine adjustment

Press the (SAMP.)EXIT/RELOOP button, then press the PLAY/PAUSE button. The Platter starts

to rotate and revolution number is displayed. The rotation speed can be adjusted to turn the

parameter knob.

EXIT/

RELOOP

button

System check

Sys. Check

Press button EXIT/RELOOP, then press the PLAY/PAUSE button to start the system check.

Once the check is completed, the results are displayed.

1. The system µcom and DSP communications are checked.

2. Reading and writing SDRAM of DSP are checked.

3. Reading and writing SDRAM of servo DSP are checked.

4. Communications between the system µcom and servo DSP are checked.

5. The CD drive operation is checked. (Inner edge switch detection is performed.)

6. The CD drive operation is checked. (Disc detection is performed.)

Once all the checks are completed, the results are displayed on the character display. The

numbers of the checks in items 1 to 6 above that were OK are displayed. If one of the checks

was not OK, the number of that item is not displayed.

Error Code Contents

E1 00

E1 01

E1 03

E1 04

E1 05

E1 06

Automatic Adjustment Error

Unable to detect disk

Unable to adjust tracking offset

Unable to adjust focus fine gain

Unable to actuate focus

Unable to actuate tracking

Unable to adjust tracking fine gain

E2 02 Servo down during automatic Adjustment

E3 00 Unable to read TOC

10

DN-S3500

4. µcom update

The system µcom and DSP can be updated from a disc.

The µcom should be updated to the latest version, when GU-3689(MAIN PWB UNIT) or IC102(Flash ROM) is replaced.

(1) Creating the update disc

Use the procedure described below to create the disc for updating the system microprocessor and DSP.

Store the update file on a CD-R or CD-RW disc in ISO9660 Mode 1 format, then finalize the disc.

Write the distributed update files using the "DISC AT ONCE" CD writing software and finalize.

Do not record any other software or data on the disc containing the update software.

Do not change the file names - use the file names as distributed.

(2) Updating the system µcom and DSP

Turn on the power and load the disc created in (1) above.

When the update disc is detected, "Version Up" is displayed. And "xxxx yyyyy" and "Push Play!" are displayed by turns.

xxxx : Old Version No., yyyy : New Version No.

Press the PLAY/PAUSE button. "NowLoading" is displayed and the updating procedure starts.

As updating proceeds, the playback position indicator lights in order from left to right.

NOTE: In some extremely rare cases, the updating procedure is not completed. If the updating procedure has not finished after

three minutes, there could be a problem. Turn off the power and repeat the operation from step (2) .

Depending on the problem that occurred, it may happen that no other operations can be performed. If this happens, GU-

3689 IC102 must be replaced. Software must be pre-recorded on the IC102. (When ordering the IC102, order the more

recent system microprocessor version number (GEN number).)

When updating is completed, "Complete!" is displayed and the disc is ejected.

ADJUSTMENT

When the motor (FG-3500) is replaced, platter rotation speed adjustment is necessary.

(1) Start the Platter Rotation Speed Fine Adjust mode in the test mode. (Refer to page 9)

The actual revolution number is indicated on the lower part of the Character display. (Standard is 33rpm)

The difference from the standard revolution number is indicated on the upper part of the Character display.

(2) Turn the parameter knob. And the "D_**"(left side) of the lower part of the Character display is set to "D_77".

Then check the difference from the standard revolution number.

a) The difference from the standard number is

-

5% ~ +1% :

Turn the parameter knob to set "

-

2%". And push the parameter knob to complete the adjustment.

b) The difference from the standard number is outside of

-

5% ~ +1% :

Start the platter revolution check mode in the test mode. (Refer to page 9)

Present revolution number is indicated on the lower part of character display. (Standard is 33rpm)

Difference from the standard revolution number is indicated on the upper part of character display.

Make adjustment by turning VR701 on the power unit GU-3690 so that difference from the standard revolution number

indicated on the upper part of character display becomes

-

2%.

E4 00

E4 01

Unable to close the disc holder in the regular time

Unable to open the disc holder in the regular time

E5 00

E5 01

E5 02

The inner SW dose not turn on

Slider error

The inner SW dose not turn off

E8 00 Track jumping was happened during memory of data. And unable to memorize data continuously.

Error Indication

TR MIN SEC FRAM CHARACTER

displays the track No. in

which error occurred.

Displays the time at which error occurred.

H Operation count

E Error code

Error Code Contents

ページが読み込まれています...

32

DN-S3500

NOTE FOR PARTS LIST

• Part indicated with the mark "nsp" are not always in stock and possibly to

take a long period of time for supplying, or in some case supplying of part

may be refused.

• When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-

supplying.

• Ordering part without stating its part number can not be supplied.

• Part indicated with the mark " " is not illustrated in the exploded view.

• Not including Carbon Film Resister ±5%, 1/4W Type in the P.W.Board

parts list. (Refer to the Schematic Diagram for those parts.)

• Not including Carbon Chip Resister 1/16W Type in the P.W.Board parts

list. (Refer to the Schematic Diagram for those parts.)

WARNING:

Parts marked with this symbol ! have critical characteristics.

Use ONLY replacement parts recommended by the manufacturer.

s

RD : 2B : 1/8 W F : ±1% P :

RC : 2E : 1/4 W G : ±2% NL :

RS : 2H : 1/2 W J : ±5% NB :

RW : 3A : 1 W K : ±10% FR :

RN : 3D : 2 W M : ±20% F :

RK : 3F : 3 W

3H : 5 W

RN 14K 2E 182 G FR

∗

18 2

Ö

1800

=1.8k

0

2

1R 2

Ö

1.2

1

2 R

CE 04W 1H 2R2 M BP

CE : 0J : 6.3 V F : ±1% HS :

CA : 1A : 10 V G : ±2% BP :

CS : 1C : 16 V J : ±5% HR :

CQ : 1E : 25 V K : ±10% DL :

CK : 1V : 35 V M : ±20% HF :

CC : 1H : 50 V Z : +80% U : UL

CP : 2A : 100 V −20% C : CSA

CM : 2B : 125 V P : +100% W : UL-CSA

CF : 2C : 160 V − 0% F :

CH : 2D : 200 V C : ±0.25pF

2E : 250 V D : ±0.5pF

2H : 500 V = :

2J : 630 V

∗

22 2

Ö

2200

µ

F

0

2

µ

F

22 2

Ö

2200pF=0.0022

µ

F

0

2

p

F

p

F

22 1

Ö

220pF

2

(0 2 )

0

(0 0 1 )

2R 2

Ö

2.2

µ

F

1

2 R

µ

F

AC

RD : Carbon 2B : 1/8W F : ±1% P : Pulse-resistant type

RC : Composition 2E : 1/4W G : ±2% NL : Low noise type

RS : Metal oxide film 2H : 1/2W J : ±5% NB : Non-burning type

RW : Winding 3A : 1W K : ±10% FR : Fuse-resistor

RN : Metal film 3D : 2W M : ±20% F : Lead wire forming

RK : Metal mixture 3F : 3W

3H : 5W

CE : Aluminum foil 0J : 6.3V F : ±1% HS : High stability type

electrolytic

CA : Aluminum solid 1A : 10V G : ±2% BP : Non-polar type

electrolytic

CS : Tantalum electrolytic 1C : 16V J : ±5% HR : Ripple-resistant type

CQ : Film 1E : 25V K : ±10% DL : For change and discharge

CK : Ceramic 1V : 35V M : ±20% HF : For assuring high

requency

CC : Ceramic 1H : 50V Z : +80% U : UL part

CP : Oil 2A : 100V –20% C : CSA part

CM : Mica 2B : 125V P : +100% W : UL-CSA type

CF : Metallized 2C : 160V –0% F : Lead wire forming

CH : Metallized 2D : 200V C : ±0.25pF

2E : 250V D : ±0.5pF

2H : 500V = : Others

2J : 630V

ll

l

Resistors

Ex.: RN 14K 2E 182 G FR

Type Shape Power Resist- Allowable Others

and per- ance error

formance

] Resistance

1 8 2 ⇒ 1800 ohm = 1.8 kohm

Indicates number of zeros after effective number.

2-digit effective number.

• Units: ohm

1 R 2 ⇒ 1.2 ohm

1-digit effective number.

2-digit effective number, decimal point indicated by R.

• Units: ohm

ll

l Capacitors

Ex.: CE 04W 1H 2R2 M BP

Type Shape Dielectric Capacity Allowable Others

and per- strength error

formance

] Capacity (electrolyte only)

2 2 2 ⇒ 2200µF

Indicates number of zeros after effective number.

2-digit effective number.

• Units: µF.

2 R 2 ⇒ 2.2µF

1-digit effective number.

2-digit effective number, decimal point indicated by R.

• Units: µF.

] Capacity (except electrolyte)

2 2 2 ⇒ 2200pF=0.0022µF

(More than 2) Indicates number of zeros after effective number.

2-digit effective number.

• Units: pF.

2 2 1 ⇒ 220pF

(0 or 1) Indicates number of zeros after effective number.

2-digit effective number.

• Units: pF.

• When the dielectric strength is indicated in AC, "AC" is included after the dieelectric

strength value.

ページが読み込まれています...

43

DN-S3500

EXPLODED VIEW

B

A

B

E

D

C

48

49

50

44

44A

45

68

46

47

68

74

67

37

38

41

62

43

36

42

62

36

62

34

35

36

32

33

71

26

29

30

3-5

61

23

71

69

9

2

8

3-3

66

69

71

21

24

3-6

31

23

27

3-1

66

3-2

66

28

22

25

66

3-4

71

39

7

69

6

69

63

69

64

4

6

7

69

70

20

7

69

6

69

7

69

10

11

5

40

73

12

72

69

66

65

19

1

18

60

63

17

13

14

15

16

64

E

F

A

Parts marked with this symbol have critical

characteristics.

Use ONLY replacement parts recommended by

the manufacturer.

WARNING:

ページが読み込まれています...

48

DN-S3500

NOTE FOR SCHEMATIC DIAGRAM

WARNING:

Parts marked with this symbol ! have critical characteristics.

Use ONLY replacement parts recommended by the manufactur-

er.

CAUTION:

Before returning the unit to the customer, make sure you make

either (1) a leakage current check or (2) a line to chassis resis-

tance check. If the leakage current exceeds 0.5 milliamps, or if

the resistance from chassis to either side of the power cord is

less than 460 kohms, the unit is defective.

WARNING:

DO NOT return the unit to the customer until the problem is lo-

cated and corrected.

NOTICE:

ALL RESISTANCE VALUES IN OHM. k=1,000 OHM

M=1,000,000 OHM

ALL CAPACITANCE VALUES IN MICRO FARAD.

P=MICRO-MICRO FARAD

EACH VOLTAGE AND CURRENT ARE MEASURED AT

NO SIGNAL INPUT CONDITION.

CIRCUIT AND PARTS ARE SUBJECT TO CHANGE

WITHOUT PRIOR NOTICE.

µ

ページが読み込まれています...

Denon DN-S3500 ユーザーマニュアル

Denon DN-S3500 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント