12
3 4
3
8
BDCDS12
2
3
3
7
4
6
C
2 8
E
B
45
A
1
D
2
ENGLISH
(Original instructions)
3
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER BDCDS12 sander has been designed
for sanding wood, metal, plastics and painted surfaces. This
tool is intended for consumer use only.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of fl ammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodifi ed plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the infl uence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your fi nger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
3
ENGLISH
2
3
3
7
4
6
C
2 8
E
B
45
A
1
D
2
ENGLISH
(Original instructions)
3
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER BDCDS12 sander has been designed
for sanding wood, metal, plastics and painted surfaces. This
tool is intended for consumer use only.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of fl ammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodifi ed plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the infl uence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your fi nger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
4
ENGLISH
4
ENGLISH
(Original instructions)
5
ENGLISH
(Original instructions)
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease.
Slippery handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situasions.
5. Battery tool use and care
a. Recharge only with the charger specifi ed by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fi re when used with
another battery pack.
b. Use power tools only with specifi cally designated
battery packs. Use of any other battery packs may create
a risk of injury and fi re.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fi re.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, fl ush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e. Maintain powertools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
6. service
a. Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings for sanders
@
Warning! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystand-
ers. Wear a dust mask specifi cally designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
u Hold power tool by insulated gripping surfaces when
performing an operation where the sanding accessory
may contact hidden wiring. Accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
@
Warning! Take special care when sanding some
woods (e.g. beech, oak) and metal which may
produce toxic dust. Wear a dust mask specifi -
cally designed for protection against toxic dust
and fumes and ensure that persons within or
entering the work area are also protected.
@
Warning! Use this tool in a well ventilated area
when sanding ferrous metals. Do not operate
the tool near fl ammable liquids, gases or dust.
Sparks or hot particles from sanding or arcing
motor brushes may ignite combustible materials.
@
Warning! Do not sand magnesium! There is a
risk of fi re or explosions.
u Thoroughly remove all dust after sanding.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
4
ENGLISH
(Original instructions)
5
ENGLISH
(Original instructions)
Safety when sanding paint
@
Warning! Observe the applicable regulations
for sanding paint. Pay special attention to the
following:
u Whenever possible, use a vacuum extractor for dust col-
lection.
u Take special care when sanding paint which is possibly
lead based and may produce toxic dust:
u Do not let children or pregnant women enter the work
area.
u All persons entering the work area should wear a mask
specially designed for protection against lead paint dust
and fumes.
u Do not eat, drink or smoke in the work area.
u Dispose of dust particles and any other removal debris
safely.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Additional safety instructions for batteries
Batteries (not supplied)
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
$
The tool is intend of indoor use only.
Labels on tool
The following pictograms along with the date code are shown
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear a dust mask.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust extraction
3. Sanding base
4. Battery
Charging the battery (Not supplied) (fi g. A)
The battery needs to be charged before fi rst use and
whenever it fails to produce suffi cient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u To charge the battery, insert the USB charger (5) into the
Battery.
u Plug the charger into a suitable power source and switch
on.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
5
ENGLISH
4
ENGLISH
(Original instructions)
5
ENGLISH
(Original instructions)
these instructions to operate the power tool.
Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease.
Slippery handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situasions.
5. Battery tool use and care
a. Recharge only with the charger specifi ed by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fi re when used with
another battery pack.
b. Use power tools only with specifi cally designated
battery packs. Use of any other battery packs may create
a risk of injury and fi re.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fi re.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, fl ush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e. Maintain powertools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
6. service
a. Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings for sanders
@
Warning! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystand-
ers. Wear a dust mask specifi cally designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
u Hold power tool by insulated gripping surfaces when
performing an operation where the sanding accessory
may contact hidden wiring. Accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
@
Warning! Take special care when sanding some
woods (e.g. beech, oak) and metal which may
produce toxic dust. Wear a dust mask specifi -
cally designed for protection against toxic dust
and fumes and ensure that persons within or
entering the work area are also protected.
@
Warning! Use this tool in a well ventilated area
when sanding ferrous metals. Do not operate
the tool near fl ammable liquids, gases or dust.
Sparks or hot particles from sanding or arcing
motor brushes may ignite combustible materials.
@
Warning! Do not sand magnesium! There is a
risk of fi re or explosions.
u Thoroughly remove all dust after sanding.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
4
ENGLISH
(Original instructions)
5
ENGLISH
(Original instructions)
Safety when sanding paint
@
Warning! Observe the applicable regulations
for sanding paint. Pay special attention to the
following:
u Whenever possible, use a vacuum extractor for dust col-
lection.
u Take special care when sanding paint which is possibly
lead based and may produce toxic dust:
u Do not let children or pregnant women enter the work
area.
u All persons entering the work area should wear a mask
specially designed for protection against lead paint dust
and fumes.
u Do not eat, drink or smoke in the work area.
u Dispose of dust particles and any other removal debris
safely.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Additional safety instructions for batteries
Batteries (not supplied)
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
$
The tool is intend of indoor use only.
Labels on tool
The following pictograms along with the date code are shown
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear a dust mask.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust extraction
3. Sanding base
4. Battery
Charging the battery (Not supplied) (fi g. A)
The battery needs to be charged before fi rst use and
whenever it fails to produce suffi cient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u To charge the battery, insert the USB charger (5) into the
Battery.
u Plug the charger into a suitable power source and switch
on.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
6
ENGLISH
6
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
Fitting and removing the battery (Not supplied)
(fi g. B)
u To fi t the battery, line it up with the receptacle on the tool.
Slide the battery into the receptacle and push up until the
battery snaps into place.
u To remove the battery, push the release button (5) while at
the same time pulling the battery out of the receptacle.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the battery is removed.
Fitting sanding sheets (Fig. C )
u Attach a sanding sheet (7) by pressing the 'hooked' velcro
side to the 'looped' velcro underside of the sanding base
(3).
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
u To switch the tool on, depress the on/off switch (1) at the
position I.
u To switch the tool off, depress the on/off switch (1) at the
position O.
Technical data
BDCDS12
Input voltage
V
dc
12
No - load speed
min
-1
11000 OPM
Oscilating angle
°
2.8
Sanding base surface
mm
2
5078
Weight
kg
0.63 (with battery 0.88)
Battery (not supplied)
BDCB12
Voltage V
dc
12
Capacity Ah 1.5
Type Lithium-Ion
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.Your charger does not require any
maintenance apart from regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used
again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with effi cient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location near-
est to you.
NOTE
u Black & Decker's policy is one of continuous improve-
ment to our products and, as such, we reserve the right to
change product specifi cations without prior notice.
u Standard equipment and accessories may vary by country.
u Product specifi cations may differ by country.
u Complete product range may not be available in all
countries.
Contact your local Black & Decker dealers for range
availability.
Batteries
Z
There are no user servicable parts inside.
6
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
u At the end of your products life return the whole unit
to your service agent or to a local recycling station to
have the battery recycled. Do not throw the unit out with
household waste.
7
ENGLISH
6
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
Fitting and removing the battery (Not supplied)
(fi g. B)
u To fi t the battery, line it up with the receptacle on the tool.
Slide the battery into the receptacle and push up until the
battery snaps into place.
u To remove the battery, push the release button (5) while at
the same time pulling the battery out of the receptacle.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the battery is removed.
Fitting sanding sheets (Fig. C )
u Attach a sanding sheet (7) by pressing the 'hooked' velcro
side to the 'looped' velcro underside of the sanding base
(3).
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
u To switch the tool on, depress the on/off switch (1) at the
position I.
u To switch the tool off, depress the on/off switch (1) at the
position O.
Technical data
BDCDS12
Input voltage
V
dc
12
No - load speed
min
-1
11000 OPM
Oscilating angle
°
2.8
Sanding base surface
mm
2
5078
Weight
kg
0.63 (with battery 0.88)
Battery (not supplied)
BDCB12
Voltage V
dc
12
Capacity Ah 1.5
Type Lithium-Ion
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.Your charger does not require any
maintenance apart from regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used
again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with effi cient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location near-
est to you.
NOTE
u Black & Decker's policy is one of continuous improve-
ment to our products and, as such, we reserve the right to
change product specifi cations without prior notice.
u Standard equipment and accessories may vary by country.
u Product specifi cations may differ by country.
u Complete product range may not be available in all
countries.
Contact your local Black & Decker dealers for range
availability.
Batteries
Z
There are no user servicable parts inside.
6
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
u At the end of your products life return the whole unit
to your service agent or to a local recycling station to
have the battery recycled. Do not throw the unit out with
household waste.
8
繁中
繁體中
繁中
請注意
！ /
Warning
！
Attachments and accessories are not the
same in each region
,
please only refer to Taiwan
Traditional Chinese description in this manual.
設計用途
BLACK+DECKER BDCDS12
DIY
安全說明
電動工具一般安全警告
@
警 告！ 請閱讀所有安全警告及指示。
/
請妥善保存所有的警告與指示以備將來查閱。
1. 工作場地安全
a. 保持工作場地清潔明亮。
b. 請勿在易爆環境，如有易燃液體、氣體或粉塵的
環境中操作電動工具。
c. 請等待兒童和旁觀者離開之後才操縱電動工具。
2. 電氣安全
a. 電動工具插頭必須與插座相符。切勿以任何方式
改裝插頭。需接地的電動工具不能使用任何配接
器插頭。
b. 避免人體接觸接地表面，如管道、散熱片、爐灶
和冰箱。
c. 請勿將電動工具暴露在雨中或潮濕環境中。
d. 切勿濫用電線。請勿使用電線來搬運、拉動電動
工具或拔出插頭。讓電線遠離熱、油、銳邊和活
動部件。
e. 若要在戶外使用電動工具，請使用適合戶外使用
的延長電纜。
f. 若必須在潮濕場合使用電動工具，請使用漏電保
護器（RCD）。 RCD
3. 人身安全
a. 保持警覺；在操作電動工具時，請留意所執行的
操作並按照一般的常識執行。請勿在疲倦，或受
到藥物、酒精或治療的影響下操作電動工具。
b. 使用個人防護裝置。始終佩戴護目裝備。
c. 避免意外啟動。連接電源及/或電池組、撿取或搬
運電動工具之前，請確定開關處於關閉位置。
d. 接通電動工具之前，請卸下所有的調整鑰匙或扳
手。
e. 不要過度伸張雙手。時刻注意腳下和身體的平
衡。
f. 適當穿著。請勿穿寬鬆衣服或佩戴飾品。讓您的
頭髮、衣服和手套遠離活動部件。
g. 若配備用於連接排屑裝置、集塵設備的裝置，請
確定正確連接和使用這些裝置。
h. 請勿因頻繁使用而對工具特別熟悉，讓你變得自
滿而忽略工具的安全原則。
4. 電動工具的使用與注意事項
a. 請勿超負荷使用電動工具。根據您的用途使用適當
的電動工具。
b. 若開關不能開啟或關閉電源，切勿使用該電動工
具。
c. 在執行任何調整、更換配件或儲存電動工具之
前，必須從電源上拔掉插頭及/或卸下電池組。
d. 請將閒置的電動工具儲存在兒童無法接觸的地
方，並且勿讓不熟悉電動工具或對這些說明不瞭
解的人員操作電動工具。
e. 維護電動工具。檢查活動部件是否對準或卡住、
是否存在任何破損情況，或任何能影響電動工具
運行的其他情況。若有損毀，必須在使用之前修
理電動工具。
f. 保持刀具鋒利和清潔。
9
繁體中
繁中
g. 遵循使用指示、特定類型電動工具的專用方式，
以及工作條件和所要執行的工作來使用電動工
具、配件和工具鑽頭等。
h. 把手和抓握表面都應保持乾燥、清潔及遠離油脂。
5. 電池工具的使用與注意事項
a. 只能使用製造商指定的充電器為電池充電。
b. 請使用原廠的電動工具電池組。
c. 不使用電池組時，請將其遠離如迴紋針、硬幣、
鑰匙、釘子、螺絲以及其他可連通電池兩極的金
屬物品。
d. 濫用電池的情況下，液體會從電池中噴出；
避免與液體接觸。若不小心接觸液體，請用清水
沖洗。若液體噴濺到眼睛上，沖洗之後還要進行
治療。
e. 維護工具與配件。檢查活動部件是否對準或卡
住、是否存在任何破損情況，或任何能影響電動
工具運行的其他情況。若有損毀，必須在使用之
前修理電動工具。
f. 保持刀具鋒利和清潔。
g. 遵循使用指示以及工作條件和所要執行的工作使
用電動工具、配件和工具刀頭等。
6. 維修
a. 電動工具之修理，僅可由認證的技術人員執行。
請勿交由非百得認證服務中心的技術人員進行修
理、維護、調整。若產品經由非百得認證的維修
工程師拆解、組裝、調整，恕無法適用百得一年
家用保修條款。為充份發揮其功能，修理、維
護、調整請務必使用原廠零件。
電動工具之附加安全警告
@
警告！
@
警告！
u
若在執行操作時磨砂配件可能會接觸隱藏的電
線，則從絕緣手柄表面握住電動工具。
u
使用夾具或採取其他可行的方法，將工件固定、
支撐到穩定的平台上。
@
警告！
@
警告！
@
警告！ 請勿對鎂進行磨砂！
u
u
/
産
磨砂油漆的安全注意事項
@
警告！
u
u
u
u
u
u
他人的安全
u
u
剩餘風險
10
u
/
u
u
u
u
MDF
電池之附加安全指示
電池（需另購）
u
u
u
40ºC
u
10 ºC 40 ºC
u
u
$
工具上的標籤
警告！
2016 23 BM
u
BLACK+DECKER
功能部件
1.
2.
3.
4.
4
ENGLISH
(Original instructions)
5
ENGLISH
(Original instructions)
Safety when sanding paint
@
Warning! Observe the applicable regulations
for sanding paint. Pay special attention to the
following:
u Whenever possible, use a vacuum extractor for dust col-
lection.
u Take special care when sanding paint which is possibly
lead based and may produce toxic dust:
u Do not let children or pregnant women enter the work
area.
u All persons entering the work area should wear a mask
specially designed for protection against lead paint dust
and fumes.
u Do not eat, drink or smoke in the work area.
u Dispose of dust particles and any other removal debris
safely.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Additional safety instructions for batteries
Batteries (not supplied)
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
$
The tool is intend of indoor use only.
Labels on tool
The following pictograms along with the date code are shown
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear a dust mask.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust extraction
3. Sanding base
4. Battery
Charging the battery (Not supplied) (g. A)
The battery needs to be charged before rst use and
whenever it fails to produce sufcient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u To charge the battery, insert the USB charger (5) into the
Battery.
u Plug the charger into a suitable power source and switch
on.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
為電池充電（需另購）（ 圖 A）
警 告！ 10ºC 40ºC
24ºC
注意：若電池溫度低於約 0ºC 或高於 40ºC，充電器
將不會為電池充電。
電池應留在充電器中，電池溫
度升高或降低後，充電器將自動開始充電。
u
USB 5
u
u
u
1 6
安裝及卸下電池（需另購）（ 圖 B）
u
u
5
裝配
警 告！
安裝砂紙（圖 C）
u
7
3
使用
警 告！
開啟與關閉
u
I 1
u
O
1
11
繁體中
繁中
技術資料
BDCDS12
標稱電壓
最大電壓
10.8 VDC
12 VDC
空載轉速 11000 OPM
震動角度
2.8
o
底盤尺寸
3.5" 5078 mm
2
砂紙固定方式
重量
0.63 kg 0.88 kg
維護
BLACK+DECKER
警 告！
u
u
u
保護環境
Black & Decker
z
服務資訊
Black & Decker
Black & Decker
Black & Decker
附註
u
Black & Decker
u
/
u
/
u
/
Black & Decker
電池
Z
u
/
33 2
02-2834-1741
N560811
10/2017
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
他の言語で
- English: Black & Decker BDCDS12B User manual
関連論文
-
BLACK+DECKER A71452 ユーザーマニュアル
-
BLACK+DECKER BDCS20 ユーザーマニュアル
-
-
BLACK+DECKER BDCJS12 ユーザーマニュアル
-
BLACK+DECKER BEW200 ユーザーマニュアル
-
BLACK+DECKER EPC12 ユーザーマニュアル
-
BLACK+DECKER KP600 ユーザーマニュアル
-
BLACK+DECKER KS600E ユーザーマニュアル
-
BLACK+DECKER BDCDD12 ユーザーマニュアル
-