Sony KD-85X9500B ユーザーマニュアル

ブランド: Sony

モデル: KD-85X9500B

カテゴリー: 液晶テレビ

タイプ: ユーザーマニュアル

KD-85X9500B

Television

Reference Guide

Table of Contents

Safety information . . . . . . . . . . . . . . . . . . . . . 2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Attaching the Table-Top Stand

(Alternative) . . . . . . . . . . . . . . . . . . . . . . . . 6

Preventing the TV from toppling over . . . . . 8

Hiding the camera . . . . . . . . . . . . . . . . . . . . . 8

Using the Remote Control . . . . . . . . . . . . . 8

Displaying the Touchpad Operation

Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Launching the Touchpad Tutorial . . . . . . . . .9

Connecting Other Devices. . . . . . . . . . . . . 9

Installing the TV to the Wall . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . 15

Troubles and Solutions . . . . . . . . . . . . . . . . 15

Specifications . . . . . . . . . . . . . . . . . . . . . . 16

Introduction

Thank you for choosing this Sony product.

Before operating the TV, please read this manual thoroughly and

retain it for future reference.

Note

• Before operating the TV, please read “Safety information”

(page 2).

• Instructions about “Installing the TV to the Wall” are included

within this TV’s instructions manual.

• Images and illustrations used in Quick Start Guide and this

manual are for reference only and may differ from actual

product appearance.

Location of the identification label

Labels for the TV Model No. and Power Supply rating are located

on the rear of the TV.

WARNING

Batteries must not be exposed to excessive heat such as

sunshine, fire or the like.

Installation/Set-up

Install and use the TV set in accordance with the instructions

below in order to avoid any risk of fire, electrical shock or damage

and/or injuries.

Installation

• To avoid slipping and causing personal injury, do not step on

the TV protection bag when unpacking the TV set.

• The TV set should be installed near an easily accessible AC

power outlet (mains socket).

• Place the TV set on a stable, level surface to avoid it from falling

down and cause personal injury or damage to the TV.

• Install the TV where it cannot be pulled, pushed, or knocked

over.

• Install the TV so that the TV's Table-Top Stand does not

protrudes out from the TV stand (not supplied).

If the Table-Top Stand protrudes out from the TV stand, it may

cause TV set to topple over, fall down, and cause personal injury

or damage to the TV.

• Only qualified service personnel should carry out wall

installations.

• For safety reasons, it is strongly recommended that you use

Sony accessories, including:

 Wall-Mount Bracket SU-WL500

• Be sure to use the screws supplied with the Wall-Mount Bracket

when attaching the Wall-Mount Bracket to the TV set. The

supplied screws are designed as indicated by illustration when

measured from the attaching surface of the Wall-Mount Bracket.

The diameter and length of the screws differ depending on the

Wall-Mount Bracket model.

This television is designed for use in Hong Kong and ensured

the usage in Hong Kong only.

Safety information

Use of screws other than those supplied may result in internal

damage to the TV set or cause it to fall, etc.

Transporting

• Before transporting the TV set, disconnect all cables.

• Four or more people are needed to transport a large TV set.

• When transporting the TV set by hand, hold it as shown below.

Do not put stress on the LCD panel and the frame around the

screen.

• When transporting the TV set, do not subject it to jolts or

excessive vibration.

• When transporting the TV set for repairs or when moving, pack

it using the original carton and packing material.

Topple prevention

• Be sure to use strong cord that is capable of supporting the

weight of the TV.

Ventilation

• Never cover the ventilation holes or insert anything in the

cabinet.

• Leave space around the TV set as shown below.

• It is strongly recommended that you use a Sony Wall-Mount

Bracket in order to provide adequate air-circulation.

Installed on the wall

Installed with stand

• To ensure proper ventilation and prevent the collection of dirt or

dust:

 Do not lay the TV set flat, install upside down, backwards, or

sideways.

 Do not place the TV set on a shelf, rug, bed or in a closet.

 Do not cover the TV set with a cloth, such as curtains, or items

such as newspapers, etc.

 Do not install the TV set as shown below.

AC power cord (mains lead)

Handle the AC power cord (mains lead) and outlet (mains socket)

as follows in order to avoid any risk of fire, electrical shock or

damage and/or injuries:

 Use only Sony supplied AC power cords (mains lead), not those

of other brands.

 Insert the plug fully into the AC power outlet (mains socket).

 Operate the TV set on a 220–240 V AC supply only.

 When wiring cables, be sure to unplug the AC power cord

(mains lead) for your safety and take care not to catch your feet

on the cables.

 Disconnect the AC power cord (mains lead) from the AC power

outlet (mains socket) before working on or moving the TV set.

 Keep the AC power cord (mains lead) away from heat sources.

 Unplug the AC power plug (mains plug) and clean it regularly. If

the plug is covered with dust and it picks up moisture, its

insulation may deteriorate, which could result in a fire.

Note

• Do not use the supplied AC power cord (mains lead) on any

other equipment.

• Do not pinch, bend, or twist the AC power cord (mains lead)

excessively. The core conductors may be exposed or broken.

• Do not modify the AC power cord (mains lead).

• Do not put anything heavy on the AC power cord (mains lead).

• Do not pull on the AC power cord (mains lead) itself when

disconnecting the AC power cord (mains lead).

• Do not connect too many appliances to the same AC power

outlet (mains socket).

• Do not use a poor fitting AC power outlet (mains socket).

Prohibited Usage

Do not install/use the TV set in locations, environments or

situations such as those listed below, or the TV set may

malfunction and cause a fire, electrical shock, damage and/or

injuries.

Location:

• Outdoors (in direct sunlight), at the seashore, on a ship or other

vessel, inside a vehicle, in medical institutions, unstable

locations, near water, rain, moisture or smoke.

• If the TV is placed in the changing room of

a public bath or hot spring, the TV may be

damaged by airborne sulfur, etc.

• For best picture quality, do not expose the screen to direct

illumination or sunlight.

• Avoid moving the TV from a cold area to a warm area. Sudden

room temperature changes may cause moisture condensation.

This may cause the TV to show poor picture and/or poor colour.

Should this occur, allow moisture to evaporate completely

before powering the TV on.

Screw (supplied with the

Wall-Mount Bracket)

Wall-Mount Bracket

8 mm - 12 mm

TV's rear cover

30 cm

10 cm

Leave at least this space around the set.

30 cm

10 cm

Leave at least this space around the set.

6 cm

Air circulation is blocked.

Wall Wall

Environment:

 Places that are hot, humid, or excessively dusty; where insects

may enter; where it might be exposed to mechanical vibration,

near flammable objects (candles, etc). The TV set shall not be

exposed to dripping or splashing and no objects filled with

liquids, such as vases, shall be placed on the TV.

 Do not place the TV in a humid or

dusty space, or in a room with oily

smoke or steam (near cooking tables

or humidifiers). Fire, electric shock, or

warping may result.

 Do not install the TV in places subject to extreme temperature,

such as in direct sunlight, near a radiator or a heating vent. The

TV may overheat in such conditions which can cause

deformation of the enclosure and/or TV malfunction.

Situation:

• Do not use when your hands are wet, with the cabinet removed,

or with attachments not recommended by the manufacturer.

Disconnect the TV set from AC power outlet (mains socket) and

antenna (aerial) during lightning storms.

• Do not install the TV so that it sticks out

into an open space. Injury or damage

from a person or object bumping into

the TV may result.

Broken pieces:

• Do not throw anything at the TV set. The screen glass may break

by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you have

unplugged the AC power cord (mains lead). Otherwise electric

shock may result.

When not in use

• If you will not be using the TV set for several days, the TV set

should be disconnected from the AC power (mains) for

environmental and safety reasons.

• As the TV set is not disconnected from the AC power (mains)

when the TV set is just turned off, pull the plug from the AC

power outlet (mains socket) to disconnect the TV set

completely.

• However, some TV sets may have features that require the TV

set to be left in standby to work correctly.

For children

• Do not allow children to climb on the TV set.

• Keep small accessories out of the reach of children, so that they

are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the AC power cord (mains lead)

immediately if any of the following problems occur.

Ask your dealer or Sony service centre to have it checked by

qualified service personnel.

When:

 AC power cord (mains lead) is damaged.

 Poor fitting of AC power outlet (mains socket).

 TV set is damaged by being dropped, hit or having something

thrown at it.

 Any liquid or solid object falls through openings in the cabinet.

About LCD Monitor Temperature

When the LCD Monitor is used for an extended period, the panel

surrounds become warm. You may feel hot when touching there

by the hand.

Viewing the TV

• Some people may experience discomfort (such as eye strain,

fatigue, or nausea) while watching 3D video images or playing

stereoscopic 3D games. Sony recommends that all viewers take

regular breaks while watching 3D video images or playing

stereoscopic 3D games. The length and frequency of necessary

breaks will vary from person to person. You must decide what

works best. If you experience any discomfort, you should stop

watching the 3D video images or playing stereoscopic 3D

games until the discomfort ends; consult a doctor if you believe

necessary. You should also review (i) the instruction manual of

any other device or media used with this television and (ii) our

website (http://www.sony-asia.com/support) for the latest

information. The vision of young children (especially those

under six years old) is still under development. Consult your

doctor (such as a pediatrician or eye doctor) before allowing

young children to watch 3D video images or play stereoscopic

3D games. Adults should supervise young children to ensure

they follow the recommendations listed above.

• Do not use, store, or leave the 3D Glasses or battery near a fire,

or in places with a high temperature, e.g., in direct sunlight, or

in sun-heated cars.

• When using the simulated 3D function, please note that the

displayed image is modified from the original due to the

conversion done by this television.

• View the TV in moderate light, as viewing the TV in poor light or

during long period of time, strains your eyes.

• When using headphones, adjust the volume so as to avoid

excessive levels, as hearing damage may result.

LCD Screen

• Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are effective, black

dots may appear or bright points of light (red, blue, or green)

may appear constantly on the LCD screen. This is a structural

property of the LCD screen and is not a malfunction.

• Do not push or scratch the front filter, or place objects on top of

this TV set. The image may be uneven or the LCD screen may be

damaged.

• If this TV set is used in a cold place, a smear may occur in the

picture or the picture may become dark. This does not indicate a

failure. These phenomena disappear as the temperature rises.

• Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this TV set is in use. This

is not a malfunction.

• The LCD screen contains a small amount of liquid crystal. Follow

your local ordinances and regulations for disposal.

Handling and cleaning the screen surface/

cabinet of the TV set

Be sure to unplug the AC power cord (mains lead) connected to

the TV set from AC power outlet (mains socket) before cleaning.

To avoid material degradation or screen coating degradation,

observe the following precautions.

• To remove dust from the screen surface/cabinet, wipe gently

with a soft cloth. If dust is persistent, wipe with a soft cloth

slightly moistened with a diluted mild detergent solution.

• Never spray water or detergent directly on

the TV set. It may drip to the bottom of the

screen or exterior parts and enter the TV set,

and may cause damage to the TV set.

• Never use any type of abrasive pad, alkaline/acid cleaner,

scouring powder, or volatile solvent, such as alcohol, benzene,

thinner or insecticide. Using such materials or maintaining

prolonged contact with rubber or vinyl materials may result in

damage to the screen surface and cabinet material.

• Periodic vacuuming of the ventilation openings is

recommended to ensure to proper ventilation.

• Do not handle the speakers with excessive force during cleaning

or maintenance to prevent any damages.

Precautions

Optional Equipment

Keep optional components or any equipment emitting

electromagnetic radiation away from the TV set. Otherwise

picture distortion and/or noisy sound may occur.

Wireless Function of the unit

• Do not operate this unit near medical equipment (pacemaker,

etc.), as malfunction of the medical equipment may result.

• Although this unit transmits/receives scrambled signals, be

careful of unauthorised interception. We cannot be responsible

for any trouble as a result.

Caution about handling the remote control

• Observe the correct polarity when inserting batteries.

• Do not use different types of batteries together or mix old and

new batteries.

• Dispose of batteries in an environmentally friendly way. Certain

regions may regulate the disposal of batteries. Please consult

your local authority.

• Handle the remote control with care. Do not drop or step on it,

or spill liquid of any kind onto it.

• Do not place the remote control in a location near a heat source,

a place subject to direct sunlight, or a damp room.

Attaching the Table-Top Stand

(Alternative)

You can change the Table-Top Stand from the

middle to the edge position by referring to the

instructions below.

Note

• Five or more people are needed to carry out this

installation.

• Ensure that there are no objects in front of the TV.

To bundle the cables

1 Attach the cable clampers.

Location of cable clamper when the Table-Top Stand

is attached to middle position.

Location of cable clamper for Table-Top Stand (edge

or middle position) and Floor Stand.

Edge position

Thick

cushion

1.5 N∙m

{15 kgf∙cm}

IR Sensor

3D Sync

Transmitter

Note

• Using the Port Replicator can simplify cable

management to a single cable connection to the TV.

• To detach the cable clamper from the TV, press the

top of the clamper 1, then pinch 2 as illustrated.

2 Bundle the AC power cord (mains lead)

with a cable holder, and connecting

cables with cable clampers.

3 Remove the stand cover.

4 Fix the cable to the stand with

attachments in order to avoid damage

to the cable.

5 Attach the stand cover.





If you do not wish to use the camera, hide it as

illustrated.

Note

• When using the camera, position it at the front top of

the TV.

Using the Remote Control

You can operate the TV by using the supplied

Touchpad Remote Control or IR (infrared)

Remote Control.

Note

• Touchpad Remote Control can only be used after

registration with the TV. You can register the

Touchpad Remote Control by pressing HOME, then

select [Settings] t

[System Settings] t

[Touchpad Remote Control Setup].

Touchpad Operation Guide allows you to see

the main gesture commands that are available

for the current TV screen.

1 Touch and keep your finger on the

centre of the touchpad to display the

Touchpad Operation Guide.

Preventing the TV from toppling over

Hiding the camera

8-12 mm

Displaying the Touchpad Operation

Guide

Touchpad

Remote Control

1 Press HOME.

2 Slide to select [Help], then press the

touchpad.

3 Slide up/down to select [Touchpad

Tutorial], then press the touchpad.

Follow the instructions on the screen.

Note

• You can also launch the Touchpad Tutorial by

pressing HOME, then select [Settings] t

[System Settings] t [Touchpad configurations] t

[Start Tutorial].

Connecting Other Devices

For more information on connections, refer to

the i-Manual.

Note

• For connection with Port Replicator, refer to the

installation guide supplied with the Port Replicator.

To connect with an HDMI cable

Note

• Connect 4K devices (4K Media Player, 4K Set Top Box,

etc.) to the HDMI IN 2 or HDMI IN 1 jack of the TV to

enjoy copyright protected content.

To connect with component cables

Launching the Touchpad Tutorial

To HDMI OUT

< 12 mm

< 21 mm

To AUDIO OUT To COMPONENT

OUT (P

R/PB/Y)

To connect with AV composite cables

To connect MHL Device

The TV simultaneously charges the MHL-

compatible connected device while playing

photo/music/video files. You can use the TV

remote control to control the connected MHL-

compatible device.

Note

• If [Auto Input Change (MHL)] is set to [On], the TV

automatically switches to HDMI IN 2/MHL or HDMI IN

4/MHL from other input when MHL-compatible

device is connected to HDMI IN 2/MHL or HDMI IN 4/

MHL jack. The availability of [Auto Input Change

(MHL)] depends on whether the MHL-compatible

device can support this feature.

• If [MHL Charging during Standby] is set to [On], you

can continue charging the MHL-compatible device

even when the TV is in standby mode.

• Connect the 4K smartphone or mobile devices to the

HDMI IN 2/MHL jack.

• Use authorized MHL 3 CABLE with MHL logo for 4K

smartphone or mobile devices.

To VIDEO OUT

Use authorized

MHL 3 CABLE

with MHL logo

(not supplied)

Use authorized

MHL 2 CABLE

with MHL logo

(not supplied)

MHL 3

device

MHL 2

device

SD 4K/HD

Picture Quality

• AV composite cable

• Antenna (aerial) cable

Standard definition (SD) videos have picture signals with a

vertical resolution of 480 (NTSC) or 576 (PAL/SECAM) lines.

• Component cable • HDMI cable

High definition (HD) videos have picture signals

with a vertical resolution of 720 or 1080 lines.

(For 4K vertical resolution: 2,160 lines)

Installing the TV to the Wall

This TV’s instruction manual only shows the steps on preparing the installation of the TV before

installing to the wall.

To Customer s:

For product protection and safety reasons, Sony strongly recommends that installation of your

TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.

To Sony Dealers and Contractors:

Provide full attention to safety during the installation, periodic maintenance and examination of

this product.

Use the Wall-Mount Bracket SU-WL500 (not supplied) to install the TV to the wall.

Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the installation.

Note

• Be sure to store the removed screws in a safe place, keeping them away from children.

1 Attach the Mounting Hook using the four screws supplied with the Wall-Mount Bracket.

Sufficient expertise is required for installing this product, especially to determine the strength of the wall for

withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers

or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for

any damage or injury caused by mishandling or improper installation.

Mounting Hook

Screw (+PSW 6 × 16)

2 Make sure that the wall has enough space for the TV and is capable of supporting a

weight of at least four times that of the TV. Refer to the following table on installing the TV

to the wall. See page 15-17 (Specifications) for the TV’s weight.

Unit: mm

* Only applicable for 0° for this TV model.

Note

• Figures in the table may differ slightly depending on the installation.

3 Connect necessary cables to the TV.

4 Detach the Table-Top Stand or Floor Stand from the TV.

Note

• When attaching the Table-Top Stand or Floor Stand again, be sure to fasten the screws (previously removed) to

the original holes on the rear of the TV.

Model Name

KD-

Display dimensions Screen centre dimension Length for mounting

Angle (0°)*

85X9500B 1,954 1,150 173 747 137

Screen centre point

5 Install the TV on the wall.

SU-WL500

Refer to the instructions supplied with the Wall-Mount Bracket for your model to install the TV on the wall.

Model Name

KD-

Screw location Hook location

85X9500B d, j a

Screw location

When installing the Mounting Hook on the TV.

Hook location

When installing the TV onto the Base Bracket.

Troubleshooting

When the illumination LED is flashing in red,

count how many times it flashes (interval

time is three seconds).

If the illumination LED flashes red, reset the TV

by disconnecting the mains lead from the TV for

two minutes, then turn on the TV.

If the problem persists, contact your dealer or

Sony service centre with the number of times

the Illumination LED flashes red (interval time is

three seconds). Press / on the TV to turn it

off, disconnect the mains lead, and inform your

dealer or Sony service centre.

When the illumination LED is not flashing,

check the items as follows.

You can also refer to [Troubleshooting] in the

i-Manual or perform self-diagnosis by selecting

[Help]  [Customer Support]  [Self

Diagnostics]. If the problem persists, have your

TV serviced by qualified service personnel.

Troubles and Solutions

There is no picture (screen is dark) and no

sound.

 Check the antenna (aerial)/cable connection.

 Connect the TV to the AC power (mains), and

press / on the TV or remote control.

Some programmes cannot be tuned.

 Check the antenna (aerial).

The remote control does not function.

 Replace the batteries.

 Your TV may be in SYNC mode.

Press Control Bar (….) and slide left/right to select

[SYNC MENU] then press the touchpad. Select [TV

Control] and then select [Home (Menu)] or

[Options] to control the TV.

When using IR Remote Control, press SYNC

MENU, select [TV Control] and then select [Home

(Menu)] or [Options] to control the TV.

The [Parental Lock] password has been

forgotten.

 Enter 9999 for the PIN code. (PIN code 9999 is

always accepted.)

The TV surrounds become warm.

 When the TV is used for an extended period, the

TV surrounds become warm.

You may feel hot when touching there by the

hand.

Frozen audio or video, a blank screen, or the

TV does not respond to TV or remote control

buttons.

 Perform a simple reset of the TV by unplugging

the AC power cord (mains lead) for two minutes,

then plug it in again.

The /, CH+/–,  +/–, ///, , and

HOME buttons cannot be located on the TV.

 See below illustration for location of the buttons

on the TV.

The illumination LED is turned on.

 If you do not wish to light up the illumination LED,

you can turn it off.

Press HOME, then select

[Settings] t

[System Settings] t [General Set-up] t

[Illumination LED] t [Off]. You can also press

OPTIONS, then select [Illumination LED] t [Off].

Cannot connect to a wireless router by WPS.

• If you use WEP security, select [Easy] t [Wi-Fi] t

[Connect by scan list]. Then, select the network

name (SSID) you want to connect.

Cannot find the required network name in

network setup.

• Select [[Manual Entry]] and press to enter

network name.

Rear of TV

Specifications

System

Panel system

LCD (Liquid Crystal Display) Panel, LED Backlight

TV system

Analogue: B/G, I, D/K, M, L

Digital: DTMB

Colour/video system

Analogue: PAL, SECAM, NTSC3.58, NTSC4.43

Digital: Refer to the i-Manual

Channel coverage

Analogue: UHF/VHF/Cable

Digital: UHF

Sound output

10 W + 10 W + 10 W + 10 W

Wireless technology

Protocol IEEE802.11a/b/g/n

Input/Output jacks

Antenna (aerial)/cable

75 ohm external terminal for VHF/UHF

/ VIDEO IN 1

Video/Audio input (phono jacks)

/ COMPONENT IN

YPBPR (Component Video): 1080p (50, 60 Hz),

1080i (50, 60 Hz), 720p (50, 60 Hz), 576p, 576i,

480p, 480i

Audio input (phono jacks)

VIDEO IN 2

Video input (common phono pin with Y input)

HDMI IN 1, 2, 3, 4 (support 4K resolution)

Video (2D): 4096 × 2160p (50, 60 Hz)*,

4096 × 2160p (24 Hz), 3840 × 2160p (50, 60 Hz)*,

3840 × 2160p (24, 25, 30 Hz), 1080p (30, 50,

60 Hz), 1080/24p, 1080i (50, 60 Hz), 720p (30, 50,

60 Hz), 720/24p, 576p, 576i, 480p, 480i, PC

Formats

*YC

bCr 4:2:0 / 8 bit

Video (3D):

Frame Packing: 1080p (30 Hz), 1080/24p,

1080i (50, 60 Hz), 720p (30, 50, 60 Hz), 720/24p

Side-by-Side: 1080p (50, 60 Hz), 1080/24p,

1080i (50, 60 Hz), 720p (50, 60 Hz)

Over-Under: 1080p (30, 50, 60 Hz), 1080/24p,

1080i (50, 60 Hz), 720p (50, 60 Hz)

Audio: 5.1 channel linear PCM: 32, 44.1 and

48 kHz, 16, 20 and 24 bits, Dolby Digital

ARC (Audio Return Channel) (HDMI IN 1 only)

MHL (common with HDMI IN 2/4)

Video (2D): 4096 × 2160p (24 Hz)*, 3840 × 2160p

(24, 25, 30 Hz)*, 1080p (50, 60 Hz)*, 1080p (30 Hz),

1080/24p, 1080i (50, 60 Hz), 720p (30, 50, 60 Hz),

720/24p, 576p, 576i, 480p, 480i

* HDMI IN 2 only

Video (3D):

Frame Packing*: 1080p (30 Hz), 1080/24p, 1080i

(50, 60 Hz), 720p (30, 50, 60 Hz), 720/24p

Side-by-Side: 1080p (50, 60 Hz)*, 1080/24p,

1080i (50, 60 Hz), 720p (50, 60 Hz)

Over-Under: 1080p (50, 60 Hz)*, 1080p (30 Hz),

1080/24p, 1080i (50, 60 Hz), 720p (50, 60 Hz)

* HDMI IN 2 only

Audio: 5.1 channel linear PCM: 32, 44.1 and

48 kHz, 16, 20 and 24 bits, Dolby Digital

DIGITAL AUDIO OUT (OPTICAL)

Digital optical jack (Two channel linear PCM,

Dolby Digital)

HDMI 2 AUDIO IN

Analogue audio input (stereo mini jack)

AUDIO OUT/

Audio output (stereo mini jack)

Headphone jack

(supports Subwoofer out)

1, 2, 3

USB port

LAN

10BASE-T/100BASE-TX connector (Depending on

the operating environment of the network,

connection speed may differ. 10BASE-T/100BASE-

TX communication rate and communication

quality are not guaranteed for this TV.)

Others

Optional accessories

Wall-Mount Bracket: SU-WL500

Wireless subwoofer: SWF-BR100

MHL cable: DLC-MC10/DLC-MC20

Active 3D Glasses: TDG-BT500A

Operating temperature

0 ºC – 40 ºC

Operating humidity

10 % – 80 % RH (non-condensing)

Power and others

Power requirements

220 V - 240 V AC, 50 Hz

Screen size (measured diagonally) (Approx.)

85 inches / 214.8 cm

Display resolution

3,840 dots (horizontal) × 2,160 lines (vertical)

Power consumption

Indicated on the rear of the TV

Output Rating

USB 1, 3: 5 V, 500 mA MAX

USB 2: 5 V, 800 mA MAX

MHL (HDMI IN 2, 4): 5 V, 900 mA MAX

Dimensions (Approx.) (w × h × d)

TV with Floor Stand

1,954 × 1,576 × 591 mm

TV with Table-Top Stand

1,957 × 1,214 × 452 mm

TV without Floor Stand / Table-Top Stand

1,954 × 1,150 × 103 mm

Stand width (Approx.)

Edge position:

TV with Floor Stand

1,953 mm

TV with Table-Top Stand

1,957 mm

Middle position:

694 mm

Mass (Approx.)

TV with Floor Stand

77.0 kg

TV with Table-Top Stand

73.7 kg

TV without Floor Stand / Table-Top Stand

70.8 kg

Note

• Optional accessories availability depends on

countries/region/TV model/stock.

• Design and specifications are subject to change

without notice.

• Power consumption will increase when Port

Replicator connected to the TV.

• This TV set incorporates MHL 2 for HDMI IN 4/MHL

and MHL 3 for HDMI IN 2/MHL.

Trademark information

• The terms HDMI and HDMI High-Definition

Multimedia Interface, and the HDMI Logo

are trademarks or registered trademarks of

HDMI Licensing LLC in the United States

and other countries.

• DLNA®, the DLNA Logo and DLNA

CERTIFIED® are trademarks, service marks,

or certification marks of the Digital Living

Network Alliance.

• Manufactured under license from Dolby

Laboratories.

Dolby and the double-D symbol are

trademarks of Dolby Laboratories.

• “BRAVIA” and are trademarks of

Sony Corporation.

• TrackID is a trademark or registered

trademark of Sony Mobile Communications

AB.

• Gracenote, Gracenote eyeQ, Gracenote

VideoID, Gracenote Video Explore,

Gracenote MusicID, the Gracenote logo

and logotype, and the “Powered by

Gracenote” logo are either registered

trademarks or trademarks of Gracenote in

the United States and/or other countries.

• Opera® Devices SDK from Opera Software

• Wi-Fi, Wi-Fi Direct and Miracast are

trademarks or registered trademarks of

Wi-Fi Alliance.

• “Sony Entertainment Network logo” and

“Sony Entertainment Network” are

trademarks of Sony Corporation.

• MHL, Mobile High-Definition Link and the

MHL Logo are trademarks or registered

trademarks of MHL Licensing, LLC.

• For DTS patents, see

http://patents.dts.com. Manufactured

under license from DTS Licensing Limited.

DTS, the Symbol, & DTS and the Symbol

together are registered trademarks, and

DTS Digital Surround is a trademark of DTS,

• Designed with UEI Technology

Under License from Universal Electronics

• The Bluetooth® word mark and logos are

owned by the Bluetooth SIG, Inc. and any

use of such marks by Sony Corporation is

under license. Other trademarks and trade

names are those of their respective

owners.

• The N Mark is a trademark or registered

trademark of NFC Forum, Inc. in the United

States and in other countries.

• 2014 RealNetworks, Inc. Patents Pending.

trademark of RealNetworks, Inc.

安全資訊 . . . . . . . . . . . . . . . . 2

預先注意事項 . . . . . . . . . . . . . . 4

安裝桌面底座（可替代位置）. . . . . . 5

防止電視機翻倒 . . . . . . . . . . . . . 7

隱藏相機 . . . . . . . . . . . . . . . . 7

使用遙控器 . . . . . . . . . . . . . . 7

顯示觸控板操作指南 . . . . . . . . . . . 7

啟動觸控板教學課程 . . . . . . . . . . . 8

連接其他設備 . . . . . . . . . . . . . 8

將電視機安裝在牆上 . . . . . . . . . 11

故障排除 . . . . . . . . . . . . . . 14

故障及解決方案 . . . . . . . . . . . . 14

規格 . . . . . . . . . . . . . . . . 15

簡介

感謝您購買這項 Sony 產品。

使用電視機之前，請詳閱本手冊，並保留下來以便將來參考。

註

• 使用電視機之前，請詳讀 “ 安全資訊 ”( 第 2 頁 )。

• 關 “ 將電視機安裝在牆上 ” 的指令已包含在這台電視機的說明手

冊。

• 快速設定指南和本說明書中使用的影像和插圖僅作參考並可能與實

際產品的外觀不同。

識別標籤的位置

電視機型號和電源等級的標籤位於電視機背面。

警告

不可將電池曝露於如陽光、火或類似的過熱源。

安裝 / 設定

為了避免火災、觸電或損壞及 / 或受傷等危險，請遵照下列指示來安

裝和使用電視機。

安裝

• 爲了避免滑倒而造成人員受傷，拆封電視機時，請勿踩在電視機保

護袋上。

• 應將電視機安裝在易於插拔的 AC 電源插座附近。

• 將電視機擺在平穩的水平表面上，以防止傾倒而造成人員的傷害或

者損及電視機。

• 將電視機安裝在其不能被拉動、推動或撞翻的地方。

• 合理安裝電視機，使電視機的台式底座不會從電視機座（未提供）

中伸出。

如果台式底座從電視機座中伸出，可能會使電視機翻倒、掉落，造

成人員受傷或損壞電視機。

• 僅可由合格的維修人員執行掛壁安裝。

• 為了安全起見，強烈建議您使用 Sony 配件，包括：

 壁掛式支架 SU-WL500

• 將掛牆式支架安裝於電視機上時，務必要使用隨附於壁掛式支架的

螺絲。隨附螺絲如插圖所示設計從壁掛式支架安裝表面量起。

螺絲的直徑和長度會因為壁掛式支架的型號而有所不同。

使用隨附螺絲以外的螺絲可能會造成電視機內部損壞或者掉落等

等。

本電視設計在香港使用，只保證能在香港使用。

安全資訊

ページが読み込まれています...

Sony KD-85X9500B ユーザーマニュアル

ブランド: Sony

モデル: KD-85X9500B

カテゴリー: 液晶テレビ

タイプ: ユーザーマニュアル

PDFをダウンロードします

報告

他の言語で

English: Sony KD-85X9500B User manual

Sony KD-85X9500B ユーザーマニュアル

Sony KD-85X9500B ユーザーマニュアル

他の言語で

関連論文