Sony M-800V 取扱説明書

カテゴリー
カセットプレーヤー
タイプ
取扱説明書

このマニュアルも適しています

English
B
(a)
C
(b)
(c)
Preparing Power Sources
Choose one of the following power sources.
Dry Batteries (see Fig. A-(a))
Make sure that nothing is connected to the DC IN 3V jack.
1 Open the battery compartment lid.
2 Insert two R03 (size AAA) batteries with correct polarity and
close the lid.
To take out the batteries (see Fig. A-(b))
If the battery compartment lid is accidentally
detached (see Fig. A-(c))
Attach it as illustrated.
When to replace the batteries
For M-800V
Replace the batteries with new ones when the REC/BATT lamp
dims.
For M-850V
Replace the batteries with new ones when the BATT lamp goes
off and the E lamp flashes.
Notes
The unit will play back normally for a while, even after the E lamp
flashes. However, replace the batteries as soon as you can. If you do not,
the playback cannot be made with normal sound, noise may be
recorded and the recorded sound will not be loud enough (M-850V
only).
In the following cases you do not need to replace the batteries:
if the REC/BATT lamp, or BATT lamp flashes with the playback
sound when you turn up the volume.
if the E lamp lights momentarily when the tape starts running or at
the end of the tape (M-850V only).
if the E lamp flashes during FF (CUE) or REW (REVIEW) (M-850V
only).
Battery life* (Approx. hours)
Batteries Recording
Sony manganese R03 (SB) 5 (M-850V) 6 (M-800V)
Sony alkaline LR03 (SG)** 14 (M-850V) 15 (M-800V)
* Measured valued by the standard of JEITA (Japan Electronics and
Information Technology Industries Association) (Using a Sony
Microcassette)
** When using a Sony LR03 (SG) “STAMINA” alkaline dry batteries
(produced in Japan)
Note
The battery life may shorten depending on the operation of the unit.
House current (see Fig. A-(d))
Connect the AC power adaptor to DC IN 3V and to a wall outlet.
Use the AC-E30HG AC power adaptor (not supplied).
Do not use any other AC power adaptor.
Note
Specifications for AC-E30HG vary for each area. Check your local voltage
and the shape of the plug before purchasing.
Recording (see Fig. B-(a))
Make sure that nothing is connected to MIC.
1 Press the reset button of the tape counter.
Note
The number in the tape counter will increase when playing back the
forward side, and decrease when playing back the reverse side.
2 Press Tx, insert a standard microcassette with the side to
start recording facing the lid, and then close the lid. (see Fig.
B-(b)).
3 Select the desired tape speed.
2.4 cm for optimum sound (recommended for normal use):
A 30-minute recording can be made using both sides of the
MC-30 microcassette.
1.2 cm for longer recording time: A 60-minute recording can
be made using both sides of the MC-30 microcassette.
4 Choose recording sides.
To record on both sides
Slide DIR so that the FWD indicator turns
green.
Recording will start form the side facing the
cassette holder window (forward side) and
switches automatically to the reverse side at
the end of the side (Auto Reverse).
Note
Make sure the tabs on both sides are not removed. Even if only the
tab on the reverse side is removed, recording cannot be made.
To record on a single side
Slide DIR so that the REV indicator turns
green.
Recording will start form the side facing the
unit (reverse side).
Note
Make sure the tab on the reverse side is not removed.
5 Set VOR to H, L or OFF.
If you set VOR to H or L, the unit automatically starts
recording the sound and pauses when there is no sound
(you can save tapes and batteries).
H: To record at meeting or in a quiet and/or spacious place.
L: To record for dictation or in a noisy place.
When the sound is not loud enough, set it to OFF, or the unit
may not start recording.
6 Press z.
nN is pressed simultaneously and recording starts. While
the tape runs, the REC lamp (M-850V) or REC/BATT lamp
(M-800V) lights and flashes depending on the strength of the
sound.
Recording level is fixed.
At the end of the reverse side, recording stops and the unit turns
off automatically.
To Press or slide
Stop recording Tx
Start recording during playback z during playback (the unit becomes
in the recording mode)
Review the portion just recorded Push up CUE/REVIEW toward
REVIEW during the recording.
Release the button at the point to start
playback.
Pause recording Slide >PAUSE in the direction of
the arrow.
Take out a cassette Tx
Note
Select the 2.4 cm tape speed for recording, if you play back the recorded
tape with another unit. Otherwise, the sound quality may be changed.
Polarity of the plug
E
D
Notes on recording sides
When recording on both sides, recording will not be made for a few
seconds while the tape is switching sides.
When you open the cassette holder, the direction of the tape is reset to
the forward side.
The DIR switch cannot be used during recording.
Notes on VOR (Voice Operated Recording)
The VOR system depends on the environmental conditions. If you
cannot get the desired results, set VOR to OFF.
When you use the unit in a noisy place, it will stay in the recording
mode. If the sound is too soft, on the contrary, the unit will not start
recording. Set VOR to H (high) or L (low) depending on the conditions.
To monitor the sound
Connect an earphone to the EAR jack. The monitor volume
cannot be adjusted by VOL.
To prevent a cassette from being accidentally recorded
over (see Fig. B-(c))
Break out and remove the cassette tabs. To reuse the cassette for
recording, cover the tab hole with adhesive tape.
Recording cue markers (M-850V only)
While recording, you can record a special signal on the tape to
mark a specific position.
At the desired position, press CUE MARKER to record a signal.
The REC lamp flashes and a signal will be recorded on the tape.
If you want to record a signal longer than that, press CUE
MARKER as long as you want.
During cue and review, you will hear the beep sound at the
signal position. During playback with the headphones plugged
in, you will hear the signal with low frequency sound at the
signal position.
Notes
We recommend recording cue markers when there is a break in the
sound.
The beep may sound differently depending on the marked position on
the tape because the winding speed varies from the beginning to the
end of the tape.
There may be cases that recorded sound is distorted in a portion where
the CUE MARKER signals are recorded.
Playing a Tape (see Fig. C)
1 Insert a cassette with the side to start playing facing the lid.
2 Select the tape speed to the same speed as that used for
recording.
3 Press nN.
4 Turn VOL to adjust the volume.
At the end of the reverse side, playback stops and the unit turns
off automatically.
If you plug in headphones (not supplied) to the EAR jack, you
will get monaural output from both left and right channels.
To Press or slide
Stop playback/stop fast Tx
forward or rewind*
Pause playback Slide >PAUSE in the direction of the
arrow.
Fast forward* Slide CUE/REVIEW toward CUE during stop.
Rewind* Slide CUE/REVIEW toward REVIEW during
stop.
Search forward during Keep CUE/REVIEW pushed down during
playback (CUE) playback and release it at the point you want.
Search backward during Keep CUE/REVIEW pushed up during
playback (REVIEW) playback and release it at the point you want.
Switch playback side DIR
* If you leave the unit after the tape has been wound or rewound, the
batteries will be consumed rapidly. Be sure to depress Tx.
Note
If the tape is completely wound or rewound while searching forward/
backward during playback (CUE/REVIEW), the CUE/REVIEW switch
may not return to the center position when you release the switch. In this
case, push back the switch to the center to start playback.
To increase the playback speed (M-850V only)
Slide the FAST PB switch in the direction of the arrow. The
playback speed will be increased.
To return to the original speed, slide the FAST PB switch to the
original position.
Recording/Playback with the
Connected Equipment
Recording with an External Microphone
Connect a microphone to the MIC jack. Use a microphone of low
impedance (less then 3 k). When using a plug-in-power system
microphone, the power to the microphone is supplied from this
unit.
Note
When recording with an external microphone, the VOR system may not
work properly because of the difference in sensitivity.
Recording from another tape recorder
Connect another tape recorder to the MIC jack using the RK-
G64HG connecting cord (not supplied).
Set this unit to the recording mode and another tape recorder to
the playback mode. In this case set VOR to OFF.
Precautions
On power
Operate the unit only on 3 V DC.
For AC operation, use the AC power adaptor recommended
for the unit. Do not use any other type. For battery operation,
use two R03 (size AAA) batteries.
On the unit
Use only the
(standard microcassettes) with this
unit. Non-standard cassettes cannot be used because their “L”
dimension (see illustration) is different (see Fig. D).
Do not leave the unit in a location near heat sources, or in a
place subject to direct sunlight, excessive dust or mechanical
shock.
Should any solid object or liquid fall into the unit, remove the
batteries or disconnect the AC power adaptor, and have the
unit checked by qualified personnel before operating it any
further.
Keep personal credit cards using magnetic coding or spring-
wound watches etc. away from the unit to prevent possible
damage from the magnet used for the speaker.
When you do not use the unit for long, remove the batteries to
avoid damage caused by battery leakage and subsequent
corrosion.
If the unit has not been used for long, set it in the playback
mode and warm it up for a few minutes before inserting a
cassette.
If you have any questions or problems concerning your unit,
please consult your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks,
consult your nearest Sony dealer.
A cassette cannot be inserted.
t The cassette is being inserted in the wrong way.
t nN has been already pressed.
The unit does not operate.
t The batteries have been inserted with incorrect polarity.
t The batteries are weak. Replace both batteries with new
ones.
t>PAUSE is slid in the direction of the arrow.
t The AC power adaptor is connected to the unit only and
you are going to use the unit on batteries.
Recording cannot be made.
t There is no cassette in the cassette compartment.
t The tab on the tape has been removed. (Even if only the
tab on the reverse side is removed, recording cannot be
made.) To reuse the tape for recording, cover the tab hole
with adhesive tape. To record on one side only, insert a
cassette with the side to start recording facing away from
the lid (reverse side).
t Make sure that the orientation of the cassette and the
setting of DIR does not match in case of one-side
recording. Insert a microcassette with the side to start
recording facing the unit, and then slide DIR so that the
REV indicator turns green.
Recording is interrupted.
t The VOR switch is set to H or L. When you do not use
VOR, set it to OFF.
During CUE/REVIEW the tape stops or does not run.
You cannot fast-forward or rewind.
t The batteries are weak. Replace both batteries with new
ones.
Recording cannot be erased completely.
t The head is contaminated. See “Maintenance”.
Playback cannnot be made.
t The tape has reached the end of the reverse side. Press
nN to switch playback side to FWD.
No sound comes from the speaker.
t The earphone is plugged in.
t The volume is turned down completely.
The sound drops out or comes with excessive noise.
t The volume is turned down completely.
t The batteries are weak. Replace both batteries with new
ones.
t The head is contaminated. See “Maintenance”.
t Direct placement of the cassette tape on the speaker
resulted in magnetization and deteriorated tonal quality.
t Use the unit away from radiowave-emitting devices such
as cellular phones.
The pitch of the sound is unstable.
t The batteries are weak. Replace both batteries with new
ones.
t The capstan and the pinch roller is contaminated. See
“Maintenance”.
Tape speed is too fast or too slow in the playback
mode.
t Improper setting of the TAPE SPEED switch. Set it to the
same speed as that used for recording.
t The batteries are weak. Replace both batteries with new
ones.
Tape speed is faster than the normal playback speed.
t The FAST PB switch (M-850V only) is slid in the direction
of the arrow.
Chattering noise is heard.
t The reset button of the tape counter is accidentally held
and pressed. Press the button again to reset the counter to
“000.”
Rattling noise is heard after the end of the tape is
reached in fast forwarding or rewinding operation.
t Press Tx to stop fast forwarding or rewinding.
Maintenance (see Fig. E)
To clean the tape head and path
Press nN and wipe the head 1, capstan 2 and the pinch
roller 3 with a cotton swab, moistened with alcohol every 10
hours of use.
To clean the exterior
Use a soft cloth slightly moistened in water. Do not use alcohol,
benzine or thinner.
Specifications
Tape
(normal position type)
Recording system
2-track 1-channel monaural
Speaker
Approx. 2.8 cm dia.
Tape speed
2.4 cm/s, 1.2 cm/s
Frequency range
300 - 4 000 Hz (with TAPE SPEED switch at 2.4 cm/s)
Input
Microphone input jack (minijack/PLUG IN POWER)
sensitivity 0.21 mV for 3 k or lower impedance microphone
Output
Earphone jack (minijack) for 8 - 300 earphone
Power output (at 10% harmonic distortion)
250 mW
Power requirements
3 V DC batteries R03 (size AAA) × 2/External DC 3V power sources
Dimensions (w/h/d)
Approx. 58.5 × 100 × 22.5 mm incl. projecting parts and controls
Mass
Approx. 110 g (main unit only)
Supplied accessories
Microcassette tape MC-30 (1) (European model and world model of
M-850V only)
Batteries R03 (SB) (2) (European model and world model of M-850V
only)
Carrying pouch (1) (M-850V and European model of M-800V only)
Design and specifications are subject to change without notice.
nN
> PAUSE
CUE/
REVIEW
Tx
TAPE SPEED
DIR
Non-standard
Approx. 5 mm
Only standard
microcassettes have
a small indention of
side A.
Approx. 2.5 mm
A
(a)
(b)
(c)
(d)
EAR
FAST PB
(M-850V only)
Tape
direction
indicators
About This Manual
The instructions in this manual are for the M-850V and M-800V.
Before you start reading, check your model number. The M-
850V is the model used for illustration purposes. Any
differences in operation are clearly indicated in the text, for
example, “M-850V only”.
to the wall outlet
Standard
Insert the batteries
with correct
polarity.
AC power adaptor (not supplied)
EAR
Microphone
z
> PAUSE
CUE/
REVIEW
Tx
TAPE SPEED
Tape counter
MIC (PLUG
IN POWER)
DIR
VOR
FAST PB
(M-850V only)
CUE MARKER
(M-850V only)
VOL
to DC IN 3 V
BATT/E lamp
(M-850V only)
REC lamp (M-850V only)
REC/BATT lamp
(M-800V only)
Tx
3-238-276-72 (1)
Operating Instructions
M-850V/800V
Sony Corporation ©2002 Printed in China
Microcassette
-
Corder
B
(a)
C
(b)
(c)
E
D
nN
> PAUSE
CUE/
REVIEW
Tx
TAPE SPEED
DIR
A
(a)
(b)
(c)
(d)
EAR
FAST PB
(M-850V
)
Tx
AC
EAR
z
> PAUSE
CUE/
REVIEW
Tx
TAPE SPEED
MIC (PLUG
IN POWER)
DIR
VOR
REC (M-850V )
REC/BATT
(M-800V )
FAST PB (M-850V )
CUE MARKER (M-850V )
VOL
DC IN 3V
BATT/E
(M-850V )
A-(a)
1
2
A-(b)
A-(c)
E
E
E
E
**
*
**
A-(d)
B-(a)
1
2 Tx
B-(b)
3
2.4 cm
1.2 cm
4
5
H:
L:
6 z
nN
Tx
z
>
Tx
B-(c)
C
1
2
3 nN
4
* Tx
>
*
*
*
Tx
D
t
t nN
t
t
t>
t
t
t
t
t
t
t
t nN
t
t
t
t
t
t
t
t
t
t
t
t
t
t Tx
E
1
2 3 nN
  • Page 1 1
  • Page 2 2

Sony M-800V 取扱説明書

カテゴリー
カセットプレーヤー
タイプ
取扱説明書
このマニュアルも適しています

他の言語で