DeWalt DCH333 ユーザーマニュアル

ブランド: DeWalt

モデル: DCH333

カテゴリー: パワードリル

タイプ: ユーザーマニュアル

このマニュアルも適しています

DCH323

DCH333

DCH334

Final page size: A5 (148mm x 210mm)

English (original instructions) 4

简体中文 14

한국어 35

DEWALT

저작권 DEWALT

Fig. A

DCH323

DCH334

图 A

그림 A

Fig. D Fig. E

Fig. B Fig. C

图 D 图 E

图 B 图 C

D E

B C

그림 D 그림 E

그림 B 그림 C

Fig. F Fig. G

1516

DCH334

图 F 图 G

F G

그림 F 그림 G

ENGLISH

English (original instructions)

HEAVY-DUTY CORDLESS ROTARY HAMMERDRILL

DCH323, DCH333, DCH334

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the

most reliable partners for professional power toolusers.

Technical Data

DCH323 DCH333 DCH334

Voltage V

54 54 54

No-load speed min

-1

0–980 0–1000 0–1000

No-load Impact rate bpm 0–4390 0–4480 0–4480

Single impact energy (EPTA 05/2009) J 2.8 3.5 3.5

Maximum drilling range in steel/wood/concrete mm 13/30/28 13/30/30 13/30/30

Tool holdler SDS-Plus SDS-Plus SDS-Plus

Collar diameter mm 54 54 54

Battery Type Li-Ion Li-Ion Li-Ion

Weight (without battery pack) kg 3.6 3.7 3.9

Battery pack DCB546 DCB547 DCB606 DCB609

Battery type Li-Ion Li-Ion Li-Ion Li-Ion

Voltage V

18/54 18/54 20/60 20/60

Capacity A

6.0/2.0 9.0/3.0 6.0/2.0 9.0/3.0

Weight kg 1.05 1.25 1.05 1.25

Charger DCB118

Mains voltage V

220-240

Battery type 10.8/14.4/18 Li-Ion

Approx. charging time of battery packs min 22 (1.3 Ah) 22 (1.5 Ah) 30 (2.0 Ah) 45 (3.0 Ah)

40/60 (4.0 Ah) 50/75 (5.0 Ah) 60 (6.0 Ah) 85 (9.0 Ah)

Weight kg 0.66

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

WARNING: To reduce the risk of injury, read the

instructionmanual.

General Power Tool Safety Warnings



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

ENGLISH

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

Electrical safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

Personal safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

Power tool use and care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the

risk of starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

Battery tool use and care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys,

nails, screws or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

Batteries

Chargers/Charge Times (Minutes)

Cat #

Weight

ENGLISH

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

Additional Safety Instructions for Rotary

Hammers

• Wear ear protectors. Exposure to noise can cause

hearingloss.

• Use auxiliary handles supplied with the tool. Loss of

control can cause personalinjury.

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make exposed metal

parts of the power tool "live" and could give the operator an

electric shock.

• Use clamps or other practical way to secure and support the

workpiece to a stable platform. Holding the work by hand or

against your body is unstable and may lead to loss ofcontrol.

• Wear safety goggles or other eye protection. Hammering

operations cause chips to fly. Flying particles can cause

permanent eye damage. Wear a dust mask or respirator

for applications that generate dust. Ear protection may be

required for mostapplications.

• Keep a firm grip on the tool at all times. Do not attempt

to operate this tool without holding it with both hands. It

is recommended that the side handle be used at all times.

Operating this tool with one hand will result in loss of control.

Breaking through or encountering hard materials such as

re-bar may be hazardous as well. Tighten the side handle

securely beforeuse.

• Do not operate this tool for long periods of time. Vibration

caused by hammer action may be harmful to your hands and

arms. Use gloves to provide extra cushion and limit exposure

by taking frequent restperiods.

• Do not recondition bits yourself. Chisel reconditioning should

be done by an authorized specialist. Improperly reconditioned

chisels could causeinjury.

• Wear gloves when operating tool or changing bits. Accessible

metal parts on the tool and bits may get extremely hot

during operation. Small bits of broken material may damage

barehands.

• Never lay the tool down until the bit has come to a complete

stop. Moving bits could causeinjury.

• Do not strike jammed bits with a hammer to dislodge them.

Fragments of metal or material chips could dislodge and

causeinjury.

• Slightly worn chisels can be resharpened bygrinding.

• Keep the power cord away from the rotating bit. Do not

wrap the cord around any part of your body. An electric cord

wrapped around a spinning bit may cause personal injury and

loss ofcontrol.

Residual Risks

The following risks are inherent to the use of rotary hammers:

• Injuries caused by touching the rotating parts or hot parts of

thetool.

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of squeezing fingers when changing theaccessory.

• Health hazards caused by breathing dust developed when

working in concrete and/ormasonry.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your DeWALT charger is double insulated in

accordance with IEC60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the DeWALT

serviceorganisation.

SAVE THESE INSTRUCTIONS

Chargers

DeWALT chargers require no adjustment and are designed to be

as easy as possible tooperate.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only DeWALT rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.



CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

ENGLISH

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging DeWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard 220-

240V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Charging a Battery (Fig. B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack

6

into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button

7

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to light or by

displaying problem pack or charger blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

ENGLISH

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium-ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in DeWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed

40 ˚C (104 ˚F) (such as outside sheds or metal buildings

in summer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.



WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.



WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation



WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from materials

that could contact them and cause a short circuit.

DeWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests and Criteria.

In most instances, shipping a DeWALT battery pack will be

excepted from being classified as a fully regulated Class 9

Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

All lithium-ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities, DeWALT

does not recommend air shipping lithium-ion battery packs

ENGLISH

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100 Whr.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentation requirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicable regulations.

Transporting the FLEXVOLT

Battery

The DeWALT FLEXVOLT

battery has two modes: Use and

Transport.

Use Mode: When the FLEXVOLT

battery stands alone or is in

a DeWALT 18V product, it will operate as an 18V battery. When

the FLEXVOLT

battery is in a 54V or a 108V (two 54V batteries)

product, it will operate as a 54V battery.

Transport Mode: When the cap is attached to the FLEXVOLT

battery, the battery is in Transport mode. Keep the cap for

shipping.

When in Transport mode, strings

of cells are electrically

disconnected within the pack

resulting in 3 batteries with a

lower Watt hour (Wh) rating as compared to 1 battery with a

higher Watt hour rating. This increased quantity of 3 batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36 Wh, meaning 3

batteries of 36 Wh each.

The Use Wh rating might

indicate 108Wh (1battery implied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Example of Use and Transport Label Marking

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose to water.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

Charge DeWALT battery packs only with designated

DeWALT chargers. Charging battery packs other

than the designated DeWALT batteries with a

DeWALT charger may make them burst or lead to

other dangeroussituations.

Do not incinerate the batterypack.

USE (without transport cap). Example: Wh rating

indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built-in transport cap). Example:

Wh rating indicates 3 x 36 Wh (3batteries of 36 Wh).

Battery Type

The DCH323, DCH333, DCH334 operate on a 54 volt

batterypack.

These battery packs may be used: DCB546, DCB547, DCB606

and DCB609. Refer to Technical Data for moreinformation.

Package Contents

The package contains:

1 Cordless rotary hammerdrill

1 Side handle and depth rod

1 Charger

1 Battery pack (T1, X1)

2 Battery packs (T2, X2)

3 Battery packs (T3, X3)

1 Keyless chuck (DCH334)

1 Kit box

ENGLISH

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Visible radiation. Do not stare intolight.

Date Code Position

The date code, which also includes the year of manufacture, is

printed into thehousing.

Example:

2017 XX XX

Year of Manufacture

Description (Fig.A)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

Variable speed switch

Forward/reverse button

Mode selector dial

Mode selector button

Side handle

Battery pack

Release button

Main handle

SDS-Plus tool holder

Sleeve

Depth rod

Depth rod release button

Worklight

Utility hook

Intended Use

Your cordless rotary hammerdrill has been designed for

professional drilling and hammerdrilling applications, as well as

screwdriving and chippingapplications.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

Your cordless rotary hammerdrill is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Overload Clutch

In case of jamming of a drill bit, the drive to the drill spindle is

interrupted. Because of the resulting forces, always hold the

tool with both hands and take a firmstance. After the overload,

release and depress the trigger to re-engagedrive.

Mechanical Clutch

These tools are fitted with a mechanical clutch. The indication

that the clutch has activated will be an audible ratcheting

together with increasedvibration.

Anti-Rotation System (Fig. E)

In addition to the clutch, an anti-rotation system offers increased

user comfort and safety through an on-board, anti-rotation

technology capable of detecting if the user loses control of

thehammer. When a jam is detected, the torque and speed are

reducedinstantly. This feature prevents self rotation of the tool

reducing the occurrence of wristinjuries.

The anti-rotation system indicator

18

will illuminate to

indicatestatus.

Indicator Diagnosis Solution

OFF Tool is functioning

normally

Follow all warnings and instructions

when operating the tool.

SOLID Anti-Rotation

System has

been activated

(ENGAGED)

With the tool properly supported,

release trigger. The tool will function

normally when the trigger is depressed

again and the indicator light will go out

Active Vibration Control

For best vibration control, hold the tool as described in Proper

HandPosition.

The active vibration control neutralises rebound vibration from

the hammer mechanism. Lowering hand and arm vibration,

it allows more comfortable use for longer periods of time and

extends the life of theunit.

The hammer only needs enough pressure to engage the active

vibraton control. Applying too much pressure will not make

the tool drill or chip faster and active vibration control will

notengage.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments/accessories or when making

repair. An accidental start-up can causeinjury.



WARNING: Use only DeWALT battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack

6

is fullycharged.

ENGLISH

To Install the Battery Pack into the

Tool Handle

1. Align the battery pack

6

with the rails inside the tool’s

handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

7

and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs

Some DeWALT battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button

19

. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Side Handle (Fig.A)



WARNING: To reduce the risk of personal injury, ALWAYS

operate the tool with the side handle properly installed.

Failure to do so may result in the side handle slipping

during tool operation and subsequent loss of control. Hold

tool with both hands to maximizecontrol.

The side handle

5

clamps to the front of the gear case and

may be rotated 360˚ to permit right- or left-hand use. The side

handle must be tightened sufficiently to resist the twisting

action of the tool if the accessory binds or stalls. Be sure to grip

the side handle at the far end to control the tool during astall.

To loosen side handle, rotatecounterclockwise.

To Adjust the Depth Rod (Fig. C)

1. Push in and hold the depth rod release button

12

on the

sidehandle.

2. Move the depth rod

11

so the distance between the

end of the rod and the end of the bit equals the desired

drillingdepth.

3. Release the button to lock rod into position. When drilling

with the depth rod, stop when end of rod reaches surface

ofmaterial.

Utility Hook (Fig.A,D)

A utility hook

14

is fitted below the main handle

8

on the left

side of the tool. To extend the utility hook pull it out from the

side of the tool. To store the utility hook push it back flush with

the side of thetool. If use of the hook is not desired at all, it can

be removedcompletely.

To Remove and/or Reinstall the

Utility Hook

1. Position the utility hook into the extended position and

remove the hex head screw located on the underside of the

mainhandle.

2. Pull out the utility hook until it is free from theunit.

3. To reinstall, insert the utility hook into the the slot below the

mainhandle.

Bit and Bit Holder



WARNING: Burn Hazard. ALWAYS wear gloves when

changing bits. Accessible metal parts on the tool and bits

may get extremely hot during operation. Small bits of

broken material may damage barehands.

The hammerdrill can be fitted with different bits depending on

the desired application. Use sharp drill bitsonly.

Bit Reccomendations

• For wood, use twist bits, spade bits, power auger bits or

holesaws.

• For metal, use high-speed steel twist drill bits or holesaws.

Use a cutting lubricant when drilling metals. The exceptions

are cast iron and brass which should be drilleddry.

• For masonry, such as brick, cement, cinder block, etc., use

carbide-tipped bits rated for percussiondrilling.

SDS-Plus Bit Holder (Fig. F)

NOTE: Special adapters are needed to use the SDS-plus tool

holder with straight shank bits and hexagonal screwdriver bits.

Refer to OptionalAccessories.

To insert a drill bit or other accessory:

1. Insert the shank of the bit about 19mm into SDS-Plus

toolholder.

2. Push and rotate bit until it locks in place. The bit will be

securelyheld.

3. To release bit, pull the sleeve

10

back and remove thebit.

Keyless Chuck (Fig. F, G)

DCH334

On some models, a keyless chuck can be installed in place of the

SDS-Plus bitholder.



WARNING: Never use standard chucks in the rotary

hammeringmode.

Replacing the SDS-Plus Bit Holder with the Keyless Chuck

1. Select hammering only mode (see Operation Modes), this

locks the spindle to prevent it from rotating when unlocking

the removable toolholder.

2. Turn the locking collar

15

into the unlocked position and

pull the installed bit holderoff.

3. Push the keyless chuck

16

onto the spindle

17

and turn

the locking collar into the lockingposition.

4. To replace the keyless chuck with the SDS-Plus bit holder,

first remove the keyless chuck the same way as the SDS-

Plus bit holder was removed. Then replace the SDS-Plus

bitholder the same way as the keyless chuck wasreplaced.

ENGLISH

To insert a drill bit or other accessory in keyless chuck:

1. Grasp the sleeve

16

of the chuck with one hand and use

the other hand grasping the base of thechuck.

2. Rotate the sleeve counterclockwise (as viewed from the

front) far enough to accept the desiredaccessory.

3. Insert the accessory about 19mm into the chuck and

tighten securely by rotating the chuck sleeve clockwise

with one hand while holding the tool with the other hand.

Continue to rotate the chuck sleeve until several ratchet

clicks are heard to ensure full grippingpower.

Be sure to tighten chuck with one hand on the chuck sleeve and

one hand holding the tool for maximum tightness.

To release the accessory, repeat Steps 1 and 2above.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments/accessories or when making

repair. An accidental start-up can causeinjury.

Proper Hand Position (Fig.E)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main handle

8

with the other hand on the side handle

5

Operation Modes (Fig.A)



WARNING: Do not select the operating mode when the

tool isrunning.

Your tool is equipped with a mode selector dial 

3

to selectthe

mode appropriate to desiredoperation.

Symbol Mode Application

Rotary Drilling

Screwdriving

Drilling into steel, wood

andplastics

Rotary

Hammering

Drilling into concrete and

masonry

Hammering

only

Lightchipping

To select an operating mode:

1. Depress the mode selector release button

4

2. Rotate the mode selector dial so that the arrow points to the

symbol corresponding with the desiredmode.

NOTE: The mode selector

3

must be in rotary drilling, rotary

hammering or hammering only mode at all times. There are no

operable positions inbetween. It may be necessary to briefly

run the motor after having changed from 'hammering only' to

'rotary' modes in order to align thegears.

Performing an Application (Fig.A)



WARNING: TO REDUCE THE RISK OF PERSONAL

INJURY, ALWAYS ensure workpiece is anchored or

clamped firmly. If drilling thin material, use a wood “back-

up” block to prevent damage to thematerial.



WARNING: Always wait until the motor has come to

a complete standstill before changing the direction

ofrotation.

1. Choose and install the appropriate chuck, adapter, and/or

bit onto to the tool. Refer to Bit and BitHolders.

2. Using the mode selector dial

3

, selectthe mode

appropriate to desired application. Refer to

OperationModes.

3. Adjust the side handle

5

asrequired.

4. Place the bit/chisel on the desiredlocation.

5. Select the direction ofrotation using the forward/reverse

button

2

. When changing the position of the control

button, be sure the trigger isreleased.

- To select forward rotation, press the for ward/re verse

control button on the right side of thetool.

- To select reverse, press the forward/reverse control

button on the left side of thetool.

NOTE: The center position of the control button locks

the tool in the offposition.

6. Depress the trigger switch

1

. The farther you depress

the trigger switch, the faster the tool will operate. For

maximum tool life, use variable speed only for starting holes

orfasteners.

NOTE: Depending on your tool, depressing the trigger

switch activates a worklight

13

designed to illuminate the

immediate work surface. Refer to Description. The worklight

will automatically turn off 20 seconds after the trigger

switch isreleased.



WARNING:

• Do not use this tool to mix or pump easily combustible

or explosive fluids (benzine, alcohol, etc.).

• Do not mix or stir inflammable liquids

labelledaccordingly.

MAINTENANCE

Your DeWALT power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments/accessories or when making

repair. An accidental start-up can causeinjury.

ENGLISH

The charger and battery pack are notserviceable.

Lubrication

Your power tool requires no additionallubrication.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Optional Accessories



WARNING: Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only DeWALT recommended

accessories should be used with thisproduct.

Various types of SDS-Plus drill bits and chisels are available as

anoption. Accessories and attachments used must be regularly

lubricated around the SDS-Plusfitment.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

our environment:

• Run the battery pack down completely, then remove it from

thetool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

简体中文

定义：安全指南

下列定义描述了各标志术语的严重程度。请仔细阅读

本手册，并注意这些标志。



危险：表示存在紧急危险情况，如果不加以

避免，将导致死亡或严重伤害。



警告：表示存在潜在的危险情况，如果不加

以避免，可能导致死亡或严重伤害。



警示：表示存在潜在危险情况，如果不加以

避免，可能导致轻度或中度伤害。

注意：表示存在不涉及人身伤害的情况，如果

不加以避免，可能导致财产损失。



表示存在触电风险。



表示存在火灾风险。

警告：为降低伤害风险，请阅读使用手册。

60V 锂电无刷电锤

DCH323, DCH333, DCH334

恭喜！

您已选择了得伟工具。凭借多年的产品开发和创新经验，得伟已经成为专业电动工具用户最可靠的合作伙伴

之一。

技术参数

DCH323 DCH333 DCH334

电压伏特

直流

60 60 60

空载转速转/分 0–980 0–1000 0–1000

空载冲击率 bpm 0–4390 0–4480 0–4480

冲击能量（EPTA 05/2009） J 2.8 3.5 3.5

钢材/木材/混凝土中最大钻深毫米 13/30/28 13/30/30 13/30/30

工具夹持器 SDS-Plus SDS-Plus SDS-Plus

轴环直径毫米 54 54 54

电池类型锂电锂电锂电

重量（不含电池组）千克 3.6 3.7 3.9

电池组 DCB546 DCB547 DCB606 DCB609

电池类型锂电锂电锂电锂电

电压伏特

直流

18/54 18/54 20/60 20/60

电池容量安

时

6.0/2.0 9.0/3.0 6.0/2.0 9.0/3.0

重量千克 1.05 1.25 1.05 1.25

充电器 DCB118

电源电压伏特

交流

220-240

电池类型 10.8/14.4/18 锂离子

电池组的大约充电时间分钟 22( 1.3 安时） 22( 1.5 安时） 30( 2.0 安时） 45( 3.0 安时）

40/60( 4.0 安时） 50/75( 5.0 安时） 60( 6.0 安时） 85( 9.0 安时）

重量千克 0.66

简体中文

电动工具通用安全警告



警告！阅读随电动工具提供的所有安全警告、

说明、图示和规定。不遵照以下所列说明会导

致电击、着火和／或严重伤害。

保存所有警告和说明书以备查阅。

警告中的术语“电动工具”指市电驱动（有线）电动工

具或电池驱动（无线）电动工具。

工作场地的安全

1 )

保持工作场地清洁和明亮。杂乱和黑暗的场地

会引发事故。

2 )

不要在易爆环境，如有易燃液体、气体或粉尘

的环境下操作电动工具。

电动工具产生的火花

会点燃粉尘或气体。

3 )

操作电动工具时，远离儿童和旁观者。注意力

不集中会使你失去对工具的控制。

电气安全

1 )

电动工具插头必须与插座相配。绝不能以任何

方式改装插头。需接地的电动工具不能使用任

何转换插头。未经改装的插头和相配的插座将

降低电击风险。

2 )

避免人体接触接地表面，如管道、散热片和

冰箱。如果你身体接触接地表面会增加电击风险。

3 )

不得将电动工具暴露在雨中或潮湿环境中。

水进入电动工具将增加电击风险

4 )

不得滥用软线。绝不能用软线搬运、拉动电动工

具或拔出其插头。使软线远离热源、油、锐边或

运动部件。受损或缠绕的软线会增加电击风险。

5 )

当在户外使用电动工具时，使用适合户外使用的

延长线。适合户外使用的电线将降低电击风险。

6 )

如果无法避免在潮湿环境下操作电动工具，

应使用带有剩余电流装置（RCD）保护的电源。

RCD的使用可降低电击风险。

人身安全

1 )

保持警觉，当操作电动工具时关注所从事的

操作并保持清醒。当你感到疲倦，或在有药物、

酒精或治疗反应时，不要操作电动工具。在操

作电动工具时瞬间的疏忽会导致严重人身伤害。

2 )

使用个人防护装置。始终佩戴护目镜。防护装置，

诸如适当条件下使用防尘面具、防滑安全鞋、

安全帽、听力防护等装置能减少人身伤害。

3 )

防止意外起动。在连接电源和/或电池盒、拿起

或搬运工具前确保开关处于关断位置。手指放

在开关上搬运工具或开关处于接通时通电会导

致危险。

4 )

在电动工具接通之前，拿掉所有调节钥匙或

扳手。遗留在电动工具旋转零件上的扳手或钥匙

会导致人身伤害。

5 )

手不要过分伸展。时刻注意立足点和身体平衡。

这样能在意外情况下能更好地控制住电动工具。

6 )

着装适当。不要穿宽松衣服或佩戴饰品。让你

的头发和衣服远离运动部件。宽松衣服、佩饰

或长发可能会卷入运动部件。

7 )

如果提供了与排屑、集尘设备连接用的装置，

要确保其连接完好且使用得当。使用集尘装置

可降低尘屑引起的危险。

8 )

不要因为频繁使用工具而产生的熟悉感而掉以

轻心，忽视工具的安全准则。某个粗心的动作

可能在瞬间导致严重的伤害。

电动工具使用和注意事项

1 )

不要勉强使用电动工具，根据用途使用合适的

电动工具。选用合适的按照额定值设计的电动

工具会使你工作更有效、更安全。

2 )

如果开关不能接通或关断电源，则不能使用该

电动工具。不能通过开关来控制的电动工具是

危险的且必须进行修理。

3 )

在进行任何调节、更换附件或贮存电动工具

之前，必须从电源上拔掉插头和／或卸下电池包

（如可拆卸）。这种防护性的安全措施降低了电动

工具意外起动的风险。

4 )

将闲置不用的电动工具贮存在儿童所及范围

之外，并且不允许不熟悉电动工具和不了解这些

说明的人操作电动工具。电动工具在未经培训的

使用者手中是危险的。

5 )

维护电动工具及其附件。检查运动部件是否调

整到位或卡住，检查零件破损情况和影响电动

工具运行的其他状况。如有损坏，应在使用前

修理好电动工具。许多事故是由维护不良的电

动工具引发的。

6 )

保持切削刀具锋利和清洁。维护良好地有锋利

切削刃的刀具不易卡住而且容易控制。

7 )

按照使用说明书，并考虑作业条件和要进行的

作业来选择电动工具、附件和工具的刀头等。

将电动工具用于那些与其用途不符的操作可能

会导致危险情况。

8 )

保持手柄和握持表面干燥、清洁，不得沾有油

脂。在意外的情况下，湿滑的手柄不能保证握

持的安全和对工具的控制。

简体中文

电池式工具使用和注意事项：

1 )

仅使用生产者规定的充电器充电。

将适用于某

种电池包的充电器用到其他电池包时可能会发

生着火危险。

2 )

仅使用配有专用电池包的电动工具。使用其他电

池包可能会产生伤害和着火危险。

3 )

当电池包不用时，将它远离其他金属物体，

例如回形针、硬币、钥匙、钉子、螺钉或其他

小金属物体，以防电池包一端与另一端连接。

电池组端部短路会引起燃烧或着火。

4 )

在滥用条件下，液体可能会从电池组中溅出，

应避免接触。如果意外碰到液体，用水冲洗。

如果液体碰到了眼睛，还要寻求医疗帮助。

从电池中溅出的液体可能会发生腐蚀或燃烧。

5 )

不要使用损坏或改装过的电池包或工具。损坏

或改装过的电池组可能呈现无法预测的结果，

导致着火、爆炸或伤害。

f )

不要将电池包暴露于火或者高温中。电池包暴

露于火或高于 130°C的高温中可能导致爆炸。

维修

1 )

让专业维修人员使用相同的备件维修电动工具。

这将保证所维修的电动工具的安全。

2 )

决不能维修损坏的电池包。电池包仅能由生产

者或其授权的维修服务商进行维修。

电锤专用警告语：

戴好耳罩。暴露在噪声中会引起听力损伤。

使用随工具提供的辅助手柄。操作失手会引起人身伤害。

在切削附件可能触及暗线进行操作时，要通过绝缘握

持面来握持工具。切削附件碰到带电导线会使工具外

露的金属零件带电从而使操作者受到电击。

电锤的附加安全守则

•

使用夹具或采取其它可行的方法，将工件固定、

支撑到稳定的平台上。手持或用身体顶住工件都是

不稳定的，会导致操作失控。

•

请佩戴安全护目镜或其他护目装备。冲击操作会

导致碎片飞散。飞散的颗粒会对眼睛造成永久性

伤害。请在产生粉尘的应用环境佩戴防尘面具或

口罩。大多应用环境需要佩戴听力保护器。

•

时刻紧握工具。切勿尝试在不使用双手握住工具时

操作此工具。建议始终使用侧手柄。单手操作此工

具会导致失控。穿透或遇到坚硬材料（如钢筋）也

可能会发生危险。使用前请务必稳固转紧侧手柄。

•

不要长时间操作此工具。锤击操作导致的振动可

能会伤害您的手部和手臂。使用手套提供额外缓

冲，经常停下休息，限制使用时间。

•

切勿自行整修钻头。凿子的整修工作应由授权专

业人员来完成。凿子整修不当可能会导致伤害。

•

操作工具或更换钻头时请佩戴手套。工具和钻头

上的可接触金属部件可能会在操作过程中变得非

常热。少量破碎材料可能会导致双手受伤。

•

直到钻头完全停止运动才放下工具。运动钻头可

能会导致伤害。

•

请勿使用锤子击打卡住的钻头。金属碎片或材料

碎屑可能会弹出而导致伤害。

•

轻度磨损的凿子可通过打磨进行磨尖。

•

让电线远离旋转中的钻头。请勿用身体的任何部

位缠绕电线。缠绕在旋转中的钻头周围的电线可

能会导致人身伤害和失控。

其他风险

使用电锤时具有下列固有危险：

•

碰触工具的旋转部件或发热部件会导致人身伤害

尽管遵守了相关的安全法规并采用了安全装备，某些

其他风险仍然是无法避免的。这些风险包括：

•

听力损伤。

•

更换附件时夹到手指的风险。

•

在混凝土和/或砖石环境中工作时，吸入粉尘导致

的健康危害。

电气安全

电机只适用一种工作电压。请务必检查电池组的电压

是否和铭牌上的电压一致。另外，请确保充电器电压

和主电源的电压一致。

得伟充电器符合 IEC60335 双重绝缘要求，因此

无需使用接地线。

若电源线损坏，必须交由得伟维修部门采用专门制备

的电线进行更换。

请妥善保管好这些说明

充电器

得伟充电器无需做出任何调整，专为简易操作而设计。

针对所有电池充电器的重要安全说明

请妥善保管好这些说明：

本手册包含重要的兼容电池

充电器安全和操作说明（请参阅

技术参数

）。

•

在使用充电器之前，请先阅读所有指示以及充

电器、电池组和使用电池组的产品上的警示标记。



警告：触电危险。请勿让任何液体渗入充电器，

否则会引起触电。



警告：我们建议使用漏电保护额定电流为 30 毫

安或以下的漏电保护装置。

简体中文



警示：灼伤危险。为降低人身伤害风险，请仅

使用得伟充电式电池充电。使用其它类型的电

池可能会引起爆裂，并导致人身伤害和损害。



警示：应看管好儿童，以确保他们不将此设备

当做玩具来玩。

注意：在某些情况下，当充电器的插头插入电

源插座时，充电器内部裸露的充电接触点可能

因为外来物件而短路。请勿让能导电的异物靠

近充电器腔，这些外来物件包括但不限于钢棉、

铝箔或任何金属颗粒的堆积物。充电器内没有

电池组时，请断开充电器与电源的连接。清洗

前，务必拔掉充电器。

•

请勿试图使用本手册指定的充电器以外的其他任

何充电器为电池组充电。充电器和电池组都是专

门设计的，互相配合使用。

•

除了为得伟充电式电池充电以外，这些充电器并

非设计用于其他用途。否则，可能会导致火灾、

触电或电击。

•

请勿将充电器暴露于雨中或雪中。

•

断开充电器连接时，应拔下插头，切勿拉拽电源线。

这将降低对电插头和电线的损害风险。

•

确保电源线布置在不易踩踏、踢绊或会受到损害

或压力的位置。

•

除非绝对必要，否则请勿使用延长线。使用不正确

的延长线可能导致火灾、触电或电击的风险。

•

请勿将任何物件放在充电器上面，或是把充电器

放在可能会堵住通风槽的柔软表面，导致充电器

的内部过热。请把充电器放置在远离任何热源的

地方。充电器通过外壳顶端和底端的槽进行通风。

•

禁止使用电源线或插头已损坏的充电器。请立即

更换这些充电器。

•

如果充电器受到强烈重击、掉落或出现其他损坏

情况，请勿使用充电器。请将损坏的充电器送到授

权服务中心。

•

请勿自行拆卸充电器。请将需要检修或修理的充

电器送到授权服务中心。重装不正确可能导致触电、

电击或火灾风险。

•

必须立即将已损坏的电源线交由制造商、服务代

理或类似的合格人员进行更换以防止安全隐患。

•

清洁前，请先断开充电器和插座的连接，以降低触

电风险。取出电池组不会降低此风险。

•

切勿将两个充电器连接在一起。

•

充电器是为 220-240 V 的标准家用电源而设计。

请勿试图在任何其他电压下使用充电器。此规则不

适用于车载充电器。

使用延长线

除非绝对必要，否则请勿使用延长线。使用适合您的

充电器输入功率的合格延长线（见

技术参数

）。最小的

导线尺寸为 1 平方毫米；最大长度为 30 米。

使用电缆卷筒时，请务必拉出所有的电缆。

为电池充电（图 B）

放进电池组前，先将充电器的插头插到相应的电源

插座上。

将电池组

插入到充电器中，确定电池组完全就位。

红色（充电中）指示灯将不断闪烁，表示充电过程

已经开始。

红色灯持续亮起表示充电完成。此时电池组已完全

充电，您可以使用电池组或将电池组留在充电器上。

要从充电器上取下电池组，请按下电池组上的电池

释放按钮

。

注：为了确保锂离子电池的效能和使用寿命最大化，

在首次使用电池组之前必须将其完全充电。

充电器操作

关于电池组的充电状态，请参阅以下指示灯说明。

充电状态指示灯

充电中

已完全充电

热/冷电池组延迟*

* 红色指示灯会继续闪烁，但黄色指示灯在本次操作过

程中会亮起。电池组达到适当温度后，黄色指示灯会

熄灭，充电器将恢复充电程序。

此兼容充电器不能为故障的电池组充电。充电器指示

灯不亮或“故障的电池组或充电器”指示灯闪烁时，

表示电池有故障。

注：这也可能意味充电器有故障。

如果充电器提示存在故障，请将充电器和电池组送到

授权的维修中心进行测试。

热/冷电池组延迟

当充电器检测到电池组过热或过冷时，它会自动启动

热/冷电池延迟模式，暂停充电，直到电池组达到适当

的温度。然后，充电器会自动切换到电池组充电模式。

此功能可确保电池组拥有最长的使用寿命。

冷电池组充电速度比热电池组充电速度慢。电池组在

整个充电周期的充电速度都会较慢，即使电池组升温

也不会恢复到最大速度。

DCB118 充电器配备专用于冷却电池组的内部风扇。

电池组需要冷却时，风扇会自动启动。如果风扇运转

不正常或通风槽堵塞，切勿操作充电器。请勿让异物

进入充电器内部。

简体中文

电子保护系统

XR 锂离子电池工具具有电子保护系统设计，可保护电

池组免受过载、过热或过度放电之害。

如果电子保护系统处于运作状态，该工具将自动停止

操作。如果发生这种情况，请将锂离子电池组放在充

电器上，直至其完全充电。

壁挂式安装

这些充电器设计为可以安装在墙上，也可以直立在桌面

或工作台面上。如果安装在墙上，请确保充电器的位置

可以连接到电源插座，并且远离墙角或其他可能妨碍空

气流通的障碍物。将充电器背面作为在墙上安装螺丝的

位置模板。使用至少 25.4 毫米长、螺丝帽直径至少 7-9 毫

米的石膏板螺丝（单独购买）牢牢固定充电器，将螺丝

最大限度钉入木材，预留约 5.5 毫米露在墙外。将充电器

背面的安装槽对准露出的螺丝，完全放置到位。

充电器清洁说明



警告：触电危险。清洁前，请将充电器从交流

电源插座上拔下。可用布或非金属软刷清除充

电器外部的污垢和油脂。请勿使用水或任何清

洁剂。切勿让任何液体渗入工具，切勿让工具

的任何部件浸在液体中。

充电时间

针对所有电池组的重要安全说明

在订购更换电池组时，请务必附上目录型号和电压。

包装箱内的电池组并未完全充电。使用电池组和充电器

之前，请阅读下列安全指示，然后遵循所述的充电程序。

请阅读所有说明

•

请勿在易爆环境，如有易燃液体、气体或粉尘的环

境中充电或使用电池。在充电器中插入或取出电

池时可能会点燃粉尘或气体。

•

切勿强行将电池放进充电器。请勿以任何方式改

装电池组以在不相容的充电器中使用，否则电池

组可能会破裂，导致严重人身伤害。

•

只使用得伟充电器为电池组充电。

•

请勿喷溅电池组或将其浸泡在水或其他液体中。

•

请勿在温度可能达到或超过 40˚C（104˚F）的地方

（如夏天户外的棚子或金属建筑物中）存储或使用

工具和电池组。

•

即使电池组严重受损或完全损坏，也请勿焚化电

池组。电池组在火中会发生爆炸。锂离子电池组在

燃烧时会释放有毒烟雾和物质。

•

如果电池液体接触到皮肤，请立即以中性肥皂和清

水冲洗接触的地方。如果电池液体不慎进入眼睛，

应睁开眼睛并用清水冲洗至少 15 分钟或直到刺激感

消失。如果需要医疗救助，请告知医护人员。电池

电解质由液状有机碳酸盐和锂盐的混合物组成。

•

已打开电池的内部物质可能导致呼吸道刺激。

请保持空气流通。如果症状持续存在，请就医。



警告：灼伤危险。电池液如果接触到火花或火

焰可能会燃烧。



警告：切勿以任何理由试图打开电池组。电池

组外壳破裂或损坏时，请勿将电池组插入充电

器。请勿挤压、掉落或损坏电池组。请勿使用

受过强烈重击、掉落、碾压或以任何其它方式

（如被钉子穿破、受到锤子的重击、踩踏）受损

的电池组或充电器。否则可能会引起触电或

电击。损坏的电池组应送回维修中心进行回收。



警告：火灾危险。请勿在存储或搬运电池组时让

金属物品接触暴露的电池两极。例如，请勿将

电池组放在围裙、口袋、工具盒、产品套件盒、

抽屉等可能与散钉、螺丝、钥匙等物品接触的

地方。



警示：不用时，将工具侧放在平稳的表面上，

确保不会有踢绊或掉落的危险。一些具有大型

电池组的工具将直立于电池组之上，但可能会

轻易被撞倒。

运输



警告：火灾危险。电池运输途中，如果电池两

极意外接触导电材料，可能会引发火灾。运输

电池时，务必保护电池两极，确保与可能接触

电池导致短路的材料良好绝缘。

得伟电池符合所有适用的行业和法律标准规定的运输

规范，包括《联合国危险品运输建议规章范本》

（UN Recommendations on the Transport of Dangerous Goods）、

《国际航空运输协会（IATA）危险品规则》（International Air

Transport Association（IATA）Dangerous Goods Regulations）、

《国际海运危险品（IMDG）规则》（International Maritime

Dangerous Goods（IMDG）Regulations）和《欧洲危险货物

国际公路运输协定》（European Agreement Concerning The

International Carriage of Dangerous Goods by Road）（ ADR）。

锂离子电池和电池组已遵循《联合国危险品运输建议

规章范本手册》第 38.3 节关于测试和标准的说明通过

测试。

大多数情况下，发运得伟电池组不属于完全管制的 9

类危险品。通常情况下，只有当运输包含一个能量等

级大于 100 瓦时（Wh）的锂离子电池时，才需要作为完

全管制的 9 类危险品发运。所有锂离子电池外壳上均

标注有瓦时等级。此外，由于法规比较复杂，无论瓦

时等级是多少，得伟都不建议单独空运锂离子电池组。

发运包含电池的工作（组合套件）时，如果电池组的能

量等级不大于 100 瓦时（Wh），则可以按计划空运。

ページが読み込まれています...

DeWalt DCH333 ユーザーマニュアル

ブランド: DeWalt

モデル: DCH333

カテゴリー: パワードリル

タイプ: ユーザーマニュアル

このマニュアルも適しています

PDFをダウンロードします

報告

他の言語で

English: DeWalt DCH333 User manual

その他のドキュメント

Abicor Binzel Gouging electrodes ABIARC 商品情報

DeWalt DCH333 ユーザーマニュアル

このマニュアルも適しています

DeWalt DCH333 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント