多功能便携式音箱
SE108
SE108W
使用说明书
中国地区 SE108 服务专线
150-0087-2738
www.superlux.com.tw
•驱动单元：低音：8"(20.32cm)/ 高音：1"(2.54cm)
•功 率：4 0 W
•频率响应（-10dB):55-20kHz
•输入灵敏度：麦克风：-38dBu/线性输入 :0dBu
•最 大 峰 值音 压：1 1 0 d B S P L
•分 频 点：4 k H z
•输入：6.3mm 线性输入麦克风，3.5mmAUXIN 音频输入
•阻抗：麦克风 =1.65K,线性输入 =22.5K
小心操作
•不要将你的手指或手插入调音面板上端口的任何缝隙或开口。
•避免将外部杂物（纸张、塑料、金属等）插入或掉入调音面板上的任何缝隙或开口处和音箱端口。
如果发生这种情况，请立即关闭电源
•请勿将身体压在本设备上或在其上放置重物。操作按钮、开关或插口时要避免过分用力。
•请勿长时间持续在过高的音量下使用耳机，否则可能会造成永久性听力损害。如果遇到失聪或耳
鸣的情况，请寻求医治。
•如果声音失真，请勿使用本设备。在这种状态下继续使用可能会造成设备过热并引起损坏，建议
重新 调整设备。
•不要拖拽任何已连接的连接线，比如话筒线。否则可能造成音箱倾倒摔落，导致设备损坏或人身
意 外 伤害。
•材质：P P
•输出：耳机输出
•RMS 输出功率：40W/4Ω( ＠ THD<1%at1KHz)
•总谐波失真：≤ 0.3%@20-20,000Hz,+14dBu
•电池：12V/7.5AH(内含适配器 )
•尺寸（HxWxD):441x330x262mm
• 重 量：1 0 K G
技术参数
电池充电 连接蓝牙 外观
将音箱安装到音箱架上
应用 REVERB 混响效果
注意事项
保养维护 在对本设备进行清洁时，请务必切断电源。
第一次使用前，务必要充电 4 至 5 小时。
请按照以下步骤将蓝牙设备和 SE108/SE108W 做配对
＊长时间不使用时，需每三个月充电一次，以延长电池寿命
!
请在操作使用前，首先仔细阅读下述内容
* 请将本说明书存放在安全的地方，以便将来随时参阅。
警告
为了避免因触电、短路、损伤、火灾或其它危险可能导致的严重受伤甚至死亡，请务必遵守下列基本
注意事项。这些注意事项包括但不限于下列情况
电源 / 电源线
•请勿将电源线放在热源如加热器或散热器附近，不
要过分弯折或损伤电源线，不要在其上加压重物，
不要将其放在可能被踩踏引起绊倒或可能被碾压的
地 方。
•只能使用附带的电源线 /插头。
•定期检查电源插头，擦除插头上积起来的脏物或灰
尘。
请勿打开
•除电池可以自行更换外。请勿打开本设备或试图拆
卸其内部零件或进行任何方式的改造。若出现异常，
请立即停止使用，并请向 Superlux 代理商联系咨询
关于潮湿警告
•请勿让本设备淋雨或在水附近及潮湿环境中使用，
或将盛有液体的容器（如花瓶、瓶子或玻璃杯）放在
其上，否则可能会导致液体溅入任何开口。如果水
等任何液体渗入本设备，请立即切断电源。然后请
与 Superlux 代理商联系咨询
•切勿用湿手插拔电源线插头。
火警
•请勿在设备上放置燃烧着的物体，比如蜡烛。燃烧
的 物 体 可 能 会 倾 倒 并 引 发 火 灾。
当意识到任何异常情况时
•当出现以下任何一种问题时，请立即关闭电源开
关并从电源插座中拔出电源线插头。然后请向
Superlux 代理商咨询。
•散发出异常气味 或冒烟。
•当物体掉入设备中。
•使用设备过程中声音突然中断。
为避免本产品可能受到的损坏或发生故障 , 请注意下列事项。
操作和维护
•为了避免操作面板发生变形、不稳定操作或损坏内部元件，请勿将本设备放在有大量灰尘、震动、极端寒冷或
炎热 ( 如阳光直射、靠近加热器或烈日下的汽车里 ) 的环境中。
•请勿在设备上放乙烯或塑料或橡胶物体，否则可能使面板脱色。
•清洁设备时，使用柔软的干布。请勿使用涂料稀释剂、溶剂、清洁液或浸了化学物质的抹布。
•请勿将任何均衡器和VOL 音量设定在最大位置。否则，根据所连接设备的具体状态，可能会导致反馈而损坏音
箱。
本机内建的充电电池为铅酸蓄电池12V/7.5Ah，在出厂前是充满电状态，但由于长距离
运输或长时间库存等原因，使得电池可能会自然放完电，造成电力不足。
所以当您第一次使用前，请务必先充电 4 至 5 小时。这项动作非常重要，因为它保障了电
池接下来的使用寿命。
充电时，请将随机附赠的电源适配器 DC端插入 SE108 的 DC 输入 (DCIN) 座，另一端
接电源，此时充电LED 就会呈现红灯，当电池充满后，呈现绿色灯。
本机内建有 REVERB 混响效果，当演讲、唱歌或表演时，可适当加入，为您的人声演奏营
造出一种不同的氛围
将 CH1 通道或 CH2 通道上的「REVERB」混响开关调整至「ON」位置。当混
响开关开启时，系统会将混响效果送至您已开启的通道。
使用「REVERB」混响的「VOL」音量控制旋钮可以调节混响
效果量
1
2
轻按
一下
按住
兩秒
快速
闪烁
快速
闪烁
开启蓝牙：
如需切换蓝牙设备：
1. 轻按 BLUETOOTH「PAIRING」一下，LED 灯快速闪烁
2.开启手机或是其他设备的蓝牙 , 并进行配对和连接
3.当 LED 灯持续点亮时 , 您可以开始播放您的蓝牙设备的音乐
1.按住 BLUETOOTH「PAIRING」两秒，LED 灯快速闪烁
2.开启手机或是其他设备的蓝牙 , 并进行配对和连接
3.当 LED 灯持续点亮时 , 您可以开始播放您的蓝牙设备的音乐
脚架固定座
固定把手
可拆式背带扣
缓冲垫
充电电池安装盖
联络我们
中国地区营销和业务
旭广企业发展 ( 上海 ) 有限公司
021-69223756
support_cn@superlux.com.tw
国际营销和业务
Superlux舒伯乐台湾
+886-2-26931323
a
d
a
b
c
e
g
f
h
i
j
k
l
控制面板旋钮及功能
第一步：应用连接
电池灯号指示
故障排除
第二步：使用方式设置
街头艺人 卡拉ＯＫ 会 议，演 讲
特色 可选配件
a.CH1 / CH2 VOL
话筒和乐器输入接
口增益控制
d. REV VOL
混响音量大小控制
f.BLUETOOTH
蓝牙及音量控制
h.UHF WIRELESS
UHF 无线話筒音量
控制 ( 仅 SE108W)
k.DC IN
充电插座
l.POWER
电源开关
i.BASS
低频均衡器
TREBLE
高频均衡器
（出厂设定为置中位置）
g. HEADPHONE OUTPUT
6.3 耳机输出及输出音量控
制
e.AUX 3.5
信号输入及音量控制
c.CH1 / CH2
输入接口及 MIC/LINE 切
换开关
b.REVERB
混响切換开关
j. MASTER
总音量控制
将需要的设备 , 如话筒或乐器插入输入口
( 按照下图将各通道 VOL 音量调至最小 )
连接话筒时，请先将 MIC/LINE 开关设置到「MIC」
连接乐器时，请将 MIC/LINE 开关设置到「LINE」
将 MAINLEVELCONTROL 总音量调至最小
先打开已连接的音源（如果有），然后打开
SE108/SE108W 电源，电源 LED 灯会亮起
1
2
3
4
5
6
7
走到哪唱到哪
走到哪放到哪
SE108 克服了传统音箱固有的笨重属性，着重考虑便携
性，并融入了背包元素。
内置无线话筒（仅 SE108W），解放您的双手！同时融入
了无线蓝芽技术，可与手机等设备连结，不受线材限制。
•重量轻，着重考虑便携性，并融入了背包元素
•方 便 使 用，且 操 作 简 易
•含耳机监听输出接口
•具有 2 通道 TRS 插孔输入，及独立音量大小控制
•内置蓝牙配对功能，使用蓝牙 4.1 协议，可以更方便的输入音源
•具有 REVERB 混响效果
•具有高低频均衡器，可调整高音与低音音质
•内置 1 组 U 频无线麦克风。（仅 SE108W）
•充电电池可连续使用 5 小时以上
•TM58 手持有线动圈话筒
•HMD685aMKII 动圈式耳麦
•HM108 延伸臂架（含手机夹）
•防水音箱袋
•MS108E/BAG 话筒脚架
•无线手持麦克风 UK6（仅 SE108W）
•无线腰包话筒 UK7（仅 SE108W）
•返监听音箱 SE02
•SPS400 音箱支架
快速指南
将话筒，乐器和音频设备连接到 SE108 / SE108W
演奏乐器或是用话筒唱歌时，通过顺时针（提高音量）或逆时针（降低音量）调整
每个通道的 VOL 音量（建议将旋钮调整至 1/2 处）
通过调节 MAINLEVELCONTROL 总音量旋钮做最后的音量调整
如 果 声 音 和 音 量 听 起 来 匹 配 适 当，设 置 即 告 完 成
将电源打开时 ,Power指示燈会亮绿灯
当电池状态灯变红，这表示电池电量已弱，必须充电
UK6 UK7
使用 UK6/UK7 无线话筒时，请由
无线麦克风控制旋钮调节音量大小。
（此功能为 SE108W）
红灯 绿灯
* 如果特定的问题依旧存在，请咨询 Superlux 经销商。
电源不能打开
◆确认电池是否有足够的电量，或是是否安
全牢固地连接好了充电线？
听不到声音？
◆ POWER指示灯是否有亮起？确认电源是
否开启或是电池是否有电量。
◆是否安全牢固地连接好输入连接线 ?
◆话筒，乐器和音频设备是否功能正常？
声音失 真或 发出 噪音？
◆所 有 相 关 通 道 的ＶＯＬ音量控制旋钮和 /
或 MASTER总音量控制旋钮是否设置得
高？
◆相应通道 MIC/LINE 的开关是否设置成
MI C 了？如果来自声源的输入信号电平
较高的情况下，将 MIC/LINE 开关设置
为 MIC，可能造成失真声。请将开关设置
为 LINE 位置。
◆所连接备的音量是否太高？降低外接设备
的输出音量。
声音不够响？
◆所 有 相 关 通 道 的ＶＯＬ音量 控 制 旋 钮
和 / 或 MASTERＶＯＬ音量控制旋钮
是 否 设 置得 太 低？
◆相应通道的 MIC/LINE 开关是否设
置成了 LINE ？将ＶＯＬ音量 旋 钮调 整
到最小（零）。将开关设定到 MIC 位置，
然后慢慢提升ＶＯＬ音量旋钮。
◆所连接设备的音量是否太低？提高外
接设备的输出音量。
高音声音和低音声音不平衡
◆是不是均衡器提升或降低得太多了？
将均衡器设置到中心位置（原厂设定
已设置于中心位置）
电池损坏
◆ 若 电 池 太 久 无 使 用，或 其 他 原 因 造 成
损坏，可将喇叭背部的电池安装盖打
开，更换上新的铅酸电池（12v7.5Ah）
即可（在安装时请注意正负极接点 )
PORTABLE
ENTERTAINMENT
SYSTEM
SE108
SE108W
USER MANUAL
www.superlux.com.tw
• Driver:
LF: 8" / HF: 1" compression driver
• LF Power Amp:
40W
• Frequency Response(-10dB):
55-20kHz
• Input Sensitivity:
Mic: -38dBu / Line: 0dBu
• Max. Peak SPL:
110 dB SPL
• Crossover:
4k Hz
• Input :
6.3mm LINE IN & MIC, 3.5mm AUX IN
• Impedance:
MIC=1.65K / LINE=22.5K
• Enclosure Material:
PP
• Output:
Headphone out
• RMS Output Power:
40W/4Ω (@THD<1% at
1KHz)
• Total Harmonic Distortion:
≤0.3% @20-
20,000Hz, +14 dBu
• Charging Requirement:
12V / 7.5AH
(Charger included)
• Dimensions (HxWxD):
441 x 330 x 262mm
• NET Weight:
10KG
Recharge the battery Bluetooth wireless connection
Attaching a speaker
to a speaker stand.
Notice
Maintenance
Specications
PRECAUTIONS
Exterior
Applying Reverb
Please recharge the battery for 4 to 5 hours
before rst use.
To pair a Bluetooth wireless technology device with SE108/SE108W, follow these
steps
!
PLEASE READ CAREFULLY BEFORE PROCEEDING
*Please keep this manual in a safe place for future
reference
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even
death from electrical shock, short-circuiting, damages, re or other hazards. These precautions
include, but are not limited to, the following:
HANDLING CAUTION
• Do not insert your ngers or hands in any gaps or openings on the vents or panel of the mixer
and the ports of the speaker.
• Avoud inserting or dropping foreign objects ( paper, plastic, metal, etc.) into any gaps or
openings on the vents or panel of the mixer and the ports of the speaker. If this happens, turn
off the power immediately.
• Do not rest your weight on the device or place heavy objects on it, and avoid use excessive
force on the buttons, switches or connectors.
• Do not use the speakers for a long period of time at a hiht or uncomfortable volume level,
since this can cause permanent hearing loss. If you experience any hearing loss or ringing in
the ears, consult a physician.
• Do not operate the device if the sound is distorting. Prolonged use in this condition could
cause overheating and result in re.
• Do not pull on any attached cable, such that of a microphone. Doing so may cause the
speaker to topple, and result in damage or in injury.
Power supply / Power cord
• Do not place the power cord near heat sources such
as heaters or radiators, and do not excessively bend
or otherwise damage the cord, place heavy objects
on it, or placeit in a position where anyone could
walk on, trip over, or roll anything over it.
• Use only the supplied power cord.
• Check the electric plug periodically and remove any
dirt or dust which may have accumulated on it.
Do not open
• This device contains no user-serviceable parts.
Do not open the device attempt to disassemble
the internal parts or modify them in any way. If it
should appear to be malfunctioning, discontinue
use immediately and have it inspected by qualied
Superlux service personnel.
Water warning
• Do not expose the device to rain, use it near
water or in damp or wet conditions, or place on it
any containers ( such as vases, bottles or glasses)
containing liquids which might spill into any openings.
If any liquid such as water seeps into the device, turn
off the power immediately and unplug the power cord
from the AC outlet. Then have the device inspected by
qualied Supelrux service personnel.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not put burning items, such as candles, on the unit.
A burning item may fall over ad cause a re.
If you notice any abnormality
• When one of the following problems occur, immediately
turn off the power switch and disconnect the electric
plug from the outlet. Then have the device inspected by
Superlux service personnel.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the
device.
Handling and Maintenance
• Do not expose the device to excessive dust or vibration, or extreme cold or heat ( such as in direct sunlight, near
a heater, or in a car during the day) , in order to prevent the possibility of panel disguration, unstable operation,
or damage to the internal components.
• Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning uids, or
chemical- impregnated wiping cloths.
• Avoid setting all equalizer controls and LEVEL knobs to their maximum. Depending on the condition of the
connected devices, doing so may cause feedback and may damage the speakers.
Please recharge the battery before rst use. The built-in lead-acid battery is
12V/7.5Ah, please recharge the battery for 4 to 5 hours before rst use.
Tough the battery will be fully charged before leaving the factory, the battery might be
discharged due to the long distance transportation or the long storing time to cause
the low level of the battery. Please recharge the battery to full level before rst use in
order to have the longer uselife of the battery.
When recharge, please connect the DC jack of the furnished adaptor to the DC IN
socket of the SE108 speaker, and connect the AC jack of the adaptor to the AC socket
of the SE108 speaker.
The red LED lights up when charging and turn to green light when fully charged.
SE108/SE108W features a built-in reverb processor. Applying reverb processor can
add a different atmosphere for your vocals
Switch the Reverb switch to “ON” position. Then the Reverb effect can be
applied onto the indicated channel.
UsetheREVERBcontroltoadjustthethelevelofthe
reverbtothecorrespondingchannel.
1
2
PRESS
PRESS
2 S
LED
FLASHES
QUICKLY
LED
FLASHES
QUICKLY
When turn on
Bluetooth:
When need to
change Bluetooth
devices:
1. Press the BLUETOOTH PAIRING button, the LED ashes quickly.
2. Active Bluetooth Wireless function in your mobile phone or other devices for pairing and
connection.
3. When the LED lights up continuously, you can start to playing music from your Bluetooth
wireless device.
1. Press the BLUETOOTH PAIRING button for around 2 seconds, then the LED ashes quickly.
2. Active Bluetooth Wireless function in your mobile phone or other devices for pairing and
connection.
3. When the LED lights up continuously, you can start to play music from your Bluetooth wireless
device.
Stand holder
Handle
Removeable Strap
Buckle
Cushion
Rechargeable
Battery Installation
Cover
Contact us
Marketing and sales
Superlux Taiwan
+886-2-26931323
sales@superlux.com.tw
support@superlux.com.tw
Manufacturing & logistics
Superlux Enterprise
Development (Shanghai) Co., Ltd
To avoid the possibility of malfunction or damage to the product,
follow the notices below.
Remove the power plug from the AC outlet when
cleaning the device
a
d
a
b
c
e
g
f
h
i
j
k
l
Control panel knobs and functions
Step 2: Settings
Features Optional Accessories
Step 1: Applications
Troubleshooting
Busker KARAOKE Meeting, lecture
l.Power switch
b. Reverb
Reverberate switch
j
.Master
Master
volume
control
a.CH1 / CH2 VOL
microphone and
instrument input VOL
controls.
c.CH1 / CH2
MIC / LINE input jacks
and MIC / LINE switches
e.AUX
3.5 Audio input and
volume control
g.Headphone Output
6.3 Headphone output
and output volume
control
i.BASS
Hidden EQ funtion
(default setting as middle) /
TREBLE
Hidden EQ funtion
(default setting as middle)
d.REV VOL
Reverb Volume control
f.Bluetooth
Bluetooth Pairing and
Volume Control
h. UHF Wireless UHF
Wireless Microphone
Volume Control
(SE108W only)
k.DC IN
charging port
Connect the microphone or instrument to the input jack ( turn each channel to the
minimized level or closed as shown in the following gure)
When connect to the
MIC
please turn [Mic/Line] switch to
MIC.
When connect to the
instrument
please turn [Mic/Line] switch to
LINE.
Set the Main Level Control knob to the minimum level
Turn on the music player rst (if the music input is
needed during use) and turn on the SE108 / SE108W
power supply LED will light up
1
2
3
4
5
6
7
MUSIC ON THE
GO….ANYWHERE
• Light-weighted and easy portability. Backpack aesthetic design.
• Easy to use and operate.
• With headphone monitor output jack.
• With two TRS jack inputs and separate volume control
• Bulit-in Bluetooth function. Bluetooth 4.1 technology for more
convenient music input connection.
• With REVERB function
• The two-stage hidden EQ can adjust the treble and bass sound
quality perfectly.
• Furnished with a U channel wireless microphone (only SE108W
version)
• Battery use for more than 5 hours
1. TM58 handheld wired dynamic microphone
2. HMD685aMKII headset with incorporated dynamic microphone
3. HM108 extension boom arm (with phone clip)
4. Waterproof bag for speaker
5. MS108E/BAG microphone stand
6. Handheld Wireless Microphones UK6 (only SE108W version)
7. Headworn Microphones UK7 (only SE108W version)
8. Monitor Speakers SE02
9. SPS400 Speaker stand
QUICK GUIDE
Connect the microphone, instrument and audio equipment to the SE108 / SE108W
When playing the musical instrument or using the microphone, adjust the level of
each channel by turning the volume knob
clockwise (increase the volume) or
counterclockwise (decreasing the volume)
Adjust the Main Level Control for the nal volume adjustment if the sound
and volume sound are feeling match then the setting is completed
When turning on the power, the LED light will turn
green.
When the battery light turn
red
please
recharge the battery.
It is able to use and recharge the SE108 at the same time.
UK6 UK7
When using the UK6 / UK7 wireless
microphone, adjust the volume level by
the wireless microphone control knob
(this function only for SE108W)
*If any specic problem should persist, please contact with Supelrux dealer.
Cannot be turned on.
◆
Please check if there is enough power in
the battery. Is the power cord connected
safely and rmly?
No sound
◆
Does the Power LED light up? Check
whether the power is turned on or the power
is enough in the battery.
◆
Is the power cord connected safely and rmly?
◆
Please check all the audio devices are
functional well.
Battery light
indication
Battery low >> Red lightPower on >> Green light
SE108 overcomes the bulky characteristic of the traditional
speakers and provides ultra portability.The backpack element
of SE108 fully reects its personality and the design concepts.
The built-in wireless microphone system and Bluetooth
technology will free your hands and provide easy connection
with any devices without constraints of cables.
Sound is distorted or noise is
produced
Sound is not loud enough
The treble/bass level is not
balanced.
Battery Damage
◆
Are the LEVEL controls of all relevant
channels and / or the MASTER LEVEL
control set too high?
◆
Is the MIC / LINE switch of the
corresponding channel set to MIC?
If the input level of the source is high,
setting the MIC/LINE switch to MIC may
result in distorted sound. Set the switch to
LINE position in this case.
◆
Is the volume setting of the connected
device too high? Lower the volume output
setting of the external device.
◆
Are the equalizer controls raised or
lowered too much? Set the equalizer
controls to the center position. (default
at the middle)
If the unused of the battery or the other
reason to cause the battery damge, please
open the battery box at the back of the
speaker cabinet to replace a new lead-acid
battery (12V, 7.5Ah).
Please note the position of the positive and
negative contact when replace the battery.
◆
Are the LEVEL controls of all relevant
channels and / or the MASTER
LEVEL control set too low?
◆
Is the MIC /LINE switch of the
corresponding channel set to LINE?
Turn the LEVEL control to the
minimum (zero). Set the switch to
the MIC position. Then slowly raise
the LEVEL control.
◆
Is the volume setting of the
connected device too low? Raise the
volume output setting of the external
device.
-
1
-
2
-
3
-
4
