Bitspower BPTA-DSWDP-O11DE インストールガイド

ブランド: Bitspower

モデル: BPTA-DSWDP-O11DE

タイプ: インストールガイド

主件說明/Accessories/主件说明

Sedna O11D for LIAN LI O11 DYNAMIC

注意，跑水前，請先確認所有零件已安裝在正確的位置上，在不開主機，單開水泵的情况下，進行24小時的跑水測試，確保無漏水情况後再開主機，避免發生漏水而導致電腦零件的損壞。

注意，跑水前，请先确认所有零件已安装在正确的位置上，在不开主机，单开水泵的情况下，进行24小时的跑水测试，确保无漏水情况后再开主机，避免发生漏水而导致电脑零件的损坏。

Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test

with only the pump connected to the power supply .

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。

本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。

Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.

BPTA-DSWDP-O11DE

六角板手(2.5毫米)

Hex wrench (2.5MM)

六角板手(2.5毫米)

M4x6毫米螺絲

M4x6mm Screw

M4x6毫米螺丝

洩水接頭

BP-ETW

泄水接头

排氣接頭

BP-ETAIR

排气接头

大4PIN供電線材

3PIN/4PIN transfer 4PIN

大4PIN供电线材

水箱與水泵不可拆解！一經拆解即不保固。

The water tank and pump can’t be disassembled! Once

disassembled, there is no guarantee.

水箱与水泵不可拆解！一经拆解即不保固。

S1水泵規格

電源電壓：12V DC

輸入功率：≤17W

電氣連接器：Molex 4 Pin

噪音：40~45dBA

最大轉速：-

S1 Pump Spec.

Power/Voltage：12V DC

DC power：≤17W

Electric Connector：Molex

4 Pin

Noise：40~45dBA

Maximum Revolution：-

S1水泵规格

电源电压：12V DC

输入功率：≤17W

电气连接器：Molex 4 Pin

噪音：40~45dBA

最大转速：-

S1馬達除了可由主機板供電外，亦可

透過轉接線由電源供應器直接供電。

Except the motherboard, S1 pump

can be powered from the power

supply via a patch cord.

S1水泵除了可由主机板供电外，亦可

透过转接线由电源供应器直接供电。

供電與馬達/Power Supply and Pump/供电与马达

Sedna O11D for LIAN LI O11 DYNAMIC

Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test

with only the pump connected to the power supply .

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。

本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。

Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.

BP-ETAIR

建議將排氣接頭安裝於

水箱且在水位之上。

It is recommended to

install the air-exhaust

fitting on the reservoir,

above the water line.

建议将排气接头安装于

水箱且在水位之上。

Step 1

將按鈕按下即可排氣。

Press the button to

release the air.

将按钮按下即可排气。

BP-ETW

建議將洩水接頭安裝於

水冷系統的最低點。

It is recommended to install the water-exhaust

fitting at the lowest point of the water cooling

system.

建议将泄水接头安装于水冷系统的最低点。

Step 1

將洩水接頭上蓋旋起。

Unscrew the top of the water-exhaust fitting.

将泄水接头上盖旋起。

Step 2

換上洩水配件，旋入配件過程中即會逐漸洩

水，建議外接管線以利洩水。

Replace with the water-exhaust part. When

screwing in the part, water will start to

discharge, it is recommended to connect

tubing beforehand to control the water outflow.

换上泄水配件，旋入配件过程中即会逐渐泄

水，建议外接管线以利泄水。

安裝方式/Installation/安装方式安裝方式/Installation/安装方式

BP-ETAIR BP-ETW

A 電源負極 -

B 電源正極 +

A Negative electrode -

B positive electrode +

A 电源负极 -

B 电源正极 +

A B

注水/Water/注水

Sedna O11D for LIAN LI O11 DYNAMIC

Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test

with only the pump connected to the power supply .

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。

本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。

Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.

注意：Bitspower建議消費者使用蒸餾水、純凈水，加入Bitspower的染劑作為水冷液使用；如客戶自行選購的水冷液導致電鍍層剝落、

水道堵塞、水泵轉動不正常、水箱管破裂或密封圈變型以致漏水等及其它不可抗力之問題時，消費者自行承擔相關產品責任。

未注水前，請勿啟動水泵電源。

注意：Bitspower 建议消费者使用蒸馏水、纯净水，加入Bitspower的染剂作为水冷液使用；如客户自行选购的水冷液导致电镀层剥落、

水道堵塞、水泵转动不正常、水箱管破裂或密封圈变型以致漏水等及其它不可抗力之问题时，消费者自行承担相关产品责任。

未注水前，请勿启动水泵电源。

Notice:

Bitspower recommends that consumers add the Bitspower dye to distilled water or purified water for their water-cooling

liquid. If the consumer chooses different water-cooling liquids, the resulting impurities may cause peeling of the coating

on some of the hardware, water channels blockage by built-up residue, improper operation of the water pump, water

tank tube breakage, and o-rings deformation leading to leakage. Any issues related to the use of inappropriate

water-cooling liquid will be the responsibility of the consumer.

Do not turn on the pump if the reservoir is empty.

-------產品保修規範------

質保期時效，送修的產品凡有以下狀況，不在保修

範圍內。

【CPU水冷頭】

1.冷頭自體螺絲，有拆裝痕跡，整套產品失保。

2.頂部的進出口，因為外力使用不當導致開裂。

【冷排】

1.因為外力使用不當導致冷排水道破裂漏水。

2.進出水孔因為外力使用不當導致開裂。

【接頭】

1.有器械夾持導致的損傷痕跡。

【水泵】

1.無水通電導致水泵燒毀。

2.底部pcb進水燒毀。

3.水箱底座與水泵不可拆解，一經拆解即不保固。

【風扇】

1.進水燒毀。

---Product Warranty Rules---

The warranty will be void if any of the situations below

happen.

【

CPU Water Block

】

- The CPU block and the screws in it has any trace of disassemble.

- The top plate inlet and outlet ports, due to improper use of

external forces, are cracked.

【

Radiator

】

- The fin of the radiator are broken or deformed due to improper

use of external forces.

- The inlet and outlet of the radiator are cracked due to improper

use of external forces.

【

Fitting

】

- There are signs of damage caused by instrument clamping on the

fittings.

【

PUMP

】

- Pump damage from pump operation without any liquid.

- Pump damage caused by water leak on the pump's PCB.

- Water tank has been separated from the pump.

【

Fan

】

- Fan damaged by water leak.

-------产品保修规范------

质保期时效，送修的产品凡有以下状况，不在保修

范围内。

【CPU水冷头】

1.冷头自体螺丝，有拆装痕迹，整套产品失保。

2.顶部的进出口，因为外力使用不当导致开裂。

【冷排】

1.因为外力使用不当导致冷排水道破裂漏水。

2.进出水孔因为外力使用不当导致开裂。

【接头】

1.有器械夹持导致的损伤痕迹。

【水泵】

1.无水通电导致水泵烧毁。

2.底部pcb进水烧毁。

3.水箱底座与水泵不可拆解，一经拆解即不保固。

【风扇】

1.进水烧毁。

選擇喜好的水冷濃縮液顏色，以純淨水調合，由”填水孔”注入至水箱九分滿，接著利用”24PIN跳

線開關”啟動電源，讓水路中的空氣集中至水箱排出，再依水量繼續添加至水箱九分滿左右即可。

（24PIN跳線開關用途：需無經主板開啟ATX電源時，使電源直接開啟供電。）

Choose your desired dye color and mix it with pure distilled water. Pour the water mix into the reservoir

via the water filling hole. Once the reservoir is 90% full, turn on the power supply for the pump to run

and let the air exit the loop. Turn off the power supply when the reservoir is near empty. Repeat until all

the air has exited the loop. (In order to power the pump only, connect the power switch connector to

the 24 pin cable of the power supply. This will allow the power supply to bypass the motherboard and

make the pump work alone.)

选择喜好的水冷浓缩液颜色，以纯净水调合，由”填水孔”注入至水箱九分满，接着利用”24PIN跳

线开关”启动电源，让水路中的空气集中至水箱排出，再依水量继续添加至水箱九分满左右即可。

（24PIN跳线开关用途：需无经主板开启ATX电源时，使电源直接开启供电。）

安裝方式/Installation/安装方式

Sedna O11D for LIAN LI O11 DYNAMIC

Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test

with only the pump connected to the power supply .

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。

本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。

Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.

BPTA-DSWDP-O11DE

M4x6 螺絲

M4x6 Screw

M4x6 螺丝

頂蓋

TOP

顶盖

側板

Side plate

侧板

前面板

Front plate

前面板

玻璃板

Glass plate

玻璃板

防塵罩

Dust shield

防尘罩

PC-O11 Dynamic

(不包括/Not included /不包括)

步驟1/Step 1/步骤1 步驟2/Step 2/步骤2

步驟3/Step 3/步骤3 步驟4/Step 4/步骤4

產品介紹/Product Presentation/产品介绍

CPU水冷頭(不包括)

CPU water block(Not Included)

CPU水冷头(不包括)

VGA水冷頭(不包括)

VGA water block(Not Included)

VGA水冷头(不包括)

冷排(不包括)

Radiators(Not Included)

冷排(不包括)

BP-ETAIR

BP-ETW

BPTA-DSWDP-O11DE

建議安裝方式

Recommended installation method

建议安装方式

Sedna O11D for LIAN LI O11 DYNAMIC

V7/第七版

Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test

with only the pump connected to the power supply .

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。

本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。

Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.

BPTA-DSWDP-O11DE 產品內容物請參閱「主件說明」，未列出之零件與配件不含在產品包裝內。

See 「Accessories」 for a list of included parts with the BPTA-DSWDP-O11DE, other accessories are sold separately.

BPTA-DSWDP-O11DE 产品内容物请参阅「主件说明」，未列出之零件与配件不含在产品包装内。