MAIN PARAMETERS
• GAIN: adjusts the Tone Model’s gain
• BASS: adjusts the level of low frequencies (shelf)
• MID: adjusts the level of mid frequencies (bell)
• TREBLE: adjusts the level of high frequencies (shelf)
• VOLUME: adjusts TONEX Pedal’s master volume.
ALTERNATIVE PARAMETERS
• REVERB: adjusts the reverb’s mix
• COMPRESSOR: adjusts the compressor’s threshold (with auto make up gain)
• NOISE-GATE: adjusts the noise-gate’s threshold
• PRESENCE: adjusts the Tone Model’s high-frequency content
• DEPTH: adjusts the Tone Model’s low-frequency content
ADVANCED PARAMETERS
• MODEL.VOL: adjusts the AMP MODEL volume.
• NOISE-GATE: enables/disables the noise-gate
• NOISE-GATE RELEASE: adjusts the noise-gate’s release
• NOISE-GATE DEPTH: adjusts the noise-gate’s depth
• COMPRESSOR: enables/disables the compressor
• COMPRESSOR GAIN: adjusts the compressor’s make-up gain
• COMPRESSOR ATTACK: adjusts the compressor’s attack
• COMPRESSOR PATCH: sets the compressor to be pre/post Tone Model
• BASS FREQUENCY: adjusts the bass-band frequency
• MID Q: adjusts the mid-band Q factor
• MID FREQUENCY: adjusts the mid-band frequency
• TREBLE FREQUENCY: adjusts the high-band frequency
• EQ PATCH: sets the EQ to be pre/post Tone Model
• MIX: adjusts the Tone Model’s mix
• REVERB: enables/disables the reverb
• REVERB MODE: sets the reverb algorithm
• TIME: adjusts the reverb’s decay tail
• PRE-DELAY: adjusts the reverb’s pre-delay
• COLOR: adjusts the reverb’s frequency balance
The following parameters are available if a VIR cabinet is selected:
• RESO: adjusts the VIR cab resonance
• MIC 1: sets the mic 1 model
• MIC 1 X: adjusts the mic 1 position on the speaker
• MIC 1 Z: adjusts the mic 1 distance from the speaker
• MIC 2: sets the mic 2 model
• MIC 2 X: adjusts the mic 2 position on the speaker
• MIC 2 Z: adjusts the mic 2 distance from the speaker
• MICS MIX: adjust the two microphones’ balance (-100%: mic 1, +100%: mic 2)
The UNDERLINED parameters are available in ADVANCED USERMODE selectable in the GLOBAL SETUP.
PRESET SETUP
• EXT. CTRL: enables/disables the external pedal
• EXT.LEARN: sets/removes a parameter’s assignment to the control pedal
• AMP: enables/bypasses the Tone Model’s amp
• CAB: enables/bypasses the Tone Model’s cab
GLOBAL SETUP
• NAMING: sets the display’s visualization of preset names
o Only Name
o Program Change number and name
o Bank number and name
• BANK NAV: enables/disables the bank navigation with footswitches
o ON: press A+B to move a bank down, press B+C to move a bank up. Footswitches work at
release.
o OFF: footswitches work at push. Bank up and down can still be performed with an external
double switch pedal.
• CAB: enables/disables the cabinet globally on all presets
• USERMODE: sets the user mode for the pedal
o EASY: reduced parameter list for easier browsing
o ADVANCED: full parameter list for better tone control
• EXT. CTRL: sets the type of external control
o TRS expression pedal
o RTS expression pedal
o Normally Open single switch pedal
o Normally Closed single switch pedal
o Normally Open double switch pedal
o Normally Closed double switch pedal
• DUAL SWITCH MODE: sets the external control pedal functionality
o PRESET: use the double switch pedal to move preset up or preset down
o BANK: use the double switch pedal to move bank up or bank down
• EXP.CALIB: calibrates an expression pedal for flawless operation
• MIDI CH: sets the MIDI channel on which the pedal operates
• MIDI.THRU: sets the preferred MIDI functionality
o OFF: no MIDI signals are sent to TONEX’s MIDI outputs
o THROUGH: MIDI signals arriving to the TONEX’s MIDI inputs are sent to TONEX’s MIDI
outputs
o MERGE: MIDI arriving to the TONEX MIDI inputs, and the MIDI signals generated by TONEX
itself are merged and sent to the TONEX’s MIDI outputs
• TRIM IN: adjusts the input level of your instrument
• MAIN VOL: adjusts TONEX’s analog master volume, both dry and wet
• INTERFACE VOL: adjusts TONEX’s interface master volume
• OPERATION MODE: sets TONEX’s operative mode
o LIVE: the most common way to use the pedal in live situations
o INTERFACE: when using the pedal in interface mode the audio is recorded and monitored
using the computer
• USB OUT: sets the USB OUT routing
o STEREO: the stereo processed signal is routed to USB OUT 1 and 2
o DUAL: the left processed signal is routed to USB OUT 1, the DI dry signal is routed to USB
OUT 2
• INFO: displays the firmware version installed
• FACTORY: performs a factory reset to all the global settings, presets are left untouched
