Biostar TB350-BTC ユーザーマニュアル

FCC Informaon and Copyright

This equipment has been tested and found to comply with the limits of a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon

against harmful interference in a residenal installaon. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instrucons,

may cause harmful interference to radio communicaons. There is no guarantee that interference

will not occur in a parcular installaon.

The vendor makes no representaons or warranes with respect to the contents here and

specially disclaims any implied warranes of merchantability or tness for any purpose. Further

the vendor reserves the right to revise this publicaon and to make changes to the contents here

without obligaon to nofy any party beforehand.

Duplicaon of this publicaon, in part or in whole, is not allowed without rst obtaining the

vendor’s approval in wring.

The content of this user’s manual is subject to be changed without noce and we will not be

responsible for any mistakes found in this user’s manual. All the brand and product names are

trademarks of their respecve companies.

Dichiarazione di conformità sinteca

Ai sensi dell’art. 2 comma 3 del D.M. 275 del

30/10/2002

Si dichiara che questo prodoo è conforme

alle normave vigen e soddisfa i requisi

essenziali richies dalle direve

2004/108/CE, 2006/95/CE e 1999/05/CE

quando ad esso applicabili

Short Declaraon of conformity

We declare this product is complying with the

laws in force and meeng all the essenal

requirements as specied by the direcves

2004/108/CE, 2006/95/CE and 1999/05/CE

whenever these laws may be applied

2 | Table Of Contents

Table Of Contents

FCC Informaon and Copyright �� 1

Chapter 1: Introducon �� 3

1.1 Before You Start .................................................................................................................. 3

1.2 Package Checklist ................................................................................................................ 3

1.3 Specicaons ...................................................................................................................... 4

1.4 Rear Panel Connectors ........................................................................................................ 5

1.5 Motherboard Layout .......................................................................................................... 6

Chapter 2: Hardware installaon �� 7

2.1 Install Central Processing Unit (CPU) .................................................................................. 7

2.2 Install a Heatsink ................................................................................................................. 8

2.3 Connect Cooling Fans ....................................................................................................... 10

2.4 Install System Memory ..................................................................................................... 10

2.5 Expansion Slots ................................................................................................................. 12

2.6 Jumper & Switch Seng ................................................................................................... 13

2.7 Headers & Connectors ...................................................................................................... 14

Chapter 3: UEFI BIOS & Soware �� 18

3.1 UEFI BIOS Setup ................................................................................................................ 18

3.2 BIOS Update ...................................................................................................................... 18

3.3 Soware ............................................................................................................................ 22

Chapter 4: Useful help�� 25

4.1 Driver Installaon ............................................................................................................. 25

4.2 AMI BIOS Beep Code......................................................................................................... 26

4.3 Troubleshoong ................................................................................................................ 26

4.4 RAID Funcons .................................................................................................................. 27

APPENDIX I: Specicaons in Other Languages �� 29

Arabic ...................................................................................................................................... 29

German ................................................................................................................................... 30

Russian .................................................................................................................................... 31

Spanish ................................................................................................................................... 32

Thai ......................................................................................................................................... 33

Chapter 1: Introducon | 3

TB350-BTC & TA320-BTC

Chapter 1: Introducon

1�1 Before You Start

Thank you for choosing our product. Before you start installing the motherboard, please make

sure you follow the instrucons below:

• Prepare a dry and stable working environment with sucient lighng.

• Always disconnect the computer from power outlet before operaon.

• Before you take the motherboard out from an-stac bag, ground yourself properly

by touching any safely grounded appliance, or use grounded wrist strap to remove the

stac charge.

• Avoid touching the components on motherboard or the rear side of the board unless

necessary. Hold the board on the edge, do not try to bend or ex the board.

• Do not leave any unfastened small parts inside the case aer installaon. Loose parts

will cause short circuits which may damage the equipment.

• Keep the computer from dangerous area, such as heat source, humid air and water.

• The operang temperatures of the computer should be 0 to 45 degrees Celsius.

• To avoid injury, be careful of:

Sharp pins on headers and connectors

Rough edges and sharp corners on the chassis

Damage to wires that could cause a short circuit

1.2 Package Checklist

• Serial ATA Cable x2

• Rear I/O Panel for ATX Case x1

• User’s Manual x1

• Fully Setup Driver DVD x1

Note

»

 Thepackagecontentsmaybedierentduetothesalesregionormodelsinwhichitwassold.For

moreinformaonaboutthestandardpackageinyourregion,pleasecontactyourdealerorsales

representave.

4 | Chapter 1: Introducon

1�3 Specifications

Specicaons

CPU Support

Socket AM4 supports AMD A-series APU / CPU

Maximum CPU TDP (Thermal Design Power): 95Wa

* Please refer to www.biostar.com.tw for CPU support list.

Chipset

AMD B350 (TB350-BTC)

AMD A320 (TA320-BTC)

Memory

Supports Dual Channel DDR4 1866/2133/2400/2667

2 x DDR4 DIMM Memory Slot, Max. Supports up to 32 GB Memory

Each DIMM supports non-ECC & ECC 4/8/16 GB DDR4 module

* DDR4 - 2667 only for Ryzen CPU.

* Please refer to www.biostar.com.tw for Memory support list.

Storage 4x SATA III Connector (6Gb/s) : Supports AHCI & RAID 0, 1, 10

LAN

Realtek RTL 8111H

10/ 100/ 1000 Mb/s auto negoaon, Half / Full duplex capability

Audio Codec

ALC887

7.1 Channels, High Denion Audio

USB

6x USB 3.1 Gen1 (5Gb/s) port (4 on rear I/Os and 2 via internal headers)

6x USB 2.0 port (2 on rear I/Os and 4 via internal headers)

Expansion Slots

3x PCIe 2.0 x1 Slot

2x PCIe 3.0 x1 Slot (for Bitcoin mining, please change the speed to PCI-E 1.0 in BIOS seng)

1x PCIe 3.0 x16 Slot : When using APU or NPU, the bandwidth is x8 speed

Rear I/Os

1x PS/2 Mouse

1x PS/2 Keyboard

1x DVI-D Port

1x LAN port

4x USB 3.1 Gen1 (5Gb/s) Port

2x USB 2.0 Port (only 5V power)

2x USB 2.0 Port

3x Audio Jack

Internal I/Os

4x SATA III 6.0Gb/s Connector

2x USB 2.0 Header (each header supports 2 USB 2.0 ports)

1x USB 3.1 Gen1 (5Gb/s) Header (each header supports 2 USB 3.1 Gen1 ports)

1x 8-Pin Power Connector

1x 24-Pin Power Connector

2x 4-Pin Power Connector (for Bitcoin mining, 4pin power connector Must be Installed)

1x 15-Pin SATA Power Connector (for USB power enhancement)

1x CPU Fan Connector

1x System Fan Connector

1x Front Panel Header

1x Front Audio Header

1x COM Serial Header

1x Clear CMOS Header

Form Factor ATX Form Factor, 295 mm x 210 mm

OS Support

Windows 7(64bit) / 10(64bit)

Biostar reserves the right to add or remove support for any OS with or without noce.

Chapter 1: Introducon | 5

TB350-BTC & TA320-BTC

1.4 Rear Panel Connectors

Note



»

DVI-DoutputrequireanAMDfamilyprocessorwithintedratedgraphics.



»

SincetheaudiochipsupportsHighDenionAudioSpecicaon,thefunconofeachaudiojack

canbedenedbysoware.Theinput/outputfunconofeachaudiojacklistedaboverepresents

thedefaultseng.However,whenconnecngexternalmicrophonetotheaudioport,pleaseuse

theLineIn(Blue)andMicIn(Pink)audiojack.



»

Maximumresoluon

DVI-D:1920x1200@60Hz



»

WhenusingthefrontHDaudiojackandplugintheheadset/microphone,therearsoundwillbe

automacallyDisabled.

6 | Chapter 1: Introducon

1.5 Motherboard Layout

Note

»



representsthe1stpin.

Chapter 2: Hardware installaon | 7

TB350-BTC & TA320-BTC

Chapter 2: Hardware installaon

2.1 Install Central Processing Unit (CPU)

Step 1: Locate the CPU socket on the motherboard

Step 2: Pull the socket locking out from the socket and then raise the lever up to a 90-degree

angel.

Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point

towards this white triangle. The CPU will t only in the correct orientaon.

8 | Chapter 2: Hardware installaon

Step 4: Hold the CPU down rmly, and then close the lever to locked the posion

Note

»

 PleaseturnothePowerSupplybeforeremovetheCPUsocket.

2.2 Install a Heatsink

<TypeA>

Step 1: Place the heatsink and fan assembly onto the retenon frame. Match the heatsink clip

with the socket mounng-lug. Hook the spring clip to the mounng-lug.

Step 2: On the other side, push the retenon clip straight down to lock into the plasc lug on

the retenon frame, and then press down the locker unl it stops.

Chapter 2: Hardware installaon | 9

TB350-BTC & TA320-BTC

<TypeB>

Step 1: Remove the heatsink and fan assembly bracket on the motherboard and keep the

cooler backplane under the motherboard.

Step 2: Place the heatsink and fan assembly on top of the installed CPU and make sure that the

fan cable is closest to the CPU fan connector. Please refer diagram to the following screw into

the screw hole in the order shown.

Note



»

DonotforgettoconnecttheCPUfanconnector.



»

Forproperinstallaon,pleasekindlyrefertotheinstallaonmanualofyourCPUheatsink.

10 | Chapter 2: Hardware installaon

2.3 Connect Cooling Fans

These fan headers support cooling-fans built in the computer. The fan cable and connector

may be dierent according to the fan manufacturer.

CPU_FAN1: CPU Fan Header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

4 Smart Fan Control (By Fan)

SYS_FAN1: System Fan Header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

4 Smart Fan Control (By Fan)

Note

»

 CPU_FAN1,SYS_FAN1support4-pinand3-pinheadconnectors.Whenconnecngwithwiresonto

connectors,pleasenotethattheredwireistheposiveandshouldbeconnectedtopin#2,andthe

blackwireisGroundandshouldbeconnectedtopin#1(GND).

2.4 Install System Memory

DDR4 Modules

Chapter 2: Hardware installaon | 11

TB350-BTC & TA320-BTC

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot

such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vercally and rmly into the slot unl the retaining clips snap back in

place and the DIMM is properly seated.

Note

»

 IftheDIMMdoesnotgoinsmoothly,donotforceit.Pullitallthewayoutandtryagain.

Memory Capacity

DIMM Socket Locaon DDR4 Module Total Memory Size

DIMMA1 4GB/8GB/16GB

Max is 32GB.

DIMMB1 4GB/8GB/16GB

Dual Channel Memory Installaon

Please refer to the following requirements to acvate Dual Channel funcon:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DIMMA1 DIMMB1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

Note

»

 Wheninstallingmorethanonememorymodule,werecommendtousethesamebrandand

capacitymemoryonthismotherboard.

12 | Chapter 2: Hardware installaon

Ryzen - DDR Maximum Frequency Support Table

Maximum DIMMA1 DIMMB1

DDR4-2667 SR --

DDR4-2667 DR --

DDR4-2667 SR SR

DDR4-2400 DR DR

Note

»

 SR-Single-rankDIMM,1Rx4or1Rx8.



»

DR-Dual-rankDIMMs,2Rx4or2Rx8.



»

ForthebeerDDR4modulecompability,pleasefollowthetabletoinstallyourDDR4modules.

2.5 Expansion Slots

PEX16_1: PCI-Express Gen3 x16 Slot (APU / NPU @x8 speed, Ryzen @x16 speed)

• PCI-Express 3.0 compliant.

• Theorecal maximum bandwidth using two slots simultaneously is 16GB/s for each slot,

a total of 32GB/s.

PEX1_1/1_2: PCI-Express Gen3 x1 Slot

• PCI-Express 3.0 compliant.

• Data transfer bandwidth up to 1GB/s per direcon; 2GB/s in total.

PEX1_3/1_4/1_5: PCI-Express Gen2 x1 Slot

• PCI-Express 2.0 compliant.

• Data transfer bandwidth up to 500MB/s per direcon; 1GB/s in total.

Install an Expansion Card

You can install your expansion card by following steps:

• Read the related expansion card’s instrucon document before install the expansion

card into the computer.

• Remove your computer’s chassis cover, screws and slot bracket from the computer.

• Place a card in the expansion slot and press down on the card unl it is completely

seated in the slot.

• Secure the card’s metal bracket to the chassis back panel with a screw.

• Replace your computer’s chassis cover.

• Power on the computer, if necessary, change BIOS sengs for the expansion card.

• Install related driver for the expansion card.

Chapter 2: Hardware installaon | 13

TB350-BTC & TA320-BTC

2.6 Jumper & Switch Setting

The illustraon shows how to set up jumpers. When the jumper cap is placed on pins, the

jumper is “close”, if not, that means the jumper is “open”.

Pin opened Pin closed Pin 1-2 closed

JCMOS1: Clear CMOS Jumper

The jumper allows users to restore the BIOS safe seng and the CMOS data. Please carefully

follow the procedures to avoid damaging the motherboard.

Pin 1-2 Close:

Normal Operaon (default).

Pin 2-3 Close:

Clear CMOS data.

Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for ve seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Load Opmal Defaults and save sengs in CMOS.

14 | Chapter 2: Hardware installaon

2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector

For beer compability, we recommend to use a standard ATX 24-pin power supply for this

connector. Make sure to nd the correct orientaon before plugging the connector.

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

ATXPWR2: ATX Power Source Connector

The connector provides +12V to the CPU power circuit. If the CPU power plug is 4-pin, please

plug it into Pin 1-2-5-6 of ATXPWR2.

Pin Assignment

1 +12V

2 +12V

3 +12V

4 +12V

5 Ground

6 Ground

7 Ground

8 Ground

Note

»

 Beforeyoupoweronthesystem,pleasemakesurethatbothATXPWR1andATXPWR2connectors

havebeenplugged-in.

»

 Insucientpowersuppliedtothesystemmayresultininstabilityortheperipheralsnotfunconing

properly.UseofaPSUwithahigherpoweroutputisrecommendedwhenconguringasystemwith

morepower-consumingdevices.

Chapter 2: Hardware installaon | 15

TB350-BTC & TA320-BTC

AUXPWR1/2: Auxiliary Power for Graphics

(for Bitcoin mining, 4pin power connector must be installed)

This connector is an auxiliary power connecon for graphics cards. Exclusive power for the

graphics card provides beer graphics performance.

Pin Assignment

1 +12V

2 GND

3 GND

4 +5V

SATA_POWER1: SATA Power Connector

This SATA power connector enhances the power of rear USB ports.

Pin Assignment Pin Assignment

1 VCC3 9 VCC5

2 VCC3 10 Ground

3 VCC3 11 N/A

4 Ground 12 Ground

5 Ground 13 12V

6 Ground 14 12V

7 VCC5 15 12V

8 VCC5 --- ---

PANEL1: Front Panel Header

This 16-pin header includes Power-on, Reset, HDD LED, Power LED, and speaker connecon.

Pin Assignment Funcon Pin Assignment Funcon

1 +5V

Speaker

Connector

9 N/A

N/A

2 N/A 10 N/A

3 N/A 11 N/A N/A

4 Speaker 12 Power LED (+)

Power

LED

5 HDD LED (+)

Hard drive

LED

13 Power LED (+)

6 HDD LED (-) 14 Power LED (-)

7 Ground

Reset

buon

15 Power buon

Power-on

buon

8 Reset control 16 Ground

16 | Chapter 2: Hardware installaon

SATA1~SATA4: Serial ATA 6.0 Gb/s Connectors

These connectors connect to SATA hard disk drives via SATA cables.

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

7 Ground

JFRONT_USB3_1: Header for USB 3.1 Gen1 (5Gb/s) Ports at Front Panel

This header allows user to add addional USB ports on the PC front panel, and also can be

connected with a wide range of external peripherals.

Pin Assignment Pin Assignment

1 VBUS0 11 D2+

2 SSRX1- 12 D2-

3 SSRX1+ 13 Ground

4 Ground 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 Ground

7 Ground 17 SSRX2+

8 D1- 18 SSRX2-

9 D1+ 19 VBUS1

10 ID 20 Key

F_USB1/2: Header for USB 2.0 Ports at Front Panel

This header allows user to add addional USB ports on the PC front panel, and also can be

connected with a wide range of external peripherals.

Pin Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

10 NC

Chapter 2: Hardware installaon | 17

TB350-BTC & TA320-BTC

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the chassis-mount front panel audio I/O which supports HD

and AC’97 audio standards.

HD Audio AC’97

Pin Assignment Pin Assignment

1 Mic Le in 1 Mic In

2 Ground 2 Ground

3 Mic Right in 3 Mic Power

4 GPIO 4 Audio Power

5 Right line in 5 RT Line Out

6 Jack Sense 6 RT Line Out

7 Front Sense 7 Reserved

8 Key 8 Key

9 Le line in 9 LFT Line Out

10 Jack Sense 10 LFT Line Out

Note

»

 Itisrecommendedthatyouconnectahigh-denionfrontpanelaudiomoduletothisconnectorto

availofthemotherboard’shighdenionaudiocapability.

»

 Pleasetrytodisablethe“FrontPanelJackDetecon”ifyouwanttouseanAC’97frontaudiooutput

cable.ThefunconcanbefoundviaO.S.AudioUlity.

J_COM1: Serial Port Connector

The motherboard has a serial port header for connecng RS-232 Port.

Pin Assignment

1 Carrier detect

2 Received data

3 Transmied data

4 Data terminal ready

5 Signal ground

6 Data set ready

7 Request to send

8 Clear to send

9 Ring indicator

10 Key

18 | Chapter 3: UEFI BIOS & Soware

Chapter 3: UEFI BIOS & Soware

3.1 UEFI BIOS Setup

• The BIOS Setup program can be used to view and change the BIOS sengs for the

computer. The BIOS Setup program is accessed by pressing the <DEL> key aer the

Power-On Self-Test (POST) memory test begins and before the operang system boot

begins.

• For further informaon of seng up the UEFI BIOS, please refer to the UEFI BIOS Manual

on our website.

3.2 BIOS Update

The BIOS can be updated using either of the following ulies:

• BIOSTAR BIOS Flasher: Using this ulity, the BIOS can be updated from a le on a hard

disk, a USB drive (a ash drive or a USB hard drive), or a CD-ROM.

• BIOSTAR BIOS Update Ulity: It enables automated updang while in the Windows

environment. Using this ulity, the BIOS can be updated from a le on a hard disk, a USB

drive (a ash drive or a USB hard drive), or a CD-ROM, or from the le locaon on the

Web.

BIOSTAR BIOS Flasher

Note

»

 ThisulityonlyallowsstoragedevicewithFAT32/16formatandsingleparon.

»

 ShungdownorresengthesystemwhileupdangtheBIOSwillleadtosystembootfailure.

Updang BIOS with BIOSTAR BIOS Flasher

1. Go to the website to download the latest BIOS le for the motherboard.

2. Then, copy and save the BIOS le into a USB ash (pen) drive.(Only supported FAT/FAT32

format)

3. Insert the USB pen drive that contains the BIOS le to the USB port.

4. Power on or reset the computer and then press <F12> during the POST process.

5. Aer entering the POST screen, the BIOS-

FLASHER ulity pops out. Choose <fs0> to search

for the BIOS le.

Chapter 3: UEFI BIOS & Soware | 19

TB350-BTC & TA320-BTC

6. Select the proper BIOS le, and a message asking

if you are sure to ash the BIOS le. Click “Yes” to

start updang BIOS.

7. A dialog pops out aer BIOS ash is completed,

asking you to restart the system. Press the <Y> key

to restart system.

8. While the system boots up and the full screen logo shows up, press <DEL> key to enter BIOS

setup.

Aer entering the BIOS setup, please go to the <Save & Exit>, using the <Restore Defaults>

funcon to load Opmized Defaults, and select <Save Changes and Reset> to restart the

computer. Then the BIOS Update is completed.

BIOS Update Ulity (through the Internet)

1. Installing BIOS Update Ulity from the DVD Driver.

2. Please make sure the system is connected to the internet before using this funcon.

3. Launch BIOS Update Ulity and click the

“Online Update” buon on the main screen.

4. An open dialog will show up to request your

agreement to start the BIOS update. Click “Yes”

to start the online update procedure.

20 | Chapter 3: UEFI BIOS & Soware

5. If there is a new BIOS version, the ulity will

ask you to download it. Click “Yes” to proceed.

6. Aer the download is completed, you will be

asked to program (update) the BIOS or not. Click

“Yes” to proceed.

7. Aer the updang process is nished, you

will be asked you to reboot the system. Click

“OK” to reboot.

8. While the system boots up and the full screen logo shows up, press <DEL> key to enter BIOS

setup.

Aer entering the BIOS setup, please go to the <Save & Exit>, using the <Restore Defaults>

funcon to load Opmized Defaults, and select <Save Changes> and <Reset> to restart the

computer. Then, the BIOS Update is completed.

BIOS Update Ulity (through a BIOS le)

1. Installing BIOS Update Ulity from the DVD Driver.

2. Download the proper BIOS from hp://www.biostar.com.tw/

3. Launch BIOS Update Ulity and click the “Update

BIOS” buon on the main screen.

4. A warning message will show up to request your

agreement to start the BIOS update. Click “OK” to

start the update procedure.

ページが読み込まれています...

Biostar TB350-BTC ユーザーマニュアル

このマニュアルも適しています

Biostar TB350-BTC ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント