Lian Li UF-SL120V2-3B インストールガイド

安裝指南

INSTALLATION GUIDE /

包裝內容物

Package Contents /

x 3 pcs

x 4 pcs

A 5銅板紙或模糙紙100P單色雙面印刷摺1摺成A6

x 12 pcs

UF-SL120V2-3B / UF-SL120V2-3W

M5x10

RGB

UNI FAN SL120 V2

Power Cable Installation / 電源線安裝

注意 1 !電源線插頭有⽅向性公母插針對接擋板蓋住彈簧端⼦，，。

!Note 1 ! The socket for the power cable modular is directional, which

shall connect the male-female plug and cover the pins.

注意 2 !拉拔端⼦接頭具有卡扣設計，因此不必擔⼼容易鬆脫。

Note 2 ! The pulling connector mechanism is designed to not loosen easily.

Daisy Chain Extension Cable Connection / 使⽤串接延⾧線

Fan to Fan Connection / ⾵扇連接⾵扇

Fixed

Release

Note! Each connector from the controller can connect

maximum 6 fans, no limited quantity for Group A or B.

注意 ! 6 A B⼀個接頭接出來的⾵扇總數不可超過 顆，組或 組

串接⾵扇數量不限。

A Group / A組

B組

B Group /

x 1 pc

x 2 pcs

控制器線材連接

Controller Cable Connection /

G50.12 SLV23.00

Connect to USB

Connect to 5V ARGB

3 pin header

Connect to

PSU SATA 15 Pin

Connect to 1,

or 2, or 3, or 4

連接到 1 或 2，，

或 3 或 4，

5 V 12 V

警告 請不要連接錯誤類型的!

LED接頭如果連接到 1 2 V接⼝，，

將造成永久損壞。

Warning! Do not connect the

wrong type of LED connector. If it

is connected to the 12 V connector,

permanent damage will occur.

Note! Press and pull out the

connector to release the

cable.

注意 按下再拉出線材接頭!。

Press

GND VCC

DATA

SM Type

注意2!本⾵扇為 2 8 m m厚度 採下沉式螺絲孔設計適⽤⼀般常規，，

⾧螺絲(具有隱藏螺絲頭的功能) 無法使⽤墊⽚+⾧螺絲，。

Note 2 ! Implementing counterbore screw holes to fit standard long screws,

do not use gaskets when mounting with long screws.

⽔冷排上的⾵扇安裝

Fan Mounting on Raditor /

注意 1!若遇到⽔冷排出⽔位置影響⾵扇扣鎖可將⾵扇卡扣鎖移除，。

Note 1 ! The fan interlocking key is removable if it is affected by the

radiator inlet and outlet.

控制器 2 個 SATA 15 PIN線材電源全接情況下最⼤輸出如下：，

1. 請勿串接超過 顆⾵扇⾄控制器控制器最⼤輸出為 ，。29 W 16

2.採⽤ L-C onne c t 3󰔥軟體控制⾵扇設為定⾊⽩光請將⽩光亮度降低，。

3.同步主機板亮度開⾄ 100%的定⾊⽩光時最多⽀援8顆UNI FAN SL V2，。

4.控制器上的SM typ e輸出⼝最⼤⽀援5 W ( SYNC 2接⼝同步 2號接⼝燈效；

SYNC 4接⼝同步 4號接⼝燈效)。

Restriction of Controller / 控制器的限制

Maximum output of controller when connected BOTH SATA 15 PIN cable:

1. The maximum total output of the controller supports up to 29 W, do not

connect more than 16 fans to the controller.

2. Use L-Connect 3 to set static white, please lower the brightness.

3. When sync to motherboard and set as 100% brightness of static white, the

controller supports up to 8 . UNI FAN SL V2

4. Each SM type port supports up to 5 W.( SYNC 2 port syncs to the lighting effect

　of　port 2; SYNC 4 port syncs to the lighting effect of port 4)．

Use of Magnetic Adhesive Pad / 磁性膠墊使⽤

注意 3! M 5 x 1 0請使⽤附件裡的 螺絲來安裝⾵扇，以確保⾵扇牢固。

Note 3 ! Only use the screws(M5x10) that is included in the box, other

screws may not hold the fan properly.

Remove

the adhesive

撕下雙⾯膠

Connect to

fan header

Note! Merge lighting effects will be

affected by the installation direction,

please refer to link below for details.

注意 ! 某些燈效會因為⾵扇擺放位置⽽受到

影響，請先掃碼或輸⼊網址參考詳細圖解。

Note! The header is designed with a

clamp, please press the clump to

release the header from the controller.

注意 !此接頭設有卡扣，請向下按壓

卡扣再將接頭拔出控制器。

Lian Li UF-SL120V2-3B インストールガイド

関連論文

その他の書類