Check the Included Items
Before you begin assembling the stand, check that all the items
were supplied.
Symbol Name Quantity
A Bench seat 1
B Legs 4
C Hex bolts *1 4
D Washers *1 4
E Spring washers *1 4
F Wrench *2 1
*1: Attached to the legs.
*2: Attached to the bench seat.
* To prevent injury, work gloves should be worn while
performing the assembly.
* When removing the wrench from the bottom of the seat, pay
attention to the tip of the holder.
Assembly
1. Place the bench seat (A) upside down in a stable
location.
* When placing the bench seat upside down, take care to
protect the seating surface from damage. Handle it with care
so that it does not fall or overturn.
A
2. Attach the legs (B).
Place a spring washer (E) and a washer (D) on each hex bolt (C),
and provisionally tighten each leg (B). At this time, tighten the
hex bolts (C) by hand.
* Place the spring washer (E) and washer (D) on
the hex bolt (C) in that order.
* Note the position of the screw holes in the legs
(B) and the holes in the metal xtures of the
bench seat (A).
D
E
B
B
B
B
B
C
3. Place the bench in the location in which you are going
to use it, and tighten the legs (B).
While applying pressure on the seat, go around and tighten each
hex bolt (C) little by little, while adjusting the position of the legs
as necessary to prevent any wobbling. In other words, tighten
the hex bolt for each leg gradually, a little each time, as you go
around in order starting with leg number 1, then moving to
number 2, then number 3, then number 4; after which you can
go back to number 1 and repeat the process.
* If the height of the bench is adjustable, be careful not to
insert your hand into the metal components of the height
adjustment mechanism.
1
2
3
4
F
If the bench wobbles after you’ve fastened all the legs, rst
loosen the hex bolt for leg number 1. Then, while applying
pressure to the center of the seat, retighten the hex bolt.
If necessary, repeat this process for the other legs until the
wobbling is eliminated.
4. Finally, tighten the hex bolts (C) further, and verify that
none of them are loose.
* Use the included wrench (F) to rmly tighten the hex bolts
(C) until there is no space between the spring washers (E) and
the washers (D).
OK
D
E
C
Completed bench
* In the interest of product improvement, the speci cations
and/or appearance of this product are subject to change
without prior notice.
Maintenance
At regular intervals, please check that the hex bolts are rmly
tightened and that the legs are stable. If any hex bolts are loose,
retighten them.
If you notice any other abnormality, immediately stop using the
bench, and contact your dealer for service.
Musical Instrument Bench
Owner’s Manual
Before using this product, carefully read the sections entitled: ”USING THE UNIT SAFELY” and ”IMPORTANT NOTES.” These sections provide important informa-
tion concerning the proper operation of this product. Additionally, the Owner’s manual should be saved and kept on hand as a convenient reference.
USING THE UNIT SAFELY IMPORTANT NOTES
D
E
C
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
About WARNING and CAUTION Notices
About the Symbols
ALWAYS OBSERVE THE FOLLOWING
WARNING
Do not disassemble or modify by yourself
Do not carry out anything unless you
are instructed to do so in the owner’s
manual. Otherwise, you risk causing
malfunction.
Do not repair or replace parts by yourself
Refer all servicing to your retailer, the
nearest Roland Service Center, or an
authorized Roland distributor, as listed
on the “Information.”
Do not use or store in the following types of
locations
• Subject to temperature extremes (e.g.,
direct sunlight in an enclosed vehicle,
near a heating duct, on top of heat-
generating equipment); or are
• Damp (e.g., baths, washrooms, on wet
oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and shakiness.
Do not place in an unstable location
Otherwise, you risk injury as the result of
this product toppling over or dropping
down.
Be cautious to protect children from injury
Always make sure that an adult is
on hand to provide supervision and
guidance when using this product in
places where children are present, or
when a child will be using this product.
Do not drop or subject to strong impact
Otherwise, you risk causing damage or
malfunction.
CAUTION
Take care so as not to get ngers pinched
When handling the following moving
parts, take care so as not to get ngers,
toes, etc., pinched. Whenever a child uses
this product, an adult should be on hand
to provide supervision and guidance.
• Height adjustment handle
Precautions concerning use of bench
When using the bench, please observe
the following points:
• Do not use the bench as a toy, or as a
stepping stool.
• Do not allow two or more persons to
sit on the bench.
• Do not adjust the height while sitting
on the bench.
• Do not sit on the bench if the bolts holding
the bench legs are loose. (If the bolts are loose,
immediately re-tighten them using the supplied
tool.)
• Never insert your hand into the gap (the metal
height adjustment mechanism) under the seat
lid. Doing so may cause your hand to be pinched
or injured.
Keep small items out of the reach of children
To prevent accidental ingestion of the
parts listed below, always keep them out
of the reach of small children.
• Included Parts
• Washers
• Spring washers
Placement
• Do not expose this product to direct sunlight,
place it near devices that radiate heat, leave it
inside an enclosed vehicle, or otherwise subject
it to temperature extremes. Also, do not allow
lighting devices that normally are used while
their light source is very close to this product
(such as a piano light), or powerful spotlights
to shine upon the same area of this product for
extended periods of time. Excessive heat can
deform or discolor this product.
• Do not allow rubber, vinyl, or similar materials to
remain on this product for long periods of time.
Such objects can deform or discolor this product.
• Do not paste stickers, decals, or the like to this
product. Peeling such matter o this product
may damage the exterior nish.
• Do not place containers or anything else
containing liquid on top of this product. Also,
whenever any liquid has been spilled on the
surface of this product, be sure to promptly wipe
it away using a soft, dry cloth.
Maintenance
• If the unit should become soiled, wipe it with a
soft dry cloth or a rmly wrung-out cloth. Wipe
with even pressure across the entire unit. The
nish may be damaged if you strongly rub only a
speci c location.
• Never use benzine, thinners, alcohol or
solvents of any kind, to avoid the possibility of
discoloration and/or deformation.
Additional Precautions
• Do not apply excessive force to the height
adjustment handle, since this could cause
malfunctions.
• When you need to transport this product, pack
it in shock-absorbent material. Transporting
this product without doing so can cause it to
become scratched or damaged, and could lead
to malfunction.
• When adjusting the height of the seating
surface, take care not to pinch your ngers in the
movable parts. If the unit is used where small
children are present, you must provide adult
supervision and guidance.
• This unit is a bench speci cally designed for
use with musical instruments. Use it only when
playing a musical instrument. Sit on the center
of the bench.
• In some cases, the color of your clothing might
transfer to the seating surface. Do not use this
bench when wearing dark-colored clothing.
• If you use this bench on a wood oor or a woven
mat, the legs of the bench could leave marks on
its surface. In such cases, we recommend that
you place a rug or similar protective surface
under the bench.
• If you tighten the height adjustment handle
excessively, it may stop working.
* 5 1 0 0 0 4 1 3 1 2 - 0 1 *
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US
(
Proposition 65
)
©2014 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Roland is a registered trade mark of Roland Corporation in the United States and/or other countries.
-
1
-
2
他の言語で
- English: Roland BNC-05 Owner's manual
その他のドキュメント
-
Tektronix K420 Instructions Manual
-
Hikoki C 12LSH ユーザーマニュアル
-
Matrix MD-S70 取扱説明書
-
Matrix G7-S23 取扱説明書
-
-
-
-
-
Ingersoll-Rand ST750GBDI03R31 Installation And Maintenance Information
-
Walker Edison Furniture Company HDW42VINCTDB インストールガイド
