Dell PowerEdge T610 クイックスタートガイド

FILE LOCATION: M:\Enterprise\Sneetch 5u (Whoville)\DL1486 - Getting Started Guide\APCC - CX823

A01\EN\CX823_fc1.fm

DELL CONFIDENTIAL – PRELIMINARY 1/14/09 – FOR PROOF ONLY

Current template as of 4/26/2007

Dell™ PowerEdge™

T610 Systems

Getting Started

With Your System

系统使用入门

Memulai Dengan Sistem Anda

はじめに

시스템시작하기

Dell™ PowerEdge™

T610 Systems

Getting Started

With Your System

Model E03S

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.; Citrix and XenServer are trademarks

of Citrix Systems, Inc. and/or more of its subsidiaries, and may be registered in the United States

Patent and Trademark Office and in other countries. Intel and Xeon are registered trademarks of Intel

Corporation in the U.S. and other countries; Microsoft, Hyper-V, Windows, and Windows Server are

either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other

countries. Red Hat and Enterprise Linux are registered trademarks of Red Hat, Inc. in the United States

and other countries; SUSE is a registered trademark of Novell, Inc., in the United States and other

countries. VMware is a registered trademark of VMware, Inc. in the United States and/or other

jurisdictions.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model E03S

December 2008 P/N CX823 Rev. A01

CX823_tp1.fm Page 4 Friday, January 16, 2009 3:18 PM

Getting Started With Your System 3

Installation and Configuration

WARNING: Before performing the following procedure, review the safety

instructions that came with the system.

NOTE: If you are using the optional rack configuration, assemble the rails

and install the system in the rack following the safety instructions and the rack

installation instructions provided with your system.

Stabilizing the Tower System

WARNING: The tower system has four feet on its bottom panel that can be

extended outward to help properly stabilize the system. Failure to extend the

feet poses the risk of having the system tip over, possibly causing bodily injury

or damage to the system.

4 Getting Started With Your System

Optional – Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Connecting the Power Cables

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

Getting Started With Your System 5

Securing the Power Cord

Bend the system power cable into a loop as shown in the illustration

and secure the cable to the bracket using the provided strap.

Plug the other end of the power cables into a grounded electrical outlet

or a separate power source such as an uninterruptible power supply (UPS)

or a power distribution unit (PDU).

Turning on the System

Press the power button on the system. The power indicators should light.

6 Getting Started With Your System

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system

for the first time, see the installation and configuration documentation for

your operating system. Be sure the operating system is installed before

installing hardware or software not purchased with the system.

• Citrix

®

XenServer

™

5.0 with hotfix 1 or later

• Microsoft

®

Windows Server

®

2008 Hyper-V

™

• Microsoft Windows Server 2008 Web, Standard, and Enterprise

(32-bit x86) Gold editions

• Microsoft Windows Server 2008 Web, Standard, Enterprise,

and Datacenter (x64) Gold editions

• Microsoft Window Small Business Server 2008, Standard and Premium

(x64) editions.

• Microsoft Windows Server 2003 Web, Standard, and Enterprise

(32-bit x86) editions with SP2

• Microsoft Windows Server 2003 Standard and Enterprise (x64) editions

with SP2

• Microsoft Windows Server 2003 R2 Standard and Enterprise (32-bit x86)

editions with SP2

• Microsoft Windows Server 2003 R2 Standard, Enterprise, and Datacenter

(x64) editions with SP2

• Microsoft Windows Small Business Server 2003 R2 Standard and Premium

editions with SP2

•Red Hat

®

Enterprise Linux

®

ES and AS 4.7 (x86)

• Red Hat Enterprise Linux ES and AS 4.7 (x86_64)

• Red Hat Enterprise Linux 5.2 Server (x86_32)

• Red Hat Enterprise Linux 5.2 Server (x86_64)

• SUSE Linux Enterprise Server 10 SP2 (x86_64)

• VMware

®

ESX Version 4.0 and 3.5, Update 4 (when available)

• VMware ESXi Version 4.0 and 3.5, Update 4 (when available)

NOTE: For the latest information on supported operating systems,

see www.dell.com.

Getting Started With Your System 7

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document

or as a separate document.

• The rack documentation included with your rack solution describes

how to install your system into a rack.

•The

Hardware Owner’s Manual

provides information about system features

and describes how to troubleshoot the system and install or replace system

components. This document is available online at

support.dell.com.

• Any media that ships with your system that provides documentation

and tools for configuring and managing your system, including those

pertaining to the operating system, system management software, system

updates, and system components that you purchased with your system.

NOTE: Always check for updates on support.dell.com and read the updates

first because they often supersede information in other documents.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not

perform as expected, see your Hardware Owner’s Manual. Dell

™

offers

comprehensive hardware training and certification. See www.dell.com/training

for more information. This service may not be offered in all locations.

Información de la NOM (sólo para México)

La información que se proporciona a continuación aparece en el dispositivo

descrito en este documento, en cumplimiento de los requisitos de la Norma

Oficial Mexicana (NOM):

Importador:

Número de modelo: E03S

Voltaje de

alimentación: 100–240 V CA

Frecuencia: 50/60 Hz

Consumo eléctrico: 7,0–3,5 A

8 Getting Started With Your System

Technical Specifications

Processor

Processor type One or two quad- or dual-core Intel

®

Xeon

®

processors

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots: Two full-height, full-length x8 link

(slots 2 and 3)

Three full-height, half-length x4 link

(slots 1, 4 and 5)

NOTE: All slots support up to 25W, but

a maximum of two 25W cards and three

15W cards may be installed at any time,

regardless of the slots they are installed in.

Memory

Architecture 800, 1066, or 1333 MHz DDR3 registered

or unbuffered Error Correcting Code (ECC)

DIMMs. Support for Advanced ECC

or Memory Optimized operation.

Memory module sockets Twelve 240-pin

Memory module capacities 1 GB and 2 GB UDIMMs; and 2 GB, 4 GB,

or 8 GB RDIMMs (single, dual, or quad-rank,

dependent on capacity)

Minimum RAM 1 GB with a single processor

(1 DIMM per processor)

Maximum RAM 96 GB (with quad-rank 8 GB RDIMMs)

or 24 GB (with 2 GB UDIMMs)

Getting Started With Your System 9

Drives

Hard drives Up to eight 2.5-inch internal, hot-swappable

SAS or SATA hard drives with backplane

support

or

Up to eight 3.5-inch internal, hot-swappable

SAS or SATA hard drives with backplane

support

Diskette drive Optional external USB 1.44 MB drive

Optical drive One or two optional internal SATA DVD,

or DVD+RW drive

Optional external USB DVD

NOTE: DVD devices are data only

NOTE: If a half-height tape drive is installed, you can install one internal optical drive.

If a full-height tape drive is installed, no optical drives can be installed.

Tape drive One optional half-height (for use in one

optical drive bay) SAS, SATA or SCSI

with optional SCSI controller card

One optional full-height (for use in both

optical drive bays) SAS or SCSI with optional

SCSI controller card.

Flash drive Optional internal USB

Optional internal Secure Digital (SD)

memory card

Optional external SD memory card

Connectors

Back

NIC

Two RJ-45 for integrated 10/100/1000 Mbps

Ethernet

Serial

9-pin, DTE, 16550-compatible

USB

Six 4-pin, USB 2.0-compliant

Video

15-pin VGA

10 Getting Started With Your System

Optional external VFlash card

One optional flash memory card slot

with iDRAC6 Enterprise

Front

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

One 4-pin, USB 2.0-compliant

Internal secure digital (SD)

module

One optional flash memory card slot

on internal SD module

Video

Video type Integrated Matrox G200

Video memory 8 MB shared

Power

AC Power Supply (per power supply)

Wa tt ag e

870 Watt (High Output)

570 Watt (Energy Smart)

Voltage

90–264 VAC, autoranging, 47-63 Hz

Heat dissipation

2968.6 BTU/hr maximum (High Output)

1944.9 BTU/hr maximum (Energy Smart)

Maximum inrush current

Under typical line conditions and over the

entire system ambient operating range, the

inrush current may reach 55 A per power

supply for 10 ms or less.

Batteries

System battery

CR 2032 3.0 V lithium coin cell

RAID battery (optional)

3.7 V lithium ion battery pack

Connectors (continued)

Getting Started With Your System 11

Physical

Rack

Height

21.77 cm (8.57 in)

Width

48.25 cm (19.00 in)

(includes left and right rack latches)

Depth

62.10 cm (24.45 in)

(includes power supply with bezel)

Weight (maximum configuration)

35 kg (77 lb)

Weight (empty)

20.2 kg (44.53 lb)

Tower

Height (with feet)

44.10 cm (17.40 in)

Width (with feet)

27.40 cm (10.80 in)

Depth

62.10 cm (24.45 in)

(includes power supply with bezel)

Weight (maximum configuration)

35 kg (77 lb)

Weight (empty)

20.55 kg (45.30 lb)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE: For altitudes above 2950 feet, the

maximum operating temperature is derated

1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with a maximum

temperature gradation of 20°C per hour

Relative humidity

Operating

20% to 80% (non-condensing) with

a maximum humidity gradation of

10% per hour

12 Getting Started With Your System

Storage

5% to 95% (non-condensing) with a maximum

humidity gradation of 10% per hour

Maximum vibration

Operating

0.26 Gms from 5–350 Hz for 5 minutes

in operational orientations

Storage

1.54 Gms from 10–250 Hz for 10 minutes

in all orientations

Maximum shock

Operating

Half sine shock in all operational orientations

of 31 G plus or minus 5% with a pulse

duration of 2.6 ms plus or minus 10%

Storage

Half sine shock on all six sides of 71 G plus or

minus 5% with a pulse duration of 2 ms plus

or minus 10%

Square wave shock on all six sides of 27 G

with a velocity change at 235 in/sec or greater

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet, the

maximum operating temperature is derated

1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Environmental (continued)

Dell™ PowerEdge™

T610 系统

系统使用入门

型号

E03S

注、小心和警告

注：

“注”表示可以帮助您更好地使用计算机的重要信息。

警告：

“警告”表示可能会造成财产损失、人身伤害甚至死亡。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式复制这些材料。

Dell

、

DELL

徽标和

PowerEdge

是

Dell Inc.

的商标；

Citrix

和

XenServer

是

Citrix Systems, Inc.

和

/

或其多个子公司的商标，并可能已在美国专利商标局和其它国家和地区注册。

Intel

和

Xeon

是

Intel Corporation

在美国

和其它国家和地区的注册商标；

Microsoft

、

Hyper-V

、

Windows

和

Windows Server

是

Microsoft Corporation

在美国和

/

或其它国家和地区的商标或注

册商标。

Red Hat

和

Enterprise Linux

是

Red Hat, Inc.

在美国和其它国家和地区的注册商标；

SUSE

是

Novell, Inc.

在美国和其它国家和地区的注册商标。

VMware

是

VMware, Inc.

在美国

和

/

或其它管辖区域的注册商标。

本说明文件中述及的其它商标和产品名称是指拥有相应商标和产品名称的公司或其制造的

产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。

型号

E03S

2008

年

12

月

P/N CX823 Rev. A01

系统使用入门 15

安装和配置

警告：

执行下列步骤之前，请复习系统随附的安全说明。

注：如果您使用可选的机架配置，请按照系统附带的安全说明和机架安装

说明组装滑轨并在机架中安装系统。

固定塔式系统

警告：

塔式系统在其底部面板上有四个支脚，可向外伸展以帮助正确

固定系统。如果未伸展支脚，可能会导致系统倾翻，以此造成人身伤

害或系统损坏。

16 系统使用入门

可选

–

连接键盘、鼠标和显示器

连接键盘、鼠标和显示器（可选）。

系统背面的连接器附有图标，这些图标指示了要插入每个连接器的电缆。

确保拧紧显示器的电缆连接器上的螺钉（如果有）。

连接电源电缆

连接系统电源电缆至系统，并且，如果使用显示器，连接显示器电源电缆至

显示器。

系统使用入门 17

固定电源线

如图所示，将系统电源电缆弯曲成环状，然后使用提供的电缆带将电缆固定

到支架上。

将电源电缆的另一端插入接地的电源插座或单独的电源（如不间断电源

设备

[UPS]

或配电装置

[PDU]

）。

开启系统

按下系统上的电源按钮。电源指示灯将会亮起。

18 系统使用入门

完成操作系统安装

如果购买了预安装的操作系统，请参阅随系统提供的操作系统说明文件。

第一次安装操作系统，请参阅操作系统的安装和配置说明文件。

请确保先安装操作系统，然后再安装未预装的硬件或软件。

•

Citrix

®

XenServer

™

5.0

，附带热修补程序

1

或更高版本

•

Microsoft

®

Windows Server

®

2008 Hyper-V

™

•

Microsoft Windows Server 2008 Web

、

Standard

和

Enterprise

（

32

位

x86

）

Gold

版

•

Microsoft Windows Server 2008 Web

、

Standard

、

Enterprise

和

Datacenter (x64) Gold

版

•

Microsoft Windows Small Business Server 2008 Standard

和

Premium

(x64)

版

•

Microsoft Windows Server 2003 Web

、

Standard

和

Enterprise

（

32

位

x86

）版（含

SP2

）

•

Microsoft Windows Server 2003 Standard

和

Enterprise (x64)

版（含

SP2

）

•

Microsoft Windows Server 2003 R2 Standard

和

Enterprise

（

32

位

x86

）版（含

SP2

）

•

Microsoft Windows Server 2003 R2 Standard

、

Enterprise

和

Datacenter

（

x64)

版（含

SP2

）

•

Microsoft Windows Small Business Server 2003 R2 Standard

和

Premium

版（含

SP2

）

•

Red Hat

®

Enterprise Linux

®

ES

和

AS 4.7 (x86)

•

Red Hat Enterprise Linux ES

和

AS 4.7 (x86_64)

•

Red Hat Enterprise Linux 5.2 Server (x86_32)

•

Red Hat Enterprise Linux 5.2 Server (x86_64)

•

SUSE Linux Enterprise Server 10 SP2 (x86_64)

•

VMware

®

ESX

版本

4.0

和

3.5

，

Update 4

（如果有）

•

VMware ESXi

版本

4.0

和

3.5

，

Update 4

（如果有）

注：有关支持的操作系统的最新信息，请访问 www.dell.com。

ページが読み込まれています...

Dell PowerEdge T610 クイックスタートガイド

Dell PowerEdge T610 クイックスタートガイド

関連論文