KYOCERA FS-C8100DN 取扱説明書

Operation Guide

Manuel d’utilisation

Guía de uso

Einführung

Guida alle funzioni

Data Security Kit (D)

1-1

General User Information

Table of Contents

Introduction .................................................................................... 1-1

Introduction

This operation guide contains information on the proper use of the Data

Security Kit (D) (hereinafter, Security Kit), as well as cautionary notes relating

to its use. Be sure to carefully read this operation guide before using the

Security Kit.

About The Security Kit

Overwriting

The machine to install this Security Kit (hereinafter, the machine) functions by

temporarily storing scanned data on an internal hard disk. Printing is performed

using this data. Even after the printing is completed, the data remains stored

on the hard disk until it is overwritten by other data. Therefore, there is a

possibility that confidential information will be leaked if special tools are used to

recover this remaining data.

The Security Kit overwrites old data - data that is not required - and data

storage area where the data has been deleted to ensure that data cannot be

recovered. Overwriting is performed automatically, without user intervention.

Data not Secured by Overwriting

The Security Kit secures data that is no longer required after printing or

deleted. This means that the responsibility for maintaining data before it is

printed or data that is stored before it is deleted lies with the user.

1

E

ng

li

s

h

1-2

General User Information

The data derived from the following functions must be administered by the

user.

• Document Management (Copy Function)

• Quick Copy (Printer Function)

• Proof and Hold (Printer Function)

• Private Print (Printer Function)

• Stored Job (Printer Function)

• Virtual MailBox (VMB) (Printer Function)

• Temporary code Job (Printer Function)

• Permanent code Job (Printer Function)

• FAX Function

Encrypting

The machine temporarily stores scanned data on a hard disk. If the hard disk is

stolen, there is a risk the data might be passed to unauthorized parties or

modified.

The Security Kit encrypts data stored on the hard disk, rendering it unreadable

for other than normal print operations.

Also, since this encryption process occurs automatically, no special operation

is required.

1-3

General User Information

Display during overwrite

Important!

To avoid damaging the hard disk, do not turn the machine power off during

overwrite (while the hard disk icon is alternating between the two icons).

Note • If the machine power is turned off while overwriting is still in progress, any

data that has not yet been overwritten will remain on the hard disk. In this

case, overwriting should be re-started from the beginning when the

machine is turned on again.

• In rare cases after the machine power is turned off during overwrite, the

hard disk icon may not change to . This means that overwrite may not

be possible because data was corrupted during data overwriting. Though

the machine will be able to overwrite other old data after printing, contact

your administrator responsible for the machine operation and security to

restore the overwriting feature back to normal.

Icon display Details

The hard disk contains old data.

Alternating Old data is being overwritten.

Old data has been overwritten.

A4

Paper Size Set

Combine

Sheet

Margin/

Centering

Color func.FunctionUser choiceBasic

A4

Plain

A3

Color

A4

Plain

A4

Plain

MP tray

Plain

APS

Auto %

Reduce

％100

Exposure

Auto

Staple

Left Top

Staple Off

％100

Exposure

/EnlargeMode

Erase

Program

Ready to copy. ( Full-Color )

Hard disk icon

1-4

General User Information

Data to be overwritten

Data to be overwritten are as follows.

Data to be Encrypted

Note The Security Kit immediately overwrites the original document data stored onto

the hard disk when copying, scanning or printing is cancelled while processing.

Hard disk is not used with the FAX function.

Copy Function

The original document data of a copy which output is completed

The original document data stored through a document management

function and deleted by the user

The original document data stored in Synergy Print Box that is deleted

because the expiration date was reached

Printer Function (when optional hard disk is installed)

Post-output print data

Print data in the private print mode and virtual mailbox function when

output is completed

Quick Copy, proof and hold, and Private Print data (Deleted when

power is turned off and then back on again.)

Data deleted by the user using the Quick Copy, proof and hold, Private

Print, Stored Job, virtual mailbox, Temporary code Job, or Permanent

code Job function

Data deleted when maximum number of documents is exceeded by

Quick Copy, or proof and hold print data

Data deleted when storage capacity is exceeded by Temporary code

Job print data

Scanner Function

Scanned original document data

Copy/Scanner Function

Scanned original document data

1-5

Administrator Information

Table of Contents

Introduction .................................................................................... 1-5

Security Kit Functions ................................................................... 1-9

Security Kit Installation Procedures .......................................... 1-14

Hard Disk Format ......................................................................... 1-17

Error Messages ............................................................................ 1-18

Introduction

This operation guide contains information on the proper use of the Data

Security Kit (D) (hereinafter, Security Kit), as well as cautionary notes relating

to its use. Be sure to carefully read this operation guide before using the

Security Kit. This operation guide also is intended for administrators

responsible for management and security of the The machine to install this

Security Kit (hereinafter, the machine). The administrator should store this

guide in a secure place.

Attachments

The Security Kit comes with the following items:

• Security key (attached to the machine by the service representative)

• Operation guide (this manual)

• Installation guide (for use by service representative)

About The Security Kit

Overwriting

This machine functions by temporarily storing scanned data on an internal hard

disk. Printing is performed using this data. Even after the printing is completed,

the data remains stored on the hard disk until it is overwritten by other data.

Therefore, there is a possibility that confidential information will be leaked if

special tools are used to recover this remaining data.

The Security Kit overwrites old data - data that is not required - and data

storage area where the data has been deleted to ensure that data cannot be

recovered. Overwriting is performed automatically, without user intervention.

1-6

Administrator Information

Data not Secured by Overwriting

The Security Kit secures data that is no longer required after printing or

deleted. This means that the responsibility for maintaining data before it is

printed or data that is stored before it is deleted lies with the user.

The data derived from the following functions must be administered by the

user.

• Document Management (Copy Function)

• Quick Copy (Printer Function)

• Proof and Hold (Printer Function)

• Private Print (Printer Function)

• Stored Job (Printer Function)

• Virtual MailBox (VMB) (Printer Function)

• Temporary code Job (Printer Function)

• Permanent code Job (Printer Function)

• FAX Function

Encrypted

This machine can temporarily store scanned data on a hard disk. If the hard

disk is stolen, there is a risk the data might be passed to unauthorized parties

or modified.

The Security Kit encrypts data stored on the hard disk, rendering it unreadable

for other than normal print operations.

Also, since this encryption process occurs automatically, no special operation

is required.

The Security Kit works on data on the machine internal hard disk but does not

secure any other type of data (such as data sent to other computers). Note that

data security is not guaranteed even if only one of the conditions required

for data security described below is not met.

Conditions Required for Data Security

The followings are required for fulfilling the validity of data security using the

Security Kit.

Dependable Administrator

A dependable administrator is required in the department to take responsibility

on security on the machine using this Security Kit.

1-7

Administrator Information

Safe Physical Location of Installation

The machine should be installed in a location which the accessibilities are

limited. This avoids unauthorized personnel to use the machine.

Dependable Service Representative

All maintenance activities must be performed by the service representative,

with the administrator in attendance.

1-8

Administrator Information

About Security Mode

Security mode refers to the machine status in which Security Kit has been

installed onto the machine and is operating normally. When security mode is

active, a hard disk icon is shown in the upper right corner of the touch panel.

When security mode is active, a hard disk icon is shown in the upper right

corner of the touch panel.

(The hard disk icon is displayed on the copy, printer and scanner function

screens).

Important!

If a hard disk icon is not displayed on the screen of the copier, printer, and

scanner functions, it could mean that the machine is not in the security mode.

Contact your service representative.

Note You can determine the operational status of the overwrite function by

monitoring changes to the image of the hard disk icon. See page 1-11 Display

during overwrite for further details.

A4

Paper Size Set

Combine

Sheet

Margin/

Centering

Color func.FunctionUser choiceBasic

A4

Plain

A3

Color

A4

Plain

A4

Plain

MP tray

Plain

APS

Auto %

Reduce

％100

Exposure

Auto

Staple

Left Top

Staple Off

％100

Exposure

/EnlargeMode

Erase

Program

Ready to copy. ( Full-Color )

Hard disk icon

1-9

Administrator Information

Security Kit Functions

Overwrite Function

Function details

Overwrites old document data when copying or printing is completed.

Overwriting method

3-time Overwrite or Once Overwrite (See page 1-15 Step 3: Hard Disk

Overwrite for further details.)

Execution timing

Overwrites existing old document data after a job is completed.

Data to be overwritten

See page 1-12 Data to be overwritten for further details.

Overwrite-in-Progress Screen

The hard disk icon alternates between the two icons (See page 1-11

Display during overwrite for further details.)

Security Kit

Copy

Function

Scanner

Function

Printer

Function

Hard Disk

Sends to

computer

Output

1 Monitors the status of

operations, overwrites

old image data.

2 Formats the hard disk.

Temporarily

stores original

document data

Optional Hard Disk

1-10

Administrator Information

Encryption Function

Format Function

Overwriting Time

Differs depending on amount of data to overwrite.

Function details

Encrypts data stored on the hard disk

Execution timing

Encrypts original document data as it is written to disk decrypted when

outputting original document data.

Encrypted Data

See 1-13 Data to be Encrypted for further details.

Function details

Overwrites all data on the hard disk.

Overwriting method

3-time Overwrite or Once Overwrite (See page 1-15 Step 3: Hard Disk

Overwrite for further details.)

Execution timing

Execution through the operation panel (See page 1-17 Hard Disk

Format for further details.)

Data to be overwritten

See page 1-13 Data overwritten through the format function for

further details.

Overwrite-in-Progress Screen

Formatting Hard Disk is displayed.

Overwriting Time

See page 1-13 Time required to format for further details.

1-11

Administrator Information

Hard Disk Overwrite

You can select either of the following two methods to overwrite data:

Display during overwrite

Important!

To avoid damaging the hard disk, do not turn the machine power off during

overwrite (while the hard disk icon is alternating between the two icons).

Once Overwrite

Overwrites the entire area used to store old document data with zeroes

to reject recovery of the data. The entire hard disk is overwritten with

zeroes during a format operation.

3-time Overwrite (Default)

Overwrites the entire area used to store old document data twice with a

random pattern and then a third and final time with zeroes. It takes

longer to execute than the Once Overwrite, but because even highly-

sophisticated recovery methods are unable to recover the data, this

method provides higher security. The area to be overwritten is the

same as for the Once Overwrite.

Icon display Details

The hard disk contains old data.

Alternating Old data is being overwritten.

Old data has been overwritten.

A4

Paper Size Set

Combine

Sheet

Margin/

Centering

Color func.FunctionUser choiceBasic

A4

Plain

A3

Color

A4

Plain

A4

Plain

MP tray

Plain

APS

Auto %

Reduce

％100

Exposure

Auto

Staple

Left Top

Staple Off

％100

Exposure

/EnlargeMode

Erase

Program

Ready to copy. ( Full-Color )

Hard disk icon

1-12

Administrator Information

Note • If the machine power is turned off while overwriting is still in progress, any

data that has not yet been overwritten will remain on the hard disk. In this

case, overwriting should be re-started from the beginning when the

machine is turned on again.

• In rare cases after the machine power is turned off during overwrite, the

hard disk icon may not change to . This means that overwrite may not

be possible because data was corrupted during data overwriting. Though

the machine will be able to overwrite and overwrite data that is not

required after it is printed, the hard disk will need to be re-formatted in

order to restore overwriting to normal. (See page 1-17 Hard Disk Format.)

Data to be overwritten

Data to be overwritten are as follows.

Copy Function

The original document data of a copy which output is completed

The original document data stored through a document management

function and deleted by the user

The original document data stored in Synergy Print Box that is deleted

because the expiration date was reached

Printer Function (when optional hard disk is installed)

Post-output print data

Print data in the private print mode and virtual mailbox function when

output is completed

Quick Copy, proof and hold, and Private Print data (Deleted when

power is turned off and then back on again.)

Data deleted by the user using the Quick Copy, proof and hold, Private

Print, Stored Job, virtual mailbox, Temporary code Job, or Permanent

code Job function

Data deleted when maximum number of documents is exceeded by

Quick Copy, or proof and hold print data

Data deleted when storage capacity is exceeded by Temporary code

Job print data

Scanner Function

Scanned original document data

1-13

Administrator Information

Data to be Encrypted

Note

The Security Kit immediately overwrites the original document data stored onto

the hard disk when copying, scanning or printing is cancelled while processing.

Hard disk is not used with the FAX function.

Data overwritten through the format function

Data overwritten through the format function are as follows.

Time required to format

Time required to format are as follows.

Copy/Scanner Function

Scanned original document data

Copy Function

Job Accounting data

Original document data stored with the document management

function

Printer Function (when optional hard disk is installed)

Data stored in Stored Job mode

Program data

Optional font

Macro data

Scanner Function

Common book

Overwriting method Formatting time

Once Overwrite Max 0.5 hours

3-time Overwrite Max 1.5 hours

1-14

Administrator Information

Security Kit Installation Procedures

Step 1: Preparation

Security Kit installation

The Security Kit is installed by service representative.

Precautions for Security Kit installation

• The repeat copy function becomes prohibited.

• The Delete Invalid Data menu is replaced by the Format Hard Disk menu.

• All original document data saved on the hard disk is overwritten.

Precautions for installing the security kit on a machine already in

production

After installing the Security Kit, you must format all hard disks.

Step 2: Changing the Management code

The management code must be entered to use the Security Kit. Changing the

management code prevents everyone except the administrator from using the

Security Kit. The management code is eight digits long when using security

mode.

Important!

Avoid using a management code that is easily guessed, such as 11111111 or

12345678.

Note You can change the management code within the range of 00000000 to

99999999.

Be sure to use eight digits.

1

Press the System Menu/Counter key.

2

Press the Machine Default key.

3

Use the numeric keys to enter the management code. The default setting is

25002500 for the 25/20 cpm model and 32003200 for the 32/25 and 32/32 cpm

models.

4

Press and keys to select Change Management Code and press

Change # key.

1-15

Administrator Information

5

Enter the new management code using the numeric keys.

6

Press the Close key.

Step 3: Hard Disk Overwrite

Selects the hard disk overwrite. See page 1-11 Hard Disk Overwrite for

further details.

Note Note that it does not apply to overwrite and formatting individually.

1

Press the System Menu/Counter key.

2

Press the Machine Default key.

3

Use the numeric keys to enter the management code. The default setting is

25002500 for the 25/20 cpm model and 32003200 for the 32/25 and 32/32 cpm

models.

4

Select Hard Disk Overwrite from the left side setting field, and press the

Change # key.

5

Press 3-time Overwrite or Once Overwrite.

6

Press the Close key.

Management code change Back Close

Mac hine DefaultSystem Menu

Change the management code.

-

Use the numeric keys to set 8 digit numbers.

27451172

Clear

Hard Disk Overwrite

Back Close

Mac hine Default

Select the hard disk overwrite.

Once

System Menu

3-time

Overwrite

-

1-16

Administrator Information

Step 4: Changing Hard Disk Encryption Key

Change the encryption key

1

Press System Menu/Counter key.

2

Press Machine default key.

3

Press and keys to select HDD Encryption Key and press Change #

key.

4

Press Change # for the Encryption Key.

5

Input the 16 character encryption key and press End key. Returns to the HDD

Encryption Key screen.

6

To ensure that the key has been input correctly, press Change # key of

Confirm Encryption Key, enter the same key again, and press End key.

Returns to the HDD Encryption Key screen.

7

Press the Close key.

8

Press Yes key when a confirmation dialog appears.

All original document data saved on the hard disk is overwritten. When

overwriting is complete, the screen returns to the System Menu/Counter

screen.

Clos eHDD Encryption Key Back

Change #

Encryption Key

:Confirm Enc ryption Key

Changes the key to encrypt data. Enter 16 digits.

Changing the key will cause data to be overwritten.

:

Sy s tem Menu Mac hine Default-

Stop

Yes

The encryption key will be changed. Changing the key

will cause data stored in the Hard Disk to be overwritten.

No

Are you s ure?

1-17

Administrator Information

Hard Disk Format

Format the hard disk when disposing of the machine or the hard disk to

overwrite the hard disk data. See page 1-10 Format Function for further

details.

Important!

To avoid damaging the hard disk, do not turn the power off while formatting the

hard disk. If the formatting is not completed, there is a possibility of data being

recovered from the hard disk and information being leaked.

Note • The Security Kit re-starts formatting the Hard Disk when power is turned of

and then on.

• If the optional hard disk is installed, the hard disk is also formatted.

1

Press the System Menu/Counter key.

2

Press the BOX Management key.

3

Use the numeric keys to enter the management code. The default setting is

25002500 for the 25/20 cpm model and 32003200 for the 32/25 and 32/32 cpm

models.

4

Press the On key under Format Hard Disk (on the right side of the touch

panel).

5

When you prompted to confirm formatting, press the Yes key. Formatting

begins.

6

After formatting is completed, turn off the Main Switch and unplug the Power

Cord.

Clos e

HDD management mode

System Menu

Check Hard Disk capacity

Check the free space and capacity

of the Hard Disk.

On

Format Hard Disk

Overwrite data on the Hard Disk.

Data cannot be restored.

On

1-18

Administrator Information

Error Messages

Contact your service representative or authorized service center if any of the

following messages are displayed.

Message Details

Security key is not recognized.

Not available.

Security key is not connected

properly or is damaged.

ページを読み込んでいます...

KYOCERA FS-C8100DN 取扱説明書

関連論文

その他の書類