V.S.W.R. & Power Meter Instruction Manual
This SWR & Power meter is a highly accurate RF meter for
measuring Forward Power,Reflected Power, and VSWR.
Main Features:
· Large meter display for easy reading.
· Forward RF power readings, switchable to indicate either average
power
· Reflected RF power readings.
· VSWR ratios.
· Convenient control for easy operation.
Explanation of Features:
1. Power Switch
2. 0.96" O-LED Display
3. Menu.
4. Peak/Avg
5. Charger LED
6. 5V Charger in Type -C
7. ANT Connector : Coax connector to 50 Ohm antenna system.
8. TX Connector : Coax connector to transmitter 50 Ohm RF output.
9. Model Detail & Frequency Range
Explanation of display
1. MODEL
2. Battery Level
3. Forward watt
4. Forward watt
5. Version
6. SWR
7. Reflected watt
Menu
1. Mode: Power on for : Normal /Peak
2. BEEP : ON/OFF
3. AUTORESET : OFF ~1~30sec.
4. EXIT
5. SAVE & EXIT
Instruction Manual
Display
MENU
SW-28 V.S.W.R. & Power Meter
CAUTION
1. Since the meter movement is very sensitive, avoid excessive vibration or mechanical shock to the unit.
2. The absolute maximumpower that should be applied to the meter is 120W.
3. The transceiver and antenna connections to the meter must never be reversed.Always observe the correct connections to the transmitter and the antenna .
4. The meter has been carefully calibrated at the factory. Tampering with any of the internal circuitry or sensors may cause damage and will degrade the
accuracy of the meter.
5. Do not expose the meter to excessive temperatures, high humidity, or strong magnetic fields.
Understanding SWR Meters
An SWR (Standing Wave Ratio) meter is an instrument used to measure the amount of reflected power (power coming back from the antenna and/or
transmission cable) to the transmitter. For a transmitter to provide all the power to an antenna, the antenna needs to be resonant and the transmission cable
(coax) has to introduce minimum loss. In a perfect scenario, in an efficient antenna system, all the power outputted from the transmitter makes it into the
atmosphere. Both the coax and the antenna, if not tuned right will induce losses. These losses will not make it out to the air but come back to the transmitter
in the form of "standing waves".
SWR is the ratio of the forward power vs the reflected power. A perfect antenna system will show 100% forward power and 0% reflected power and is referred
to as 1.0:1 which is hard to maintain. Typically a 1.1:1 is ideal and 1.2:1 is average. Anything over 1.5:1 is suspect and needs troubleshooting or tuning. 2:1 is
unacceptable and could damage the transmitter if it doesn't have reflected power protection (foldback) circuitry. A 1.0:1 is 100% efficiency to the atmosphere.
A 1.1:1 is 0.2366% loss, a 1.2:1 is 0.826% loss, a 1.5:1 is 4% loss, and a 2:1 is 11.1% loss of power.
Typically, an SWR meter is placed between the transmitter and the antenna usually at he output of
the transmitter as shown below.
Unfortunately you cannot tell if a problem is in the antenna or coax (transmission line) if it is
placed at the output of the transmitter shown above. Placing the SWR meter at the output of the
transmitter may not necessarily show accurate reflected power since losses in the coax can show
up as a decrease in reflected power. Also if there is high SWR, it can show a high false reading of
output power from the transmitter.
To accurately measure output power of transmitter you must place the SWR
meter between a good 50 ohm purely resistive "dummy" load and the transmitter as shown
below. Accurately note the power RF out first. Be aware that some SWR meters cannot
accurately measure power output. Just relative output for indicating reflected power.
&
· O-LED
· /
·
·
·
50
SWR
使用说明书
SW-28 驻波比
驻波比驻波比
驻波比 ＆
＆＆
＆ 功率计
功率计功率计
功率计
1.
2. 120W
3.
4.
V.S.W.R. /
100% 0% 1.0:1 1.1:1
1.2:1 1.5:1 , 2:1
1.0:1 100%
1.1:1 0.2366% 1.2:1 0.826%
1.5:1 4% 2:1 11.1%
* , ,
50
~
~
~
~
:
, PTT
/
