Ametek peel 3 Handheld 3D Scanners ユーザーマニュアル

peel 3

English

Français

Español

Deutsch

Italiano

Portugês

日本語

한국어

中文

peel 3

User Manual

Scanner peel 3

Document Version: p3-2209-001

Contents

Copyright Notice 3

About this Manual 4

Safety symbols 5

Information symbol 5

Important Safety Information 6

Product 6

Modification of the product 6

Hardware and Components 7

peel 3 7

Package contents 7

Optional Accessories and Parts 9

Specifications and Technical Characteristics 10

peel 3 scanner 10

Computer 11

Important Usage Information 12

peel 3 scanner usage 12

Scanning using the texture cameras (flashing pattern) 12

Cleaning 13

Installation and Connection 14

To install the software 14

To connect the scanner 14

To disconnect the scanner 15

Using peel 3 16

Touch screen 16

Operating principles 17

Calibration 18

Calibration plate usage 18

Configuration 18

Object preparation 18

Acquisition rules 18

Service and Maintenance 19

Damage requiring service 19

Safe disposal 19

Troubleshooting 20

Power 20

Scanning 20

Other 20

Warranty and Liability 22

Resources 23

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 2 of 23

Copyright Notice

IMPORTANT

No part of the contents of this User Manual may be reproduced or transmitted in any form or by any

means without the written permission of Creaform.

Creaform takes no responsibility if errors or inaccuracies were to appear in this document.

Other marks are the property of their respective owners.

peel 3 User Manual version p3d-2203-001

Last modified in September 2022

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 3 of 23

About this Manual

Thank you for purchasing a peel 3 scanner!

The peel 3 scanner is a handheld 3D scanning device. It has been designed to scan objects without the

need for a complex setup.

CAUTION:

Before using the peel 3 scanner, it is important to carefully read this document and

any other documents mentioned in reference to its usage and maintenance of its

accessories. Users are required to familiarize themselves with the device in addition

to following the information provided in the manual.

Make sure to retain this User Manual for future reference.

In this manual, the words "scanner" or "device" refer to the peel 3 scanner.

Other marks are the property of their respective owners.

Refer to the relevant user manual for information about equipment provided by

suppliers other than Creaform.

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 4 of 23

Safety symbols

Throughout this manual, when necessary, safety symbols are used to inform of potential hazards, how to

remain safe and/or the possible consequences if not avoided.

CAUTION: Indicates a hazard with a low level of risk which, if not avoided, could

result in minor or moderate injury.

WARNING: Indicates a hazard with a medium level of risk, if not avoided, could

result in moderate or serious injury.

DANGER: Indicates a hazard with a high level of risk which, if not avoided, will

result in severe injury or death.

Information symbol

Some information given is important and must be closely followed.

Provides information or recommendations on how to use the device correctly.

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 5 of 23

Important Safety Information

Product

VOLTAGE:

The power adapter should be operated only from the type of power source

indicated on the marking label.

WARNING:

Use the product in accordance with all safety rules and operating instructions.

This product is not indented to be used by children or persons with disabilities

otherwise properly trained.

Do not use the product under the influence of drugs, alcohol, medication or while

fatigued.

Do not use the product if the start button is defective or if the electrical

components show signs of a defect. If so, contact the Customer Support

immediately.

Shut down the product immediately if you feel any discomfort.

Do not place on an unstable surface; the product may fall, causing serious injury to

a child or adult, as well as being damaged.

Modification of the product

CAUTION:

Any alteration or modification of the product may pose a danger to the user and is

therefore prohibited.

Do not introduce foreign objects into the device.

Only use the device with the original power supply provided.

Any modification of the product by the user is not recommended and any

consequences will not be covered by Customer Support services or product

warranty.

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 6 of 23

Hardware and Components

peel 3

Package contents

1 x EPP (expanded polypropylene) case

1 x scanner

1 x power supply

1 x power adapter

1 x USB 3.0 cable - 4 m

1 x calibration plate

2 x boxes of targets

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 7 of 23

DANGER:

Choking hazard

Plastic bags can be dangerous. To avoid danger of suffocation, keep bags away

from babies and children.

Positioning targets and small pieces must be kept out of reach of children.

Keep foam and packaging after opening. If necessary, it will be needed to ship the

scanner and/or accessories back for repairs.

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 8 of 23

Optional Accessories and Parts

Only use recommended accessories provided by Creaform.

To order accessories or parts, visit the e-store on the Customer Portal.

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 9 of 23

Specifications and Technical

Characteristics

peel 3 scanner

Infrared IR-A

Projector wavelength 850 nm

Ring light geometry wavelength 820-880 nm

Ring light texture wavelength 400-700 nm

Weight 950 g

Power supply Input 100-240 V ~ 50-60 Hz 1.5 A

Operating temperature 5 to 40 °C

Storage temperature 5 to 55 °C

Operating relative humidity 10 to 90 % non-condensing relative humidity

Compliance CE, FCC, CFR, IP50, WEEE

Dimensions 79mm X 304mm X 150mm

nm: nanometers

Laser label

The laser label reads:

CLASS 1 LASER PRODUCT / IEC 60825-1:2014

850nm / avg ˂ 2.9mW / ˂ 0.2mJ - 3.5 ms / 15.1 Hz max

Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 6082 5-1 Ed.3., as described in Laser Notice No. 56, dated May 8, 2019

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 10 of 23

Computer

Minimum requirements Recommended specifications

Processor (1) Intel Core i7 (6 cores) - 2.5 GHz or

more Intel Core i7 (8 cores) - 2.5 GHz or

more

Operating system (2) Windows 10 (64 bit) (3)(4)

Graphics card (5)(6) 6 GB, openGL 4.5 and higher NVIDIA RTX 3070 (8GB) or better,

OpenGL 4.5 and higher

Memory 16 GB 32 GB

Hard drive Solid-state drive (SSD) with at least

200 GB of free space 512 GB SSD

Display 1920 x 1080

USB 3.0 ports 1 X USB 3.0+ 2 X USB 3.0+

(1) Processor must support AVX2 instructions.

(2) 32-bit OS are not supported.

(3) Windows 10 version 1909 or higher.

(4) .NET Microsoft Framework version: 4.7.2

(5) GPU memory requirements are proportional to the amount of data collected in a single-scan

session. Scanning large parts with higher resolution may exceed the recommended specs and

require merging scans.

(6) Only NVIDIA graphic cards with compute capability 6.1 are supported. Recommended NVIDIA

driver version: 465+

Large scans with high resolution will require more RAM and GPU.

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 11 of 23

Important Usage Information

To use the peel 3 scanner, no particular knowledge about 3D measuring systems is required.

peel 3 scanner usage

Always use the device in a clean and dry environment.

Avoid direct lighting on the optical parts.

Always store the devices following these conditions:

Storage temperature: 5 to 55 °C

Operation temperature: 5 to 40 °C

Humidity: 10 to 90 % non-condensing relative humidity

Avoid magnetic or electric fields: they can cause permanent damage to the scanner.

If you do not intend to use the scanner for a long time, place it in its case following the storage

conditions.

Scanning using the texture cameras (flashing pattern)

DANGER:

Risk of seizures

Some people may experience seizures when exposed to certain visual images,

including flashing lights or patterns. These seizures may include symptoms such as

lightheadedness, altered vision, eye or face twitching, jerking or shaking of arms or

legs, disorientation, confusion, or momentary loss of awareness. Immediately stop

using the scanner and consult a doctor if you experience any of these symptoms

while using this device.

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 12 of 23

Cleaning

CAUTION:

Risk of injury

Never tamper with any product of Creaform. Always refer to qualified personnel at

Customer Support.

1. Unplug the scanner from the wall outlet before cleaning.

2. To clean the device's non-optical surfaces, use a soft cotton cloth with a small amount of water or

a soapy solution. Do not use solvent to clean the device. Do not use soap or solvent on the

optical parts of the device (lenses, lights).

3. Spray dry air to remove any particles that may scratch before cleaning the camera lenses and

lights with a damp cloth such as a non-abrasive optical towel or a microfiber cloth.

Never use chemically treated cloths, moistened disposable wipes or volatile

solvents such as paint thinner.

Do not use liquid or spray aerosol cleaners.

Opening or modifying the scanner will result in loss of warranty.

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 13 of 23

Installation and Connection

To install the software

The software can be installed on a computer with the specifications required by Creaform.

1. Download the software installation file.

2. Double-click the .exe file.

3. Click Next and Install to install all available features.

4. Click Finish to finalize the software installation.

5. Follow instructions and make sure the software license is activated.

The scanner must be connected according to the following procedure to guarantee

its physical integrity and to avoid any damage.

To connect the scanner

VOLTAGE:

Handle the scanner's power cord with care.

Do not disconnect the scanner by pulling on the wire, and do not carry the scanner

by the cord.

Keep the cord away from materials or tools that could damage it (e.g., chemical

products, cutting tools, heat, etc.).

Do not allow the electrical wire to be pinched or twisted.

Always disconnect the scanner before storing or when it is not in use or under

supervision.

Please follow the safety maintenance recommendations from the manufacturer.

DANGER:

Electric shock hazard

Do not use the products near water, in a moist environment or in rain, snow, etc.

Do not immerse the products.

Any alterations or modifications of the products may pose a danger to the user and

are therefore prohibited.

The power cord is equipped with a polarized, 2-prong plug. For safety, it fits into

the power outlet one way. Never circumvent this safety feature.

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 14 of 23

1. Plug the power supply cable into an electric source.

2. Connect the power supply cable to the USB 3.0 cable.

3. Connect the USB 3.0 cable to the computer.

4. Connect the other extremity of the USB 3.0 cable to the scanner.

5. Connect the power cable to the scanner.

To disconnect the scanner

1. Unplug the power and the USB cables from the scanner.

2. Disconnect remaining cables as desired afterwards.

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 15 of 23

Using peel 3

Before using the peel 3 scanner, make sure to read the entire User Manual with

special attention to Important Safety Information and Important Usage

Information sections.

Used with the scanner, the peel.OS software provides powerful tools and features

to finalize scans and speed workflows.

Touch screen

The scanner has a touch screen that allows users to interact with the scanner's functions with their

fingertips.

Button Description

Shutter time

Zoom in/Zoom out/Reset zoom

Start/Pause (Scan)

Scanner position lost

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 16 of 23

LED color chart

Scanner position: too close

Action: move back

Scanner position: too far

Action: move forward

Scanner position: correct

Operating principles

Geometry-based positioning

The scanner requires geometry in order to position itself. The projector emits a white light stripe pattern

on the object. The pattern distortion on the object is recorded by cameras. The acquisition is made over

the light pattern and the geometry information collected is used to build the surface with real-time

positioning.

Intelligent hybrid positioning

The scanner detects positioning targets on and around the object. Intelligent hybrid positioning

combines the positioning targets provided with the geometry information in order to provide more

accurate results. This feature always uses all the information available, the geometry and positioning

targets, to provide positioning. It does so while ensuring that sufficient data is available to guarantee

accuracy. The built-in intelligence also prevents the acquisition of inaccurately positioned frames.

Texture positioning

The scanner acquires and detects the object's texture with its digital color camera.

It is recommended to keep the laptop plugged into an external power source

rather than relying on the laptop's internal battery because of the intense power

requirements of the scanner and high processing workload.

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 17 of 23

Calibration

The calibration process is self-guided. To calibrate the scanner, follow the steps indicated at the

calibration step in the software.

Calibration plate usage

1. Open the case cover.

2. Lay calibration plate case on flat surface.

3. Calibrate following instructions carefully.

4. Close the cover and store in the case after use.

The calibration plate is a crucial part of the system. A damaged plate may prevent

the calibration optimization and affect the scan results.

Always leave the calibration plate in its case.

Do not touch the targets on the plate.

Do not scratch the plate.

Do not heat or store in hot environments.

Configuration

The configuration process is self-guided. To configure the scanner, follow the steps indicated at the con-

figuration step in the software.

Object preparation

In order to provide better scan results, the object to scan must be prepared following some simple steps.

The scanner self-positions itself based on the object geometry. No positioning targets are required for

objects featuring sufficient geometric information. In the case of flat or shiny surfaces, positioning

targets will provide better scan results.

Acquisition rules

The field of view is the image scope that the scanner can acquire during the scanning process. Any data

out of the scanner's field of view will not be acquired. For better surface results and to ensure optimal

field of view, a certain stand-off distance must be respected. The software will guide you through the

scan process.

peel 3User Manual version p3d-2209-001 (last update:2022-09-13)

Page 18 of 23

Service and Maintenance

Damage requiring service

Disconnect the scanner from the wall outlet and computer.

Refer to Creaform Customer Support under the following conditions:

The power cord or the plug is damaged.

Liquid has been spilled on the scanner.

The scanner has been exposed to rain or water.

The scanner has been dropped and is damaged or does not work properly.

Any other circumstance that may require the intervention of qualified personnel for maintenance

or repair.

See Resources for contact information.

Safe disposal

Dispose of the products (scanner, targets, accessories) and packaging appropriately in

accordance with local laws and regulations.

Contact your local authorities for any product specific treatment and waste management

information.

peel 3User Manual version p3d-2203-001 (last update:2022-09-13)

Page 19 of 23

ページを読み込んでいます...

Ametek peel 3 Handheld 3D Scanners ユーザーマニュアル

その他の書類