Pro'sKit TE-8202F-W 取扱説明書

TE-820 series

Optical Fiber Fusion Splicing Machine Kit

User’s Manual

1st Edition, 2023

1

Please read this Operation Manual carefully before operating the

equipment. Comply with all safety procedures and warnings in this manual.

Keep this manual properly in a safe place.

CONTENTS

WARNINGS AND CAUTIONS FOR SAFE OPERATION

1-5

PRODUCT INTRODUCTION

1. SPECIFICATIONS

2. OTHER NECESSARY ACCESSORIES FOR FUSION

SPLICING OPERATION

3. DESIGNATION OF COMPONENTS OF OPTICAL

FIBER FUSION SPLICER

6-8

MAIN POINTS OF FUSION SPLICING PROCEDURES

9-11

BASIC OPERATIONS

1. POWER CONNECTION

2. TURNING ON POWER OF OPTICAL FIBER FUSION

SPLICER

3. LAYING OPTICAL FIBER

4. SPLICING OPERATION

5. TAKING OUT OPTICAL FIBER AND HEAT IT UP

6. HOW TO USE FIXTURE

11-13

MAINTENANCE OF FUSION SPLICING QUALITY

1. CLEANING AND CHECKING BEFORE FUSION

SPLICING

2. REGULAR CHECKING AND CLEANING

13-16

MENU

16-39

QUESTIONS AND TROUBLE SHOOTING

1. TURNING ON POWER OF OPTICAL FIBER FUSION

SPLICER AND POWER SUPPLY

2. FUSION SPLICING OPERATIONS

3. HEATING OPERATIONS

40-47

GUARANTTE AND CONTACT

1. GUARANTEE

2. CONTACT

DESIGN AND CHANGE

47-48

48

2

The Optical Fiber Fusion Splicer is designed for the optical quartz glass

Fiber used in the communications, except which it cannot be used to splice

any other substances and for other applications.

Considering the user’s personal safety, here we provide the user with a lot

of safety cautions，because it is possible to result in electric shock, fire

and personal injury if the user improperly uses the Optical Fiber Fusion

Splicer.

Please read seriously, by all means, this Operation Manual before

operating the equipment.

Comply with all safety requirements and warnings in this manual.

Keep this manual properly in a safe place.

In case of meeting a failure, please stop using the equipment, and

contact us as soon as possible

Keep this manual properly in a safe place, so as to refer to it in the

future.

WARNINGS AND CAUTIONS FOR SAFE OPERATION

It is necessary to immediately turn off the power switch of the Optical Fiber

Fusion Splicer ; pull the AC power cord out of the AC power outlet; and take

out the storage battery from the Optical Fiber Fusion Splicer, in case of

meeting the following failures:

⚫ Smoke, peculiar smell, abnormal sound or heating abnormalities;

⚫ Liquid or foreign objects into the equipment;

⚫ The Optical Fiber Fusion Splicer has been damaged or broken.

If the user has not timely adopted measures to solve failures of the Optical

Fiber Fusion Splicer in case of meeting these failures, it may cause the

equipment scrap, electric shock, fire or personal injury or even death.

The AC-DC adapter and battery charger of the Optical Fiber Fusion Splicer

can only use an AC power source (100V-240V AC, 50hz-60hz). If the user

uses the improper AC power source, it may possibly lead to smoke, electric

shock, equipment damage, and even cause the fire or personal injury or

death. (Note: Usually, AC generators output abnormal high pressure and

irregular frequency, so that it is necessary to measure generator’s output

voltage value with the ammeter before connecting the AC power cord.

Abnormal high pressure or frequency can lead to smoke, electric shock,

equipment damage, and can even cause fire or personal injury or death.

Make sure the generator’s regular check and maintenance.

3

Please use the specific AC-DC adapter. If you use the inadequate AC-DC

adapter, it may possibly lead to smoke, electric shock, equipment damage,

and cause the fire or personal injury or even death.

Please use the specific batteries. Only the batteries supplied by the

manufacturer are allowed to be used for the equipment. Please use the

specific battery charger to charge the batteries. If you use other batteries or

battery chargers, it may possibly lead to smoke, electric shock, equipment

damage, and cause the fire or personal injury or even death.

Don’t make bold to disassembly or modify the Optical Fiber Fusion Splicer,

the specific AC adapter, or the batteries, esp., any electronic and

mechanical devices (fuses or safety switches) inside the equipment can not

be removed or bridged. Any improper maintenance may possibly lead to the

damage of the Optical Fiber Fusion Splicer, and even cause electric shock,

the fire or personal injury or death

It is prohibited to use the Optical Fiber Fusion Splicer in the flammable liquid

or gas environments, where the discharge of the Optical Fiber Fusion

Splicer may cause the fire or explosion.

Do not use the compressed or canned air cleaner to clean the Optical Fiber

Fusion Splicer. Otherwise the arcing generated by splicing will ignite the

residual flammable matter.

Don't use the Optical Fiber Fusion Splicer in the environment of high

temperature or nearby the high temperature object, and also in the place

where there are too much dusts or higher humidity, otherwise it may possibly

lead to equipment damage, cause the fire, get an electric shock, degrade

the equipment performance, and cause the worse splicing loss.

Please don't use the wet hand to contact the Optical Fiber Fusion Splicer,

the AC power cord and AC power plug; otherwise it may possibly cause the

risk of getting an electric shock.

When the surface of the Optical Fiber Fusion Splicer is vapor-condensed,

please don’t operate the Optical Fiber Fusion Splicer, otherwise it may lead

to electric shock or equipment damage.

When the Optical Fiber Fusion Splicer is operating, please don't touch the

electrode, otherwise the high pressure and high temperature generated by

electrode discharge may cause severe electric shocks and burns (Before

changing the electrode, you must firstly turn off the power supply of the

Optical Fiber Fusion Splicer, remove the batteries, and pull out the AC

power cord.)

4

Do not let the DC input ports of the Optical Fiber Fusion Splicer be short-

circuited. The excessive current may lead to personal injury, smoke, electric

shock or equipment damage.

Do not use any chemical substances other than alcohol to clean such

devices as the objective lens, the V-shaped groove, reflecting mirror, LCD

screen, etc., of the Optical Fiber Fusion Splicer. Otherwise it will cause the

imaging to be unclear, with stains, corrosion and damage.

The Optical Fiber Fusion Splicer does not need any lubricant, lubricating oil

or grease, which will reduce the performance of the Optical Fiber Fusion

Splicer and possibly damage the Optical Fiber Fusion Splicer.

For the Optical Fiber Fusion Splicer having passed through the accurate

adjustment and calibration, don't subject it to strong shock or collision,

otherwise this may possibly cause damage to the equipment. Please use

the provided case to transport and store the Optical Fiber Fusion Splicer, so

as to effectively protect it from strong vibration or collision.

Don’t let the Optical Fiber Fusion Splicer be positioned at an unstable or

uneven place, otherwise it may possibly move and lose its balance and fall

over, causing the equipment damage and the personal injury.

For the heat-shrinkable sleeve during heating or just at the end of being

heated, please don’t touch it, because at this time, the temperature of its

surface is very high, if you touch it, this may possibly cause burns to you.

When you need to bring the portable Optical Fiber Fusion Splicer with

shoulder-strap carrying case, please check whether the shoulder strap and

hook are intact to you or not. If you use a damaged shoulder strap, it may

possibly cause the shoulder strap to be ruptured or escape from the hook,

resulting in the personal injury or the equipment damage.

The Optical Fiber Fusion Splicer must be maintained and debugged by a

professional technician or an engineer. The incorrect maintenance for it may

possibly cause the fire and the electric shock. If the Optical Fiber Fusion

Splicer fails, please contact a service center.

Please use the storage batteries strictly according to the Operation Manual.

The wrong use may cause the battery explosion and the personal injury.

⚫ Do not use certain methods other than those mentioned in the Operation

Manual for battery charging;

⚫ Do not dispose of batteries in fire or incinerator;

⚫ Do not charge and discharge the storage batteries at the place being close

to the fire or under the direct sunlight;

⚫ Do not let the batteries be subjected to the severe shock;

⚫ If the battery leaks, you must handle it with caution, and pay attention to

5

preventing the battery leaking liquid from touching your skin or eyes. In

case that you have accidentally touched the battery leaking liquid, you

must immediately and thoroughly clean the touched parts, and seek

medical care immediately. At the same time, please properly handle the

leaking battery and notify the maintenance service center for solving the

related issues.

⚫ In case of charging the batteries, it is not allowed that the batteries will be

stacked up on top of the AC-DC adapter or charger.

Please correctly use the electrodes according to the Operation Manual.

⚫ Use only the specific electrodes

⚫ Correctly replace the electrodes

⚫ The electrodes must be replaced in pairs

If the above instructions are ignored, it may cause the abnormal

discharge of the Optical Fiber Fusion Splicer, the splicing performance

degradation or even damage to the equipment.

The manufacturer or Seller will not assume the responsibility for the

Buyer’s or user’s personal injury and losses of the articles or

equipment caused by that the user ignores the warning and uses or

repairs the Optical Fiber Fusion Splicer incorrectly.

Recycling and Disposal

EU countries:

According to the EU’s European Parliament’s implementation

standard:2012/19/EU, in order to use the new resources and make the

number of buried waste to be minimized, the reusable and / or recycling

electronic components and materials have been identified and recognized. If

you are in the EU countries, please do not use this product as unsorted

municipal living solid waste to be discarded. Please contact your local

relevant agencies.

Other countries:

For recycling this product, please firstly disassemble it, and then classify each

part according to different materials, and keep to the relevant local regulations

related to the recycling.

6

1. Specifications：

Model no.

TE-8202A

TE-8202F

TE-8202A-W

TE-8202F-W

Applicable fiber

SM，MM，NZDS, EDF

Average splice loss

0.02dB(SM)，0.01dB(MM), 0.04dB(NZDS), 0.04dB(ED)

Splice time

10s (SM)

Suitable for cutting

optical fiber length

10～16mm

Suitable for optical

fiber core

Cladding diameter:80-150μm,

Coating diameter:100-1000μm

Return loss

≧60dB

Fiber image

magnification

Tension test

2.0N(200gf)(standard)

Splice program

50 groups

Electrode life

6000 times

Protection sleeve

length

20mm~60mm

Storage of fusion

splice result

10000 groups of splice results

Storage of fusion

splice image

100 groups of splice images

Monitor

5 “high resolution colorful LCD

Communication port

Micro USB

Working light

1 LED light

Power indication

4 led indication

Operation condition

Temperature: -10~+50℃

Humidity：0~95%RH

altitude： 0~5000m

Standard plug

A type

F type

A type

F type

Package

1. Machine x 1pc

2. Fiber Cleaver x 1pc

3. Fiber Stripper x 1pc

4. AC Adaptor x1pc

5. Battery x1pc

6. Spare

Electrodesx1set

7. Protection sleeve

(60mm)x 25pcs

8. Liquid dispenser bottle

1. Machine x 1pc

2. AC-DC Adaptor x1pc

3. Battery x1pc

4. Spare Electrodes x 1set

5. Protection sleeve(60mm)

x 25pcs

6. Cooling Tray x 1pc

7. USB cable x1pc

8. Operation Manual x 1pc

9. Carrying Belt x 1pc

7

x 1pc

9. Cooling Tray x 1pc

10.USB cable x1pc

11.Operation Manual x

1pc

12.Carrying Belt x 1pc

13.Carrying Case with

Carrying Strap x 1pc

14.Disk (with

communication program,

driver and Instructions)

10. Carrying Case with

Carrying Strap x 1pc

11. Disk (with communication

program, driver and

Instructions)

Power supply

Lithium battery: 10.95V/6Ah

Adapter: Input AC 100~240 50/60Hz; Output: DC15V/5A

Dimension

(W x D x H)

155x145x145mm

Weight(approx)

1.98Kgs (include battery) , 1.6Kgs(not include battery)

TE-8202A / TE-8202F

TE-8202A-W / TE-8202F-W

2. OTHER NECESSARY ACCESSORIES FOR SPLICING OPERATION

1. Optical Fiber heat-shrinkable sleeve (20~60mm, not include)

2. Alcohol Without Water(Purity: >99%)(not include)

3. Tissue, Gauze or Skim Cotton Cloth (not include)

8

3. DESIGNATION OF COMPONENTS OF OPTICAL FIBER FUSION

SPLICER

9

MAIN POINTS OF FUSION SPLICING PROCEDURES

1. How to Get Small Splicing Loss

1-1. Necessary Regular Cleaning Jobs

 To Clean V-Shaped Groove

 To Clean Reflecting Mirror

 To Clean Optical Fiber Pressure Head

 To Clean Objective Lenses

In case of cleaning Objective Lens，it is unnecessary to remove

needle electrodes

1-2. Selection/Usage of Appropriate Splicing Modes

Please select the appropriate splicing modes according to different

sorts of the Optical Fibers.

1-3. Equipment Clean-up before Each Fusion Splicing Operation

 To clean the blades of Optical Fiber Stripper.

 To clean the rubber pad and blades of the Optical Fiber Cleaver.

1-4. FUSION SPLICING PROCEDURES

 Make sure that the coating residue and other contaminants on

the optical fiber will have been removed after stripping the optical

fiber.

 Please use the pure alcohol with a concentration of more than

99%.

 Do not let the well-cut end of the optical Fiber touch any object or

be contaminated.

 Please put the end of the optical Fiber at the place between the

edge of the V-shaped groove and the center of electrode.

 Please put the optical Fiber rightly on the bottom of the V-shaped

groove.

 Make sure the correct cut length. If the cut length is too short, the

optical Fiber’s coating edge may possibly encounter the V-

shaped groove, so that two optical fibers can not be, in the

discharge process, fully close to each other, resulting in

undesirable loss of fusion splicing.

 Do not tight the optical fibers, otherwise, two optical fibers can

not be, in the discharge process, fully close to each other,

resulting in undesirable loss of fusion splicing.

 Please check the cutting angle and shape of the optical fiber’s

end face. The optical Fiber’s cutting angle will affect the fusion-

splicing quality, and a large cutting angle will increase the loss of

fusion splicing.

10

 It is possible to observe the discharge from the display screen. If

the discharge "vibration" or "flickering light" are being observed,

the discharge may be unstable at this time and will result in

adverse loss.

 In case of heating, the Optical Fiber heat-shrinkable sleeve shall

be placed in the center of the heater, so as to avoid uneven

heating and lead to additional losses.

2. Power Supply

Please only use the AC-DC Adaptor provided by the manufacturer.

Please only use the Storage Battery and Battery Charger provided by

the manufacturer.

2-1. Avoidance of Damage to AC Adapter

 The AC generators may possibly produce abnormal output of AC

high voltage or irregular frequency.

 The abnormal high voltage and frequency output from the

generator may possibly lead to smoke, electric shocks and

damage to the equipment, and even cause the fire, the personal

injury or death. So, before connecting the AC power supply, you

must use a multimeter to measure the generator output voltage.

2-2. Storage Battery

 Even if the storage battery is not used, its capacity will also

gradually go down along with the time goes, and if it is fully

discharged, it would never be able to charge into the electricity.

So, if it will be stored for a long time or it has been used, please

charge it in time.

 If it is necessary to store a pack of storage battery for a long time,

and no matter how much electricity quantity it has been charged

before, you should charge it every six months.

 For operating/charging/longtime storing the storage battery,

please refer to the conditions as below:

11

Operating: -10 ℃ ~ +50 ℃

Charging: 0 ℃ ~ +40 ℃

Longtime Storing: +20 ℃ ~ +30 ℃

BASIC OPERATIONS

1. POWER CONNECTION

OPTICAL FIBER FUSION SPLICER provide two power-supply modes:

① Storage Battery; ② AC-DC Adapter. Please make sure that

OPTICAL FIBER FUSION SPLICER shall be turned off .in case of

operating it.

1-1. Insertion of the Storage Battery

Insert the storage battery into the battery slot until it is properly in

place.

1-2. Removal of the Storage Battery

Using one hand to press and hold the release button and also

support the edge of OPTICAL FIBER FUSION SPLICER, and the

other hand to push the storage battery out.

1-3. Connection of the AC-DC Adapter

Put the plug into socket on the back of device.

1-4. Disconnection of the AC-DC Adapter

Pull out the plug.

2. TURNING ON POWER OF OPTICAL FIBER FUSION SPLICER

Press power button to switch ON/OFF device.

3. LAYING OPTICAL FIBER

1) To open the wind-protector cover and the optical fiber clamp cover;

2) To get the ready optical fiber to be placed in the V-shaped groove,

and make the end of optical fiber be placed at the position between

the edge of the V-shaped groove and the electrode tip;

3) To use fingers to nip the optical fiber, then to close the optical fiber

clamp cover so as to ensure that the optical fiber will not move, and

make sure that the optical fiber will be placed at the bottom of the V-

shaped groove. If the optical fiber is placed incorrectly, please place

the optical fiber over again;

4) To place another optical fiber according to the above step;

5) To close the windproof cover.

12

4. SPLICING OPERATION

4-1.Optional Operation Modes：AUTO/MANUAL

AUTO：By pressing the key, it is able to start the fusion

splicing operation.

MANUAL：For the Manual operation, please refer to the details.

4-2.Optional Types of Optical Fibers: Single Mode (SM) / Multi

Mode (MM) /Non-Zero Dispersion-Shifted (NZDS) / Erbium-

Doped (ED) Optical Fiber

4-3.Pause Functions: Open/Close

Open: After the completion of the core-to-core, press the

key to perform the fusion splicing.

Close: After the completion of the core-to-core, automatically

perform the fusion splicing.

5. TAKING OUT OPTICAL FIBER AND HEAT IT UP

1) Open the heater lid;

2) Open the windproof cover;

3) Open the optical fiber clamp covers at the left and right;

4) Take out the optical fiber and move Optical Fiber heat-shrinkable

sleeve to the splicing point;

5) Place the Optical Fiber heat-shrinkable sleeve in the centre of the

heater and cover the heater lid;

6) Press the HEAT key to heat, the heat indicator will also light up;

7) When the heat indicator goes out and a hint sound appears, the

heating is completed;

8) Turn on the heater lid, and take out the optical fiber to check and

see if the optical fiber contains air bubbles or not;

9) After completing the checks, place the optical fiber in the Cooling

Salver to cool it.

6. How to use fixture

Optical fiber splicing fixture (3-in-1)，support Bare fiber splice，

2mm/3mm Pigtail/simplex optic，0.9mmPigtail/Simplex cable splice and

rubber-insulated wire/Drop cable splice use。

details as follows:( the pictures for reference only)

13

Bare fiber splice

[2mm/3mm]Pigtail/simplex optic

cable splice

0.9mmPigtail/Simplex cable

splice

rubber-insulated wire/Drop cable

splice

MAINTENANCE OF FUSION SPLICING QUALITY

1. CLEANING AND CHECKING BEFORE FUSION SPLICING

The following describes the maintenance checks for the key cleaning

points and the important parts.

1-1.Cleaning the V-Shaped Groove

If there are dusts or contaminations in the V-shaped groove, the

optical Fiber Pressure Head can not suppress the Optical Fiber

correctly, resulting in that the loss of fusion splicing is larger. So, in

regular operation, it is necessary to check more often and clean

regularly the V-shaped groove.

 To open the windproof cover.

 To clean the bottom of the V-shaped groove with a cotton swab

just having had a dip in alcohol (above 99% alcohol), and remove

the excess alcohol in the V-shaped groove with a dry cotton

14

swab.

 If contaminations in the V-shaped groove can not be removed

with a cotton swab just having had a dip in alcohol, you can use

the well-cut end face of the optical Fiber to clean the bottom of

the V-shaped groove, and then repeat the previous step.

 In case of cleaning the V-shaped groove, be careful and don’t

exert an excessive force, so as to avoid damage to the V-shaped

groove.

 Be careful and don’t touch the tip of the needle electrode.

1-2. Cleaning Up the Optical Fiber Pressure Head

If there are contaminations on the Optical Fiber Pressure Head,

the optical Fiber Pressure Head can not suppress the Optical

Fiber normally, resulting in degrading the quality of fusion splicing.

 To open the windproof cover.

 To clean the surface of the Optical Fiber Pressure Head with a

cotton swab just having had a dip in alcohol (above 99% alcohol),

and remove the excess alcohol on the surface of the Optical

Fiber Pressure Head with a dry cotton swab.

1-3. Cleaning the Optical Fiber Cleaver

If there are contaminations on the blades of the Optical Fiber

Cleaver or the rubber pad, the cleaving quality will be degraded,

and lead to dusts on the surface of the optical Fiber, resulting in

the increase of the loss of the fusion splicing. It is necessary to

clean the blades of the Optical Fiber Cleaver. or the rubber pad

with a cotton swab just having had a dip in alcohol (above 99%

alcohol)

1-4. Discharge Tests

Atmospheric environment, such as: temperature, humidity, air

pressure, is constantly changing, so that the discharge

temperature is also changing. Due to the electrode wear, it is

unable to automatically correct the discharge strength caused by

the bonding of the optical Fiber debris. The center of the discharge

sometimes will move to the left or to the right. At this time, it is

necessary to make the discharge tests to solve these problems.

It is also necessary to do discharge tests in case of using the

Optical Fiber Fusion Splicer under the following conditions: such

as ultra-high temperature, ultra-low temperature, very dry, very

wet, electrode degradation, fusion splicing of the heterogeneous

optical Fibers, cleanness, after replacing the electrode, or in the

case that above conditions exist simultaneously.

15

2. REGULAR CHECKING AND CLEANING

In order to ensure the better splicing quality, it is suggested to check

and clean the Optical Fiber Fusion Splicer regularly.

2-1. Cleaning the Objective Lens

If there are contaminations on the surface of the Objective Lens,

the normal location of the observed optical Fiber core may be

affected, resulting in the increase of the fusion splicing loss or poor

fusing splicing, so, it is necessary to regularly clean two objective

lenses, otherwise, the cumulative contaminations are difficult to

remove.

 Before cleaning, please firstly turn off the power supply.

 Using a cotton swab just having had a dip in alcohol (above 99%

alcohol), to gently wipe the surface of the objective lens, starting

the wipe from the middle of the lens to do a circular movement

until the edge of the lens, and repeating several times until there

are no contaminations or stains or stripes. Finally, use a clean

and dry cotton swab to wipe out the residual alcohol on the

surface of the objective lens.

 Be careful and don’t touch the electrode tip in case of cleaning.

 It is recommended to clean the lens in case of replacing the

needle electrode.

2-2.Replacing the Electrode

The electrode will wear in use, and the electrode tip will be

aggregated with silicon oxide, so, to regularly clean the oxide can

effectively extend the life of the needle electrode. It is

recommended to replace the electrode after Optical Fiber Fusion

Splicer has discharged 3000 times. If you continue to use the

electrode, it may most probably lead to have a very large fusion-

splicing loss and reduce the strength of the fusion-splicing points.

Steps of replacement of the needle electrode:

 To turn off the power supply of the Optical Fiber Fusion Splicer.

 To screw out fixing screws, and remove the old needle electrode

suffered from electric shock.

 To use a tissue just having had a dip in alcohol to clean the new

needle electrode, and then install correctly the needle electrode

on the Optical Fiber Fusion Splicer and tighten the fixing screws.

 To turn on the power, and put the prepared fiber into the Optical

Fiber Fusion Splicer to do the discharge tests.

16

MENU

How to Enter and Select Menu

Once the system is “ready”, press “ ” to enter the menu, and press

the keys“▲”，“▼”，“◀” ，“▶” to select Menu，press“ ” to exit.

Screws for Fixing Needle

Electrode

Remove plastic housing

17

Menu for Common Function Menu for Parameter Set Menu for System Debug

Menu for Machine Info Menu for Other Config. Menu for Quick Check

1. Menu: Common Function

1-1. “Arc Test”

In order to ensure the stable fusion-splicing quality, the user

should operate regularly. It is necessary to do arc test in case of

using the Optical Fiber Fusion Splicer under the following

conditions: ultra-high temperature, ultra-low temperature, very dry,

very wet, electrodes degradation, fusion splicing of the

heterogeneous optical fibers, cleanness, or after replacing the

electrode.

The arc test needs to use two optical fibers being ready to be

fusion-spliced, according to the general method of fusion splicing,

these optical fiber should be stripped, cleaved off, and placed on

the fixture. Press to enter arc test program. When seeing

“Place fiber and press Enter” , place the fiber well and press the

18

After arc, a numeric value will be displayed on the screen. If the

value is within the range of 45-65, it means that the arc power is

OK. If the value is less than 45, it means that the arc power is

weak, if more than 65, arc power is too strong

After arc, if shown weak or strong, please press , store the

record , and then do arc test again until shown the proper arc

power value.

1-2. “Language”

Set the Language. (Default English)

19

1-3. “Para Check”

This is an Automatic calibrated program, no need to modify

manually

1-4. “Arc Force”

It is off when use normally

When turned on, it is still work when splicing even if the fiber is

not proper to splice.

1-5.“Cleave Arc”

Clean fiber for Splicing-on-Connector (SOC).

ページが読み込まれています...

Pro'sKit TE-8202F-W 取扱説明書

このマニュアルも適しています

Pro'sKit TE-8202F-W 取扱説明書

他の言語で

関連論文

その他のドキュメント