Dell UPS 5600R クイックスタートガイド

Dellt Line-Interactive Rack UPS

5600W

Getting Started With

Your System

Démarrer Avec Votre Système

Erste Schritte mit Ihrem System

Начало работы c системой

Inicio de su sistema

用 指南

사용자의 시스템 시작하

はじめにおいのシステム

H955N, J731N

K812N

w w w . d e l l . c o m | s u p p o r t . d e l l . c o m

Dellt Line-Interactive Rack UPS

5600W

Getting Started

With Your System

H955N, J731N

K812N

w w w . d e l l . c o m | s u p p o r t . d e l l . c o m

Notes and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your software.

DANGER: A DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING: A WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or

injury.

CAUTION: A CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury or in property damage incidents.

DANGER: Observe the following instruction to help prevent an imminently hazardous situation which, if not

avoided, will result in death or serious injury:

S This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by

AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS

inside the UPS.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their

products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

September 2009

3

System Features

|

System Features

Providing outstanding performance and reliability, the UPS's unique benefits include:

S The UPS filters and regulates incoming AC power and provides consistent power to your

equipment without draining the battery.

S High Efficiency – minimally switched patented topology.

S 4U size that fits any standard 48 cm (19”) rack.

S Start‐on‐battery capability for powering up the UPS even if utility power is not available.

S Extended runtime with an optional Extended Battery Module (EBM).

S Emergency shutdown control through the Remote Emergency Power-off (REPO) ports.

S Two standard communication ports (USB and DB-9 serial port).

S Optional Dell Network Management Card with enhanced communication capabilities for

increased power protection and control.

S Advanced power management with the Dell UPS Management Software for graceful shutdowns

and power monitoring.

S Sequential shutdown and load management through separate receptacle groups called load

segments.

S Firmware that is easily upgradable without a service call.

S Backed by worldwide agency approvals.

4

|

Finding Information

CAUTION: The Safety, Environmental, and Regulatory Information document provides important safety and

regulatory information.

What are You Looking For?

Find It Here

S The user's guide for my UPS

S The user's guide for the Dell Network Management

Card

S Dell UPS Management Software

NOTE: Documentation and software updates can be

found at

support.dell.com.

Dell UPS Disc

S Specifications

S How to configure UPS settings

S How to troubleshoot and solve problems

S How to install REPO control

Dell UPS User's Guide

The user's guide is available on the Dell UPS disc and

on support.dell.com.

S Safety instructions

S Regulatory information

S Recycling information

Safety, Environmental, and Regulatory Information

S Warranty information

S Terms and Conditions (U.S. only)

S End User License Agreement

Dell Warranty and Support Information

S Support information Dell Support Website — support.dell.com

NOTE: Select your region or business segment to view

the appropriate support site.

5

Installation and Startup

|

Installation and Startup

CAUTION: Before performing the procedures in this document, read and follow the safety instructions and

important regulatory information in your Safety, Environmental, and Regulatory Information document.

This section describes the steps to set up your system for the first time.

Unpacking the System

1 Open the outer carton and remove the accessories packaged with the cabinet.

6

|

Installation and Startup

Lifting the Cabinet

CAUTION: The cabinet is heavy (74 kg/163 lb). Lifting the cabinets into the rack requires a minimum of two

people.

1 With one person on each side, carefully lift the cabinet out of the outer carton using the handles

on the cardboard and set it on a flat, stable surface.

2 Discard or recycle the packaging in a responsible manner, or store it for future use.

7

Installation and Startup

|

Identifying the UPS

This section shows a front and rear panel of the Dell Line-Interactive Rack UPS.

On/Off Button

LCD Panel

Scroll Button (Down or Forward)

Select Button

Scroll Button (Up or Back)

Figure 1. The Dell Line-Interactive Rack UPS Front Panel

UPS

Communication Bay

Input Terminal

Block

USB Port

Four IEC 320-C19

Receptacles

(Load Segment 1)

REPO Ports

RS-232 Port

Two NEMA L6-30R

Receptacles

(Load Segment 2)

EBM Connector

Output Circuit

Breaker

Ground Screw

Figure 2. 5600W, 208V Rear Panel

8

|

Installation and Startup

Six IEC 320-C13 Receptacles

(Load Segment 2)

REPO Ports

Four IEC 320-C19 Receptacles

(Load Segment 1)

EBM Connector

Output Circuit Breaker

UPS

Communication Bay

USB Port RS-232 Port

Input Terminal Block

Ground Screw

Figure 3. 5600W, 230V Rear Panel

9

Installation and Startup

|

Rackmount Setup

CAUTION: The cabinet is heavy (74 kg/163 lb): 1) Dell strongly recommends removing the battery tray from the

UPS before lifting. 2) Lifting the cabinets into the rack requires a minimum of two people.

CAUTION: Removing the batteries should be performed or supervised by personnel knowledgeable about

batteries and the required precautions. Keep unauthorized personnel away from batteries.

Removing the Battery Retaining Bracket

1 Loosen the thumbscrew on the battery retaining bracket and remove.

10

|

Installation and Startup

Removing the Battery Trays

2 Pull the battery trays using the plastic tabs and remove the battery trays.

11

Installation and Startup

|

Installing the Rails

NOTE: The instructions are the same for square-hole racks and unthreaded, round-hole racks. The rails fit both

rack styles. The square-hole rack is shown in the illustrations.

3 Select the proper holes in the rail for positioning the UPS in the desired location in the rack.

The rails should be located at the bottom of the 4U space allocated for the UPS or 3U for the

EBM.

4 Position the end of the left and right rails labeled FRONT facing inward.

12

|

Installation and Startup

5 Attach the rails to the rack:

Engage the back end of the rail until it fully seats on the vertical rack flange and the hook latch

locks in place.

Pull the rail toward the front.

Push the front end of the rail until it fully seats on the vertical rack flange and the hook latch locks

in place.

Installing the Cabinet

6 Slide the cabinet into the rack. Repeat for any additional cabinets.

13

Installation and Startup

|

Securing the Cabinet

7 Secure the front of the cabinet to the rack using the thumbscrews on the mounting brackets.

Tighten by hand; do not use power tools. Repeat for any additional cabinets.

Installing the Battery Tray

8 Install the UPS battery trays.

14

|

Installation and Startup

Replacing the Battery Retaining Bracket and Connecting the Internal Battery Connectors

9 Replace the battery retaining bracket.

10 Tighten the thumbscrew.

Torque the screw to 0.7 Nm (6.2 lb in).

NOTE:

A small amount of arcing may occur when connecting the batteries. This is normal and does not damage

the unit or present any safety concern.

11 Connect the internal battery connectors and attach to the battery retaining bracket between the

two studs.

15

Installation and Startup

|

Installing the UPS Front Cover

12 Install the UPS front cover.

Connecting the Equipment

13

If you plan to use Dell UPS Management Software, connect your computer to the USB port using

the supplied cable.

14 If your rack has conductors for grounding or bonding of ungrounded metal parts, connect the

ground cable (not supplied) to the ground bonding screw.

15 If an emergency power-off (disconnect) switch is required by local codes, see “Installing Remote

Emergency Power-off” (REPO) in the Dell Line-Interactive Rack UPS 5600W User's Guide.

16 Plug the equipment to be protected into the UPS output receptacles, but do not turn on the

protected equipment.

NOTE:

Verify that the total equipment ratings do not exceed the UPS capacity to prevent an overload alarm.

16

|

Installation and Startup

Hardwiring the UPS Input

WARNING: Only qualified service personnel (such as a licensed electrician) shall perform the electrical

installation. Risk of electrical shock.

The UPS requires a dedicated branch circuit that meets the following requirements:

S 5600W/208V models only: 40A 2-pole circuit breaker to provide short circuit and overcurrent

protection

S 5600W/230V models only: 32A for Europe (or 35A for North America) 2-pole circuit breaker to

provide short circuit and overcurrent protection

S The protection device requires a two-pole disconnection device between the UPS output and the

load (see Figure 4)

S The breaker must be wall-mounted and be readily accessible to the operator

S For Europe, the breaker must meet the IEC/EN 60934 standard and have a contact air gap of at

least 3 mm

S 200–240 Vac

S Single-phase

- 5600W/208V model is phase-to-phase

- 5600W/230V model is phase-to-neutral

S 50/60 Hz

S Flexible metal conduit (recommended for ease of service and maintenance)

AC Mains

Wall

2-pole

Breaker

UPS

Line

Neutral

Figure 4. Circuit Breaker Diagram

17

Installation and Startup

|

Removing the Terminal Block Cover

1 Switch off utility power at the distribution point where the UPS will be connected. Be absolutely

sure there is no power.

2 Remove the terminal block cover (four screws) and retain.

18

|

Installation and Startup

Installing the Input and Ground Wires

Terminal Position

132

3 Punch a hole in the terminal block cover for the input conduit using a Greenlee

®

punch or similar

device. The hole accommodates 3/4” or 1” IMC conduit.

4 Pull the input wire through the conduit, leaving approximately 2 ft (0.5m) of exposed wire. Attach

a flexible metal fitting to the end of the conduit.

5 Insert the conduit through the wiring access entry and attach the conduit fitting to the panel.

Strip 0.5” (1.5 cm) of insulation from the end of each incoming wire.

6 Connect the input and ground wires to the terminal block according to Table 1.

Table 1. UPS Wiring Specifications

Wire Function

Terminal

Position

UPS Wire Function

Terminal Wire

Size Rating*

Tightening Torque

Input

1 Input Ground

5.26–16 mm

2

(10–6 AWG)

2.49 Nm (22 lb in)

2 L2/Neutral In

3 L1 In

* Use a minimum:

S 10 AWG for equipment grounding wire, 75_C copper wire minimum

S 8 AWG for input line and neutral wires, 75_C copper wire minimum

7 Replace the terminal block cover.

ページを読み込んでいます...

Dell UPS 5600R クイックスタートガイド

関連論文

その他の書類