Sony Cyber-shot DSC-TX5 取扱説明書

カテゴリー
ビデオカメラ
タイプ
取扱説明書

このマニュアルも適しています

GB
CT
CS
MY
ID
TH
© 2010 Sony Corporation
4-170-840-63(1)
C:\FM\01COV.fm
master:Right
DSC-TX5
4-170-840-63(1)
DSC-TX5
GB Digital Still Camera/Instruction Manual
CT
CS
MY Kamera digital/Manual Arahan
ID Kamera Digital/Panduan Pengguna
TH
DSC-TX5
4-170-840-63(1)
AR
PR
4-170-840-63(1)
DSC-TX5
© 2010 Sony CorporationPrinted in Japan
AR
PR
GB
2
Owner’s Record
The model and serial numbers are located on the bottom. Record the serial number in the
space provided below. Refer to these numbers whenever you call upon your Sony dealer
regarding this product.
Model No. DSC-TX5
Serial No. ______________________________
To reduce fire or shock hazard, do not expose the unit to rain or
moisture.
If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the
proper configuration for the power outlet.
[ Battery pack
If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical
burns. Observe the following cautions.
Do not disassemble.
Do not crush and do not expose the battery pack to any shock or force such as
hammering, dropping or stepping on it.
Do not short circuit and do not allow metal objects to come into contact with the battery
terminals.
English
WARNING
CAUTION
GB
3
GB
Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a
car parked in the sun.
Do not incinerate or dispose of in fire.
Do not handle damaged or leaking lithium ion batteries.
Be sure to charge the battery pack using a genuine Sony battery charger or a device that
can charge the battery pack.
Keep the battery pack out of the reach of small children.
Keep the battery pack dry.
Replace only with the same or equivalent type recommended by Sony.
Dispose of used battery packs promptly as described in the instructions.
[ Battery charger
Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC
power source (mains) as long as it is connected to the wall outlet (wall socket). If some
trouble occurs while using the battery charger, immediately shut off the power by
disconnecting the plug from the wall outlet (wall socket).
[ RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are recyclable.
You can help preserve our environment by returning your used
rechargeable batteries to the collection and recycling location nearest
you.
For more information regarding recycling of rechargeable batteries,
call toll free
1-800-822-8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking Lithium-Ion batteries.
[ Battery pack
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
For Customers in the U.S.A. and Canada
GB
4
UL is an internationally recognized safety organization.
The UL Mark on the product means it has been UL Listed.
If you have any questions about this product, you may call:
Sony Customer Information Center
1-800-222-SONY (7669)
The number below is for the FCC related matters only.
[ Regulatory Information
[ CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual
could void your authority to operate this equipment.
For Customers in the U.S.A.
Declaration of Conformity
Trade Name: SONY
Model No.: DSC-TX5
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo,
San Diego, CA 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with Part15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
GB
5
GB
[ Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The supplied interface cable must be used with the equipment in order to comply with the
limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
[ Notice for the customers in the countries applying EU Directives
The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,
108-0075 Japan. The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or
guarantee matters please refer to the addresses given in separate service or guarantee
documents.
This product has been tested and found compliant with the limits set out in the EMC
Directive for using connection cables shorter than 3 meters (9.8 feet).
[ Attention
The electromagnetic fields at the specific frequencies may influence the picture and sound
of this unit.
[ Notice
If static electricity or electromagnetism causes data transfer to discontinue midway (fail),
restart the application or disconnect and connect the communication cable (USB, etc.)
again.
For Customers in Europe
GB
6
[ Disposal of Old Electrical & Electronic Equipment (Applicable in
the European Union and other European countries with separate
collection systems)
This symbol on the product or on its packaging indicates that this product
shall not be treated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling
of this product. The recycling of materials will help to conserve natural
resources. For more detailed information about recycling of this product,
please contact your local Civic Office, your household waste disposal service or the shop
where you purchased the product.
[ Disposal of waste batteries (applicable in the European Union
and other European countries with separate collection systems)
This symbol on the battery or on the packaging indicates that the battery
provided with this product shall not be treated as household waste.
On certain batteries this symbol might be used in combination with a
chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are
added if the battery contains more than 0.0005% mercury or 0.004% lead.
By ensuring these batteries are disposed of correctly, you will help prevent
potentially negative consequences for the environment and human health which could
otherwise be caused by inappropriate waste handling of the battery. The recycling of the
materials will help to conserve natural resources.
In case of products that for safety, performance or data integrity reasons require a
permanent connection with an incorporated battery, this battery should be replaced by
qualified service staff only. To ensure that the battery will be treated properly, hand over
the product at end-of-life to the applicable collection point for the recycling of electrical
and electronic equipment.
For all other batteries, please view the section on how to remove the battery from the
product safely.
Hand the battery over to the applicable collection point for the recycling of waste batteries.
For more detailed information about recycling of this product or battery, please contact
your local Civic Office, your household waste disposal service or the shop where you
purchased the product.
A moulded plug complying with BS 1363 is fitted to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the
supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or
mark) must be used.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the
fuse cover after you change the fuse. Never use the plug without the fuse cover. If you
should lose the fuse cover, please contact your nearest Sony service station.
Notice for customers in the United Kingdom
GB
7
GB
Table of contents
Getting started
About water-proof, dust-proof, and shock-proof performance
of the camera .............................................................................8
Refer to “Cyber-shot Handbook” (PDF) on supplied
CD-ROM...................................................................................11
Checking the accessories supplied.........................................11
Notes on using the camera ......................................................12
Identifying parts .......................................................................14
Charging the battery pack .......................................................15
Inserting the battery pack/a memory card
(sold separately) ...................................................................... 17
Setting the clock ......................................................................20
Shooting/viewing images
Shooting still images ................................................................21
Shooting movies.......................................................................22
Viewing images ........................................................................23
“Cyber-shot Handbook” (PDF)
Learning more about the camera (“Cyber-shot
Handbook”) .............................................................................. 24
Others
List of icons displayed on the screen ...................................... 25
Number of still images and recordable time of movies ...........27
Precautions ..............................................................................28
Specifications...........................................................................30
GB
8
About water-proof, dust-proof, and
shock-proof performance of the camera
This camera is equipped to be water-proof, dust-proof and shock-proof.
Damage caused from misuse, abuse or failure to properly maintain the camera
is not covered by the limited warranty.
This camera is water-proof/dust-proof equivalent to IEC60529 IP58. The
camera is operable up to a water depth of 3 m for 60 minutes.
Do not directly subject the camera to flowing water such as tap water.
Do not use in hot springs.
Use the camera in the recommended operating water temperature range of
–10°C to +40°C (14°F to 104°F).
Conforming to MIL-STD 810F Method 516.5-Shock standards, this product
has passed testing when dropped from a height of 1.5 m above a 5-cm thick
plywood board
*
.
* Depending on use conditions and circumstances, no guarantee is made regarding
damage to, malfunction of, or the water-proof performance of this camera.
As for dust-proof/shock-proof performance, there is no guarantee that the
camera will not become scratched or dented.
Sometimes water-proof performance is lost if the camera is subjected to a
strong shock such as from being dropped. We recommend the camera be
inspected at an authorized repair shop for a fee.
Accessories supplied do not meet water-proof, dust-proof, and shock-proof
specifications.
Notes before using the camera under/near water
Make sure that no foreign matter such as sand, hair, or dirt gets inside the
battery/memory card cover or multi-connector cover. Even a small amount
of foreign matter may lead to water entering the camera.
Confirm that the sealing gasket and its
mating surfaces have not become scratched.
Even a small scratch may lead to water
entering the camera. If the sealing gasket or
its mating surfaces become scratched, take
the camera to an authorized repair shop to
have the sealing gasket replaced for a fee.
If dirt or sand gets on the sealing gasket or
its mating surfaces, wipe the area clean with
a soft cloth that will not leave behind any
fibers. Do not use a sharp-pointed
implement to prevent the sealing gasket and
its mating surfaces from becoming scratched.
1 Sealing gasket
2 Surface contacting the
sealing gasket
GB
9
GB
Do not open/close the battery/memory card cover or multi-connector cover
with wet or sandy hands or near water. There is a risk this will lead to sand or
water getting inside. Before opening the cover, perform the procedure
described in “Cleaning after using the camera under/near water”.
Open the cover with the camera completely dry.
Always confirm that the battery/memory card cover and multi-connector
cover have been securely locked.
Notes on using the camera under/near water
Do not subject the camera to shock such as from jumping into water.
Do not open and close the battery/memory card cover or multi-connector
cover while under/near water.
Use a separately available housing (Marine Pack) if going more than
3 meters under water.
This camera sinks in water. Place your hand through the wrist strap to
prevent the camera from sinking.
Faint, white, circular spots may appear in under-water flash photos due to
reflections off of floating objects. This is not a malfunction.
Select (Underwater) in Scene Selection to shoot underwater with less
distortion.
If water drops or other foreign matter is present on the lens, you will be
unable to record clear images.
Cleaning after using the camera under/near
water
Always clean the camera with water after use
within 60 minutes, and do not open the battery/
memory card cover before cleaning is finished.
Sand or water may get inside places where it
cannot be seen. If not rinsed, water-proof
performance will be degraded.
Allow the camera to sit in pure water poured into a cleaning bowl for more
than 5 minutes. Then, gently shake the camera, press each button, slide the
zoom (W/T) lever or the lens cover inside the water, to clean away any salt,
sand or other matter lodged around the buttons or the lens cover.
After rinsing, wipe away water drops with a soft cloth. Allow the camera to
dry completely in a shady location with good ventilation. Do not blow dry
with a hair dryer as there is a risk of deformation and/or degraded water-
proof performance.
This camera is constructed to drain water. Water will drain from openings
around the ON/OFF (Power) button, zoom (W/T) lever, and other controls.
After removing from water, place the camera on a dry cloth for a while to
allow water to drain.
Bubbles may appear when the camera is placed under water. This is not a
malfunction.
GB
10
The camera body may become discolored if it comes in contact with
sunscreen or suntan oil. If the camera does come in contact with sunscreen or
suntan oil, quickly wipe it clean.
Do not allow the camera to sit with salt water inside or on the surface. This
may lead to corrosion or discoloration, and degradation of water-proof
performance.
To maintain the water-proof performance, we recommend that once a year
you take the camera to your dealer, or to an authorized repair shop, to have
the sealing gasket of the battery/memory card cover, or of the multi-
connector cover replaced for a fee.
GB
11
GB
Checking the accessories supplied
Battery charger BC-CSN/BC-CSNB (1)
Power cord (mains lead) (not supplied in the USA and Canada) (1)
Rechargeable battery pack NP-BN1 (1)
Paint pen (1)
USB, A/V cable for multi-use terminal (1)
Wrist strap (1)
•CD-ROM (1)
Cyber-shot application software
“Cyber-shot Handbook”
Instruction Manual (this manual) (1)
Notes on the water-proofing (1)
Accessories supplied do not meet water-proof, dust-proof, and shock-proof
specifications.
The wrist strap is already attached to the camera at the factory. Place your
hand through the loop to prevent the camera from sinking or sustaining
damage from being dropped.
Refer to “Cyber-shot Handbook” (PDF)
on supplied CD-ROM
For details on advanced operations, please read “Cyber-
shot Handbook” (PDF) on the CD-ROM (supplied) using
a computer.
Refer to “Cyber-shot Handbook” for in-depth instructions
on shooting or viewing images and connecting the camera
to your computer, printer or TV (page 24).
Notes
GB
12
Notes on using the camera
Changing the language setting
The screen language can be changed if necessary.
To change the language setting, touch , then select (Settings) t
(Main Settings) t [Language Setting].
Internal memory and memory card back up
Do not turn off the camera, remove the battery pack, or remove the memory
card while the access lamp is lit. Otherwise, the internal memory data or the
memory card may be damaged. Be sure to make a backup copy to protect your
data.
On database files
When you insert a memory card without a database file into the camera and
turn on the power, part of the memory card capacity is used to automatically
create a database file. It may take some time until you can perform the next
operation.
Notes on recording/playback
To ensure stable operations of the memory card, we recommend that you use
this camera to format any memory card being used with this camera for the
first time. Note that formatting will erase all data recorded on the memory
card. This data cannot be restored. Be sure to back-up any important data to a
PC or other storage location.
Before you start recording, make a trial recording to make sure that the
camera is working correctly.
Do not aim the camera at the sun or other bright light. It may cause the
malfunction of the camera.
Do not use the camera near a location that generates strong radio waves or
emits radiation. Otherwise, the camera may not properly record or play back
images.
If moisture condensation occurs, remove it before using the camera.
Do not shake or strike the camera. It may cause a malfunction and you may
not be able to record images. Furthermore, the recording media may become
unusable or image data may be damaged.
Clean the flash surface before use. The heat of flash emission may cause dirt
on the flash surface to become discolored or to stick to the flash surface,
resulting in insufficient light emission.
GB
13
GB
Notes on the LCD screen
The LCD screen is manufactured using extremely high-precision technology
so over 99.99% of the pixels are operational for effective use. However,
some tiny black and/or bright dots (white, red, blue or green) may appear on
the LCD screen. These dots are a normal result of the manufacturing process,
and do not affect the recording.
Do not press against the LCD screen. The screen may be discolored and that
may cause a malfunction.
Please use Sony genuine accessories
If you use accessories manufactured by companies other than Sony, this could
cause a camera trouble.
Using other manufacturers’ camera cases with magnets could cause a power
supply trouble.
On camera’s temperature
Your camera and battery may get warm due to continuous use, but it is not a
malfunction.
On the overheat protection
Depending on the camera and battery temperature, you may be unable to
record movies or the power may turn off automatically to protect the camera.
A message will be displayed on the LCD screen before the power turns off or
you can no longer record movies.
On image data compatibility
The camera conforms with DCF (Design rule for Camera File system)
universal standard established by JEITA (Japan Electronics and Information
Technology Industries Association).
Sony does not guarantee that the camera will play back images recorded or
edited with other equipment, or that other equipment will play back images
recorded with the camera.
Warning on copyright
Television programs, films, videotapes, and other materials may be
copyrighted. Unauthorized recording of such materials may be contrary to the
provisions of the copyright laws.
No compensation for damaged content or recording failure
Sony cannot compensate for failure to record or loss or damage of recorded
content due to a malfunction of the camera or recording media, etc.
GB
14
Identifying parts
A Shutter button
B Microphone
C Lens cover
D ON/OFF (Power) button
E Flash
F Self-timer lamp/Smile Shutter
lamp/AF illuminator
G Lens
H LCD screen/Touch panel
I Speaker
J (Playback) button
K Zoom (W/T) lever
L Hook for wrist strap
M Memory card slot
N Battery eject lever
O Multi-connector
P Tripod receptacle
Use a tripod with a screw less
than 5.5 mm (7/32 inches) long.
Otherwise, you cannot firmly
secure the camera, and damage to
the camera may occur.
Q Battery/Memory card cover
R Battery insertion slot
S Access lamp
T Multi-connector cover
GB
15
GB
Charging the battery pack
x
Charging time
1
Insert the battery pack into the
battery charger.
You can charge the battery even when it is
partially charged.
2
Connect the battery
charger to the wall
outlet (wall socket).
If you continue charging
the battery pack for about
one more hour after the
CHARGE lamp turns off,
the charge will last slightly
longer (full charge).
CHARGE lamp
Lit: Charging
Off: Charging finished
(normal charge)
3
When charging is finished, disconnect the battery
charger.
Full charge time Normal charge time
Approx. 245 min. Approx. 185 min.
Battery
pack
For customers in the USA and
Canada
CHARGE lamp
Power cord
(mains lead)
CHARGE lamp
Plug
For customers in countries/regions
other than the USA and Canada
GB
16
The table above shows the time required to charge a fully depleted battery pack at
a temperature of 25°C (77°F). Charging may take longer depending on conditions
of use and circumstances.
Connect the battery charger to the nearest wall outlet (wall socket).
When charging is finished, disconnect the power cord (mains lead) from the wall
outlet (wall socket), and remove the battery pack from the battery charger.
Be sure to use the battery pack or the battery charger of the genuine Sony brand.
x
Battery life and number of still images you can
record/view
The number of still images that can be recorded is based on the CIPA standard,
and is for shooting under the following conditions.
(CIPA: Camera & Imaging Products Association)
– [LCD Brightness] is set to [Normal].
– Shooting once every 30 seconds.
– The zoom is switched alternately between the W and T ends.
– The flash strobes once every two times.
– The power turns on and off once every ten times.
– A fully charged battery pack (supplied) is used at an ambient temperature of
25°C (77°F).
– Using Sony “Memory Stick PRO Duo” media (sold separately).
Notes
Battery life (min.) No. of Images
Recording Approx. 125 Approx. 250
Viewing Approx. 250 Approx. 5000
Note
z Using the camera abroad
You can use the camera and the battery charger (supplied) in any country
or region where the power supply is within 100 V to 240 V AC, 50/60 Hz.
Do not use an electronic transformer (travel converter). This may cause a
malfunction.
GB
17
GB
Inserting the battery pack/a memory card
(sold separately)
1
Open the cover.
2
Insert a memory card
(sold separately).
With the notched corner facing as
illustrated, insert the memory card
until it clicks into place.
3
Insert the battery pack.
Align the battery pack with the
guide inside the battery insertion
slot. Then, pressing the battery eject
lever with the edge of the battery
pack in the direction of the arrow,
insert the battery pack until the
battery eject lever locks into place.
4
Close the cover.
Securely close the battery cover
until you hear the slide lock on the
cover catch in place and so that the
yellow mark under the slide lock can
no longer be seen.
If foreign matter such as sand gets
inside the cover, the sealing gasket may be scratched and it may cause a
malfunction (page 8).
Note the notched corner facing
the correct direction.
Battery eject lever
GB
18
x
Memory card that you can use
The following memory cards are compatible with this camera: “Memory Stick
PRO Duo” media, “Memory Stick PRO-HG Duo” media, “Memory Stick
Duo” media, SD memory card, SDHC memory card and SDXC memory card.
However, all memory cards are not guaranteed to work with this camera.
MultiMediaCard is not compatible.
Images recorded on an SDXC memory card cannot be transferred or played
back on computers or AV devices that are not exFAT-compatible, even when
the camera is connected to the computer or AV device using a USB cable.
Before connecting, make sure that the device is exFAT-compatible. If
connected to a device that is not exFAT-compatible, a format drive request
may appear. Do not format the drive, or all data will be lost. (exFAT is the file
system used by SDXC memory cards.)
In this manual, the term “Memory Stick Duo” media is used to refer to “Memory
Stick PRO Duo” media, “Memory Stick PRO-HG Duo” media and “Memory
Stick Duo” media, and the term “SD card” is used to refer to SD memory card,
SDHC memory card and SDXC memory card.
When recording movies, it is recommended that you use the following memory
cards:
(Mark2) (“Memory Stick PRO Duo” (Mark2) media)
(“Memory Stick PRO-HG Duo” media)
– SD memory card, SDHC memory card or SDXC memory card (Class 4 or faster)
This camera should be operated at between –10°C and +40°C, but according to the
type of memory card, the operating temperature may vary. For details, see the
operating instructions supplied with the memory card.
For details on the number of images/time that can be recorded, see page 27.
x
To remove the memory card
Never remove the memory card/the battery pack when the access lamp is lit. This
may cause damage to data or the memory card.
Note
Make sure that the access lamp is not lit,
then push the memory card in once.
Note
Access lamp
GB
19
GB
x
When there is no memory card inserted
Images are stored in the camera’s internal memory (approximately 45 MB).
To copy images from the internal memory to a memory card, insert a memory
card in the camera, then touch t (Settings) t (Memory Card
Tool) t [Copy].
x
To remove the battery pack
x
Notes on the multi-connector cover
To open the multi-connector cover, first open the battery/memory card cover.
Then, pull the notch on the left side of the multi-connector cover out with the
fingernail. Close the multi-connector cover firmly, then the battery/memory
card cover.
x
Checking the remaining battery charge
A remaining charge indicator appears on the LCD screen.
It takes about one minute until the correct remaining charge indicator appears.
The remaining charge indicator may not be correct under certain circumstances.
When [Power Save] is set to [Standard] or [Stamina], if you do not operate the
camera for a certain period of time while the power is on, the LCD screen becomes
dark, then the camera turns off automatically (Auto power-off function).
To keep clean battery pack terminal and prevent short-circuiting, place the battery
pack in a plastic bag, etc. when carrying and storing to isolate it from other metal
objects, etc.
Slide the battery eject lever. Be sure not
to drop the battery pack.
Notes
Battery eject lever
Multi-connector cover
High Low
GB
20
Setting the clock
x
Setting the date and time again
Touch t (Settings) t (Clock Settings).
1
Lower the lens cover.
The camera is turned on.
You can also turn on the camera
by pressing the ON/OFF (Power)
button.
It may take time for the power to
turn on and allow operation.
2
Select the desired date display format, then touch
[OK].
3
Select Daylight Savings [On]/[Off], then touch [OK].
4
Select the item to be set, then set the value with v/V
and touch [OK].
Midnight is indicated as 12:00 AM, and noon as 12:00 PM.
5
Select your desired area with b/B, then touch [OK]
t [OK].
ON/OFF (Power) button
Lens cover
1 / 1

Sony Cyber-shot DSC-TX5 取扱説明書

カテゴリー
ビデオカメラ
タイプ
取扱説明書
このマニュアルも適しています