Sony Cyber-shot DSC-TX5 取扱説明書

GB

CT

CS

MY

ID

TH

4-170-840-63(1)

C:\FM\01COV.fm

master:Right

DSC-TX5

4-170-840-63(1)

DSC-TX5

GB Digital Still Camera/Instruction Manual

CT

CS

MY Kamera digital/Manual Arahan

ID Kamera Digital/Panduan Pengguna

TH

DSC-TX5

4-170-840-63(1)

AR

PR

4-170-840-63(1)

DSC-TX5

AR

PR

GB

2

Owner’s Record

The model and serial numbers are located on the bottom. Record the serial number in the

space provided below. Refer to these numbers whenever you call upon your Sony dealer

regarding this product.

Model No. DSC-TX5

Serial No. ______________________________

To reduce fire or shock hazard, do not expose the unit to rain or

moisture.

If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the

proper configuration for the power outlet.

[ Battery pack

If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical

burns. Observe the following cautions.

• Do not disassemble.

• Do not crush and do not expose the battery pack to any shock or force such as

hammering, dropping or stepping on it.

• Do not short circuit and do not allow metal objects to come into contact with the battery

terminals.

English

WARNING

CAUTION

GB

3

GB

• Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a

car parked in the sun.

• Do not incinerate or dispose of in fire.

• Do not handle damaged or leaking lithium ion batteries.

• Be sure to charge the battery pack using a genuine Sony battery charger or a device that

can charge the battery pack.

• Keep the battery pack out of the reach of small children.

• Keep the battery pack dry.

• Replace only with the same or equivalent type recommended by Sony.

• Dispose of used battery packs promptly as described in the instructions.

[ Battery charger

Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC

power source (mains) as long as it is connected to the wall outlet (wall socket). If some

trouble occurs while using the battery charger, immediately shut off the power by

disconnecting the plug from the wall outlet (wall socket).

[ RECYCLING LITHIUM-ION BATTERIES

Lithium-Ion batteries are recyclable.

You can help preserve our environment by returning your used

rechargeable batteries to the collection and recycling location nearest

you.

For more information regarding recycling of rechargeable batteries,

call toll free

1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Lithium-Ion batteries.

[ Battery pack

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

For Customers in the U.S.A. and Canada

GB

4

UL is an internationally recognized safety organization.

The UL Mark on the product means it has been UL Listed.

If you have any questions about this product, you may call:

Sony Customer Information Center

1-800-222-SONY (7669)

The number below is for the FCC related matters only.

[ Regulatory Information

[ CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual

could void your authority to operate this equipment.

For Customers in the U.S.A.

Declaration of Conformity

Trade Name: SONY

Model No.: DSC-TX5

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

GB

5

GB

[ Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The supplied interface cable must be used with the equipment in order to comply with the

limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

[ Notice for the customers in the countries applying EU Directives

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or

guarantee matters please refer to the addresses given in separate service or guarantee

documents.

This product has been tested and found compliant with the limits set out in the EMC

Directive for using connection cables shorter than 3 meters (9.8 feet).

[ Attention

The electromagnetic fields at the specific frequencies may influence the picture and sound

of this unit.

[ Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail),

restart the application or disconnect and connect the communication cable (USB, etc.)

again.

For Customers in Europe

GB

6

[ Disposal of Old Electrical & Electronic Equipment (Applicable in

the European Union and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that this product

shall not be treated as household waste. Instead it shall be handed over to

the applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling

of this product. The recycling of materials will help to conserve natural

resources. For more detailed information about recycling of this product,

please contact your local Civic Office, your household waste disposal service or the shop

where you purchased the product.

[ Disposal of waste batteries (applicable in the European Union

and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery

provided with this product shall not be treated as household waste.

On certain batteries this symbol might be used in combination with a

chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are

added if the battery contains more than 0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will help prevent

potentially negative consequences for the environment and human health which could

otherwise be caused by inappropriate waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity reasons require a

permanent connection with an incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will be treated properly, hand over

the product at end-of-life to the applicable collection point for the recycling of electrical

and electronic equipment.

For all other batteries, please view the section on how to remove the battery from the

product safely.

Hand the battery over to the applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or battery, please contact

your local Civic Office, your household waste disposal service or the shop where you

purchased the product.

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the

supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or

mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the

fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service station.

Notice for customers in the United Kingdom

GB

7

GB

Table of contents

Getting started

About water-proof, dust-proof, and shock-proof performance

of the camera .............................................................................8

Refer to “Cyber-shot Handbook” (PDF) on supplied

CD-ROM...................................................................................11

Checking the accessories supplied.........................................11

Notes on using the camera ......................................................12

Identifying parts .......................................................................14

Charging the battery pack .......................................................15

Inserting the battery pack/a memory card

(sold separately) ...................................................................... 17

Setting the clock ......................................................................20

Shooting/viewing images

Shooting still images ................................................................21

Shooting movies.......................................................................22

Viewing images ........................................................................23

“Cyber-shot Handbook” (PDF)

Learning more about the camera (“Cyber-shot

Handbook”) .............................................................................. 24

Others

List of icons displayed on the screen ...................................... 25

Number of still images and recordable time of movies ...........27

Precautions ..............................................................................28

Specifications...........................................................................30

GB

8

About water-proof, dust-proof, and

shock-proof performance of the camera

This camera is equipped to be water-proof, dust-proof and shock-proof.

Damage caused from misuse, abuse or failure to properly maintain the camera

is not covered by the limited warranty.

• This camera is water-proof/dust-proof equivalent to IEC60529 IP58. The

camera is operable up to a water depth of 3 m for 60 minutes.

• Do not directly subject the camera to flowing water such as tap water.

• Do not use in hot springs.

• Use the camera in the recommended operating water temperature range of

–10°C to +40°C (14°F to 104°F).

• Conforming to MIL-STD 810F Method 516.5-Shock standards, this product

has passed testing when dropped from a height of 1.5 m above a 5-cm thick

plywood board

*

.

* Depending on use conditions and circumstances, no guarantee is made regarding

damage to, malfunction of, or the water-proof performance of this camera.

• As for dust-proof/shock-proof performance, there is no guarantee that the

camera will not become scratched or dented.

• Sometimes water-proof performance is lost if the camera is subjected to a

strong shock such as from being dropped. We recommend the camera be

inspected at an authorized repair shop for a fee.

• Accessories supplied do not meet water-proof, dust-proof, and shock-proof

specifications.

Notes before using the camera under/near water

• Make sure that no foreign matter such as sand, hair, or dirt gets inside the

battery/memory card cover or multi-connector cover. Even a small amount

of foreign matter may lead to water entering the camera.

• Confirm that the sealing gasket and its

mating surfaces have not become scratched.

Even a small scratch may lead to water

entering the camera. If the sealing gasket or

its mating surfaces become scratched, take

the camera to an authorized repair shop to

have the sealing gasket replaced for a fee.

• If dirt or sand gets on the sealing gasket or

its mating surfaces, wipe the area clean with

a soft cloth that will not leave behind any

fibers. Do not use a sharp-pointed

implement to prevent the sealing gasket and

its mating surfaces from becoming scratched.

1 Sealing gasket

2 Surface contacting the

sealing gasket

GB

9

GB

• Do not open/close the battery/memory card cover or multi-connector cover

with wet or sandy hands or near water. There is a risk this will lead to sand or

water getting inside. Before opening the cover, perform the procedure

described in “Cleaning after using the camera under/near water”.

• Open the cover with the camera completely dry.

• Always confirm that the battery/memory card cover and multi-connector

cover have been securely locked.

Notes on using the camera under/near water

• Do not subject the camera to shock such as from jumping into water.

• Do not open and close the battery/memory card cover or multi-connector

cover while under/near water.

• Use a separately available housing (Marine Pack) if going more than

3 meters under water.

• This camera sinks in water. Place your hand through the wrist strap to

prevent the camera from sinking.

• Faint, white, circular spots may appear in under-water flash photos due to

reflections off of floating objects. This is not a malfunction.

• Select (Underwater) in Scene Selection to shoot underwater with less

distortion.

• If water drops or other foreign matter is present on the lens, you will be

unable to record clear images.

Cleaning after using the camera under/near

water

• Always clean the camera with water after use

within 60 minutes, and do not open the battery/

memory card cover before cleaning is finished.

Sand or water may get inside places where it

cannot be seen. If not rinsed, water-proof

performance will be degraded.

• Allow the camera to sit in pure water poured into a cleaning bowl for more

than 5 minutes. Then, gently shake the camera, press each button, slide the

zoom (W/T) lever or the lens cover inside the water, to clean away any salt,

sand or other matter lodged around the buttons or the lens cover.

• After rinsing, wipe away water drops with a soft cloth. Allow the camera to

dry completely in a shady location with good ventilation. Do not blow dry

with a hair dryer as there is a risk of deformation and/or degraded water-

proof performance.

• This camera is constructed to drain water. Water will drain from openings

around the ON/OFF (Power) button, zoom (W/T) lever, and other controls.

After removing from water, place the camera on a dry cloth for a while to

allow water to drain.

• Bubbles may appear when the camera is placed under water. This is not a

malfunction.

GB

10

• The camera body may become discolored if it comes in contact with

sunscreen or suntan oil. If the camera does come in contact with sunscreen or

suntan oil, quickly wipe it clean.

• Do not allow the camera to sit with salt water inside or on the surface. This

may lead to corrosion or discoloration, and degradation of water-proof

performance.

• To maintain the water-proof performance, we recommend that once a year

you take the camera to your dealer, or to an authorized repair shop, to have

the sealing gasket of the battery/memory card cover, or of the multi-

connector cover replaced for a fee.

GB

11

GB

Checking the accessories supplied

• Battery charger BC-CSN/BC-CSNB (1)

• Power cord (mains lead) (not supplied in the USA and Canada) (1)

• Rechargeable battery pack NP-BN1 (1)

• Paint pen (1)

• USB, A/V cable for multi-use terminal (1)

• Wrist strap (1)

•CD-ROM (1)

– Cyber-shot application software

– “Cyber-shot Handbook”

• Instruction Manual (this manual) (1)

• Notes on the water-proofing (1)

• Accessories supplied do not meet water-proof, dust-proof, and shock-proof

specifications.

•

The wrist strap is already attached to the camera at the factory. Place your

hand through the loop to prevent the camera from sinking or sustaining

damage from being dropped.

Refer to “Cyber-shot Handbook” (PDF)

on supplied CD-ROM

For details on advanced operations, please read “Cyber-

shot Handbook” (PDF) on the CD-ROM (supplied) using

a computer.

Refer to “Cyber-shot Handbook” for in-depth instructions

on shooting or viewing images and connecting the camera

to your computer, printer or TV (page 24).

Notes

GB

12

Notes on using the camera

Changing the language setting

The screen language can be changed if necessary.

To change the language setting, touch , then select (Settings) t

(Main Settings) t [Language Setting].

Internal memory and memory card back up

Do not turn off the camera, remove the battery pack, or remove the memory

card while the access lamp is lit. Otherwise, the internal memory data or the

memory card may be damaged. Be sure to make a backup copy to protect your

data.

On database files

When you insert a memory card without a database file into the camera and

turn on the power, part of the memory card capacity is used to automatically

create a database file. It may take some time until you can perform the next

operation.

Notes on recording/playback

• To ensure stable operations of the memory card, we recommend that you use

this camera to format any memory card being used with this camera for the

first time. Note that formatting will erase all data recorded on the memory

card. This data cannot be restored. Be sure to back-up any important data to a

PC or other storage location.

• Before you start recording, make a trial recording to make sure that the

camera is working correctly.

• Do not aim the camera at the sun or other bright light. It may cause the

malfunction of the camera.

• Do not use the camera near a location that generates strong radio waves or

emits radiation. Otherwise, the camera may not properly record or play back

images.

• If moisture condensation occurs, remove it before using the camera.

• Do not shake or strike the camera. It may cause a malfunction and you may

not be able to record images. Furthermore, the recording media may become

unusable or image data may be damaged.

• Clean the flash surface before use. The heat of flash emission may cause dirt

on the flash surface to become discolored or to stick to the flash surface,

resulting in insufficient light emission.

GB

13

GB

Notes on the LCD screen

• The LCD screen is manufactured using extremely high-precision technology

so over 99.99% of the pixels are operational for effective use. However,

some tiny black and/or bright dots (white, red, blue or green) may appear on

the LCD screen. These dots are a normal result of the manufacturing process,

and do not affect the recording.

• Do not press against the LCD screen. The screen may be discolored and that

may cause a malfunction.

Please use Sony genuine accessories

If you use accessories manufactured by companies other than Sony, this could

cause a camera trouble.

• Using other manufacturers’ camera cases with magnets could cause a power

supply trouble.

On camera’s temperature

Your camera and battery may get warm due to continuous use, but it is not a

malfunction.

On the overheat protection

Depending on the camera and battery temperature, you may be unable to

record movies or the power may turn off automatically to protect the camera.

A message will be displayed on the LCD screen before the power turns off or

you can no longer record movies.

On image data compatibility

• The camera conforms with DCF (Design rule for Camera File system)

universal standard established by JEITA (Japan Electronics and Information

Technology Industries Association).

• Sony does not guarantee that the camera will play back images recorded or

edited with other equipment, or that other equipment will play back images

recorded with the camera.

Warning on copyright

Television programs, films, videotapes, and other materials may be

copyrighted. Unauthorized recording of such materials may be contrary to the

provisions of the copyright laws.

No compensation for damaged content or recording failure

Sony cannot compensate for failure to record or loss or damage of recorded

content due to a malfunction of the camera or recording media, etc.

GB

14

Identifying parts

A Shutter button

B Microphone

C Lens cover

D ON/OFF (Power) button

E Flash

F Self-timer lamp/Smile Shutter

lamp/AF illuminator

G Lens

H LCD screen/Touch panel

I Speaker

J (Playback) button

K Zoom (W/T) lever

L Hook for wrist strap

M Memory card slot

N Battery eject lever

O Multi-connector

P Tripod receptacle

• Use a tripod with a screw less

than 5.5 mm (7/32 inches) long.

Otherwise, you cannot firmly

secure the camera, and damage to

the camera may occur.

Q Battery/Memory card cover

R Battery insertion slot

S Access lamp

T Multi-connector cover

GB

15

GB

Charging the battery pack

x

Charging time

1

Insert the battery pack into the

battery charger.

• You can charge the battery even when it is

partially charged.

2

Connect the battery

charger to the wall

outlet (wall socket).

If you continue charging

the battery pack for about

one more hour after the

CHARGE lamp turns off,

the charge will last slightly

longer (full charge).

CHARGE lamp

Lit: Charging

Off: Charging finished

(normal charge)

3

When charging is finished, disconnect the battery

charger.

Full charge time Normal charge time

Approx. 245 min. Approx. 185 min.

Battery

pack

For customers in the USA and

Canada

CHARGE lamp

Power cord

(mains lead)

CHARGE lamp

Plug

For customers in countries/regions

other than the USA and Canada

GB

16

• The table above shows the time required to charge a fully depleted battery pack at

a temperature of 25°C (77°F). Charging may take longer depending on conditions

of use and circumstances.

• Connect the battery charger to the nearest wall outlet (wall socket).

• When charging is finished, disconnect the power cord (mains lead) from the wall

outlet (wall socket), and remove the battery pack from the battery charger.

• Be sure to use the battery pack or the battery charger of the genuine Sony brand.

x

Battery life and number of still images you can

record/view

• The number of still images that can be recorded is based on the CIPA standard,

and is for shooting under the following conditions.

(CIPA: Camera & Imaging Products Association)

– [LCD Brightness] is set to [Normal].

– Shooting once every 30 seconds.

– The zoom is switched alternately between the W and T ends.

– The flash strobes once every two times.

– The power turns on and off once every ten times.

– A fully charged battery pack (supplied) is used at an ambient temperature of

25°C (77°F).

– Using Sony “Memory Stick PRO Duo” media (sold separately).

Notes

Battery life (min.) No. of Images

Recording Approx. 125 Approx. 250

Viewing Approx. 250 Approx. 5000

Note

z Using the camera abroad

You can use the camera and the battery charger (supplied) in any country

or region where the power supply is within 100 V to 240 V AC, 50/60 Hz.

Do not use an electronic transformer (travel converter). This may cause a

malfunction.

GB

17

GB

Inserting the battery pack/a memory card

(sold separately)

1

Open the cover.

2

Insert a memory card

(sold separately).

With the notched corner facing as

illustrated, insert the memory card

until it clicks into place.

3

Insert the battery pack.

Align the battery pack with the

guide inside the battery insertion

slot. Then, pressing the battery eject

lever with the edge of the battery

pack in the direction of the arrow,

insert the battery pack until the

battery eject lever locks into place.

4

Close the cover.

Securely close the battery cover

until you hear the slide lock on the

cover catch in place and so that the

yellow mark under the slide lock can

no longer be seen.

• If foreign matter such as sand gets

inside the cover, the sealing gasket may be scratched and it may cause a

malfunction (page 8).

Note the notched corner facing

the correct direction.

Battery eject lever

GB

18

x

Memory card that you can use

The following memory cards are compatible with this camera: “Memory Stick

PRO Duo” media, “Memory Stick PRO-HG Duo” media, “Memory Stick

Duo” media, SD memory card, SDHC memory card and SDXC memory card.

However, all memory cards are not guaranteed to work with this camera.

MultiMediaCard is not compatible.

Images recorded on an SDXC memory card cannot be transferred or played

back on computers or AV devices that are not exFAT-compatible, even when

the camera is connected to the computer or AV device using a USB cable.

Before connecting, make sure that the device is exFAT-compatible. If

connected to a device that is not exFAT-compatible, a format drive request

may appear. Do not format the drive, or all data will be lost. (exFAT is the file

system used by SDXC memory cards.)

• In this manual, the term “Memory Stick Duo” media is used to refer to “Memory

Stick PRO Duo” media, “Memory Stick PRO-HG Duo” media and “Memory

Stick Duo” media, and the term “SD card” is used to refer to SD memory card,

SDHC memory card and SDXC memory card.

• When recording movies, it is recommended that you use the following memory

cards:

– (Mark2) (“Memory Stick PRO Duo” (Mark2) media)

– (“Memory Stick PRO-HG Duo” media)

– SD memory card, SDHC memory card or SDXC memory card (Class 4 or faster)

• This camera should be operated at between –10°C and +40°C, but according to the

type of memory card, the operating temperature may vary. For details, see the

operating instructions supplied with the memory card.

For details on the number of images/time that can be recorded, see page 27.

x

To remove the memory card

• Never remove the memory card/the battery pack when the access lamp is lit. This

may cause damage to data or the memory card.

Note

Make sure that the access lamp is not lit,

then push the memory card in once.

Note

Access lamp

GB

19

GB

x

When there is no memory card inserted

Images are stored in the camera’s internal memory (approximately 45 MB).

To copy images from the internal memory to a memory card, insert a memory

card in the camera, then touch t (Settings) t (Memory Card

Tool) t [Copy].

x

To remove the battery pack

x

Notes on the multi-connector cover

To open the multi-connector cover, first open the battery/memory card cover.

Then, pull the notch on the left side of the multi-connector cover out with the

fingernail. Close the multi-connector cover firmly, then the battery/memory

card cover.

x

Checking the remaining battery charge

A remaining charge indicator appears on the LCD screen.

• It takes about one minute until the correct remaining charge indicator appears.

• The remaining charge indicator may not be correct under certain circumstances.

• When [Power Save] is set to [Standard] or [Stamina], if you do not operate the

camera for a certain period of time while the power is on, the LCD screen becomes

dark, then the camera turns off automatically (Auto power-off function).

• To keep clean battery pack terminal and prevent short-circuiting, place the battery

pack in a plastic bag, etc. when carrying and storing to isolate it from other metal

objects, etc.

Slide the battery eject lever. Be sure not

to drop the battery pack.

Notes

Battery eject lever

Multi-connector cover

High Low

GB

20

Setting the clock

x

Setting the date and time again

Touch t (Settings) t (Clock Settings).

1

Lower the lens cover.

The camera is turned on.

• You can also turn on the camera

by pressing the ON/OFF (Power)

button.

• It may take time for the power to

turn on and allow operation.

2

Select the desired date display format, then touch

[OK].

3

Select Daylight Savings [On]/[Off], then touch [OK].

4

Select the item to be set, then set the value with v/V

and touch [OK].

• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.

5

Select your desired area with b/B, then touch [OK]

t [OK].

ON/OFF (Power) button

Lens cover

ページが読み込まれています...

Sony Cyber-shot DSC-TX5 取扱説明書

このマニュアルも適しています

Sony Cyber-shot DSC-TX5 取扱説明書

関連論文

その他のドキュメント