X11SPA-TF
X11SPA-T
ENGLISH
繁體中文
简体中文
日本語
(
한국어
QUICK REFERENCE GUIDE
Revision 1.0b
X11SPA-TF/X11SPA-T QUICK REFERENCE GUIDE
Standardized Warning Statements
Motherboards
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations where bodily injury
might occur. Should you have questions or experience difculty, contact Supermicro's Technical Support Department
for assistance. Only certied technicians should attempt to install or congure components.
Read this section in its entirety before installing or conguring components in the Supermicro chassis.
WARNING: This product can expose you to chemicals including
lead, known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.
!
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-
lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理
廢棄舊電池。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理
废旧电池。
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメーカーが推奨する型、または同等のもの
を使用下さい。 使用済電池は製造元の指示に従って処分して下さい。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한
종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.
Product Safety Information
X11SPA-TF/X11SPA-T QUICK REFERENCE GUIDE
限用物質含有情況標示聲明書
限用物質含有情況標示聲明書
設備名稱：主機板
/
Motherboard
, 型號（型式）:
X11SPA-TF, X11SPA-T
單元Ｕnit
限用物質及其化學符號
鉛Lead
(Pb)
汞Mercury
(Hg)
鎘Cadmium
(Cd)
六價鉻
Hexavalent
chromium
(Cr
+6
)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
主機板
(Motherboard)
－ ○ ○ ○ ○ ○
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準
值。
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考3.〝－〞係指該項限用物質為排除項目。
Equipment name
Type designation (Type)
Restricted substances and its chemical symbols
Declaration of the Presence Condition of the Restricted Substances Marking
Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the
reference percentage value of presence condition.
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3：The “−” indicates that the restricted substance corresponds to the exemption.
X11SPA-TF/X11SPA-T QUICK REFERENCE GUIDE BIOS POST Codes
AMI BIOS POST Codes
About AMI BIOS POST Codes
The table below lists some of AMI BIOS POST codes for X11SPA-TF/X11SPA-T. For more information, refer to https://
www.supermicro.com/manuals/other/AMI_AptioV_BIOS_POST_Codes_for_SM_Motherboards.pdf.
Code Description
0x32 CPU post-memory initialization is started
0x55 No Memory detected or memory failed
0x63 CPU DXE initialization is started
0x69 North Bridge DXE initialization is started
0x70 South Bridge DXE initialization is started
0x92 PCI Bus initialization is started
0x99 Super IO Initialization
0x9A USB initialization is started
0xA0 IDE initialization is started
0xA9 Boot into BIOS setup menu
0xAE Legacy Boot event
0xB2 Legacy Option ROM Initialization
0xB4 USB hot plug
0xD6 No console output devices are found
0xD7 No console input devices are found
0xF2 Recovery process started
0xF9 Recovery capsule is not found
X11SPA-TF/X11SPA-T QUICK REFERENCE GUIDE M.2 SSD Installation Instructions
M.2 SSD Installation Instructions
M.2 SSD Installation
Warning: Be sure to install the M.2 SSD(s) prior to placing a motherboard into a chassis. Please refer to the
M.2 SSD installation and removal instructions as shown below and on the next page for proper procedures.
Unscrew the existing mounting screws
on the M.2 heatsink and then remove the
heatsink.
Remove the plastic liner from the M.2
heatsink thermal pad.
Be sure that the M.2 SSD is securely
fastened.
Unscrew the M.2 screw on the mother-
board. Insert the M.2 SSD into the M.2
socket at a 30 degree angle and press
down.
Tighten the M.2 SSD with the M.2 screw
removed in Step 2.
*The position of the screw is dependent on the M.2 SSD used.
(The default position supports 2280 form factor.)
Resecure the M.2 heatsink in place with
the mounting screws removed in Step 1.
1.
1
2
2.
3.
4.
5.
6.
M.2 SSD Removal Instructions
M.2 SSD Removal
X11SPA-TF/X11SPA-T QUICK REFERENCE GUIDE M.2 SSD Removal Instructions
Unscrew the existing mounting screws
on the M.2 heatsink and then remove
the heatsink.
Unscrew the existing M.2 screw on the
M.2 SSD.
Gently lift the M.2 SSD and be careful
not to damage the notch.
The M.2 SSD underneath the M.2
heatsink will be seen after the heatsink
is removed.
Pull the M.2 SSD straight out of the M.2
socket.
The M.2 SSD is now removed.
Note: The position of the standoff can be adjusted slightly to t your M.2 SSD if needed. (Refer to the FAQ on the
Supermicro website at https://www.supermicro.com/support/faqs/faq.cfm?faq=30404.)
1.
2.
3.
4.
5.
6.
X11SPA-TF/X11SPA-T QUICK REFERENCE GUIDE
Memory Population
Memory Population
Note: Unbalanced memory conguration decreases memory performance and is not recommended for Supermicro
motherboards.
DCPMM (Intel Optane™ DC Persistent Memory Modules) Population Tables for the X11SPA-TF/
X11SPA-T (w/12 Slots) based on the 82xx/62xx/52xx/42xx Platform
Symmetric Population within 1 CPU Socket
Modes P1-DIMMF1 P1-DIMMF2 P1-DIMME1 P1-DIMME2 P1-DIMMD1 P1-DIMMD2 P1-DIMMA2 P1-DIMMA1 P1-DIMMB2 P1-DIMMB1 P1-DIMMC2 P1-DIMMC1
Channel
Cong.
AD DRAM1 DCPMM DRAM1 DCPMM DRAM1 DCPMM DCPMM DRAM1 DCPMM DRAM1 DCPMM DRAM1 2-2-2
MM DRAM1 DCPMM DRAM1 DCPMM DRAM1 DCPMM DCPMM DRAM1 DCPMM DRAM1 DCPMM DRAM1 2-2-2
AD + MM DRAM3 DCPMM DRAM3 DCPMM DRAM3 DCPMM DCPMM DRAM3 DCPMM DRAM3 DCPMM DRAM3 2-2-2
AD DRAM1 - DRAM1 - DRAM1 DCPMM DCPMM DRAM1 - DRAM1 - DRAM1 2-1-1
MM DRAM2 - DRAM2 - DRAM2 DCPMM DCPMM DRAM2 - DRAM2 - DRAM2 2-1-1
AD + MM DRAM3 - DRAM3 - DRAM3 DCPMM DCPMM DRAM3 - DRAM3 - DRAM3 2-1-1
AD DRAM1 - DRAM1 DCPMM DRAM1 DCPMM DCPMM DRAM1 DCPMM DRAM1 - DRAM1 2-2-1
MM DRAM1 - DRAM1 DCPMM DRAM1 DCPMM DCPMM DRAM1 DCPMM DRAM1 - DRAM1 2-2-1
AD + MM DRAM3 - DRAM3 DCPMM DRAM3 DCPMM DCPMM DRAM3 DCPMM DRAM3 - DRAM3 2-2-1
AD DCPMM - DRAM1 - DRAM1 - - DRAM1 - DRAM1 - DCPMM 1-1-1
MM DCPMM - DRAM1 - DRAM1 - - DRAM1 - DRAM1 - DCPMM 1-1-1
AD + MM DCPMM - DRAM3 - DRAM3 - - DRAM3 - DRAM3 - DCPMM 1-1-1
AD DCPMM - DRAM1 DRAM1 DRAM1 DRAM1 DRAM1 DRAM1 DRAM1 DRAM1 - DCPMM 2-2-1
Asymmetric Population within 1 CPU Socket
Modes P1-DIMMF1 P1-DIMMF2 P1-DIMME1 P1-DIMME2 P1-DIMMD1 P1-DIMMD2 P1-DIMMA2 P1-DIMMA1 P1-DIMMB2 P1-DIMMB1 P1-DIMMC2 P1-DIMMC1
Channel
Cong.
AD DRAM1 - DRAM1 - DRAM1 - DCPMM DRAM1 - DRAM1 - DRAM1 2/1-1-1
AD* DRAM1 - DRAM1 - DRAM1 - DCPMM DRAM1 - DRAM1 - DRAM1 2/1-1-1
Legend (for the two tables above)
DDR4 Type Capacity
DRAM1 RDIMM 3DS RDIMM LRDIMM 3DS LRDIMM
Refer to Validation Matrix (DDR4 DIMMs
validated with DCPMM) below.
DRAM2 RDIMM - -
DRAM3 RDIMM 3DS RDIMM LRDIMM -
Notication for the Mounting Holes
Note: Before assembling the motherboard, pay attention to the location of mounting holes. Please select the chassis
which ts the mounting hole locations of this motherboard. Refer to the illustration below for the location details.
X11SPA-TF/X11SPA-T QUICK REFERENCE GUIDE Notication for the Mounting Holes
Notes
X11SPA-TF/X11SPA-T QUICK REFERENCE GUIDE Notes
X11SPA-TF/X11SPA-T
Quick RefeRence Guide Rev. 1.0b
S
UPERMICR
R
1
DESIGNED IN USA
X11SPA-TF
REV:1.01
MAC CODE
+
A C
A
C
C
A
Intel C621
ASPEED
AST2500
PLX
PEX8747
BIOS
LICENSE
IPMI CODE
BAR CODE
MAC CODE
RAID Key Header
USB3.1 Gen.1
USB3.1 Gen.1
USB3.1 Gen.2
USB3.1 Gen.2
USB3.1 Gen.2
USB3.1 Gen.1
JPAC1
IPMI
USB10 (3.1)
(3.1)USB11
USB0/1
(3.0)USB2/3
UID-SWUID-LED
AUDIO FP
USB4/5(3.0)
LAN2
USB6/7 (3.0)
IPMI_LAN
COM1
VGA
LAN1
(3.1)USB8/9
JPI2C1
JSD1
JPME2
JPG1
JWD1
JL1
JD1
12V_PUMP_PWR1
CPU SLOT1 PCI-E 3.0 x16
CPU SLOT2 PCI-E 3.0 x8
CPU SLOT3 PCI-E 3.0 x16
CPU SLOT4 PCI-E 3.0 x8
JSPDIF_OUT
CPU SLOT5 PCI-E 3.0 x16
CPU SLOT6 PCI-E 3.0 x8
CPU SLOT7 PCI-E 3.0 x16
JPWR4
HD AUDIO
FAN C
FAN D
JPL2
FAN6
FAN5
FAN4
JVRM1
JPWR3
JP5
JPUSB1
COM2
J9701
M.2-C04
PCI-E 3.0 x4
PCI-E 3.0 x4
M.2-C03
JOH1-OH
J9702
M.2-C02
PCI-E 3.0 x4
DIMMF1
DIMME1
DIMMF2
DIMME2
DIMMD1
DIMMD2
DIMMB1
DIMMA2
DIMMA1
DIMMB2
DIMMC1
DIMMC2
JTPM1
JRK1
JSD2
I-SATA0
I-SATA1 I-SATA3
I-SATA2 I-SATA4
I-SATA5
I-SATA6
I-SATA7
I-SGPIO2
FAN B FAN A
I-SGPIO1
M.2-C01
PCI-E 3.0 x4
JP4
FAN1
FAN2
JF1
JSTBY1
JPWR2
JIPMB1
BATTERY
JPWR1
FAN3
JPL1
LEDPWR
LEDBMC
Universal ID
A
C
C
A
A
C
A
C
LE3
LE4
LE5
LE6
Motherboard Layout and Features
= mounting hole
LGA 3647
I/O BACK PANEL
Package contents
• One (1) Supermicro Motherboard
• Six (6) SATA Cables
• One (1) I/O Shield
• One (1) Quick Reference Guide
• One (1) GPU to CPU Power Cable
Connector Description
12V_PUMP_PWR1 12V 4-pin Power Connector for CPU Liquid Cooling Pump
AUDIO FP Front Panel Audio Header
BATTERY Onboard Battery
COM1/COM2 COM1: COM Port (Back Panel), COM2: COM Header
CPU SLOT1/3/5/7 PCI-E 3.0 x16
PCI-E x16 Slots (PCI-E x16 link)
*PCI-E SLOT1 will change to PCI-E x8 link when either M.2-C03 or M.2-C04 is populated with an
SSD. PCI-E SLOT1 will be completely disabled when either M.2-C01 or M.2-C02 is populated with
an SSD.
CPU SLOT2/4/6 PCI-E 3.0 x8 (IN x16) PCI-E x16 Slots (PCI-E x8 link)
FAN1 ~ 6 CPU Fan Headers
FAN A ~ D
System Fan Headers
*The initial system fan speed must not be lower than 600 RPM.
HD AUDIO Back Panel High Denition Audio
IPMI_LAN
Dedicated IPMI LAN Port
*For IPMI support, X11SPA-TF is via SPS, whereas X11SPA-T is via ME.
I-SATA0~7 Intel Serial ATA (SATA 3.0) Ports 0~7 (6Gb/sec)
I-SGPIO1/I-SGPIO2 Serial General Purpose I/O Headers
JD1 Speaker/Power LED Indicator
JF1 Front Control Panel Header
JIPMB1 4-pin External I2C Header (for an IPMI card)
JL1 Chassis Intrusion Header
JOH1-OH Overheat LED Indicator
JP4/JP5 JP4: Enable/Disable USB10/11, JP5: Enable/Disable USB8/9
JPI2C1 Power Supply SMBus I2C Header
JPUSB1 Enable/Disable USB6/7 WakeUp
JPWR1/3/4 +12V 8-pin CPU Power Connectors (Required)
JPWR2 24-pin ATX Main Power Connector (Required)
JRK1
Intel RAID Key Header
*A VROC hardware key is required to enable an M.2 RAID card.
JSD1/JSD2 SATA DOM (Disk-On-Module) Power Connectors
JSPDIF_OUT Sony/Philips Digital Interface (S/PDIF) Out Header
JSTBY1 Standby Power Header (5V)
JTPM1 Trusted Platform Module (TPM)
LAN1/LAN2 RJ45 1GbE/10GbE LAN Ports
M.2-C01/C02/C03/C04 PCI-E 3.0 x4
PCI-E M.2 Connectors (Small Form Factor Devices and Other Portable
Devices for High Speed NVMe SSDs)
UID-SW Unit Identier (UID) Switch
USB0/1 Front Access USB 2.0 Header
USB2/3 Front Access USB 3.1 Gen1 Header
USB4/5, USB6/7
Back Panel USB 3.1 Gen1 Ports
*X11SPA-TF and X11SPA-T do not support S3 or S4.
*Either USB4/5 or USB6/7 will support standby power.
USB8/9 Back Panel USB 3.1 Gen2 Ports
USB10 Front Access USB 3.1 Gen2 Header
USB11 Front Access USB 3.1 Gen2 Port (Type A)
VGA VGA Port
Jumpers and Connectors
Jumpers
Jumper Description Default
J9701/J9702 Manufacturing Mode Pins 1-2 (Normal)
JPAC1 Audio Enable/Disable Pins 1-2 (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1/JPL2 LAN1/LAN2 Enable/Disable Pins 1-2 (Enabled)
JPME2 Intel Manufacturing Mode Pins 1-2 (Normal)
JWD1 Watch Dog Function Enable Pins 1-2 (RST)
Connectors
ContaCt InformatIon
• www.supermicro.com (Email: [email protected])
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: https://www.supermicro.com/wftp/driver/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
The X11SPA-TF/X11SPA-T motherboard supports an Intel® Xeon® Scalable-SP or 2nd Generation Intel Xeon
Scalable-SP processor, up to 768GB of ECC RDIMM, 3TB of 3DS RDIMM, 1.5TB of LRDIMM, and 3TB of 3DS
LRDIMM DDR4 (288-pin) ECC memory with speeds of up to 2933MHz (2DPC) in twelve memory slots. Populating
these DIMM slots with a pair of memory modules of the same type and size will result in interleaved memory, which
will improve memory performance. (1DPC and 2DPC are recommended for memory installation. Only selected 2nd
Gen Intel Xeon Scalable-SP processors support Intel Optane™ DC Persistent Memory Modules.)
Notes: 1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates,
please refer to our website at http://www.supermicro.com/products/motherboard.
2) Always connect the power cord last, and always remove it before adding, removing, or changing any hardware components.
DIMM Memory Installation
Towards the CPU
DIMME1 (Blue Slot)
DIMMD1 (Blue Slot)
DIMMD2 (Black Slot)
DIMME2 (Black Slot)
DIMMF1 (Blue Slot)
DIMMF2 (Black Slot)
Memory Population Guidelines
• Always use DDR4 DIMM modules of the same size, type, and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the slowest DIMM.
1 CPU, 12-DIMM Slots
Number of DIMMs Memory Population Sequence
1 DIMMA1
2 DIMMA1,DIMMD1
3 DIMMA1,DIMMB1,DIMMD1
4 DIMMA1,DIMMB1,DIMMD1,DIMME1
5 DIMMA1,DIMMB1,DIMMC1,DIMMD1,DIMME1
6 DIMMA1,DIMMB1,DIMMC1,DIMMD1,DIMME1,DIMMF1
7 DIMMA1,DIMMA2,DIMMB1,DIMMC1,DIMMD1,DIMME1,DIMMF1
8 DIMMA1,DIMMA2,DIMMB1,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMMF1
9 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMMF1
10 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1
11 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMC2,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1
12 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMC2,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1,DIMMF2
Note: In a given channel, the black slot can be enabled only when the blue slot is populated rst.
LED Indicators
LED Description Color/State
LE3/4/5/6 M.2 LED Blinking Green: Device Working
LEDBMC BMC Heartbeat LED Blinking Green: BMC Normal
LEDPWR Onboard Power LED Solid Green: Power On
UID-LED Unit Identier (UID) LED Blue on: Unit Identied
LED Indicators
CPU & Memory Support
CPU & Memory Support
MNL-2173-QRG-10b
© 2019 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Super-
micro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing;
however, it is not guaranteed.
Notes
• Graphics shown in this quick reference guide are for illustration only. Your components may or
may not look exactly the same as drawings shown in this guide.
• Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, LED
indicators, memory support and CPU/motherboard installation instructions.
Front Control Panel (JF1)
CPU and PHM Installation
Back Panel I/O Connectors
A. 1Gb RJ45 Port 1 G. USB 3.1 Gen1 Port 7 M. Surround Out
B. USB 3.1 Gen2 Port 9 H. USB 3.1 Gen1 Port 6 N. S/PDIF Out
C. USB 3.1 Gen2 Port 8 (Type C) I. 10Gb RJ45 Port 2 O. Line In
D. COM1 Port J. USB 3.1 Gen1 Port 5 P. Line Out
E. VGA Port K. USB 3.1 Gen1 Port 4 Q. Mic In
F. Dedicated IPMI LAN Port L. Center/LFE Out R. UID Switch
Power Button
UID-LED
NIC1 Active LED
Reset Button
HDD LED
PWR LED
Reset
PWR
P3V3_STBY_UID SW
P3V3_STBY
Ground
19
X
Ground
X
P3V3_STBY
20
1 2
Ground
Power Fail LED
NIC2 Active LED
SW_NMI_N
P3V3
OH/Fan Fail LED
P3V3
A
A
B
B
Pin 1
Align CPU Pin 1
CPU (Upside Down)
with CPU LGA Lands up
Processor Carrier
(Upside Down)
Align Point B of the CPU and
Point B of the Processor Carrier
Align Point A of the CPU and
Point A of the Processor Carrier
1
1
Assemble the processor carrier assembly by
inserting the CPU into the processor carrier.
Heatsink
(Upside Down)
1
2
1
2
Remaining plastic clips snap
into the other corner holes
of the heatsink
Plastic clips 1 and 2 lock
outside the heatsink’s
mounting holes
1
2
Triangle on the CPU
Triangle on the
Processor Carrier
1
2
To form the processor heatsink module (PHM),
mount the processor carrier assembly onto the
heatsink and snap into place.
1
3
After assembling the PHM, mount it onto the CPU socket of the
motherboard. Use a T-30 Torx-bit screwdriver to gradually install four
screws into the mounting holes from #1-4.
#1
#2
#3
#4
Small Guide Post
Large Guide Post
Oval D
T30 Torx Screwdriver
Use a torque
of 12 lbf-in
Oval C
Printed Triangle
Mounting the Processor Heatsink Module
onto the CPU socket (on the motherboard)
Tighten the screws in
the sequence of 1, 2, 3, 4
G
H
I
J
K
L
A
B
C
D
E
F
M
X11SPA-TF/-T
N
O
P
Q
R
美超微電腦股份有限公司
X11SPA-TF/X11SPA-T
快速參考指南版本1.0b
S
UPERMICR
R
1
DESIGNED IN USA
X11SPA-TF
REV:1.01
MAC CODE
+
A C
A
C
C
A
Intel C621
ASPEED
AST2500
PLX
PEX8747
BIOS
LICENSE
IPMI CODE
BAR CODE
MAC CODE
RAID Key Header
USB3.1 Gen.1
USB3.1 Gen.1
USB3.1 Gen.2
USB3.1 Gen.2
USB3.1 Gen.2
USB3.1 Gen.1
JPAC1
IPMI
USB10 (3.1)
(3.1)USB11
USB0/1
(3.0)USB2/3
UID-SWUID-LED
AUDIO FP
USB4/5(3.0)
LAN2
USB6/7 (3.0)
IPMI_LAN
COM1
VGA
LAN1
(3.1)USB8/9
JPI2C1
JSD1
JPME2
JPG1
JWD1
JL1
JD1
12V_PUMP_PWR1
CPU SLOT1 PCI-E 3.0 x16
CPU SLOT2 PCI-E 3.0 x8
CPU SLOT3 PCI-E 3.0 x16
CPU SLOT4 PCI-E 3.0 x8
JSPDIF_OUT
CPU SLOT5 PCI-E 3.0 x16
CPU SLOT6 PCI-E 3.0 x8
CPU SLOT7 PCI-E 3.0 x16
JPWR4
HD AUDIO
FAN C
FAN D
JPL2
FAN6
FAN5
FAN4
JVRM1
JPWR3
JP5
JPUSB1
COM2
J9701
M.2-C04
PCI-E 3.0 x4
PCI-E 3.0 x4
M.2-C03
JOH1-OH
J9702
M.2-C02
PCI-E 3.0 x4
DIMMF1
DIMME1
DIMMF2
DIMME2
DIMMD1
DIMMD2
DIMMB1
DIMMA2
DIMMA1
DIMMB2
DIMMC1
DIMMC2
JTPM1
JRK1
JSD2
I-SATA0
I-SATA1 I-SATA3
I-SATA2 I-SATA4
I-SATA5
I-SATA6
I-SATA7
I-SGPIO2
FAN B FAN A
I-SGPIO1
M.2-C01
PCI-E 3.0 x4
JP4
FAN1
FAN2
JF1
JSTBY1
JPWR2
JIPMB1
BATTERY
JPWR1
FAN3
JPL1
LEDPWR
LEDBMC
Universal ID
A
C
C
A
A
C
A
C
LE3
LE4
LE5
LE6
主機板元件配置圖
= 裝機孔
LGA 3647
I/O BACK PANEL
單一主機板包裝盒內容清單
• Supermicro主機板 x1
• SATA訊號線 x6
• 後檔板 x1
• 快速參考指南 x1
• GPU轉CPU電源線 x1
連接埠 說明
12V_PUMP_PWR1
4針腳12V水冷幫浦電源插座
AUDIO FP
前面板音效接頭
BATTERY
內建電池
COM1/COM2
COM1：COM連接埠（背板），COM2：COM接頭
CPU SLOT1/3/5/7 PCI-E 3.0 x16
PCI-E x16插槽，支援PCI-E 3.0 x16運 作 效 能 規 格
*若M.2-C03或M.2-C04其中之一安裝固態硬碟時，PCI-E SLOT1將以PCI-E x8運行。若M.2-C01或
M.2-C02之一安裝固態硬碟時，PCI-E SLOT1將無法作用。
CPU SLOT2/4/6 PCI-E 3.0 x8 (IN x16)
PCI-E x16插槽，支援PCI-E 3.0 x8運作效能規格
FAN1 ~ 6
中央處理器（CPU）風扇接頭
FAN A ~ D
系統風扇接頭
*系統風扇的起始速度不可低於600 RPM。
HD AUDIO
背板高清晰音效插孔
IPMI_LAN
IPMI網路連接埠
*X11SPA-TF的BIOS韌體是SPS，而X11SPA-T的BIOS韌體是ME。
I-SATA0~7
Intel序列ATA介面（SATA 3.0）連接埠0~7（6Gb/秒）
I-SGPIO1/I-SGPIO2
序列通用I/O傳輸插座
JD1
喇叭/電源指示燈接頭
JF1
前控制面板接頭
JIPMB1
4針腳外接I2C接頭（僅適用於IPMI）
JL1
機殼防盜裝置接頭
JOH1-OH
過熱顯示指示燈接頭
JP4/JP5
JP4：啟用/停用USB10/11，JP5：啟用/停用USB8/9
JPI2C1
電源供應SMBus I2C接頭
JPUSB1
啟用/停用USB6/7喚醒
JPWR1/3/4
8針腳+12伏特CPU電源連接埠（必備）
JPWR2
24針腳ATX主電源連接埠（必備）
JRK1
Intel RAID Key接頭
*若要啟動M.2 RAID功能需加裝VROC hardware key。
JSD1/JSD2
SATA DOM（磁碟模組）電源連接埠
JSPDIF_OUT
S/PDIF（索尼/飛利浦數位傳輸介面）輸出接頭
JSTBY1
待機電源接頭（5V）
JTPM1
TPM信任平台模組接頭
LAN1/LAN2
RJ45 1GbE/10GbE乙太網路線連接埠
M.2-C01/C02/C03/C04 PCI-E 3.0 x4
PCI-E M.2介面連接埠，適用具高速傳輸NVMe介面之小尺寸以及其他可攜式
M.2固態硬碟
*PCI-E為電腦匯流的一種規格，M.2為固態硬碟的一種傳輸介面，而NVMe為非揮發性記憶體儲存裝
置的一種標準。
UID-SW
單位識別按鈕
USB0/1
前面板USB 2.0規格連接埠（註：USB 完整譯名為「通用序列匯流排」）
USB2/3
前面板USB 3.1 Gen1規格連接埠
USB4/5, USB6/7
背板USB 3.1 Gen1規格連接埠
*X11S PA-TF和X11SPA-T皆不支援S3或S4。
*USB4/5或USB6/7其中之一 可 支 援 待 機 電 源。
USB8/9
背板USB 3.1 Gen2規格連接埠
USB10
前面板USB 3.1 Gen2規格連接埠
USB11
前面板USB 3.1 Gen2規格連接埠（Type A）
VGA
VGA連接埠
跳線器/連接埠
跳線器 (Jumper)
跳線器 說明 預設值
J9701/J9702
工廠製造設定模式 針腳1-2（正常）
JPAC1
啟用/停用音源 針腳1-2（啟用）
JPG1
啟用/停用VGA 針腳1-2（啟用）
JPL1/JPL2
啟用/停用LAN1/LAN2 針腳1-2（啟用）
JPME2
Intel製造模式 針腳1-2（正常）
JWD1
啟動系統監控（Watch Dog）功能 針腳1-2（重設）
連接埠 (Connector)
線上技術支援及下載
• 聯絡我們（技術支援信箱）：www.supermicro.com （Email: [email protected]）
• 產品手冊文件：http://www.supermicro.com/support/manuals
• 驅動程式及工具程式：https://www.supermicro.com/wftp/driver/
• 產品安全性須知：http://www.supermicro.com/about/policies/safety_information.cfm
本主機板
X11S PA -TF/X11SPA-T
支援
Intel® Xeon® Scalable-SP系列和第二代Intel Xeon Scalable-SP系列
處理器。記憶
體支援
Unbuffered（UDIMM）ECC/Non-ECC DDR4
，容量最高可達
768GB ECC RDIMM
，
3TB 3DS RDIMM
，
1.5TB
LRDIMM
，
和3TB 3DS LRDIMM DDR4
，及十二個傳輸頻率最高可達 2933MHz
（
2DPC
）
288支針腳的記憶體插槽。欲取
得雙通道效能，請安裝成對相同型號與速度之記憶體。
（建議使用
1DPC
或
2DPC
。僅部分的
第二代Intel Xeon Scalable-SP系列
處理器可支援
Intel Optane™ DC
持續性記憶體模組。）
註：1) 請安裝使用本公司所認可的記憶體模組以達記憶體模組最佳化。更多的記憶體模組相關訊息，請參閱本公司
網頁
（
http://www.supermicro.com/products/motherboard
）
。
2) 增加、移除和更換任何硬體元件前，請務必先拔掉電源線。待確實完成所有程序後，再重新連接電源線。
3) Unbuffered DIMM，或做UDIMM，為「無緩衝雙通道記憶體模組」；ECC是Error Correction Code的縮寫，
中譯為「錯誤修正碼」；DDR為「雙倍速動態隨機存取記憶體」。
記憶體模組（DIMM）安裝方式
此面朝向中央處理器
DIMMF1（藍色插槽）
DIMME1（藍色插槽）
DIMME2（黑色插槽）
DIMMF2（黑色插槽）
DIMMD1（藍色插槽）
DIMMD2（黑色插槽）
請依照以下說明及表格安裝記憶體模組：
• 請使用相同型號（DDR4 DIMM）與速度之記憶體。
• 若混合使用不同速度之記憶體，系統將依較低的記憶體速度執行。
1個中央處理器，12個記憶體插槽
DIMM的數量 建議插槽使用方式
1 DIMMA1
2 DIMMA1,DIMMD1
3 DIMMA1,DIMMB1,DIMMD1
4 DIMMA1,DIMMB1,DIMMD1,DIMME1
5 DIMMA1,DIMMB1,DIMMC1,DIMMD1,DIMME1
6 DIMMA1,DIMMB1,DIMMC1,DIMMD1,DIMME1,DIMMF1
7 DIMMA1,DIMMA2,DIMMB1,DIMMC1,DIMMD1,DIMME1,DIMMF1
8 DIMMA1,DIMMA2,DIMMB1,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMMF1
9 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMMF1
10 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1
11 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMC2,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1
12 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMC2,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1,DIMMF2
註
: 安裝記憶體時，只有當該通道的藍色插槽先裝記憶體後，黑色插槽才能發揮其效能。
LED指示燈
LED燈 說明 燈號顏色/情況
LE3/4/5/6
M.2指示燈 綠燈閃爍：M.2使用中
LEDBMC
BMC運作指示燈 綠燈閃爍：BMC正常
LEDPWR
內建電源指示燈 綠燈恆亮：開啟
UID-LED
單位識別指示燈 藍燈恆亮：識別中
LED指示燈
中央處理器和記憶體支援
MNL-2173-QRG-10b
備註
• 快速參考指南中的圖例僅供安裝及操作說明使用，可能與實際產品外觀不同。
• 欲知更多跳線器/連接埠/指示燈/記憶體/主機板/中央處理器的安裝相關資訊，請參閱
《Supermicro X11SpA-TF/X11SpA-T使用手冊》第二章。
© 2019 美超微股份有限公司（以下簡稱「本公司」）版權所有。未經本公司書面同意，嚴禁重製本文件部分或全部內容。所有商標均為所屬公司所有，
所有提供資訊於印刷之際視為但不保證正確。
前控制面板配置（JF1）
中央處理器與散熱器安裝方式
背板輸出/輸入連接埠
A. RJ45 1Gb LAN1乙太網路線連接埠 G. USB 3.1 Gen1連接埠7 M. 環繞聲道輸出
B. USB 3.1 Gen2連接埠9 H. USB 3.1 Gen1連接埠6 N. S/PDIF輸出
C. USB 3.1 Gen2連接埠8（Type C） I. RJ45 10Gb LAN2乙太網路線連接埠 O. 音效輸入
D. COM1序列連接埠 J. USB 3.1 Gen1連接埠5 P. 音效輸出
E. VGA連接埠 K. USB 3.1 Gen1連接埠4 Q. 麥克風插孔
F. IPMI網路連接埠 L. 中央/低音聲道輸出 R. 單位識別按紐
Power Button
UID-LED
NIC1 Active LED
Reset Button
HDD LED
PWR LED
Reset
PWR
P3V3_STBY_UID SW
P3V3_STBY
Ground
19
X
Ground
X
P3V3_STBY
20
1 2
Ground
Power Fail LED
NIC2 Active LED
SW_NMI_N
P3V3
OH/Fan Fail LED
P3V3
單位識別指示燈
網卡1 Active指示燈
硬碟指示燈
電源指示燈
單位識別按紐
P3V3待機電源
接地
19
X
接地
X
P3V3待機電源
20
1 2
接地
電源故障指示燈
網卡2 Active指示燈
非可遮蔽中斷
P3V3
過熱/風扇故障指示燈
P3V3
電源鍵
電源
重設
重設鍵
X11SPA-TF/-T
A
A
B
B
針腳 1
對齊CPU針腳 1
CPU反面
(CPU LGA 針腳面朝上)
處理器固定板 (反面)
將CPU上的A點對齊
處理器固定板上的A點
將CPU上的B點對齊
處理器固定板上的B點
1
1
依照下方圖示及說明將CPU安裝至處理器固定板上。
散熱器
(反面)
1
2
1
2
Remaining plastic clips snap
into the other corner holes
of the heatsink
Plastic clips 1 and 2 lock
outside the heatsink’s
mounting holes
1
2
CPU上的三角形
處理器固定板上的三角形
1
2
安裝處理器散熱模組時，將安裝好的CPU固定板置於
散熱器之上。
1
3
安裝好處理器散熱模組後，將處理器散熱模組裝在主機板的CPU
插槽之上。使用六星型螺絲起子，慢慢依序將四個螺絲拴入安裝
孔#1-4中。
#1
#2
#3
#4
小導柱
大導柱
橢圓形D孔
使用六星型螺絲起子
橢圓形C孔
三角圖示
安裝處理器的散熱模組於CPU插槽上
(主機板上)
依照順序栓緊螺絲 #1, 2, 3, 4
G
H
I
J
K
L
A
B
C
D
E
F
M
N
O
P
Q
R
美超微电脑股份有限公司
X11SPA-TF/X11SPA-T
快速参考指南版本1.0b
S
UPERMICR
R
1
DESIGNED IN USA
X11SPA-TF
REV:1.01
MAC CODE
+
A C
A
C
C
A
Intel C621
ASPEED
AST2500
PLX
PEX8747
BIOS
LICENSE
IPMI CODE
BAR CODE
MAC CODE
RAID Key Header
USB3.1 Gen.1
USB3.1 Gen.1
USB3.1 Gen.2
USB3.1 Gen.2
USB3.1 Gen.2
USB3.1 Gen.1
JPAC1
IPMI
USB10 (3.1)
(3.1)USB11
USB0/1
(3.0)USB2/3
UID-SWUID-LED
AUDIO FP
USB4/5(3.0)
LAN2
USB6/7 (3.0)
IPMI_LAN
COM1
VGA
LAN1
(3.1)USB8/9
JPI2C1
JSD1
JPME2
JPG1
JWD1
JL1
JD1
12V_PUMP_PWR1
CPU SLOT1 PCI-E 3.0 x16
CPU SLOT2 PCI-E 3.0 x8
CPU SLOT3 PCI-E 3.0 x16
CPU SLOT4 PCI-E 3.0 x8
JSPDIF_OUT
CPU SLOT5 PCI-E 3.0 x16
CPU SLOT6 PCI-E 3.0 x8
CPU SLOT7 PCI-E 3.0 x16
JPWR4
HD AUDIO
FAN C
FAN D
JPL2
FAN6
FAN5
FAN4
JVRM1
JPWR3
JP5
JPUSB1
COM2
J9701
M.2-C04
PCI-E 3.0 x4
PCI-E 3.0 x4
M.2-C03
JOH1-OH
J9702
M.2-C02
PCI-E 3.0 x4
DIMMF1
DIMME1
DIMMF2
DIMME2
DIMMD1
DIMMD2
DIMMB1
DIMMA2
DIMMA1
DIMMB2
DIMMC1
DIMMC2
JTPM1
JRK1
JSD2
I-SATA0
I-SATA1 I-SATA3
I-SATA2 I-SATA4
I-SATA5
I-SATA6
I-SATA7
I-SGPIO2
FAN B FAN A
I-SGPIO1
M.2-C01
PCI-E 3.0 x4
JP4
FAN1
FAN2
JF1
JSTBY1
JPWR2
JIPMB1
BATTERY
JPWR1
FAN3
JPL1
LEDPWR
LEDBMC
Universal ID
A
C
C
A
A
C
A
C
LE3
LE4
LE5
LE6
主板元件配置图
= 装机孔
LGA 3647
I/O BACK PANEL
• 快速参考指南 x1
• GPU转CPU电源线 x1
• Supermicro主板 x1
• SATA数据线 x6
• 后挡板 x1
单一主板包装盒內容清单
接口 说明
12V_PUMP_PWR1
4针脚12V水冷泵浦电源插座
AUDIO FP
前面板音效接口
BATTERY
內建电池
COM1/COM2
COM1：COM接口（背板），COM2：COM接口
CPU SLOT1/3/5/7 PCI-E 3.0 x16
PCI-E x16插槽，支持PCI-E 3.0 x16总 线 规 格
*若M.2-C03或M.2-C04其中之一安装固态硬盘时，PCI-E SLOT1将以PCI-E x8运行。若M.2-C01或
M.2-C02之一安装固态硬盘时，PCI-E SLOT1将不可用。
CPU SLOT2/4/6 PCI-E 3.0 x8 (IN x16)
PCI-E x16插槽，支持PCI-E 3.0 x8总线规格
FAN1 ~ 6
中央处理器（CPU）风扇接口
FAN A ~ D
系统风扇接口
*系统风扇的起始速度不可低于600 RPM。
HD AUDIO
背板高清音效插孔
IPMI_LAN
IPMI网络接口
*X11SPA-TF的BIOS固件是SPS，而X11SPA-T的BIOS固件是ME。
I-SATA0~7
Intel串行ATA介面（SATA 3.0）接口0~7（6Gb/秒）
I-SGPIO1/I-SGPIO2
串行通用I/O传输插座
JD1
喇叭/电源指示灯接口
JF1
前控制面板接口
JIPMB1
4针脚外接I2C接口（仅适用于IPMI）
JL1
机壳防盗装置接口
JOH1-OH
过热显示指示灯接口
JP4/JP5
JP4：启用/停用USB10/11，JP5：启用/停用USB8/9
JPI2C1
电源SMBus I2C接口
JPUSB1
启用/停用USB6/7喚醒
JPWR1/3/4
8针脚+12伏特CPU供电接口（必备）
JPWR2
24针脚ATX主电源接口（必备）
JRK1
Intel RAID Key接口
*若要启动M.2 RAID功能需加装VROC hardware key。
JSD1/JSD2
SATA DOM（磁盘模组）电源接口
JSPDIF_OUT
S/PDIF（索尼/飞利浦数字传输介面）输出接口
JSTBY1
待机电源接口（5V）
JTPM1
TPM信任平台模组接口
LAN1/LAN2
RJ45 1GbE/10GbE乙太网络接口
M.2-C01/C02/C03/C04 PCI-E 3.0 x4
PCI-E M.2接口，适用具高速传输NVMe介面之小尺寸以及其他可携式M.2固
态硬盘
*PCI-E为电脑总线的一种规格，M.2为固态硬盘的一种传输介面，而NVMe为非易失性存储装置的一
种标准。
UID-SW
系统识别按钮
USB0/1
前面板USB 2.0接口（注：USB 完整译名为「通用串行总线」）
USB2/3
前面板USB 3.1 Gen1接口
USB4/5, USB6/7
背板USB 3.1 Gen1接口
*X11SPA-TF和X11SPA-T皆不支持S3或S4。
*USB4/5或USB6/7其中之一可支持待机电源。
USB8/9
背板USB 3.1 Gen2接口
USB10
前面板USB 3.1 Gen2接口
USB11
前面板USB 3.1 Gen2接口（Type A）
VGA
VGA接口
跳帽/接口
跳帽（Jumper）
跳帽 说明 预设值
J9701/J9702
工厂制造设置模式 针脚1-2（正常）
JPAC1
启用/停用音源 针脚1-2（启用）
JPG1
启用/停用VGA 针脚1-2（启用）
JPL1/JPL2
启用/停用LAN1/LAN2 针脚1-2（启用）
JPME2
Intel制造模式 针脚1-2（正常）
JWD1
启用看门狗（Watch Dog）功能 针脚1-2（重启）
接口（Connector）
• 联络我们（技术支持信箱）：www.supermicro.com （Email: [email protected]）
• 产品手冊文件：http://www.supermicro.com/support/manuals
• 驱动程序及工具程序：https://www.supermicro.com/wftp/driver/
• 产品安全性须知：http://www.supermicro.com/about/policies/safety_information.cfm
在线技术支持及下载
本主板
X11S PA -TF/X11SPA -T
支持
Intel®Xeon®Scalable-SP系列和第二代Intel Xeon Scalable-SP系列处
理
器。内存支持
Unbuffered（UDIMM）ECC/Non-ECC DDR4
，容量最高可达
768GB ECC RDIMM
，
3TB 3DS
RDIMM
，
1.5TB LRDIMM
，
和3TB 3DS LRDIMM DDR4
，及十二个传输频率最高可达
2933MHz（2DPC）288
支针脚内存插槽。欲取得双通道性能，请安装成对相同型号速度之内存。（注：建 议 使 用
1DPC
或
2DPC
。
仅部分的第二代
Intel Xeon Scalable-SP
系列处理器可支持
Intel Optane™ DC
数据中心级持久内存模块。）
注：1) 请安装使用本公司所认可的内存模組以达到内存性能最佳化。更多的内存模组相关信息，请 参 阅 本公司网页
（
http://www.supermicro.com/products/motherboard
）
。
2) 增加、移除和更换任何硬件前，请务必先拔掉电源线。待确认完成所有程序后，再重新连接电源线。
3) Unbuffered DIMM，或做UDIMM，为「无缓存双通道内存模组」；ECC是Error Correction Code的缩写，中
译为「错误修正码」；DDR为「双倍速动态随机存取内存」。
内存模组（DIMM）安装方式
此面朝向中央处理器
DIMMF1（蓝色插槽）
DIMME1（蓝色插槽）
DIMME2（黑色插槽）
DIMMF2（黑色插槽）
DIMMD1（蓝色插槽）
DIMMD2（黑色插槽）
请依照以下说明及表格安装内存模组：
• 请使用相同型号（DDR4 DIMM）与速度之内存。
• 若混合使用不同速度之内存，系统将依较低的内存速度运行。
1个中央处理器，12个内存插槽
DIMM的数量 建议插槽使用方式
1 DIMMA1
2 DIMMA1,DIMMD1
3 DIMMA1,DIMMB1,DIMMD1
4 DIMMA1,DIMMB1,DIMMD1,DIMME1
5 DIMMA1,DIMMB1,DIMMC1,DIMMD1,DIMME1
6 DIMMA1,DIMMB1,DIMMC1,DIMMD1,DIMME1,DIMMF1
7 DIMMA1,DIMMA2,DIMMB1,DIMMC1,DIMMD1,DIMME1,DIMMF1
8 DIMMA1,DIMMA2,DIMMB1,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMMF1
9 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMMF1
10 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1
11 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMC2,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1
12 DIMMA1,DIMMA2,DIMMB1,DIMMB2,DIMMC1,DIMMC2,DIMMD1,DIMMD2,DIMME1,DIMME2,DIMMF1,DIMMF2
注
: 安装内存時，只有当该通道的蓝色插槽先装内存后，黑色插槽才能使用。
LED指示灯
LED灯 说明 灯号顏色/情况
LE3/4/5/6
M.2指示灯 绿灯闪烁：M.2使用中
LEDBMC
BMC心跳指示灯 绿灯闪烁：BMC正常
LEDPWR
內建电源指示灯 绿灯恒亮：开启
UID-LED
系统识别指示灯 蓝灯恒亮：识别中
LED指示灯
中央处理器和内存支持
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
Supermicro X11SPA-TF Quick Reference Manual
- タイプ
- Quick Reference Manual
- このマニュアルも適しています
関連論文
-
Supermicro X11SCA-W Quick Reference Manual
-
-
-
-
-
-