Thrustmaster 4469021 ユーザーマニュアル

Europe, Middle East

ENGLISH

FRANÇAIS

DEUTSCH

NEDERLANDS

ITALIANO

ESPAÑOL

PORTUGUÊS

РУССКИЙ

ČESTINA

TÜRKÇE

POLSKI

SVENSKA

SUOMI

SLOVENCINA

MAGYAR NYELV

תירבע

ﺔﻴﺑﺮﻌﻟا

North America/

Norteamérica

ENGLISH

FRANÇAIS

ESPAÑOL

Latin America/

América Latina

ENGLISH

ESPAÑOL

PORTUGUÊS

Asia Pacic

日本語

简体中文

繁體中文

ENGLISH

1/24

FOR XBOX SERIES X|S / XBOX ONE

User Manual

WARNING:

To ensure that your TX Racing Wheel functions correctly

with games for XBOX SERIES X|S / XBOX ONE,

you may be required to install the games' automatic updates

(available when your games console is connected to the Internet).

2/24

TECHNICAL SPECIFICATIONS

1 Racing wheel base

2 Racing wheel

3 2 sequential gear shift levers (Up & Down)

4 Multidirectional D-Pad

5 Switch (3 positions)

6 MODE button + Red/Green indicator light

7 Xbox Guide button

8 White indicator light

9 Large threaded hole (for attachment system

and tightening screw)

10 Attachment system

11 Metal fastening screw

12 Thrustmaster Quick Release

13 Mains supply connector (type A or B)

(Varies from one country to another)

14 Racing wheel USB cable and connector

15 Gearbox connector (sold separately)

16 Pedal set connector

3/24

CONNECTING THE RACING WHEEL TO THE MAINS = PLEASE READ

BEFORE PROCEEDING!

Your racing wheel's power supply varies according to the country where you purchased your device.

The mains supply can be:

Internal, with:

* A power supply unit located directly inside the racing wheel's base, with a type A

connector

*A 220-240V mains power supply cable

= compatible only with a 220-240V electrical supply.

Never connect the 220-240V cable

to a 100-130V power outlet!

Never connect this cable to a mains power adapter!

Internal, with:

* A power supply unit located directly inside the racing wheel's base, with a type A

connector

*A 100-125V power supply cable

= compatible only with a 100-125V electrical supply.

Never connect the 100-125V cable

to a 220-240V power outlet!

Never connect this cable to a mains power adapter!

IMPORTANT: if you do not know which voltage is supplied in the area in which you are

using your racing wheel, please refer to your local electricity supplier.

External, with:

* An external power supply unit located on the racing wheel's base, with a type B connector

* A mains power supply cable

= compatible with all supply voltages, 110-240V.

4/24

WARNINGS

Before you use this product, please read this documentation carefully and keep it safe should you need to

consult it later.

Warning – Electric shock

* Store the product in a dry location and do not expose it to dust or sunlight.

* Respect the connection direction.

* Do not twist or pull the connectors and cables.

* Do not spill any liquid on the product or its connectors.

* Do not short-circuit the product.

* Never dismantle the product; do not throw it onto a fire and do not expose it to high temperatures.

* Do not use a power supply cable other than the one provided with your racing wheel.

* Do not use the mains power supply cable if the cable or the connectors are damaged, split or broken.

* Make sure that the mains power cable is properly inserted into the power outlet and the connector

located on the rear face of the racing wheel's base.

* Do not open. No user replaceable parts inside. Refer servicing to manufacturer, specified agency or

qualified technician.

* Only use attachments/accessories specified by the manufacturer.

* If the steering wheel is operating unusually (if it is emitting any abnormal sounds, heat or odors), stop

using it immediately, disconnect the power cable from the socket and disconnect the other cables.

* If you are not going to be using the steering wheel for an extended period, disconnect the mains adaptor

from the wall socket.

Air vents

Make sure that you do not block any of the air vents on the steering wheel base. For optimum ventilation,

respect the points below:

* Position the base at least 10 cm away from any wall surfaces.

* Do not place the base in any tight spaces.

* Do not cover the base.

* Do not let any dust build up on the air vents.

For safety reasons, never use the pedal set with bare feet or while wearing

only socks on your feet.

THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF

INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES.

Warning – Injuries due to force feedback and repeated movements

Playing with a force-feedback steering wheel may cause muscle or joint pain. To avoid any problems:

* Avoid lengthy gaming periods.

* Take 10 to 15 minute breaks after each hour of play.

* If you feel any fatigue or pain in your hands, wrists, arms, feet or legs, stop playing and rest for a few

hours before you start playing again.

5/24

Warning – Injuries due to force feedback and repeated movements (continued)

* If the symptoms or pain indicated above persist when you start playing again, stop playing and

consult your doctor.

* Keep out of children’s reach.

* During games, always leave both hands correctly positioned on the steering wheel without completely

letting go.

* During gameplay, never place your hands or your fingers under the pedals or anywhere near the

pedal set.

* During calibration and gameplay, never place your hand or your arm through the openings in the

racing wheel.

* Check the steering wheel base is carefully clamped as per manual’s instructions.

To be handled only by users

16 years of age or older

HEAVY PRODUCT

Be careful not to drop the product on

yourself or on anyone else!

ALWAYS NEVER NEVER

6/24

Warning – Pedal set pinch hazard when playing

* Keep the pedal set out of children’s reach.

* When playing, never place your fingers on or anywhere near the sides of the pedals.

* When playing, never leave your fingers on or anywhere near the pedals' rear base.

* When playing, never place your fingers on or anywhere near the pedals' front base.

NEVER NEVER NEVER

Warning – Pedal set pinch hazard when not playing

* Store the pedal set in a safe place, and keep it out of children’s reach.

7/24

ATTACHING THE WHEEL TO ITS BASE

Align the connector locations using the arrows:

Base (1) connector: Arrow pointing upwards.

Racing wheel (2) connector: Arrow pointing upwards.

Once the connectors are correctly positioned, simply rotate the Thrustmaster Quick Release (12) device's

ring counterclockwise, while holding the racing wheel (2) in position.

Then, tighten the ring as much as you can; to do so, hold the ring in position and rotate the racing wheel

clockwise.

Once you have installed the wheel, rotate it 180° (when facing the wheel, the logo should be upside

down) to access the small attachment screw located on the Thrustmaster Quick Release (12) device. Use

a large cross-slot screwdriver to tighten the small attachment screw (do not use excessive force), turning

it clockwise.

Do not use excessive force when screwing the small attachment screw (using a cross-slot

screwdriver)!

Stop turning the screw as soon as you feel some resistance.

8/24

ATTACHING THE RACING WHEEL

Attaching the racing wheel to a table or a desktop

1. Place the racing wheel on a table or any other horizontal, flat and stable surface.

2. Insert the fastening screw (11) in the attachment system (10), then tighten the device by turning

the screw counterclockwise, so that it feeds into the large threaded hole (9) located beneath the

racing wheel, until the device is perfectly stable.

ALWAYS NEVER

WARNING: Never tighten the screw alone, without the attachment system!

(This could damage the racing wheel).

9/24

ATTACHMENT /

REMOVAL

DIRECTION

To tighten:

Turn the screw

counterclockwise

To release:

Turn the screw

clockwise

10/24

Attaching the racing wheel's base to a cockpit

1. Place the racing wheel's base on the cockpit shelf.

2. Drive two M6 screws (not included) through the cockpit shelf, then feed them into the two small

threaded holes located beneath the racing wheel.

Important: The length of the M6 screws should not exceed the thickness of the shelf + 12 mm;

longer screws could cause damage to internal components located in the racing wheel's base.

3. If required, tighten the standard attachment system by inserting the fastening screw in the large

threaded hole.

XBOX SERIES X|S / XBOX ONE MAPPING

PC MAPPING

11/24

UPDATING YOUR RACING WHEEL’S FIRMWARE

The firmware included in your racing wheel’s base can be updated to a more recent version featuring

product enhancements.

To display the firmware version that your racing wheel is currently using and update it if required: on

PC, visit https://support.thrustmaster.com. Click Racing Wheels / TX Racing Wheel LEATHER

Edition, then select Firmware and follow the instructions describing the download and installation

procedure.

SETTING UP THE RACING WHEEL FOR THE XBOX SERIES X|S / XBOX

ONE

1. Connect the pedal set to the connector (16) located at the back of the racing wheel's base.

2. Connect the power supply cable to the connector (13) located at the back of the racing wheel's

base.

3. Connect the power supply cable to a mains outlet with proper voltage specifications.

For more information about this, please refer to the CONNECTING THE RACING

WHEEL TO THE MAINS section, on page 3 in this manual.

4. Connect the racing wheel's USB connector (14) to one of the console's USB ports.

You are now ready to race!

AUTOMATIC RACING WHEEL AND PEDAL SET CALIBRATION

The racing wheel automatically self-calibrates when you connect the racing wheel to the mains and the

racing wheel's USB connector to the console.

During this phase, the racing wheel will rotate quickly towards the left and the right, covering a 900-

degree angle, before stopping at the center.

WARNING:

Never touch the racing wheel during the self-calibration phase!

(This could cause an incorrect calibration and/or personal injuries).

12/24

AUTOMATIC CALIBRATION OF THE PEDAL SET

Never connect the pedal set to the racing wheel's base (or disconnect it from the base) when it is

connected to the console or during gameplay (this could cause incorrect calibration).

Always connect the pedal set before connecting the racing wheel to the console.

Once the racing wheel's calibration is done and the game has been launched, the pedals are

automatically calibrated after a few presses.

WARNING:

Never press the pedals

during the racing wheel's self-calibration phase or while a game is loading!

(This could cause incorrect calibration)

If your racing wheel and pedal set do not operate correctly, or if calibration seems incorrect:

Turn off your console, disconnect your racing wheel entirely, reconnect all cables (using the mains

power supply cable and pedal set), then restart your console and your game.

INTERNAL TEMPERATURE SENSOR

For safety reasons, the racing wheel's base features a temperature sensor.

If the device's temperature becomes too high, your racing wheel can shut down suddenly.

In this event:

- Unplug the mains power supply cable and the device's USB connector.

- Wait for the racing wheel's base to cool down entirely.

- Then, reconnect the device.

13/24

MODE BUTTON AND INDICATOR LIGHT (6)

MODE button for the pedal set

You can electronically swap the accelerator and clutch pedals.

To do so, simply press the MODE button (6) for 2 seconds.

The racing wheel's internal memory stores whether the pedals have been swapped around or not.

ACCELERATOR AND CLUTCH PEDALS

Color of the MODE indicator light (6)

NORMAL RED

SWAPPED AROUND

GREEN

Other information regarding the MODE button

To learn more about the MODE button and indicator light, please visit

https://support.thrustmaster.com. Click Racing Wheels / TX Racing Wheel LEATHER Edition,

then select Manual or FAQ.

HELP FILES AND FAQS (NOT INCLUDED IN THIS MANUAL)

Please visit https://support.thrustmaster.com, click Racing Wheels / TX Racing Wheel LEATHER

Edition, then select Manual or FAQ.

14/24

15/24

TECHNICAL FEATURES

1 Metal support for conical stop

(not installed by default)

2 Conical stop

3 Attachment screw for metal support

4 2.5 mm Allen key (included)

5 Position adjustment nut for conical stop

6 Pedal arm

7 Plastic head support

8 Metal pedal head

16/24

WARNING

Before using this product, be sure to read these instructions carefully and save them for future reference.

For safety reasons, never use the pedal set with bare feet or while wearing

only socks on your feet.

THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF

INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES.

Warning – Pedal set pinching hazard during gaming sessions

* Keep the pedal set out of the reach of children.

* During gaming sessions, never place your fingers or thumbs on or near the sides of the pedals.

* During gaming sessions, never place your fingers or thumbs on or near the rear base of the pedals.

* During gaming sessions, never place your fingers or thumbs on or near the front base of the pedals.

NEVER

17/24

AUTOMATIC CALIBRATION OF PEDALS

IMPORTANT:

- Never connect or disconnect the pedal set from the base of the wheel when the wheel is

connected to the console or PC, or during gaming sessions, to avoid calibration problems.

= Always connect the pedal set to the wheel before connecting the wheel to the console or PC.

- Once the wheel has self-calibrated and the game has started, the pedals automatically calibrate

themselves after being pressed a few times.

- Never press on the pedals when the wheel is self-calibrating or when your game is starting up, to

avoid calibration problems.

- If the pedals are not functioning correctly or appear to be improperly calibrated, power off your

console, completely disconnect your wheel, then reconnect all of the cables (including the power

supply cable and the pedal set cable), power the console back on and restart your game.

ATTACHING THE PEDAL SET TO A COCKPIT

- Attach the pedal set using the small screw threads located on the underside of the pedal set.

- Screw two M6 screws (not included) into the cockpit’s pedal support plate and into the two small

screw threads located on the underside of the pedal set.

Important: The length of the two M6 screws must not exceed the thickness of the cockpit’s pedal

support plate plus an additional 10 mm, to avoid damaging the pedal set’s internal components.

18/24

ADJUSTING THE PEDAL SET

Each of the three pedals includes:

- A metal head (8) with multiple perforations (nine for the accelerator – six for the brake – six for the

clutch).

- A plastic head support (7) (placed between the head and the arm) with four perforations.

- A pedal arm (6) with two perforations.

ATTENTION: To avoid any calibration problems, be sure to always disconnect your wheel’s

USB cable from the console or PC before making any adjustments to your pedal set.

Adjusting the HEIGHT of the accelerator pedal

- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and

its support (7) in place.

- Select your preferred height position, then replace and re-tighten the screws so that the metal

head (8) and its support (7) are held firmly in place.

Low position (default)

High position

19/24

Adjusting the SPACING of the three pedals

- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and

its support (7) in place.

- Select your preferred position (to the left, centered, or to the right), then replace and re-tighten the

screws so that the metal head (8) and its support (7) are held firmly in place.

Examples illustrating the brake pedal:

Left position Centered position (default) Right position

Number of possible spacing positions per pedal:

- Three for accelerator pedal

- Three for brake pedal

- Three for clutch pedal

Adjusting the INCLINATION of the pedals

- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and

its support (7) in place.

- Turn the plastic head support (7) 180°, then replace and re-tighten the screws so that the metal

head (8) and its support (7) are held firmly in place.

Examples illustrating the accelerator pedal:

Less inclined position More inclined position (default)

Number of possible inclination positions per pedal:

- Two for accelerator pedal

- Two for brake pedal

- Two for clutch pedal

ページが読み込まれています...

Thrustmaster 4469021 ユーザーマニュアル

Thrustmaster 4469021 ユーザーマニュアル

他の言語で

関連論文