Thrustmaster 4469024 ユーザーマニュアル

Europe, Middle East

ENGLISH

FRANÇAIS

DEUTSCH

NEDERLANDS

ITALIANO

ESPAÑOL

PORTUGUÊS

РУССКИЙ

ΕΛΛΗΝΙΚΑ

TÜRKÇE

POLSKI

ﺔﻴﺑﺮﻌﻟا

North America/

Norteamérica

ENGLISH

FRANÇAIS

ESPAÑOL

Latin America/

América Latina

ENGLISH

ESPAÑOL

PORTUGUÊS

Asia Pacic

日本語

繁體中文

1/22

For Xbox One and Windows

User Manual

2/22

TECHNICAL FEATURES

1 Base

2 Wheel

3 2 sequential paddle shifters (up & down)

4 D-pad with push button

5 Xbox Guide button + white indicator light

6 MODE button + red/green indicator light

7 Large threaded hole (for attachment system

and fastening screw)

8 Attachment system

9 Metal fastening screw

3/22

15 Thrustmaster Quick Release

16 Connector for TURBO POWER power

supply

17 Connector for removable USB cable

18 Connector for pedal set

19 Connector for TH8A shifter (shifter sold

separately)

20 TURBO POWER power supply

21 Power supply cable

22 Removable USB cable

PLUGGING THE WHEEL INTO AN ELECTRICAL OUTLET:

PLEASE READ CAREFULLY!

Never plug the TURBO POWER power supply into an electrical outlet with a different

voltage! The TURBO POWER power supply’s voltage is indicated on the label located above the female

connector for the power supply cable.

Never connect a power supply other than the TURBO POWER power supply to the TS-XW

RACER base, even if the connector is compatible! For example, never connect the power adapter for

the T500 RS wheel to the TS-XW RACER base.

4/22

WARNING

Before using this product, please read this manual carefully and save it for later reference.

Warning – Electrical shock

* Keep the product in a dry location and do not expose it to dust or sunlight.

* Do not twist or pull on the connectors and cables.

* Do not spill any liquid on the product or its connectors.

* Do not short-circuit the product.

* Never dismantle the product; do not throw it onto a fire and do not expose it to high temperatures.

* Do not use a power supply cable other than the one provided with your racing wheel.

* Do not use the power supply cable if the cable or its connectors are damaged, split or broken.

* Make sure that the power supply cable is properly plugged into an electrical outlet, and properly

connected to the connector at the rear of the racing wheel’s base.

* Do not open up the racing wheel: there are no user-serviceable parts inside. Any repairs must be

carried out by the manufacturer, its authorized representative or a qualified technician.

* Only use attachment systems/accessories specified by the manufacturer.

* If the racing wheel is operating abnormally (if it is emitting any abnormal sounds, heat or odors), stop

using it immediately, unplug the power supply cable from the electrical outlet and disconnect the other

cables.

* If you will not be using the racing wheel for an extended period of time, unplug its power supply cable

from the electrical outlet.

* The electrical outlet must be located near the equipment and must be easily accessible.

Air vents

Make sure not to block any of the air vents on the racing wheel’s base. For optimal ventilation, make sure

to do the following:

* Position the wheel’s base at least 10 cm away from any wall surfaces.

* Do not place the base in any tight spaces.

* Do not cover the base.

* Do not let any dust build up on the air vents.

For safety reasons, never use the pedal set with bare feet

or while wearing only socks on your feet.

THRUSTMASTER

®

DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF

INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES.

Warning – Injuries due to Force Feedback and repeated movements

Playing with a Force Feedback racing wheel may cause muscle or joint pain. To avoid any problems:

* Avoid lengthy gaming periods.

* Take 10 to 15 minute breaks after each hour of play.

* If you feel any fatigue or pain in your hands, wrists, arms, feet or legs, stop playing and rest for a few

hours before you start playing again.

5/22

Warning – Injuries due to Force Feedback and repeated movements (continued)

* If the symptoms or pain indicated persist when you start playing again, stop playing and consult your

doctor.

* Keep out of children’s reach.

* During gameplay, always leave both hands correctly positioned on the wheel without completely

letting go.

* During gameplay, never place your hands or your fingers under the pedals or anywhere near the

pedal set.

* During calibration and gameplay, never place your hand or your arm through the openings in the

racing wheel.

* Make sure that the racing wheel’s base is properly secured, as per this manual’s instructions.

Product to be handled only by users

16 years of age or older

HEAVY PRODUCT

Be careful not to drop the product on

yourself or on anyone else!

ALWAYS

6/22

COMPATIBILITY WITH THE THRUSTMASTER ECOSYSTEM

Pedal sets

The TS-XW RACER base is compatible:

- On Xbox One and Windows, with the Thrustmaster T3PA and T3PA-PRO pedal sets that connect

directly to the connector for pedal set (18).

- On Windows, with the Thrustmaster DB9 PEDALS T.RJ12 ADAPTER that enables the non-

Thrustmaster pedal sets equipped with a DB9 connector to connect to the connector for pedal set (18).

- On Windows (only), with all the USB pedal sets on the market (in games supporting MULTI-USB and

USB pedal sets).

Wheels

The TS-XW RACER base is compatible, on Xbox One and Windows, with all Thrustmaster detachable

wheels, including:

- Ferrari 599XX EVO 30 Wheel Add-On Alcantara Edition

- Ferrari F1 Wheel Add-On

- Ferrari GTE Wheel Add-On Ferrari 458 Challenge Edition

- TM Leather 28 GT Wheel Add-On

- TM Open Wheel Add-On

- TM Competition Wheel Sparco® P310 Mod

- TM Rally Wheel Add-On Sparco® R383 Mod

- etc.

Shifters

The TS-XW RACER base is compatible:

- On Xbox One, with the Thrustmaster TH8A Shifter Add-On shifter: connect it directly to the connector

for TH8A shifter (19) for the “Sequential (+/-)” and “H-pattern (7+1)” modes.

- On Windows, with the Thrustmaster TH8A Shifter Add-On shifter: connect it directly to the connector

for TH8A shifter (19) for the “Sequential (+/-)”mode.

- On Windows, with the Thrustmaster TH8A Shifter Add-On shifter: connect it to a USB port for the

“Sequential (+/-)”, “H-pattern (7+1)” and ANALOG / HANDBRAKE modes.

- On Windows, with all the USB shifters on the market (in games supporting MULTI-USB and USB

shifters).

HELP FILES AND FAQS (not included in this manual)

Please visit http://support.thrustmaster.com. Click Racing Wheels / TS-XW RACER, and then

select Manual or FAQ.

7/22

INSTALLING THE WHEEL ON ITS BASE

Align the connector positions using the arrows:

Base (1) connector: Arrow pointing upwards

Racing wheel (2) connector: Arrow pointing upwards

Once the connectors are correctly positioned, simply rotate the Thrustmaster Quick Release (15) device’s

ring anticlockwise, while holding the racing wheel (2) in position.

Then, tighten the ring as much as you can: to do so, hold the ring in position and rotate the racing wheel

clockwise.

Once you have installed the wheel, rotate it 180° (when facing the wheel, the Sparco logo should be

upside down) to access the small attachment screw located on the ring of the Thrustmaster Quick

Release (15) device. Use a large Phillips screwdriver to tighten the small attachment screw (do not use

excessive force), turning it clockwise.

When using a Philips screwdriver, ensure NOT to use excessive force

when tightening the small attachment screw!

Stop turning the screw as soon as you feel some resistance.

8/22

ATTACHING THE RACING WHEEL

Attaching the racing wheel’s base to a cockpit

1. Place the racing wheel’s base on the cockpit shelf.

2. Drive two M6 screws (not included) through the cockpit shelf, then feed them into the two small

screw threads located on the underside of the racing wheel.

Important: The length of the two M6 screws must not exceed the thickness of the shelf + 12 mm;

longer screws could cause damage to internal components located in the racing wheel’s base.

3. If required, tighten the standard attachment system by inserting the fastening screw in the large

threaded hole.

Attaching the racing wheel to a table or a desktop

1. Place the racing wheel on a table or any other horizontal, flat and stable surface.

2. Insert the fastening screw (9) in the attachment system (8), then tighten the device by turning the

screw anticlockwise, so that it feeds into the large threaded hole (7) located beneath the racing

wheel, until the wheel is perfectly stable.

ALWAYS NEVER

WARNING:

- Never tighten the screw alone, without the attachment system in place (this could

damage the racing wheel).

9/22

ATTACHMENT /

REMOVAL

DIRECTION

To tighten:

Turn the screw

anticlockwise

To release:

Turn the screw

clockwise

10/22

INSTALLATION ON XBOX ONE

1. Connect the pedal set to the connector (18) located at the back of the racing wheel's base.

2. Connect the TURBO POWER power supply cable (20) to the connector (16) located at the back of

the racing wheel's base.

3. Connect the removable power supply cable (21) to the TURBO POWER power supply (20).

4. Connect the removable power supply cable (21) to a mains outlet with proper voltage

specifications.

5. Connect the removable racing wheel's USB connector (22) to the racing wheel's connector (17) and

to one of the console's USB ports.

6. When you turn on your console, the racing wheel automatically self-calibrates.

You are now ready to race!

The list of Xbox One games compatible with the TS-XW RACER is available here:

http://support.thrustmaster.com (in the Racing Wheels / TS-XW RACER section).

This list is updated regularly.

XBOX ONE MAPPING

11/22

INSTALLATION ON PC

1. Go to http://support.thrustmaster.com, then select Racing Wheels / TS-XW RACER to

download the drivers and the force feedback software for PC.

2. Once the download is complete, launch the installation, and follow the on-screen instructions to

connect the wheel’s USB plug to your computer and complete the installation.

3. Once the installation is complete, click Finish and restart your computer.

4. Select Start / All Programs / Thrustmaster / FFB Racing Wheel / Control Panel to open the Game

Controllers window.

The Game Controllers window displays the racing wheel’s name Thrustmaster TS-XW RACER with

the status OK.

5. Click Properties to configure your wheel in the TS- XW RACER control panel:

• Test Input tab: allows to test and view the action buttons, directional buttons, wheel and pedals

axes, and to adjust the wheel’s rotation angle in your PC games.

• Test Forces tab: allows to test 12 force feedback effects.

• Gain Settings tab: allows to adjust the power of the force feedback effects in your PC games.

You are now ready to play!

General notes:

- On PC, click OK to close the Game Controllers window before launching the game.

- Your wheel’s firmware version is displayed in the upper right-hand corner of the control panel tabs.

PC MAPPING

12/22

UPDATING YOUR RACING WHEEL’S FIRMWARE

The firmware included in your racing wheel’s base can be updated to a more recent version featuring

product enhancements.

To display the firmware version that your racing wheel is currently using and update it if required: on

PC, visit http://support.thrustmaster.com. Click Racing Wheels / TS-XW RACER, then select

Firmware and follow the instructions describing the download and installation procedure.

AUTOMATIC RACING WHEEL CALIBRATION

The wheel automatically self-calibrates when you plug the racing wheel into an electrical outlet and

connect the racing wheel’s USB connector.

During this phase, the racing wheel will rotate quickly towards the left and the right, covering a 1080

degree angle, before stopping at the center.

WARNING:

Never touch the racing wheel during the self-calibration phase!

(This could result in improper calibration and/or personal injuries.)

If your racing wheel does not function correctly, or if it seems to be improperly calibrated:

Power off your PC or your console and completely disconnect the racing wheel. Then reconnect all

cables (including the power supply cable and the pedal set), and restart your PC and your game.

INTERNAL COOLING SYSTEM FOR THE WHEEL’S BASE

The internal cooling system for the wheel’s base

- starts working when the wheel is powered on.

- switches off after a few minutes of inactivity when the internal temperature cools down to a low level.

- switches on again when you use the wheel.

MODE BUTTON AND INDICATOR LIGHT (6)

MODE button for the pedal set

You can electronically swap the accelerator and clutch pedals if you are using a Thrustmaster T3PA or

T3PA-PRO pedal set connected to the connector for pedal set (18).

To do so, simply press the MODE button (6) for 2 seconds.

The racing wheel’s internal memory stores whether the pedals have been swapped around or not.

GAS AND CLUTCH PEDALS

Color of the MODE indicator light (6)

NORMAL

RED

SWAPPED AROUND

GREEN

Other information regarding the MODE button

To learn more about the MODE button and indicator light, please visit

http://support.thrustmaster.com. Click Racing Wheels / TS-XW RACER, and then select Manual or

FAQ.

13/22

TECHNICAL FEATURES

1 Metal support for conical stop

(not installed by default)

2 Conical stop

3 Attachment screw for metal support

4 2.5 mm Allen key (included)

5 Position adjustment nut for conical stop

6 Pedal arm

7 Plastic head support

8 Metal pedal head

14/22

WARNING

Before using this product, be sure to read these instructions carefully and save them for future reference.

For safety reasons, never use the pedal set with bare feet or while wearing

only socks on your feet.

THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF

INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES.

Warning – Pedal set pinching hazard during gaming sessions

* Keep the pedal set out of the reach of children.

* During gaming sessions, never place your fingers or thumbs on or near the sides of the pedals.

* During gaming sessions, never place your fingers or thumbs on or near the rear base of the pedals.

* During gaming sessions, never place your fingers or thumbs on or near the front base of the pedals.

NEVER

15/22

AUTOMATIC CALIBRATION OF PEDALS

IMPORTANT:

- Never connect or disconnect the pedal set from the base of the wheel when the wheel is

connected to the system or PC, or during gaming sessions, to avoid calibration problems.

= Always connect the pedal set to the wheel before connecting the wheel to the system or PC.

- Once the wheel has self-calibrated and the game has started, the pedals automatically calibrate

themselves after being pressed a few times.

- Never press on the pedals when the wheel is self-calibrating or when your game is starting up, to

avoid calibration problems.

- If the pedals are not functioning correctly or appear to be improperly calibrated, power off your

system, completely disconnect your wheel, then reconnect all of the cables (including the power

supply cable and the pedal set cable), power the system back on and restart your game.

ATTACHING THE PEDAL SET TO A COCKPIT

- Attach the pedal set using the small screw threads located on the underside of the pedal set.

- Screw two M6 screws (not included) into the cockpit’s pedal support plate and into the two small

screw threads located on the underside of the pedal set.

Important: The length of the two M6 screws must not exceed the thickness of the cockpit’s pedal

support plate plus an additional 10 mm, to avoid damaging the pedal set’s internal components.

16/22

ADJUSTING THE PEDAL SET

Each of the three pedals includes:

- A metal head (8) with multiple perforations (nine for the accelerator – six for the brake – six for the

clutch).

- A plastic head support (7) (placed between the head and the arm) with four perforations.

- A pedal arm (6) with two perforations.

ATTENTION: To avoid any calibration problems, be sure to always disconnect your wheel’s

USB cable from the system or PC before making any adjustments to your pedal set.

Adjusting the HEIGHT of the accelerator pedal

- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and

its support (7) in place.

- Select your preferred height position, then replace and re-tighten the screws so that the metal

head (8) and its support (7) are held firmly in place.

Low position (default)

High position

17/22

Adjusting the SPACING of the three pedals

- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and

its support (7) in place.

- Select your preferred position (to the left, centered, or to the right), then replace and re-tighten the

screws so that the metal head (8) and its support (7) are held firmly in place.

Examples illustrating the brake pedal:

Left position Centered position (default) Right position

Number of possible spacing positions per pedal:

- Three for accelerator pedal

- Three for brake pedal

- Three for clutch pedal

Adjusting the INCLINATION of the pedals

- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and

its support (7) in place.

- Turn the plastic head support (7) 180°, then replace and re-tighten the screws so that the metal

head (8) and its support (7) are held firmly in place.

Examples illustrating the accelerator pedal:

Less inclined position More inclined position (default)

Number of possible inclination positions per pedal:

- Two for accelerator pedal

- Two for brake pedal

- Two for clutch pedal

18/22

Installing the conical stop (“CONICAL RUBBER BRAKE” mod)

This modification (or “mod”) is not essential, and is not installed by default. This means that the

brake pedal functions perfectly even if the mod is not installed.

This mod lets you experience a different feeling and resistance when braking.

It’s up to you whether or not to install it, depending on your own preferences.

- Screw the conical stop (2) onto its metal support (1).

- Screw the position adjustment nut (5) onto the bottom (onto the conical stop’s screw thread).

- Position the unit at the back of the brake pedal’s arm.

19/22

- Using the included 2.5 mm Allen key (4), attach the unit using the attachment screw (3) and the

small central screw thread located on the underside of the pedal set.

The “CONICAL RUBBER BRAKE” mod is now installed!

Adjusting the brake pedal’s RANGE of travel and STRENGTH of resistance

By slightly unscrewing the nut (5), you can further strengthen the resistance of the brake pedal by

moving the conical stop (2) closer to the back of the pedal’s arm (if necessary, use a 14 mm wrench

or pliers to re-tighten the nut and maintain the selected position). The closer the conical stop is

positioned to the back of the pedal’s arm, the greater the strength of resistance will be.

Note: When the conical stop is very close to the back of the brake pedal’s arm, you may experience

difficulties in reaching the maximum calibration value. Should that be the case:

* Slowly, press very hard on the brake pedal so as to reach the maximum value (if necessary, stand

very briefly on the pedal – just for a second), then release the pressure; or else

* Move the conical stop a bit farther away from the back of the brake pedal’s arm.

ページを読み込んでいます...

Thrustmaster 4469024, TS-XW RACER ユーザーマニュアル

関連論文

その他の書類