Thank you for purchasing this product. Please read this user manual carefully

before use and keep this instruction for future reference. If you have any

problem about this product, please feel free to contact us at

[email protected]m.

Generally wear at 1-2 finger width from wrist join. The sensor of smart watch

Do not use in bath, sauna, hot spring or other hot environments with hot water

and steam, which will lead to product failure.

Owing to the action of water pressure, do not wear it while swimming or diving.

1

Turn On: When in Power off, hold the Multi-Function Button(MFB) for 5s to

turn on the watch.

2

Turn Off: When in Power on, find the On/Off shutdown interface, hold the

MFB for 5s and select “yes” to turn off.

1

Attach the equipped magnetic charger to the metal contact on the back of

the watch, and insert the other end of the charger into USB wall charger or USB

interface of computer.

Charge under the following circumstances:

When the battery is low and power off automatically.

2

Screen displays in charging state.

Note: Do not directly look at the blinking sensor light when charging, which may

cause eye irritation.

1

App Download & Supported System.

You can download and install the App “AGPTEK” by scanning the QR code

1) Click “Mine” in the

App.

2) Click “Connect to tracker”, and select “W06” in the scanned device list to

connect.

At this moment, there are two situations:

iOS system: A pairing request will Appear, so you just click "Confirm" to

connect.

1

There is no reminder on the watch when out of the Bluetooth connection

range. However, Bluetooth will automatically reconnect when the watch reaches

the valid range of the Bluetooth connection.

2

If you close the background application or restart the phone or click on

one

click clean-up

of the phone, you need to enter into

AGPTEK

App again. And

Bluetooth will automatically reconnect within the valid range of Bluetooth

connection.

disconnect for a long time, the data of time can not update. It needs to bind App

Default Once Twice Third

The watch will vibrate to remind you when receiving new messages pushed by

the Apps. These messages will save in the message interface of watch. It can

store up to 3 message. If the watch has received over 3 messages, it will be

replaced the previous messages one by one.

Record your sleep from 22:00 pm of the current day to 8:00 am of the next day.

data detected by the watch will be synchronized and updated to the “Sleep” in

App through manually pulling down the the “Today” interface of App.

monitor your heart rate/blood pressure for about 30s. In addition, you can turn

on Continuous heart rate monitoring in App’s “Device Management”(Mine -

Device Management - select to turn on “Continuous heart rate monitoring”).

After that, the watch will automatically start to continuously monitor your heart

the time for heart rate monitor will be prolonged or no data can be measured.

After the watch had gotten the measuring data, You can view the real-time

dynamic heart rate data or move. If there is a big difference in the measured

data, please take a break to re-measure. The average value obtained after 5

consecutive measurements will be more accurate.

3) This product is a real-time dynamic heart rate measurement, so the heart rate

will be different when talking, eating, drinking, etc. The monitoring value may be

closer to your actual situation when you are peaceful.

4) The data of blood pressure measurement are for reference only. It cannot be

used as a basis for medical related aspects.

Five alarm clocks can be set in App. Delete the alarm clock that you want to in

App via sliding the alarm clock left. After setting, it will be synchronized to the

watch. When the alarm is activated, the watch will vibrate to remind you. Just

hold MFB for 3s to stop alarming.

Click “Shake Snapshot” in App. Control your mobile phone via shaking the

watch to capture the moment.

Turn on Location information of your mobile phone. Select Sport and click Start

watch. Hold it for 3s again to start to detect your status when you doing this sport.

Hold it for 3s once again to exit this sports.

und klicken Sie auf Start, um die Ausführung zu starten.

Sportmodus: Laufen, Wandern, Reiten, Schwimmen, Tischtennis, Basketball,

Badminton, Fußball.

Wählen Sie eine der Sportarten aus, auf die Sie zugreifen möchten, indem Sie

die MFB für 3s in der Uhr halten. Halten Sie die Taste 3 Sekunden lang gedrückt,

um Ihren Status zu erkennen, wenn Sie diesen Sport ausüben. Halten Sie es noch

Merci d'avoir acheté ce produit. Veuillez lire attentivement ce manuel avant

l’utilisation et conserver ces instructions pour la référence ultérieure. Si vous avez

un problème avec ce produit, n'hésitez pas à nous contacter à

[email protected]m.

En général, portez-le à 1-2 doigts du poignet. Le capteur de la montre

environnements quotidiens.

Ne pas l’utiliser dans les bains, les saunas, les sources chaudes ou tout autre

environnement chaud avec de l'eau chaude et de la vapeur, ce qui pourrait

1

Allumer: Lorsque l'appareil est mis hors tension, maintenez le bouton

pour l’éteindre.

Remarque

la fréquence cardiaque, la pression artérielle. Ne regardez pas directement la

lumière clignotante du capteur lors de la détection, ce qui pourrait provoquer

une irritation aux yeux.

1. Fixez le chargeur magnétique équipé au contact métallique situé à l'arrière

de la montre, puis insérez l'autre extrémité du chargeur dans le chargeur USB ou

le port USB de l'ordinateur.

Le chargez dans les circonstances suivantes: