Dell PowerEdge M710HD 仕様

Dell™ PowerEdge™

M905, M805, M605,

and M600 Systems

Information Update

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerEdge, PowerConnect, and OpenManage are

trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

October 2008 Rev. A02

Information Update 3

PowerEdge™ M905 and M805 Blades –

Dell™ OpenManage™ Version Requirements

The PowerEdge M905 and M805 blades require OpenManage systems

management software version 5.4.3 or later.

NOTE: OpenManage version 5.4.3 does not support PowerEdge M600 or M605

blades.

PowerEdge M905 and M805 Blades –

CMC Firmware Requirements

PowerEdge M905 and M805 blades require CMC firmware version 1.2 or

later. If you add these blades to an M1000e enclosure with CMC firmware

older than version 1.2, the new blade will not power on.

NOTE: See the latest Dell Chassis Management Controller User's Guide at

support.dell.com for complete instructions on how to configure and operate

the CMC module.

Updating the CMC Firmware

Downloading the CMC Firmware

Before beginning the firmware update, download the latest firmware version

from the support.dell.com website, and save it to your local system.

The following software components are included with your CMC firmware

package:

• Compiled CMC firmware code and data

• Web-based interface, JPEG, and other user interface data files

• Default configuration files

Use the Firmware Update page to update the CMC firmware to the latest

revision.

NOTE: See the latest Dell Chassis Management Controller User's Guide at

support.dell.com for complete instructions on how to configure and operate

the CMC module.

NOTE: The firmware update, by default, will retain the current CMC settings.

During the update process, you have the option to reset the CMC configuration

settings back to the factory default settings.

4 Information Update

Updating Firmware in a Redundant CMC Configuration

NOTICE: In a redundant CMC configuration, you must update CMC firmware on

both modules. Failure to do so may cause unexpected behavior during a CMC

failover or failback. Use the following procedure for redundant CMC deployments.

1

Locate the secondary or standby CMC by using the RACADM

getsysinfo

command, or by using the

Chassis Summary

page in the Web-based

interface

.

The status indicator will be solid blue on the primary or active

CMC module and off on the standby or secondary CMC.

2

Update the firmware on the standby CMC first. See "Updating the CMC

Firmware Using the Web-based Interface" or "Updating the CMC

Firmware Using RACADM".

3

Verify that the secondary or standby CMC’s firmware is at the requested

level with the

getsysinfo

command or through the Web-based interface.

4

After the standby CMC has rebooted, update the firmware on the active

or primary CMC. Allow 10 minutes for the standby CMC to boot.

See "Updating the CMC Firmware Using the Web-based Interface"

or "Updating the CMC Firmware Using RACADM".

5

Verify that the active or primary CMC firmware is at the requested level

using the

getsysinfo

command or through the Web-based interface.

6

Once both CMCs are updated to the same firmware revision, use the

cmcchangeover

command to reset the CMC in the left slot as primary.

Updating the CMC Firmware Using the Web-based Interface

1

Log in to the Web-based interface. See "Logging in to the CMC Using

the Web-Based Interface" in your M1000e

Configuration Guide

.

2

Click

Chassis

in the system tree.

3

Click the

Update

tab. The

Updatable Components

page appears.

4

On the

Updatable Components

page, click the CMC name.

The

Firmware Update

page appears.

Information Update 5

5

In the

Va lu e

field, type the path on your management station or shared

network where the firmware image file resides, or click

Browse

to navigate

to the file location.

NOTE: The default CMC firmware image name is firmimg.cmc and the filename

should not be changed. Keep different firmware revisions separated as the file

name will always be the same.

6

Click

Update

. A dialog box appears asking you to confirm the action.

7

Click

Yes

to continue. The firmware transfer process will begin and the

status will display the message "Firmware Update in Progress". Once the

CMC update is complete, the CMC will be reset. Once the reset is

complete, you will need to refresh the

User Interface

page to log in again.

Updating the CMC Firmware Using RACADM

1

Open a CMC command line console and log in.

2

Ty p e :

racadm fwupdate -g -u -a <TFTP server IP address>

-d <filepath> -m <cmc-active|cmc-standby>

See the latest Dell Chassis Management Controller User's Guide at

support.dell.com for complete instructions on how to configure and

operate the CMC module.

PowerEdge M905 and M805 Blades –

Memory Sparing Requirements

The following information updates the memory sparing subsections in your

Hardware Owner’s Manual and these blades’ system information labels.

PowerEdge M905

Memory sparing is supported if 24 identical memory modules (DIMMs)

are installed.

PowerEdge M805

Memory sparing is supported if 16 identical memory modules are installed.

6 Information Update

New Mezzanine Cards

Your blade now supports the following additional mezzanine cards:

• Broadcom 57710 10Gb Ethernet card

• Emulex LPe1205-M FC8 card

• QLogic QME2572 FC8 card

NOTE: CMC firmware version 1.3 is required to support FC8 mezzanine cards

and I/O modules.

For information on installing a mezzanine card, see "Installing System

Components" in your Hardware Owner’s Manual. For detailed information

on configuring a particular card, see the card’s documentation on

support.dell.com.

New I/O Modules

Your system now supports the following I/O modules:

•

Dell PowerConnect™ M8024 10Gb Ethernet switch module

• Mellanox M2401G Infiniband switch module

•

Brocade M5424 FC8 module

NOTE: CMC firmware version 1.3 is required to support FC8 mezzanine cards

and I/O modules.

These modules are hot-pluggable, and may be installed in Fabric B or

Fabric C. (The M8024 Ethernet switch module may also be installed in

Fabric A, but will only operate at 1 Gb in this Fabric.) For general information

on installing I/O modules, see "I/O Modules" in your Hardware Owner’s

Manual.

Information Update 7

PowerConnect M8024 10 Gb Ethernet Switch I/O Module

The PowerConnect M8024 switch module incorporates two option bays

that support the following modules:

• A 10 Gb Ethernet module with four optical SFP+ connectors

• A 10 Gb Ethernet module with three copper CX4 uplinks

The modules can be used in any combination and are sold separately.

You can initially configure the switch using either of two methods:

• Connect an external management system to the switch using an optional

USB type-A form factor serial cable, and configure the switch using a

terminal application.

• Use the iKVM CMC console ("17th blade") and the

connect switch-

n

CMC CLI command. For more information, see the CMC user’s guide.

Once an IP address is assigned to the management VLAN or interface and

the switch is connected to a management network, both Telnet and http

are available through the network.

8 Information Update

Figure 1-1. PowerConnect M8024 Switch Module

1 optional module with four SFP+ ports 2 optional module

with three CX4 ports

3 serial connector for optional USB type-A

form-factor cable

4 power indicator

5 status/identification indicator

4

1

5

2

3

Information Update 9

Mellanox M2401G Infiniband Switch I/O Module

The Mellanox M2401G Infiniband switch I/O module includes 24 4x DDR

Infiniband ports. Eight ports are external uplink ports, while 16 internal ports

provide connectivity to the blades in the enclosure.

Figure 1-2. Mellanox M2401G Infiniband Switch Module

1 Infiniband ports (8) 2 port link status indicators (8)

3 port activity indicators (8) 4 module diagnostic power indicator

5 module status indicator

4

1

5

2

3

10 Information Update

Brocade M5424 FC8 I/O Module

The Brocade M5424 I/O module includes eight external autosensing Fibre

Channel ports (four ports are enabled in the standard configuration and four

additional ports may be enabled as an optional upgrade), 16 internal ports,

and one serial port with an RJ-45 connector. The external Fibre Channel ports

operate at 8 Gb/sec, 4 Gb/sec, or 2 Gb/sec.

NOTE: CMC firmware version 1.3 is required to support FC8 mezzanine cards and

I/O modules.

NOTE: This Fibre Channel switch module includes Short Wave Small Form Factor

Pluggable (SFP) optical transceivers. To ensure proper functionality, use only SFPs

provided with this module.

Table 1-1. Mellanox M2401G Infiniband Switch Indicators

Indicator Pattern Description

Link indicator Green, on Physical link established

Green, off No physical link present

Activity

indicator

Amber, on Valid logical link to Infiniband network

established

Amber, blinking Data transfer is occurring

Amber, off No logical link to Infiniband network

Information Update 11

Figure 1-3. Brocade M5424 FC8 I/O Module

1 Fibre Channel port (8) 2 Fibre Channel port status

indicator (8)

3 Fibre Channel port speed

indicator (8)

4 serial port (RJ-45 connector)

5 module status indicator 6 power indicator

7 status/identification indicator

2

4

3

5

6

7

1

12 Information Update

Indicator Type Pattern Description

Fibre Channel

port status

indicator

Off No signal carrier

Amber on Signal present but not online

Green on Online, but no activity

Green

blinking slowly

Online but segmented

Green

blinking quickly

Internal loopback

Green flickering I/O activity on port

Amber

blinking slowly

Port disabled

Amber

blinking rapidly

Error or fault with port

Fibre Channel

port speed

indicator

Off 2 Gb link established

Green on 4 Gb link established

Amber on 8 Gb link established

Module status

indicator

Off Module is off or enclosure power is off.

Green on All ports are ready for use.

Amber on Module is booting being reset, or ports are offline.

Green/amber

blinking

Diagnostic message is in error log, or

environmental range is exceeded.

Module power

indicator

Off Power to the module is off.

Green Module has power.

Status/

identification

indicator

Blue on Primary module in a stack, if applicable

Blue off Secondary module in a stack

Amber flashing Fault condition in module

Dell

™

PowerEdge

™

M905

、

M805

、

M605

和

M600

系统

信息更新

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式复制这些材料。

本文中使用的商标：

Dell

、

DELL

徽标、

PowerEdge

、

PowerConnect

和

OpenManage

是

Dell Inc.

的商标。

本说明文件中述及的其它商标和产品名称是指拥有相应商标和产品名称的公司或其制造的

产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。

2008

年

10

月

Rev. A02

信息更新 15

PowerEdge™ M905

和

M805

刀片

–

Dell™ OpenManage™

版要求

PowerEdge M905

和

M805

刀片要求使用

5.4.3

版或更高版本的

OpenManage

系统管理软件。

注：

OpenManage 5.4.3

版不支持

PowerEdge M600

或

M605

刀片。

PowerEdge M905

和

M805

刀片

— CMC

固件

要求

PowerEdge M905

和

M805

刀片要求

CMC

固件为

1.2

版或更高版本。如果

您将这些刀片装在

CMC

固件低于版本

1.2

的

M1000e

机壳上，新刀片将

无法通电。

注：请参阅

support.dell.com

上的最新《

Dell

机箱管理控制器用户指南》以了

解有关如何配置和操作

CMC

模块的完整说明。

更新

CMC

固件

下载

CMC

固件

在开始固件更新之前，从

support.dell.com Web

站点下载最新的固件

版本，并保存到您的本地系统。

CMC

固件包包含以下软件组件：

•

编译的

CMC

固件代码和数据

•

基于

Web

的界面、

JPEG

和其它用户界面数据文件

•

默认配置文件

使用

Firmware Update

（固件更新）页面，将

CMC

固件更新为最新

版本。

注：请参阅位于

support.dell.com

的最新《

Dell

机箱管理控制器用户指南》

以了解有关如何配置和操作

CMC

模块的完整说明。

注：默认情况下，固件更新会保留当前的

CMC

设置。更新过程中，可以选

择将

CMC

配置设置重设为出厂默认设置。

16 信息更新

更新冗余

CMC

配置中的固件

注意：在冗余

CMC

配置中，必须更新两个模块的

CMC

固件。否则可能会导

致在

CMC

故障转移或故障回复期间出现意外行为。使用以下步骤进行冗余

CMC

部署。

1

使用

RACADM

getsysinfo

命令或使用

Chassis Summary

（机箱摘要）

页面（位于基于

Web

的界面中）查找次级或备用

CMC

。可以看到主

CMC

或活动

CMC

模块的状态指示灯呈纯蓝色，备用

CMC

或次级

CMC

的指示灯不亮。

2

首先更新备用

CMC

上的固件。请参阅“使用基于

Web

的界面更新

CMC

固件”或“使用

RACADM

更新

CMC

固件”。

3

使用

getsysinfo

命令或通过基于

Web

的界面验证次级

CMC

或备用

CMC

的固件已达到所要求的水准。

4

重新引导备用

CMC

后，更新活动或主

CMC

上的固件。请留出

10

分

钟引导备用

CMC

。

请参阅“使用基于

Web

的界面更新

CMC

固件”或“使用

RACADM

更新

CMC

固件”。

5

使用

getsysinfo

命令或通过基于

Web

的界面验证活动

CMC

或主

CMC

的固件已达到所要求的水准。

6

一旦两个

CMC

都更新为相同的固件修订版本，使用

cmcchangeover

命

令将左插槽中的

CMC

重设为主

CMC

。

使用基于

Web

的界面更新

CMC

固件

1

登录到基于

Web

的界面。请参阅

M1000e

《

配置指南》中的“使用基

于

Web

的界面登录到

CMC

”

。

2

单击系统树中的

Chassis

（机箱）。

3

单击

Update

（更新）选项卡。此时将会显示

Updatable Components

（可更新组件）页。

4

在

Updatable Components

（可更新组件）页面上，单击

CMC name

（

CMC

名称）。显示

Firmware Update

（固件更新）页面。

5

在

Va lu e

（值）字段中键入固件映像文件驻留的管理站或共享网络的

路径，或单击

Browse

（浏览）导航到文件位置。

注：默认

CMC

固件映像名称为

firmimg.cmc

，且文件名不可更改。由于文件

名始终相同，所以必须分开保存不同的固件版本。

信息更新 17

6

单击

Update

（更新）。显示一个对话框，要求您确认刚才的操作。

7

单击

Yes

（是）继续。固件传输过程将开始，显示的状态消息为

“

Firmware Update in Progress

”（正在更新固件）。

CMC

更新一旦

完成，将重设

CMC

。重设完成后，将需要刷新

User Interface

（用户

界面）页面以再次登录。

使用

RACADM

更新

CMC

固件

1

打开

CMC

命令行控制台并登录。

2

键入：

racadm fwupdate -g -u -a <TFTP

服务器

IP

地址

> -d

<

文件路径

> -m <cmc-active|cmc-standby>

请参阅

support.dell.com

上的最新《

Dell

机箱管理控制器用户指南》以了

解有关如何配置和操作

CMC

模块的完整说明。

PowerEdge M905

和

M805

刀片

—

内存备用要求

以下信息是对《硬件用户手册》中的内存备用小节以及这些刀片的系统信

息标签的更新。

PowerEdge M905

如果已安装了

24

个完全相同的内存模块

(DIMM)

，则可支持内存备用。

PowerEdge M805

如果已安装了

16

个完全相同的内存模块，则可支持内存备用。

新夹层卡

您的刀片目前支持以下附加的夹层卡：

•

Broadcom 57710 10Gb

以太网卡

•

Emulex LPe1205-M FC8

卡

•

QLogic QME2572 FC8

卡

注：需要

CMC

固件版本

1.3

才能支持

FC8

夹层卡和

I/O

模块。

有关夹层卡的信息，请参阅《硬件用户手册》中的“安装系统组件”。

有关配置特定卡的详情，请参阅

support.dell.com

上该卡的说明文件。

18 信息更新

新

I/O

模块

您的系统现在支持以下

I/O

模块：

•

Dell PowerConnect™ M8024 10Gb

以太网交换机模块

•

Mellanox M2401G Infiniband

交换机模块

•

Brocade M5424 FC8

模块

注：需要

CMC

固件版本

1.3

才能支持

FC8

夹层卡和

I/O

模块。

这些模块可以热插拔，并且可安装到结构

B

或结构

C

中。（

M8024

以太

网交换机模块还可以安装到结构

A

中，但在此结构中将只能以

1 Gb

速度

运转。）有关安装

I/O

模块的一般信息，请参阅《硬件用户手册》中的

“

I/O

模块”。

PowerConnect M8024 10 Gb

以太网交换机

I/O

模块

PowerConnect M8024

交换机模块整合了两个可选的托架支持以下模块：

•

带有四个光学

SFP+

连接器的

10 Gb

以太网模块

• 带有三个铜缆

CX4

上行链路的

10 Gb

以太网模块

这些模块可任意组合使用，并且单独销售。

可以使用以下两种方法中的任一种初始配置交换机：

•

使用可选的

USB A

类外形尺寸串行电缆将外部管理系统连接至交

换机，然后使用终端应用程序配置该交换机。

•

使用

iKVM CMC

控制台（“第

17

个刀片”）和

connect switch-

n

CMC CLI

命令。有关详情，请参阅

CMC user's guide

（

CMC

用户

指南）。

一旦将

IP

地址分配给管理

VLAN

或接口并且交换机连接至管理网络后，

Telnet

和

http

均通过该网络可用。

信息更新 19

图

1-1. PowerConnect M8024

交换机模块

1

带有四个

SFP+

端口的可选模块

2

带有三个

CX4

端口的可选模块

3

用于可选的

USB A

类外型尺寸电

缆的串行连接器

4

电源指示灯

5

状态

/

标识指示灯

4

1

5

2

3

20 信息更新

Mellanox M2401G Infiniband

交换机

I/O

模块

Mellanox M2401G Infiniband

交换机

I/O

模块包括

24

个

4x DDR

Infiniband

端口。其中

8

个是外部上行链路端口，另外

16

个内部端口可连

接到硬盘柜中的刀片。

图

1-2. Mellanox M2401G Infiniband

交换机模块

1

Infiniband

端口

(8)

2

端口链接状态指示灯

(8)

3

端口活动指示灯

(8)

4

模块诊断电源指示灯

5

模块状态指示灯

4

1

5

2

3

ページが読み込まれています...

Dell PowerEdge M710HD 仕様

Dell PowerEdge M710HD 仕様

他の言語で

関連論文