OWNER'S MANUAL
Color Video Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
L2304 Series
L2304-DN
L2304-DP
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A ground-
ing type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for replacement of the obso-
lete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-
over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Accessories
Installation sticker
M3 Tapping screws
(2 EA)
(Pan Lock Screw)
Specication
Item L2304-DP L2304-DN
Signal System PAL NTSC
Total/Effective Pixels
610 000 Pixels
/ 570 000 Pixels
520 000 Pixels
/ 480 000 Pixels
Image Device 6 mm CCD
Signal Process Sony Effio-E
Lens Fixed Lens
IRIS Control ELC
Sync. System Internal
Scanning Frequency (H/V) 15.625 kHz / 50 Hz 15.734 kHz / 59.94 Hz
Horizontal Resolution 650 TV Lines
S/N Ratio 50 dB
Minimum Illumination 0.1 lx F1.2, 30 IRE
Video Output Signal 1 Vp-p Composite (75 Ω)
Day & Night DIGITAL AUTO/COLOR/ B/W
Item L2304-DP L2304-DN
BACKLIGHT OFF / BLC / HLC
DNR 2D-DNR
Electronic Shutter Speed 1/50 to 1/10 000 1/60 to 1/10 000
White Balance
ATW / PUSH /USER1 / USER2
/ ANTI CR / MANUAL/PUSH LOCK
Power Source DC 12 V
Power Consumption 100 mA
Operation Temp. -10 ºC to 50 ºC
Storage Temp. -20 ºC to 60 ºC
Operation Humidity 0 % RH to 80 % RH
Storage Humidity 0 % RH to 85 % RH
Weight 165 g
Dimension (Ø x H) 88 mm x 67.5 mm
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equip-
ment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful inter-
ference in which case the user will be required to correct the interference at his
own expense.
A suitable conduit entries, knock-outs or glands shall be provided in the •
cable entries of this product in the end user.
Caution: Danger of explosion if battery is incorrectly replaced. Replaced •
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Holes in metal, through which insulated wires pass, shall have smooth well •
rounded surfaces or shall be provided with brushings.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
Warning: Do not install this equipment in a confined space such as a bookcase
or similar unit.
Warning: Wiring methods shall be in accordance with the National Electric
Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.
Warning: To reduce a risk of fire or electric shock, do not expose this product to
rain or moisture.
Caution: This installation should be made by a qualified service person and
should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to
qualified personnel only.
Caution: The apparatus shall not be exposed to water (dripping or splashing)
and no objects filled with liquids, such as vases, shall be placed on the appara-
tus.
To disconnect power from mains, pull out the mains cord plug. When install-
ing the product, ensure that the plug is easily accessible.
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of Directive
2004/108/EC, 2006/95/EC, and 2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-(0)36-547-8888)
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is cov-
ered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed
by the government or the local authorities.
3. The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of
your old appliance, please contact your city office,
waste disposal service or the shop where you pur-
chased the product.
EEE Compliance with Directive. (for Turkey only)
a
Using the installation sticker as a guide, make a hole through
the ceiling.
< >
<ﻲﺳﺭﺎﻓ> .ﺪﻴﻨﻛ ﺩﺎﺠﻳﺍ ﻒﻘﺳ ﺭﺩ ﺥﺍﺭﻮﺳ ﮏﻳ ﻭ ﻩﺩﻮﻤﻧ ﻩﺩﺎﻔﺘﺳﺍ ﺎﻤﻨﻫﺍﺭ ﻥﺍﻮﻨﻌﺑ ﺐﺼﻧ ﺐﺴﭼﺮﺑ ﺯﺍ
<ﻲﺑﺮﻋ>
.ﻒﻘﺴﻟﺍ ﻲﻓ ﺔﺤﺘﻓ ﻞﻤﻌﺑ ﻢﻗ ،ﻞﻴﻟﺪﻛ ﺐﻴﻛﺮﺘﻟﺍ ﻖﺼﻠﻣ ﻡﺍﺪﺨﺘﺳﺎﺑ
b
Disassemble the Dome Cover from the main body by
turning it counterclockwise and then detach the Lens Cover.
< >
<ﻲﺳﺭﺎﻓ> .ﺕﺎﺳﺪﻌﻟﺍ ﺀﺎﻄﻏ ﻚﻔﺑ ﻢﻗ ﻢﺛ ﺔﻋﺎﺴﻟﺍ ﺏﺭﺎﻘﻋ ﻩﺎﺠﺗﺍ ﺲﻜﻋ ﻲﻓ ﺔﻔﻟ ﻖﻳﺮﻃ ﻦﻋ ﻲﺴﻴﺋﺮﻟﺍ ﻞﻜﻴﻬﻟﺍ ﻦﻣ ﻱﻮﻠﻌﻟﺍ ﺀﺎﻄﻐﻟﺍ ﻚﻔﺑ ﻢﻗ
<ﻲﺑﺮﻋ>
.ﺪﻠﺟ ﺰﻨﻟ ﻥﺩﺮﻛ ﺍﺪﺟ ﺲﭙﺳ ﻭ ﺖﻋﺎﺳ ﻪﺑﺮﻘﻋ ﺖﻛﺮﺣ ﻒﻟﺎﺨﻣ ﺖﻬﺟ ﺭﺩ ﻥﺁ ﻒﻄﻋ ﻂﺳﻮﺗ ﯽﻠﺻﺍ ﻪﻧﺪﺑ ﺯﺍ ﺪﺒﻨﮔ ﺪﻠﺟ ﻦﺘﺨﻳﺭ ﻢﻫ
c
Connect the cables to the cable jacks of the camera body.
< >
<ﻲﺳﺭﺎﻓ> .ﺪﻴﻨﻛ ﻞﺼﺘﻣ ﻦﻴﺑﺭﻭﺩ ﻪﻧﺪﺑ یﻭﺭ ﺮﺑ ﺎﻬﻧﺁ ﻩﺪﻧﺭﺍﺩ ﻪﮕﻧ یﺎﻫ ﮏﺟ ﻪﺑ ﺍﺭ ﺎﻫ ﻢﻴﺳ
<ﻲﺑﺮﻋ>
.ﺍﺮﻴﻣﺎﻜﻟﺍ ﻢﺴﺟ ﻲﻓ ﺕﻼﺑﺎﻜﻟﺍ ﺲﺑﺎﻘﻤﺑ ﺕﻼﺑﺎﻜﻟﺍ ﻞﺻﻭ
d
Install the camera by using the M3 Tapping screws to fix it on
the ceiling.
< >
<ﻲﺳﺭﺎﻓ> .ﻒﻘﺴﻟﺍ ﻲﻓ ﺎﻬﺘﻴﺒﺜﺘﻟ M3 ﻚﻔﻣ ﻡﺍﺪﺨﺘﺳﺎﺑ ﺍﺮﻴﻣﺎﻜﻟﺍ ﺖﻴﺒﺜﺘﺑ ﻢﻗ
<ﻲﺑﺮﻋ>
.ﺪﻨﻨﻛ ﻞﺣ ﻒﻘﺳ ﺭﺩ ﺍﺭ ﻥﺁ ﻪﺑ M3 یﺭﺍﺩﺮﺑ ﻩﺮﻬﺑ یﺎﻫ ﭻﻴﭘ ﺯﺍ ﻩﺩﺎﻔﺘﺳﺍ ﺎﺑ ﻦﻴﺑﺭﻭﺩ ﺐﺼﻧ
e
Loosen the Tilting Lock Screw. Adjust the Tilt (Up/Down)
position and then tighten Tilting Lock Screw.
< >
<ﻲﺳﺭﺎﻓ> .ﺔﻟﺎﻣﻹﺍ ﻞﻔﻗ ﺭﺎﻤﺴﻣ ﻂﺑﺭ ﻢﻜﺣﺃ ﻢﺛ (ﻞﻔﺳﻷ / ﻰﻠﻋﻷ) ﺔﻟﺎﻣﻹﺍ ﻮﺘﺴﻣ ﻂﺒﺿﺍ ﺔﻟﺎﻣﻹﺍ ﻞﻔﻗ ﺭﺎﻤﺴﻣ ﻚﻓ
<ﻲﺑﺮﻋ>
.ﭻﻴﭘ ﻞﻔﻗ ﺞﻛ ﺖﻔﺳ ﻥﺁ ﺯﺍ ﺲﭘ ﻭ ﺖﻴﻌﻗﻮﻣ (ﻦﻴﻳﺎﭘ / ﻻﺎﺑ) ﺐﻴﺷ ﻢﻴﻈﻨﺗ .ﻞﻔﻗ ﭻﻴﭘ ﺞﻛ ﻞﺷ
f
Attach the Lens Cover and then assemble the Dome Cover to
the main body by turning it clockwise.
< >
<ﻲﺳﺭﺎﻓ> .ﺔﻋﺎﺴﻟﺍ ﺏﺭﺎﻘﻋ ﺔﻛﺮﺣ ﻩﺎﺠﺗﺍ ﻲﻓ ﻪﻔﻟ ﻖﻳﺮﻃ ﻦﻋ ﻲﺴﻴﺋﺮﻟﺍ ﻞﻜﻴﻬﻟﺎﺑ ﻱﻮﻠﻌﻟﺍ ﺀﺎﻄﻐﻟﺍ ﺐﻴﻛﺮﺗ ﺓﺩﺎﻋﺈﺑ ﻢﻗ ﻢﺛ ﺔﺳﺪﻌﻟﺍ ﺀﺎﻄﻏ ﻕﺎﻓﺭﺈﺑ ﻢﻗ
<ﻲﺑﺮﻋ>
.ﺖﻋﺎﺳ یﺎﻫ ﻪﺑﺮﻘﻋ ﺖﻬﺟ ﻥﺁ ﻞﻳﺪﺒﺗ ﻂﺳﻮﺗ ﯽﻠﺻﺍ ﻪﻧﺪﺑ ﻪﺑ ﺪﺒﻨﮔ ﺪﻠﺟ یﺭﻭﺁ ﻊﻤﺟ ﺲﭙﺳ ﻭ ﺪﻠﺟ ﺰﻨﻟ ﻪﻤﻴﻤﺿ
Installation Guide
/