Samsung HW-A550 ユーザーマニュアル

HW-A550

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - ii

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - iii

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

CAUTION : Danger of explosion if the battery

is replaced incorrectly. Replace only with the

same or equivalent type.

ABOUT THIS MANUAL

The user manual has two parts: simple paper

USER MANUAL and a detailed FULL MANUAL you

can download.

USER MANUAL

See this manual for safety instructions,

product installation, components,

connections, and product specications.

FULL MANUAL

You can access the FULL MANUAL on

Samsung’s on-line customer support centre by

scanning the QR code. To see the manual on

your PC or mobile device, download the

manual in document format from Samsung’s

website. (http://www.samsung.com/support)

Design and specications are subject to change

without prior notice.

ENG - iv

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 2

02 Product Overview 3

Front Panel / Top Panel of the Soundbar ------------------------- 3

Bottom Panel of the Soundbar ------------------------- 4

03 Connecting the Soundbar 5

Connecting Electrical Power

-------------------------

5

Connecting the Soundbar to the Subwoofer

-------------------------

6

– Automatic connection between the Subwoofer and the Soundbar

-------------------------

6

– Manually connecting the Subwoofer if automatic connection fails

-------------------------

7

Connecting an SWA-9100S (Sold Separately) to your Soundbar

-------------------------

9

04 Connecting to your TV 11

Method 1. Connecting with a Cable

-------------------------

11

– Connecting a TV using an HDMI Cable

-------------------------

11

– Connecting using an Optical Cable

-------------------------

13

Method 2. Connecting Wirelessly

-------------------------

14

– Connecting a TV via Bluetooth

-------------------------

14

05 Connecting an External Device 16

Connecting using an HDMI Cable

-------------------------

16

Connecting using an Optical Cable

-------------------------

17

06 Connecting a USB Storage Device 18

ENG - v

07 Connecting a Mobile Device 19

Connecting via Bluetooth

-------------------------

19

08 Using the Remote Control 23

How to Use the Remote Control

-------------------------

23

Adjusting the Soundbar volume with a TV remote control ------------------------- 26

Using the Hidden Buttons (Buttons with more than one function)

-------------------------

27

Output specications for the different sound effect modes

-------------------------

27

09 Installing the Wall Mount 28

Installation Precautions

-------------------------

28

Wallmount Components

-------------------------

28

10 Software Update 30

How to check the Firmware version

-------------------------

30

Update Procedure

-------------------------

31

If UPDATE is not displayed

-------------------------

31

11 Troubleshooting 32

12 Licence 34

13 Open Source Licence Notice 35

14 Important Notes About Service 35

15 SpecicationsandGuide 36

Specications

-------------------------

36

ENG - 2

01 CHECKING THE COMPONENTS

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Soundbar Main Unit Subwoofer Remote Control / Batteries

x 2

Power Cord

(Subwoofer, Soundbar)

AC/DC Adapter

(Soundbar)

HDMI Cable

x 2

(M4 x L10)

x 2

Wall Mount Guide Holder-Screw Screw Bracket-Wall Mount

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Bottom of the Soundbar Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

• Depending on the region, the appearance of the AC plug may differ from the plug displayed above,

or it may be supplied integrated with the AC/DC adapter.

• The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the back cover in the direction of the arrow

until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide

the back cover back into position.

ENG - 3

02 PRODUCT OVERVIEW

Front Panel / Top Panel of the Soundbar

Position the product so that

the SAMSUNG logo is

located on the top.

Top Panel

󰟶

󰟳

󰟴 󰟵

󰟳

Display

Displays the product’s status and current mode.

󰟴

(Power) Button

Turns the power on and off.

• Auto Power Down Function

The unit turns off automatically in the following situations:

– In D.IN / HDMI / BT / USB Mode : If there is no audio signal for 20 minutes.

󰟵

(Volume) Button

Adjusts the volume.

• When adjusted, the volume level appears on the Soundbar’s front display.

󰟶

(Source) Button

Selects the source input mode.

Input mode Display

Optical Digital input D.IN

ARC (HDMI OUT) input D.IN  TV ARC (Auto conversion)

HDMI input HDMI

BLUETOOTH mode BT

USB mode USB

• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and hold the

(Source) button for more than 5 seconds.

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio

Setup menu of your TV. Refer to the owner’s manual supplied with your TV.

ENG - 4

Bottom Panel of the Soundbar

DC 24V

HDMI

USB (5V 0.5A)

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(ARC)

DC 24V

HDMI OUT

(TV-ARC)

AUX IN

HDMI IN

USB (5V 0.5A)

DIGITAL AUDIO IN

(OPTICAL)

HDMI

HDMI TO TV

(ARC)

󰟵

󰟶

󰟷

󰟳

󰟴

󰟳

DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device.

󰟴

USB (5V 0.5A)

Connect a USB device here to play music les stored on the USB device through the Soundbar.

󰟵

HDMI

Inputs digital video and audio signals simultaneously using an HDMI cable.

Connect to the HDMI output of an external device.

󰟶

HDMI TO TV (ARC)

Connect to the HDMI (ARC) jack on a TV.

󰟷

DC 24V (Power Supply In)

Connect the AC/DC power adapter.

• When disconnecting the power cable of the AC/DC power adapter from a wall outlet, pull the plug.

Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between

components are complete.

ENG - 5

03 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components to connect the Subwoofer and Soundbar to an electrical outlet in the following

order:

1. Connect the power cord to the Subwoofer.

2. Connect the power output cable to the power adapter, and then to the Soundbar.

3. Connect the power cord to a wall socket.

See the illustrations below.

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Bottom of the Soundbar Main Unit)

POWER

Rear of Subwoofer

Power Cord

Connecting

Electrical Power

Bottom of the

Soundbar Main Unit

AC/DC Adapter

Connecting

Electrical Power

DC 24V

USB (5V 0.5A)

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

HDMI

HDMI TO TV

(ARC)

Power Cord

• Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so

that it is hanging with the AC cord input facing upwards, water or other foreign substances could

enter the Adapter and cause the Adapter to malfunction.

ENG - 6

Connecting the Soundbar to the Subwoofer

When the subwoofer is connected, you can enjoy rich bass sound.

Automatic connection between the Subwoofer and the Soundbar

When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the

subwoofer is automatically connected to the Soundbar.

• When auto pairing is complete, the blue indicator at the rear of the subwoofer turn on.

LED Indicator Lights on the Rear of Subwoofer

LED Status Description Resolution

Blue

On

Successfully connected

(normal operation)

-

Blinking Recovering the connection

Check if the power cable attached to the

main Soundbar unit is connected properly

or wait about 5 minutes. If blinking persists,

try manually connecting the subwoofer.

See page 7.

Red On

Standby (with the Soundbar

main unit turned off)

Check if the power cable attached to the

main Soundbar unit is connected properly.

Connection failed

Connect again. See the instructions for

manual connection on page 7.

Red and

blue

Blinking Malfunction

See the contact information for the

Samsung Service Centre in this manual.

ENG - 7

Manually connecting the Subwoofer if automatic connection fails

Before performing the manual connection procedure below:

• Check whether the power cables for the Soundbar and subwoofer are connected properly.

• Make sure that the Soundbar is turned on.

1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.

• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.

5 Sec

Rear of Subwoofer

2. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

ID SET

SOUND

MODE

PAIR

5 Sec

SAMSUNG logo is on the top

3. Check if the LINK LED is solid blue (connection complete).

Blue is On

The LINK LED indicator stops blinking and

glows a solid blue when a connection is

established between the Soundbar and the

Wireless Subwoofer.

ENG - 8

NOTES

• Do not connect the power cord of this product or your TV to a wall outlet until all connections

between components are complete.

• Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the

STANDBY LED on the rear of the sub-woofer will turn red after blinking blue several times.

• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar,

interference may cause some sound interruption.

• The maximum transmission distance of the main unit’s wireless signal is about 10 meters, but may

vary depending on your operating environment. If a steel-concrete or metallic wall is between the

main unit and the wireless subwoofer, the system may not operate at all because the wireless

signal cannot penetrate metal.

PRECAUTIONS

• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water

and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and the

Wireless Receiver Module (sold separately) is clear of any obstructions.

ENG - 9

Connecting an SWA-9100S (Sold Separately) to your Soundbar

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit

(SWA-9100S, sold separately) to your Soundbar.

1. Connect the Wireless Receiver Module to 2 Surround Speakers.

– When connecting the speaker cable, connect the core wire to the speaker.

SURROUND-RIGHT

– The speaker cables are colour coded.

SURROUND-LEFT

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

SURROUND-RIGHT

SURROUND-LEFT SURROUND-RIGHT

2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.

• The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not

blink, press the ID SET button on the back of the Wireless Receiver Module with a pen tip for

5~6 seconds until the LINK LED indicator blinks (in Blue). For more about the LED, please refer

to the SWA-9100S user manual.

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

STANDBY

LINK

STANDBY

LINK

Blue blinking

5 Sec

ENG - 10

3. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

ID SET

SOUND

MODE

PAIR

5 Sec

SAMSUNG logo is on the top

CAUTION

• If your Soundbar was playing music when it connects to the SWA-9100S, you may hear some

stuttering from the woofer as the connection nalises.

4. Check if the LINK LED is solid blue (connection complete).

STANDBY

LINK

STANDBY

LINK

Blue is On

The LINK LED indicator stops blinking and

glows a solid blue when a connection is

established between the Soundbar and the

Wireless Receiver Module.

5. If the SWA-9100S is not connected, repeat the procedure from Step 2.

ENG - 11

04 CONNECTING TO YOUR TV

Hear TV sound from your Soundbar through wired or wireless connections.

• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using

the TV’s remote control.

– This feature is supported by 2017 and later Samsung Smart TVs that support Bluetooth when

you connect the Soundbar to the TV using an optical cable.

– This function also allows you to use the TV menu to adjust the sound eld and various settings

as well as the volume and mute.

Method 1. Connecting with a Cable

Connecting a TV using an HDMI Cable

CAUTION

• When both the HDMI cable and optical cable are connected, the HDMI signal is received rst.

• To connect the HDMI cable between the TV and Soundbar, be sure to connect the terminals

marked ARC. Otherwise, the TV sound may not be output.

• The recommended cable is High Speed HDMI Cable with Ethernet.

HDMI TO TV

(ARC)

HDMI IN

(ARC)

Connect to the HDMI IN

(ARC) port of your TV.

Bottom of the Soundbar

Connect to the HDMI TO TV (ARC) port

of the Soundbar main unit.

Top of the Soundbar

HDMI Cable

󰟳

󰟴

TV ARC

1. With the Soundbar and TV turned on, connect the HDMI cable as shown in the gure.

2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV

sound.

ENG - 12

• If TV sound is inaudible, press the (Source) button on the remote control or on the top of

the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence,

and TV sound is played.

• If “TV ARC” does not appear in the display window of the Soundbar main unit, conrm that the

HDMI cable is connected to the correct port.

• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.

NOTES

• HDMI is an interface that enables the digital transmission of video and audio data with just a single

connector.

• If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.

• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one

whose diameter is less than 14 mm.

• This function is not available if the HDMI cable does not support ARC

• When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on

your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the

setting on the TV is changed, you will experience better sound quality. (The TV menu may use

different words for Dolby Digital and PCM depending on the TV manufacturer.).

ENG - 13

Connecting using an Optical Cable

Pre-connection Checklist

• When both the HDMI cable and optical cable are connected, the HDMI signal is received rst.

• When you use an optical cable and the terminals have covers, be sure to remove the covers.

AUX IN

USB (5V 0.5A)

DIGITAL AUDIO IN

(OPTICAL)

OPTICAL OUT

Optical Cable

(not supplied)

Bottom of the Soundbar

󰟳

󰟴

Top of the Soundbar

D.IN

1. Connect the DIGITAL AUDIO IN (OPTICAL) port on the Soundbar to the OPTICAL OUT port of the

TV with a digital Optical Cable (not supplied).

2. Press the (Source) button on the top panel or remote control, and then select the “D.IN” mode.

ENG - 14

Method 2. Connecting Wirelessly

Connecting a TV via Bluetooth

When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

• Only one TV can be connected at a time.

SOUND

MODE

PAIR

OR

The initial connection

1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode.

(OR)

a. Press the (Source) button on the top panel and then select “BT”.

“BT” changes to “BT PAIRING” in a few seconds automatically or changes to “BT READY” if

there is a connect record.

b. When “BT READY” appears, press and hold the (Source) button on the top panel of the

Soundbar for more than 5 seconds to display “BT PAIRING”.

2. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)

3. Select “[AV] Samsung Soundbar A5-Series” from the list on TV’s screen.

An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device

list. To connect the TV to the Soundbar, select the message, and then establish a connection.

• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.

4. You can now hear TV sound from the Soundbar.

If the device fails to connect

• If a previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar A5-Series”) appears in

the list, delete it.

• Then repeat steps 1 through 3.

NOTE

• After you have connected the Soundbar to your TV the rst time, use the “BT READY” mode to

reconnect.

ENG - 15

Disconnecting the Soundbar from the TV

Press the (Source) button on the top panel or on the remote control and switch to any mode but “BT”.

• Disconnecting takes time because the TV must receive a response from the Soundbar.

(The time required may differ, depending on the TV model.)

• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the

Left button

on the remote control for 5 seconds with the Soundbar in “BT READY” status. (Toggle On → Off)

What is the difference between BT READY and BT PAIRING?

• BT READY : In this mode, you can search for previously connected TVs or connect a previously

connected mobile device to the Soundbar.

• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR button

on the remote control or press and hold the (Source) button on the top of the Soundbar for

more than 5 seconds while the Soundbar is in “BT” mode.)

NOTES

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the

Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 20 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following

circumstances:

– If there is a strong electrical eld around the Soundbar.

– If two or more Bluetooth devices are simultaneously paired with the Soundbar.

– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

ENG - 16

05 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via a wired connection or Bluetooth connection to play the external

device’s sound through the Soundbar.

Connecting using an HDMI Cable

HDMI

HDMI TO TV

(ARC)

HDMI OUT

HDMI IN

(ARC)

HDMI Cable

Bottom of the Soundbar

󰟳

󰟴

External Device

󰟶

Top of the Soundbar

󰟵

HDMI

1. Connect an HDMI cable from the HDMI port on the back of the product to the HDMI OUT port on

your digital device.

2. Connect an HDMI cable from the HDMI TO TV (ARC) port on the back of the product to the HDMI IN

port on your TV.

3. Press the (Source) button on the top panel or on the remote control, and then select “HDMI”.

4. “HDMI” mode is displayed on the Soundbar display panel and sound plays.

ページが読み込まれています...

Samsung HW-A550 ユーザーマニュアル

Samsung HW-A550 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント