Philips HQ912/15 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル

このマニュアルも適しています

ENGLISH
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving heads
3 Shaving unit
4 Hair chamber
5 Charging light (HQ916: with battery-low
indication)
6 On/off button
7 Socket for small plug
8 Wheel of retaining frame
9 Retaining frame
10 Cutter
11 Guard
12 Release button
13 Cleaning brush
14 Adapter
15 Small plug
16 Philips Cleaning Spray (HQ110) (Optional)
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
- Warning: Keep the adapter dry.
- This symbol means: Forbidden to rinse the
adapter under a running tap (Fig. 2).
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This washable shaver is not suitable for shaving
in the shower (Fig. 3).
- Warning: Do not use this appliance close to a
bathtub, shower or other containers lled with
water.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that
they do not play with the appliance.
Caution
- Do not use the shaver or the adapter if it is
damaged.
- Only use the adapter supplied.
- If the adapter is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
- Charge, use and store the shaver at a
temperature between 5°C and 35°C.
- Warning: Remove the detachable cord from
the handheld part before cleaning this part in
water.
- Be careful with hot water. Always check if the
water is not too hot, to avoid burning your
hands.
- Do not immerse the shaver in water or
another liquid
- Do not use the shaver in combination with
pre-shave lotions, creams, foams, gels or other
cosmetic products.
Register your product and get support at
www.philips.com/welcome
HQ988, HQ916, HQ915, HQ912
4222.002.5282.3
1
2
3 4
5
6 7
8 9
10
11
12 13
14
15 16
17
18 19
20 21
22
23
24 25
26
27 28
General
- This shaver can be safely cleaned under the tap.
- This symbol means: Suitable to be cleaned
under a running tap (Fig. 4).
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
Compliance with standards
- This Philips appliance complies with all
standards regarding electromagnetic elds
(EMF). If handled properly and according to the
instructions in this user manual, the appliance
is safe to use based on scientic evidence
available today.
- This shaver complies with the applicable IEC
safety standards.
Charging
Make sure the shaver is switched off when you
start to charge it.
When you charge the shaver for the rst time
or after a long period of non-use, let it charge
continuously for 16 hours. Charging normally takes
approx. 8 hours.
For optimal performance, only charge the shaver
when the battery is low.
Do not leave the appliance connected to the
mains for more than 24 hours.
Charge indications
Charging
- When the shaver is charging, the charging light
lights up green continuously (Fig. 5).
Battery low
- HQ916: the charging light lights up orange
continuously.
- HQ988/HQ915/HQ912: the motor stops or
starts running slower.
Charging the appliance
Charge the appliance when the charging light lights
up orange (HQ916) or when the motor stops or
starts running slower (HQ988/HQ915/HQ912).
1 Put the small plug in the shaver (Fig. 6).
2 Put the adapter in the wall socket.
, The charging light goes on to indicate that
the appliance is charging (Fig. 5).
Note: Charge the shaver for at least 8 hours but not
more than 24 hours.
3 Remove the adapter from the wall socket and
pull the small plug out of the shaver when the
battery is fully charged (Fig. 7).
Note: The shaver does not run from the mains. When
the battery is empty, you have to recharge the battery
before you can use the shaver again.
Cordless shaving time
When the shaver is fully charged, it has a shaving
time of approximately 30 minutes.
Using the appliance
Note: The shaver cannot be used directly from the
mains.
1 Remove the protection cap.
2 Press the on/off button to switch on the
shaver (Fig. 8).
3 Move the shaving heads over your skin. Make
both straight and circular movements (Fig. 9).
Note: Shave on a dry face only. Do not use the shaver
in combination with gel, foam or water.
Note: Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
4 Press the on/off button to switch off the
shaver.
5 Clean the shaver after every shave (see
chapter ‘Cleaning and maintenance’).
6 Put the protection cap on the shaver
to prevent damage and to avoid dirt
accumulation in the shaving heads (Fig. 10).
Note: Make sure that the lug of the protection cap
covers the release button.
Cleaning and maintenance
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as petrol or acetone to
clean the appliance.
Clean the shaver after every shave to guarantee
better shaving performance. For the best cleaning
result, we advise you to use Philips Cleaning Spray
(HQ110). Ask your Philips dealer for information.
Note: Philips Shaving Head Cleaning Spray (HQ110)
may not be available in all countries. Contact the
Consumer Care Centre in your country about the
availability of this accessory.
After every shave: shaving unit and hair
chamber
Warning: Remove the detachable cord from the
handheld part before cleaning this part in water.
Be careful with hot water. Always check if the
water is not too hot, to avoid burning your hands.
1 Switch off the shaver, remove the adapter
from the wall socket and pull the small plug
out of the shaver.
2 Rinse the outside of the shaving unit under a
hot tap for some time (Fig. 11).
3 Press the release button (1) and pull the
shaving unit in a straight upward movement
off the shaver (2). (Fig. 12)
4 Rinse the inside of the shaving unit under
a hot tap for some time (Fig. 13).
5 Rinse the hair chamber under a hot tap for
some time (Fig. 14).
6 Put the shaving unit back onto the
shaver (Fig. 15).
Every two months: shaving heads
Note: Do not use cleaning agents or alcohol to clean
the shaving heads. Only use Philips Cleaning Spray
(HQ110).
1 Switch off the shaver, remove the adapter
from the wall socket and pull the small plug
out of the shaver.
2 Press the release button (1) and pull the
shaving unit in a straight upward movement
off the shaver (2) (Fig. 12).
3 Turn the orange wheel anticlockwise (1) and
remove the retaining frame (2) (Fig. 16).
4 Remove and clean one shaving head at a
time. Each shaving head consists of a cutter
and a guard (Fig. 17).
Note: Do not clean more than one cutter and
guard at a time, since they are all matching sets.
If you accidentally mix up the cutters and guards,
it may take several weeks before optimal shaving
performance is restored.
5 Remove the guard from the cutter (Fig. 18).
6 Clean the cutter with the short-bristled side
of the cleaning brush. Brush carefully in the
direction of the arrows (Fig. 19).
7 Clean the guard with the long-bristled side of
the cleaning brush (Fig. 20).
8 Put the cutter back into the guard after
cleaning (Fig. 21).
9 Put the shaving heads back into the shaving
unit (Fig. 22).
10 Put the retaining frame back into the shaving
unit (1) and turn the orange wheel clockwise
(2) (Fig. 23).
11 Put the shaving unit back onto the
shaver (Fig. 15).
Storage
Store the appliance in a dry place.
Store the appliance at a temperature between 5°C
and 35°C.
1 Switch off the shaver.
2 Put the protection cap on the shaver after
use to prevent damage and to avoid dirt
accumulation in the shaving heads (Fig. 10).
Note: Make sure that the lug of the protection cap
covers the release button.
Replacement
Replace the shaving heads every two years for
optimal shaving results.
Replace damaged or worn shaving heads with
Philips HQ56 shaving heads only.
For instructions on how to remove the shaving
heads, see chapter ‘Cleaning and maintenance’,
section ‘Every two months: shaving heads’.
Accessories
To retain the top performance of your shaver,
make sure you clean it regularly and replace its
shaving heads at the recommended time.
Shaving heads
- We advise you to replace your shaving heads
every two years. Always replace them with
Philips HQ56 shaving heads only (Fig. 24).
Cleaning
- Use Philips Cleaning Spray (HQ110) to clean
the shaving heads thoroughly.
Environment
- Do not throw away the appliance with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 25).
- The built-in rechargeable battery
contains substances that may pollute the
environment. Remove the battery before you
discard and hand in the appliance at an ofcial
collection point. Dispose of the battery at an
ofcial collection point for batteries. If you have
trouble removing the battery, you can also take
the appliance to a Philips service centre. The
staff of this centre will remove the battery for
you and will dispose of it in an environmentally
safe way (Fig. 26).
警告
-
电源适配器内含有一个变压器。切勿自行更换
插头,否则将导致严重后果。 电源软线不能更
换,如果软线损坏,此器具(电源适配器)应
废弃
- 警告符号注释:禁止在洗澡或淋浴时使
用。(图 3)
- 警告:不要在盛水的浴缸、淋浴、洗脸盆
或其他器皿附近使用本器具。(图3)
- 本产品不打算由肢体不健全、感觉或精神
上有障碍或缺乏相关经验和知识的人(包
括儿童)使用,除非有负责他们安全的人
对他们使用本产品进行监督或指导。
- 应照看好儿童,确保他们不玩耍本产品。
注意
- 如果剃须刀或适配器已损坏,请勿再使
用。
- 只能使用随附的适配器。
- 如果适配器已损坏,则务必更换原装型号
适配器,以免发生危险。
- 必须在 5 摄氏度至 35 摄氏度之间的温度
下充电、使用和存放剃须刀。
- 警告:将手持部分与电源软线分开后,才
能在水中清洗手持部分。
- 使用热水时一定要小心。切记先检查水温
是否太高,以防手被烫伤。
- 不要将剃须刀浸入水中或其他液体中
- 请勿将本剃须刀与剃须润滑液、面霜、泡
沫、凝胶或其它护肤产品结合使用。
概述
- 这款剃须刀可放心在水龙头下清洗。
- 符号注释:适合用在打开的水龙头下进行
清洗。 (图 4)
- 电源适配器可将 100-240 伏的电压转换为
24 伏以下的安全低电压。
符合标准
- 这款飞利浦产品符合关于电磁场 (EMF) 的
相关标准。据目前的科学证明,如果正确
使用并按照本用户手册中的说明进行操
作,本产品是安全的。
- 这款剃须刀符合 IEC 家电安全标准。
充电
请确保开始充电前,剃须刀电源已关闭。
如果是第一次为剃须刀充电,或长时间未使用
后充电,应让其连续充电 16 小时。充电通常
需要约 8 小时。
为确保最佳性能,只能在电池电量不足时为剃
须刀充电。
不要将本产品与电源接通超过 24 小时。
Problem Possible cause Solution
The
appliance
makes a
strange
noise.
Too much dirt
has collected
in the shaving
heads.
Clean the shaving
heads. After
cleaning, lubricate
the central point
on the inside of the
guards with Philips
Cleaning Spray
(HQ110). See
chapter ‘Cleaning
and maintenance’.
The shaving
heads are
damaged or
worn.
Replace the shaving
heads. See chapter
‘Replacement’.
简体中文
简介
感谢您的惠顾,欢迎光临飞利浦!为了您能充
分享受飞利浦提供的支持,请在
www.philips.com/welcome 上注册您的产品。
一般说明 (图 1)
1 保护盖
2 剃须刀头
3 剃毛刀头部件
4 毛发储藏室
5 充电指示灯(HQ916:带电池电量不足指
示灯)
6 开/关按钮
7 小插头的转换插座
8 固定架的滚轮
9 固定架
10 刀片
11 网罩
12 释放钮
13 清洁刷
14 适配器
15 小插头
16 飞利浦清洁喷雾剂 (HQ 110)(可选)
注意事项
使用本产品之前,请仔细阅读本使用说明书,
并妥善保管以备日后参考。
危险
- 警告:保持适配器干燥。
- 警告符号注释:禁止用在打开的水龙头下
进行清洗适配器。(图 2)
Problem Possible cause Solution
The shaving
heads are
damaged or
worn.
Replace the shaving
heads. See chapter
‘Replacement’.
The
shaver
does not
work
when I
press the
on/off
button.
The
rechargeable
battery is
empty.
Recharge the
battery. See
chapter ‘Charging’.
My skin is
irritated
after
shaving.
Your skin
needs time
to get used
to the Philips
shaving
system.
Skin irritation
during the rst
2-3 weeks of use
is possible. After
this period, the skin
irritation usually
disappears.
The
rotation
speed
of the
shaving
heads is
slower
than usual.
Too much dirt
has collected
in the shaving
heads.
Clean the shaving
heads. See chapter
‘Cleaning and
maintenance’.
The
rechargeable
battery is low.
Recharge the
battery. See
chapter ‘Charging’.
The
charging
light lights
up orange
(HQ916
only).
The
rechargeable
battery is low.
Recharge the
battery. See
chapter ‘Charging’.
The
appliance
becomes
warm
during
charging.
This is normal. No action required.
Removing the rechargeable battery
Only remove the rechargeable battery if it is
completely empty.
1 Remove the adapter from the wall socket and
pull the small plug out of the shaver.
2 Let the shaver run until it stops and undo the
screw at the bottom of the shaver (Fig. 27).
3 Remove the battery compartment (1) and
remove the battery (2) (Fig. 28).
Do not connect the shaver to the mains again
after you have removed the battery.
Guarantee and service
If you need service or information or if you have
a problem, please visit the Philips website at www.
philips.com or contact the Philips Consumer Care
Centre in your country. You nd its phone number
in the worldwide guarantee leaet. If there is no
Consumer Care Centre in your country, go to your
local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards) are
not covered by the terms of the international
guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the problem
with the information below, contact the Consumer
Care Centre in your country.
Problem Possible cause Solution
The
shaver
does not
shave as
well as it
used to.
The shaving
heads are
dirty. You have
not cleaned
the shaver
well enough
or you have
not cleaned
it for a long
time.
Clean the shaving
heads thoroughly
before you
continue shaving.
See chapter
‘Cleaning and
maintenance’.
Long
hairs obstruct
the shaving
heads.
Clean the cutters
and guards with
the cleaning brush
supplied. See
chapter ‘Cleaning
and maintenance’,
section ‘Every two
months: shaving
heads’.
卸下充电电池
电池电量完全耗尽后方可取出充电电池。
1 从电源插座上拔下适配器,并从剃须刀上
拔出小插头。
2 让剃须刀运行直到停止,拧下剃须刀底部
的螺钉。 (图 27)
3 卸下电池仓 (1),取出电池 (2)。 (图 28)
取出电池之后,不要再将剃须刀与电源连接
在一起。
保修与服务
如果您需要服务或更多信息,或者有任何疑
问,请访问飞利浦网站:www.philips.com。
您也可与您所在国家/地区的飞利浦客户服务
中心联系(可从全球保修卡中找到其电话号
码)。如果您所在的国家/地区没有飞利浦客
户服务中心,请与当地的飞利浦经销商联系。
保修条款
由于剃须刀头(刀片和网罩)属于易磨损物
品,因此不在国际保修条款的涵盖范围之列。
故障种类和处理方法
本章归纳了使用本产品时最可能遇到的问题。
如果您无法根据下面的信息解决问题,请联系
您所在国家/地区的飞利浦客户服务中心。
问题 可能的原因 解决方法
剃须刀的剃
须效果没有
以前好。
剃须刀头
变脏。您
没有将剃
须刀清洁
干净,或
长时间未
清洁过剃
须刀。
先彻底清洁剃须
刀头,再继续剃
须。请参阅“清
洁和维护”一
章。
过长的胡
须堵塞了
剃须刀
头。
用随附的清洁刷
清洁刀片和网
罩。见“清洁
和保养”中“每
两个月:剃须刀
头”部分。
剃须刀头
已损坏或
磨损。
更换剃须刀头。
见“更换”一
章。
按下开/关钮
时,剃须刀
不工作。
充电电池
的电量已
耗尽。
给电池充电。
见“充电”一
章。
6 用清洁刷的短毛一侧清洁刀片。按箭头方
向小心地清洁。 (图 19)
7 用清洁刷的长毛一侧清洁网罩。 (图 20)
8 清洁后,将刀片重新装回至网罩。 (图 21)
9 将剃须刀头重新放入剃须刀头部件。
(图 22)
10 将固定架放回剃须刀头部件内 (1),并沿顺
时针方向转动橙色轴轮 (2)。 (图 23)
11 将剃须刀头组件重新安装到剃须刀上。
(图 15)
存储 
将本产品存放在干燥的地方。
必须在 5 摄氏度至 35 摄氏度之间的温度下存
放本产品。
1 关闭剃须刀。
2 使用后请盖上剃须刀保护盖,以防止损坏
剃须刀头并避免其内积聚灰尘。 (图 10)
注意: 确保保护盖的凸缘盖住释放钮。
更换
每两年更换一次刀头以获得最佳的剃须效果。
损坏或磨损的剃须刀头只能用 HQ56 飞利浦
剃须刀头更换。
有关如何拆卸剃须刀头的说明,请参阅“清洁
和保养”一章中的“每两个月:清洁剃须刀
头”部分。
附件
为了保持剃须刀的最佳性能,请确保定期清洁
并在推荐的时间更换剃须刀头。
剃须刀头
- 建议您每两年更换一次剃须刀头。务必仅
使用 HQ56 飞利浦剃须刀头进行更换。
(图 24)
清洁
- 使用飞利浦清洁喷雾剂 (HQ110) 彻底清洁
剃须刀头。
环保
- 弃置产品时,请不要将其与一般生活垃圾
堆放在一起;应将其交给官方指定的回收
点。这样做有利于环保。 (图 25)
- 内置充电电池含有可能会污染环境的物
质。弃置产品并将产品送到官方指定的回
收站之前,应将电池取出。到官方指定的
电池回收站处理电池。如果您在取出电池
时遇到问题,您也可以将产品送至飞利浦
维修中心。维修中心的员工会帮您取出电
池,并以环保的方式进行处理。 (图 26)
清洁和保养
不要使用钢丝绒、研磨性清洁剂或腐蚀性液体
(例如汽油或丙酮)来清洁产品。
每次剃须后均应清洁剃须刀,以保证更好的剃
须效果。为了获得最佳的清洁效果,建议您使
用飞利浦清洁喷雾剂 (HQ110)。有关详情,请
咨询飞利浦经销商。
注意: 并非所有国家/地区都销售飞利浦剃须
刀头清洁喷雾剂 (HQ110)。请向当地的客户服
务中心了解是否有售。
每次剃须后:清洗剃须刀头部件和胡茬储
藏室
警告:将手持部分与电源软线分开后,才能在
水中清洗手持部分。
使用热水时一定要小心。切记先检查水温是否
太高,以防手被烫伤。
1 关闭剃须刀电源,从电源插座上拔下适配
器,并从剃须刀上拔下小插头。
2 将剃须刀头部件的外部放在热水龙头下冲
洗片刻。 (图 11)
3 按释放按钮 (1),垂直向上移动剃须刀头部
件,将其从剃须刀 (2) 中拉出。 (图 12)
4 将剃须刀头部件的内部放在热水龙头下冲
洗片刻。 (图 13)
5 将胡茬储藏室放在热水龙头下冲洗片刻。
(图 14)
6 将剃须刀头组件重新安装到剃须刀上。
(图 15)
每两个月:清洁剃须刀头
注意: 请勿使用清洁剂或酒精来清洁剃须刀
头。只能使用飞利浦清洁喷雾剂 (HQ110)。
1 关闭剃须刀电源,从电源插座上拔下适配
器,并从剃须刀上拔下小插头。
2 按释放按钮 (1),垂直向上移动剃须刀头部
件,将其从剃须刀 (2) 中拉出。 (图 12)
3 逆时针转动橙色轮轴 (1) 并取下固定架 (2)
。 (图 16)
4 一次取下并清洁一个剃须刀头。每个剃须
刀头包含一组刀片和网罩。 (图 17)
注意: 不要同时清洁多组刀片和网罩,因为
它们都是相互匹配的。如果不小心将刀片和网
罩弄混,则需要数周时间才能恢复产品的最佳
剃须性能。
5 从刀片上卸下网罩。 (图 18)
充电指示
充电
- 剃须刀正在充电时,充电指示灯将呈绿色
持续亮起。 (图 5)
电池电量不足
- HQ916:充电指示灯呈橙色持续亮起。
- HQ988/HQ915/HQ912:马达停止运转,
或者运转开始变得缓慢。
为产品充电
当充电指示灯呈橙色亮起时 (HQ916),或者
当马达停止运转或开始运转缓慢时 (HQ988/
HQ915/HQ912),应为产品充电。
1 将小插头插入剃须刀。 (图 6)
2 将电源适配器插入电源插座。
, 充电指示灯亮起,表示剃须刀正在充电。
(图 5)
注意: 至少让剃须刀充电 8 小时,但不要超
过 24 小时。
3 电池充满后,从电源插座中拔下适配器,
并从剃须刀上拔出小插头。 (图 7)
注意: 本剃须刀不能插电使用。当电池电量
耗尽时,请在再次使用剃须刀前为电池充电。
不接电源的剃须时间
当剃须刀充满电时,剃须时间大约为 30 分
钟。
使用本产品
注意: 剃须刀不能连在电源上直接使用。
1 取下保护盖。
2 按下开/关按钮启动剃须刀。 (图 8)
3 将剃须刀头在皮肤上移动。作直线和迂回
动作。 (图 9)
注意: 仅限在干爽的面部剃须。请勿将本剃
须刀与凝胶、剃须泡沫或水结合使用。
注意: 您的皮肤可能需要 2 到 3 周才能适应
飞利浦剃须系统。
4 按开/关按钮关闭剃须刀电源。
5 每次剃须后均应清洁剃须刀(见“清洁和
保养”一章)。
6 请盖上剃须刀保护盖,以防止损坏剃须刀
头并避免其内积聚灰尘。 (图 10)
注意: 确保保护盖的凸缘盖住释放钮。
问题 可能的原因 解决方法
我在剃须后
出现皮肤过
敏。
您的皮肤
需要一定
的时间来
适应飞
利浦剃须
刀。
在前 2-3 周的
使用过程中,可
能会出现皮肤过
敏。在此之后,
皮肤过敏通常会
消失。
剃须刀头的
转速比平时
慢。
剃须刀头
中积聚了
太多的灰
尘。
清洁剃须刀头。
请参阅“清洁和
保养”一章。
充电电池
的电量不
足。
给电池充电。
见“充电”一
章。
充电指示灯
呈橙色亮起
(仅限于
HQ916)。
充电电池
的电量不
足。
给电池充电。
见“充电”一
章。
产品在充电
过程中变
热。
这是正常
的。
不需要采取措
施。
产品发出奇
怪的噪音。
剃须刀头
中积聚了
太多的灰
尘。
清洁剃须刀头。
清洁后,用飞
利浦清洁喷雾
剂 (HQ110) 润
滑网罩内侧的中
央点。请参阅“
清洁和保养”一
章。
剃须刀头
已损坏或
磨损。
更换剃须刀头。
见“更换”一
章。
HQ915
220V
50Hz
2 W
519040
: 4008 800 008
GB4706.1-2005,
GB4706.9-2008
IPX4
1 / 1

Philips HQ912/15 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル
このマニュアルも適しています

他の言語で