Hilti TE 50-AVR ユーザーマニュアル

TE 50-AVR

English 1

ﻋﺮﺑﻲ 11

日本語 21

한국어 31

繁體中文 41

中文 50

TE 50-AVR

en Originaloperatinginstructions....................................... 1

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 11

ja オリジナル取扱説明書 ............................................ 21

ko 오리지널사용설명서............................................. 31

zh 原始操作說明.................................................. 41

cn 原版操作说明.................................................. 50

*2133068* 2133068 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage

to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

2 English 2133068 *2133068*

Drilling with hammer action (hammer drilling)

Chiseling

Chisel positioning

Protection class II (double-insulated)

Revolutions per minute

Rated speed under no load

Diameter

Wireless data transfer

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Combihammer TE 50AVR

Generation 03

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

*2133068* 2133068 English 3

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or the battery pack from the power tool before

making any adjustments, changing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and

any other condition that may affect the power tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poorly maintained power tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

2.2 Hammer safety warnings

▶Wear ear protectors. Exposure to noise can cause hearing loss.

▶Use auxiliary handles, if supplied with the tool. Loss of control can cause personal injury.

▶Hold power tool by insulated gripping surfaces, when performing an operation where the cutting

accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and could give the operator an electric shock.

4 English 2133068 *2133068*

2.3 Additional safety instructions

Personal safety

▶Use the product only when it is in technically faultless condition.

▶Never tamper with or modify the power tool in any way.

▶Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking

through. Parts breaking away could fall out and / or fall down causing injury to other persons.

▶Always hold the power tool with both hands on the grips provided. Keep the grips clean and dry.

▶Always grip the side handle at its outermost end. When drilling and screwdriving, the grip of the power

tool may be deflected laterally (the power tool tends to pivot about its own axis).

▶Avoid touching rotating parts – risk of injury!

▶Wear suitable protective glasses, a hard hat, ear protection, protective gloves and light respiratory

protection while using the power tool.

▶Wear protective gloves also when changing the accessory tool. Touching the accessory tool presents a

risk of injury (cuts or burns).

▶Wear eye protection. Flying fragments present a risk of injury to the body and eyes.

▶Before beginning the work, check the hazard classification of the dust that will be produced. Use an

industrial vacuum cleaner with an officially approved protection classification in compliance with locally

applicable dust protection regulations.

▶Use a dust removal system and suitable vacuum cleaner whenever possible. Dust from materials, such

as paint containing lead, some wood species, concrete/masonry/stone containing silica, and minerals as

well as metal, may be harmful.

▶Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for

the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or

respiratory or other diseases to the operator or bystanders. Certain kinds of dust are classified as

carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning

(chromate, wood preservative). Material containing asbestos may be handled only by specialists.

▶Take breaks between working and do physical exercises to improve the blood circulation in your fingers.

Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous

system in the fingers, hands and wrists.

Electrical safety

▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the power tool may become live, presenting a risk of electric shock, if you damage

an electric cable accidentally.

Careful handling and use of power tools

▶Switch the power tool off if the accessory tool sticks and stalls. The power tool may be deflected laterally.

▶Wait until the power tool stops completely before you lay it down.

*2133068* 2133068 English 5

3 Description

3.1 Overview of the product 1

@Chuck

;Depth gauge

=Function selector switch

%Control switch

&Service indicator

(AVR

)Supply cord

+Side handle

3.2 Version with detachable supply cord 2

@Lockbutton

;Connector on electric tool

=Supply cord with keyed, releasable plug

connector

3.3 Intended use

The product described is an electrically-powered combihammer with pneumatic hammering mechanism. It

is designed for drilling in concrete, masonry, wood and metal. The product can also be used for light to

medium-duty chiseling on masonry and surface finishing work on concrete.

▶Operation is permissible only when connected to a power source providing a voltage and frequency in

compliance with the information given on the type identification plate.

3.4 Possible misuse

• This product is not suitable for working on hazardous materials.

• This product is not suitable for working in a damp environment.

3.5 Active Vibration Reduction

The tool is equipped with an Active Vibration Reduction (AVR) system which reduces vibration noticeably.

3.6 Quick-release chuck (accessory)

The quick-release chuck makes it possible to change accessory tools quickly, without need for a chuck key

(keyless system). It is suitable for accessory tools with a cylindrical or hexagonal shank, such as drill bits for

wood and metal, or mixing paddles, which are used in the rotary-only mode (without hammering action) .

6 English 2133068 *2133068*

3.7 Service indicator

The product has an LED service indicator.

Status Meaning

Service indicator shows Servicing is due.

Service indicator flashes The product is faulty. Have the combihammer re-

paired by Hilti Service.

3.8 Items supplied

Combihammer, side handle, operating instructions.

Other system products approved for use with this product can be found at your local Hilti Store or online at:

www.hilti.group.

4 Technical data

4.1 Combihammer

For rated voltage, rated current, frequency and/or input power, refer to the country-specific type

identification plate.

If the device is powered by a generator or transformer, the generator or transformer’s power output must be

at least twice the rated input power shown on the rating plate of the device. The operating voltage of the

transformer or generator must always be within +5 % and -15 % of the rated voltage of the device.

TE 50AVR

Weight in accordance with EPTA procedure 01 6.1 kg

Storage temperature −20 ℃ … 70 ℃

Ambient temperature for operation −17 ℃ … 60 ℃

Ø hammer drill bits 12 mm … 32 mm

Ø drill bits for wood 6 mm … 35 mm

Ø drill bits for metal 6 mm … 13 mm

4.2 Noise information and vibration values determined in accordance with EN 60745

The sound pressure and vibration values given in these instructions have been measured in accordance

with a standardized test and may be used to compare one electric tool with another. They may be used

for a preliminary assessment of exposure. The data given represents the main applications of the electric

tool. However, if the electric tool is used for different applications, with different accessory tools, or is poorly

maintained, the data may vary. This may significantly increase exposure over the total working period. An

accurate estimation of exposure should also take into account the times when the tool is switched off, or

when it is running but not actually being used for a job. This may significantly reduce exposure over the

total working period. Identify additional safety measures to protect the operator from the effects of noise

and/or vibration, for example: maintenance of the electric tool and the accessories, keeping the hands warm,

organization of work patterns.

Noise emission values

TE 50AVR

Sound (power) level (LWA)108 dB(A)

Uncertainty for the sound power level (KWA)3 dB(A)

Sound pressure level (L pA)97 dB(A)

Uncertainty for the sound pressure level (KpA)3 dB(A)

Total vibration

TE 50AVR

Drilling in metal (ah,D)< 5 m/s²

Hammer drilling in concrete (ah,HD)9 m/s²

*2133068* 2133068 English 7

TE 50AVR

Chiseling (ah,Cheq)8 m/s²

Uncertainty for the given vibration value (K) 1.5 m/s²

5 Operation

5.1 Preparations at the workplace

CAUTION

Risk of injury! Inadvertent starting of the product.

▶Unplug the supply cord before making adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1.1 Fitting the side handle 3

1. Release the side handle clamping band by turning the handle grip.

2. Slide the side handle clamping band over the chuck from the front and into the recess provided.

3. Bring the side handle into the desired position.

4. Tighten the side handle clamping band by turning the handle grip.

5.1.2 Fitting the depth gauge (optional) 4

1. Release the side handle clamping band by turning the handle grip.

2. Slide the depth gauge from the front into the 2 guide holes provided.

3. Tighten the side handle clamping band by turning the handle grip.

➥ The depth gauge is fitted. To set the drilling depth:

4. Release the screw at the depth gauge.

5. Adjust the depth gauge to the desired drilling depth.

6. Tighten the screw at the depth gauge.

5.1.3 Fitting/removing the accessory tool 5

CAUTION

Risk of injury! The accessory tool gets hot during use.

▶Wear protective gloves when changing the accessory tool.

▶Do not place the hot accessory tool on readily flammable materials.

1. Apply a little grease to the connection end of the accessory tool.

2. Push the accessory tool into the chuck as far as it will go (until it engages).

➥ The product is ready for use.

3. Pull the chuck back as far as it will go and remove the accessory tool.

Use only the recommended grease supplied by Hilti. Use of unsuitable grease may cause damage

to the product.

5.2 Types of work

ATTENTION

Risk of damage by incorrect handling!

▶Do not operate the switches for direction of rotation and/or function selection during operation.

Observe the safety instructions and warnings in this documentation and on the product.

5.2.1 Drilling with hammering action (hammer drilling) 6

1. Set the function selector switch to the “Hammer drilling” position .

2. Press the drill bit against the work surface.

3. Press the control switch.

➥ The product starts.

8 English 2133068 *2133068*

5.3 Chisel positioning 7

CAUTION

Risk of injury! Loss of control over the chisel direction.

▶Do not operate the tool when the selector switch is set to “Chisel positioning”. Turn the function selector

switch until it engages in the “Chiseling” position.

The chisel can be adjusted to 24 different positions (in 15° increments). This ensures that flat chisels

and shaped chisels can always be set to the optimum working position.

1. Set the function selector switch to the “Chisel positioning” position .

2. Rotate the chisel to the desired position.

3. Turn the function selector switch until it engages in the “Chiseling” position.

➥ The product is ready for use.

5.3.1 Chiseling 8

▶Set the function selector switch to the “Chiseling” position .

5.3.2 Switching sustained operation on and off 9

When chiseling, the on/off switch can be locked in the “on” position.

1. Push the lockbutton for continuous operation forward.

2. Press the on/off switch as far as it will go.

➥ The product then runs in sustained operating mode.

3. Push the lockbutton for continuous operation back.

➥ The product switches off.

6 Detachable supply cord

6.1 Connecting the detachable supply cord

CAUTION

Risk of injury! Due to leakage current as a result of dirty contacts.

▶Connect the detachable electric connector to the electric tool only when it is clean and dry and when the

supply cord is unplugged from the power outlet.

1. Push the keyed, detachable electric plug connector into the socket as far as it will go, until it is heard to

engage.

2. Plug the supply cord into the power outlet.

6.2 Disconnecting the detachable supply cord

1. Unplug the supply cord from the power outlet.

2. Press the release button and pull the keyed, detachable electric plug connector out of the socket.

3. Pull the supply cord connector out of the power tool.

7 Care and maintenance

WARNING

Electric shock hazard! Attempting care and maintenance with the supply cord connected to a power outlet

can lead to severe injury and burns.

▶Always unplug the supply cord before carrying out care and maintenance tasks.

Care

• Carefully remove any dirt that may be adhering to parts.

• Clean the air vents carefully with a dry brush.

*2133068* 2133068 English 9

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these may attack the plastic parts.

Maintenance

WARNING

Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including

burns.

▶Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical

specialists.

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

8 Transport and storage

• Do not transport electric tools with accessory tools fitted.

• Always unplug the supply cord before storing an electric tool or appliance.

• Store tools and appliances in a dry place where they cannot be accessed by children or unauthorized

persons.

• Check electric tools or appliances for damage after long periods of transport or storage.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

9.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

The power tool doesn’t start. Interruption in the electric supply. ▶Plug in another electric tool or

appliance and check whether it

works.

The electronic restart interlock is

activated after an interruption in

the electric supply.

▶Switch the power tool off and

then on again.

No hammering action. The power tool is too cold. ▶Bring the tip of the drill bit

into contact with the working

surface, switch the rotary

hammer on and allow it to

run. If necessary, repeat the

procedure until the hammering

mechanism begins to operate.

The combihammer doesn’t

achieve full power. The gauge (cross section) of the

extension cord conductors is inad-

equate.

▶Use an extension cord with

an adequate conductor cross

section.

The voltage provided by the elec-

tric supply is too low.

▶Connect the combihammer to a

different electric supply.

The drill bit doesn’t rotate. The function selector switch is not

engaged or is in the “Chiseling”

or “Chisel adjustment” position.

▶Set the function selector switch

to the “Hammer drilling” position

10 English 2133068 *2133068*

Trouble or fault Possible cause Action to be taken

The drill bit can’t be released. The chuck is not pulled back fully. ▶Pull the chuck back as far

as it will go and remove the

accessory tool.

The side handle is not fitted cor-

rectly.

▶Release the side handle and refit

it correctly so that the clamping

band and side handle engage in

the recess.

The service indicator lights

after changing the carbon

brushes.

The contact surfaces are not yet

run in.

▶Run in the carbon brushes by

allowing the power tool to run

under no load for at least 1

minute without interruption.

10 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

11 RoHS (Restriction of Hazardous Substances)

Click on the link to go to the table of hazardous substances: qr.hilti.com/r4902202.

There is a link to the RoHS table, in the form of a QR code, at the end of this document.

12 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

*2133068* 2133068 ﻋﺮﺑﻲ 11

1ﺑﻴﺎﻧﺎﺕﺍﻟﻤﺴﺘﻨﺪ

1.1ﺣﻮﻝﻫﺬﺍﺍﻟﻤﺴﺘﻨﺪ

•

ﺍﻗﺮﺃﻫﺬﻩﺍﻟﻤﺴﺘﻨﺪﺍﺕﺑﺎﻟﻜﺎﻣﻞﻗﺒﻞﺍﻟﺘﺸﻐﻴﻞ.ﻳﻌﺘﺒﺮﻫﺬﺍﺷﺮﻃﺎﻟﻠﻌﻤﻞﺑﺸﻜﻞﺁﻣﻦﻭﺍﻻﺳﺘﺨﺪﺍﻡﺑﺪﻭﻥ ﺍﺧﺘﻼﻻﺕ. •

ﺗﺮﺍﻋﻰﺇﺭﺷﺎﺩﺍﺕﺍﻷﻣﺎﻥﻭﺍﻹﺭﺷﺎﺩﺍﺕﺍﻟﺘﺤﺬﻳﺮﻳﺔﺍﻟﻮﺍﺭﺩﺓﻓﻲﻫﺬﺍﺍﻟﻤﺴﺘﻨﺪﻭﻋﻠﻰﺍﻟﺠﻬﺎﺯ.

•

ﺍﺣﺘﻔﻆﺑﺪﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺩﺍﺋﻤﺎﻣﻊﺍﻟﻤﻨﺘﺞ،ﻭﻻﺗﻌﻄﻲﺍﻟﺠﻬﺎﺯﻵﺧﺮﻳﻦﺇﻻﻣﺮﻓﻘﺎﺑﻬﺬﺍﺍﻟﺪﻟﻴﻞ.

1.2ﺷﺮﺡﺍﻟﻌﻼﻣﺎﺕ

1.2.1ﺇﺭﺷﺎﺩﺍﺕﺗﺤﺬﻳﺮﻳﺔ

ﺗﻨﺒﻪﺍﻹﺭﺷﺎﺩﺍﺕﺍﻟﺘﺤﺬﻳﺮﻳﺔﺇﻟﻰﺍﻷﺧﻄﺎﺭﺍﻟﻨﺎﺷﺌﺔﻋﻨﺪﺍﻟﺘﻌﺎﻣﻞﻣﻊﺍﻟﺠﻬﺎﺯ.ﻳﺘﻢﺍﺳﺘﺨﺪﺍﻡﺍﻟﻜﻠﻤﺎﺕﺍﻟﺪﻟﻴﻠﻴﺔﺍﻟﺘﺎﻟﻴﺔ:

ﺧﻄﺮ

ﺧﻄﺮ!

◀

ﺗﺸﻴﺮﻟﺨﻄﺮﻣﺒﺎﺷﺮﻳﺆﺩﻱﻹﺻﺎﺑﺎﺕﺟﺴﺪﻳﺔﺧﻄﻴﺮﺓﺃﻭﺇﻟﻰﺍﻟﻮﻓﺎﺓ.

ﺗﺤﺬﻳﺮ

ﺗﺤﺬﻳﺮ!

◀

ﺗﺸﻴﺮﻟﺨﻄﺮﻣﺤﺘﻤﻞﻗﺪﻳﺆﺩﻱﻹﺻﺎﺑﺎﺕﺟﺴﺪﻳﺔﺧﻄﻴﺮﺓﺃﻭﺇﻟﻰﺍﻟﻮﻓﺎﺓ.

ﺍﺣﺘﺮﺱ:

ﺍﺣﺘﺮﺱ!

◀

ﺗﺸﻴﺮﻟﻤﻮﻗﻒﺧﻄﺮﻣﺤﺘﻤﻞﻳﻤﻜﻦﺃﻥﻳﺆﺩﻱﻹﺻﺎﺑﺎﺕﺟﺴﺪﻳﺔﺧﻔﻴﻔﺔﺃﻭﺃﺿﺮﺍﺭﻣﺎﺩﻳﺔ.

1.2.2ﺍﻟﺮﻣﻮﺯﻓﻲﺍﻟﻤﺴﺘﻨﺪ

ﻳﺘﻢﺍﺳﺘﺨﺪﺍﻡﺍﻟﺮﻣﻮﺯﺍﻟﺘﺎﻟﻴﺔﻓﻲﻫﺬﺍﺍﻟﻤﺴﺘﻨﺪ:

ﻗﺒﻞﺍﻻﺳﺘﺨﺪﺍﻡﺍﻗﺮﺃﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝ

ﺇﺭﺷﺎﺩﺍﺕﺍﻻﺳﺘﺨﺪﺍﻡﻭﻣﻌﻠﻮﻣﺎﺕﺃﺧﺮﻯﻣﻔﻴﺪﺓ

ﺍﻟﺘﻌﺎﻣﻞﻣﻊﻣﻮﺍﺩﻗﺎﺑﻠﺔﻹﻋﺎﺩﺓﺍﻟﺘﺪﻭﻳﺮ

ﻻﺗﺘﺨﻠﺺﻣﻦﺍﻷﺟﻬﺰﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺍﻟﺒﻄﺎﺭﻳﺎﺕﺿﻤﻦﺍﻟﻘﻤﺎﻣﺔﺍﻟﻤﻨﺰﻟﻴﺔ

1.2.3ﺍﻟﺮﻣﻮﺯﻓﻲﺍﻟﺼﻮﺭ

ﺗﺴﺘﺨﺪﻡﺍﻟﺮﻣﻮﺯﺍﻟﺘﺎﻟﻴﺔﻓﻲﺍﻟﺮﺳﻮﻡﺍﻟﺘﻮﺿﻴﺤﻴﺔ:

ﺗﺸﻴﺮﻫﺬﻩﺍﻷﻋﺪﺍﺩﺇﻟﻰﺍﻟﺼﻮﺭﺍﻟﻤﻌﻨﻴﺔﺑﻤﻄﻠﻊﻫﺬﺍﺍﻟﺪﻟﻴﻞ

ﺗﺮﻗﻴﻢﺍﻟﺼﻮﺭﻳﻤﺜﻞﺗﺮﺗﻴﺐﺧﻄﻮﺍﺕﺍﻟﻌﻤﻞﻓﻲﺍﻟﺼﻮﺭ،ﻭﻗﺪﻳﺨﺘﻠﻒﻋﻦﺗﺮﻗﻴﻢﺧﻄﻮﺍﺕﺍﻟﻌﻤﻞﻓﻲﺍﻟﻨﺺ

ﻳﺘﻢﺍﺳﺘﺨﺪﺍﻡﺃﺭﻗﺎﻡﺍﻟﻤﻮﺍﺿﻊﻓﻲﺻﻮﺭﺓﺍﻟﻌﺮﺽﺍﻟﻌﺎﻡﻭﻫﻲﺗﺸﻴﺮﺇﻟﻰﺃﺭﻗﺎﻡﺗﻌﻠﻴﻖﺍﻟﺼﻮﺭﺓﻓﻲ ﻓﺼﻞﻋﺮﺽﻋﺎﻡﻟﻠﻤﻨﺘﺞ

ﻳﻨﺒﻐﻲﺃﻥﺗﺴﺘﺮﻋﻲﻫﺬﻩﺍﻟﻌﻼﻣﺔﺍﻫﺘﻤﺎﻣﺎﺧﺎﺻﺎﻋﻨﺪﺍﻟﺘﻌﺎﻣﻞﻣﻊﺍﻟﻤﻨﺘﺞ.

1.3ﺍﻟﺮﻣﻮﺯﺍﻟﻤﺮﺗﺒﻄﺔﺑﺎﻟﻤﻨﺘﺞ

1.3.1ﺍﻟﺮﻣﻮﺯﻋﻠﻰﺍﻟﻤﻨﺘﺞ

ﻳﺘﻢﺍﺳﺘﺨﺪﺍﻡﺍﻟﺮﻣﻮﺯﺍﻟﺘﺎﻟﻴﺔﻋﻠﻰﺍﻟﻤﻨﺘﺞ:

ﺍﻟﺜﻘﺐﺑﺎﻟﻄﺮﻕ)ﺍﻟﺜﻘﺐﺍﻟﻤﻄﺮﻗﻲ(

12 ﻋﺮﺑﻲ 2133068 *2133068*

ﺍﻟﻨﻘﺮﺑﺎﻹﺯﻣﻴﻞ

ﺗﺤﺪﻳﺪﻣﻮﺿﻊﺍﻹﺯﻣﻴﻞ

ﻓﺌﺔﺍﻟﺤﻤﺎﻳﺔII)ﻋﺰﻝﻣﺰﺩﻭﺝ(

ﻋﺪﺩﺍﻟﻠﻔﺎﺕﻓﻲﺍﻟﺪﻗﻴﻘﺔ

ﻋﺪﺩﺍﻟﻠﻔﺎﺕﺍﻻﺳﻤﻲﻓﻲﺍﻟﻮﺿﻊﺍﻟﻤﺤﺎﻳﺪ

ﺍﻟﻘﻄﺮ

ﻧﻘﻞﺍﻟﺒﻴﺎﻧﺎﺕﻻﺳﻠﻜﻴﺎً

1.4ﻣﻌﻠﻮﻣﺎﺕﺍﻟﻤﻨﺘﺞ

ﻣﻨﺘﺠﺎﺕﻣﺼﻤﻤﺔﻟﻠﻤﺴﺘﺨﺪﻣﻴﻦﺍﻟﻤﺤﺘﺮﻓﻴﻦﻭﻳﻘﺘﺼﺮﺍﺳﺘﻌﻤﺎﻟﻬﺎﻭﺻﻴﺎﻧﺘﻬﺎﻭﺇﺻﻼﺣﻬﺎﻋﻠﻰﺍﻷﺷﺨﺎﺹ ﺍﻟﻤﻌﺘﻤﺪﻳﻦﻭﺍﻟﻤﺪﺭﺑﻴﻦﺟﻴﺪﺍ.ﻫﺆﻻءﺍﻷﺷﺨﺎﺹﻳﺠﺐﺃﻥﻳﻜﻮﻧﻮﺍﻗﺪﺗﻠﻘﻮﺍﺗﺪﺭﻳﺒﺎﺧﺎﺻﺎﻋﻠﻰﺍﻷﺧﻄﺎﺭﺍﻟﻄﺎﺭﺋﺔ.ﻗﺪ ﻳﺘﺴﺒﺐﺍﻟﺠﻬﺎﺯﻭﺃﺩﻭﺍﺗﻪﺍﻟﻤﺴﺎﻋﺪﺓﻓﻲﺣﺪﻭﺙﺃﺧﻄﺎﺭﺇﺫﺍﺗﻢﺍﻟﺘﻌﺎﻣﻞﻣﻌﻬﺎﺑﺸﻜﻞﻏﻴﺮﺳﻠﻴﻢﻓﻨﻴﺎﻣﻦﻗﺒﻞﺃﺷﺨﺎﺹ

ﻏﻴﺮﻣﺪﺭﺑﻴﻦﺃﻭﺗﻢﺍﺳﺘﺨﺪﺍﻣﻬﺎﺑﺸﻜﻞﻏﻴﺮﻣﻄﺎﺑﻖﻟﻠﺘﻌﻠﻴﻤﺎﺕ.

ﻳﻮﺟﺪﻣﺴﻤﻰﺍﻟﻄﺮﺍﺯﻭﺍﻟﺮﻗﻢﺍﻟﻤﺴﻠﺴﻞﻋﻠﻰﻟﻮﺣﺔﺍﻟﺼﻨﻊ.

◀ﺍﻧﻘﻞﺍﻟﺮﻗﻢﺍﻟﻤﺴﻠﺴﻞﻓﻲﺍﻟﺠﺪﻭﻝﺍﻟﺘﺎﻟﻲ.ﺳﺘﺤﺘﺎﺝﺇﻟﻰﺑﻴﺎﻧﺎﺕﺍﻟﻤﻨﺘﺞﻓﻲﺣﺎﻟﺔﺍﻻﺳﺘﻔﺴﺎﺭﺍﺕﺍﻟﻤﻮﺟﻬﺔﺇﻟﻰ

ﻣﻤﺜﻠﻴﻨﺎﺃﻭﻣﺮﻛﺰﺍﻟﺨﺪﻣﺔ.

ﺑﻴﺎﻧﺎﺕﺍﻟﻤﻨﺘﺞ

ﺍﻟﻤﻄﺮﻗﺔﻣﺘﻌﺪﺩﺓﺍﻷﻏﺮﺍﺽ

TE 50AVR

ﺍﻟﺠﻴﻞ03

ﺍﻟﺮﻗﻢﺍﻟﻤﺴﻠﺴﻞ

1.5ﺑﻴﺎﻥﺍﻟﻤﻄﺎﺑﻘﺔ

ﻧﻘﺮﻋﻠﻰﻣﺴﺌﻮﻟﻴﺘﻨﺎﺍﻟﻔﺮﺩﻳﺔﺑﺄﻥﺍﻟﻤﻨﺘﺞﺍﻟﻤﺸﺮﻭﺡﻫﻨﺎﻣﺘﻮﺍﻓﻖﻣﻊﺍﻟﺘﺸﺮﻳﻌﺎﺕﻭﺍﻟﻤﻮﺍﺻﻔﺎﺕﺍﻟﻤﻌﻤﻮﻝﺑﻬﺎ.ﺗﺠﺪ ﺻﻮﺭﺓﻟﺒﻴﺎﻥﺍﻟﻤﻄﺎﺑﻘﺔﻓﻲﻧﻬﺎﻳﺔﻫﺬﺍﺍﻟﻤﺴﺘﻨﺪ.

ﺍﻟﻤﺴﺘﻨﺪﺍﺕﺍﻟﻔﻨﻴﺔﻣﺤﻔﻮﻇﺔﻫﻨﺎ:

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2ﺍﻟﺴﻼﻣﺔ

2.1ﺇﺭﺷﺎﺩﺍﺕﺍﻟﺴﻼﻣﺔﺍﻟﻌﺎﻣﺔﺍﻟﻤﺘﻌﻠﻘﺔﺑﺎﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ

ﺗﺤﺬﻳﺮﺍﺣﺮﺹﻋﻠﻰﻗﺮﺍءﺓﺟﻤﻴﻊﺇﺭﺷﺎﺩﺍﺕﺍﻟﺴﻼﻣﺔﻭﺍﻟﺘﻌﻠﻴﻤﺎﺕ.ﺃﻱﺗﻘﺼﻴﺮﺃﻭﺇﻫﻤﺎﻝﻓﻲﺗﻄﺒﻴﻖﺇﺭﺷﺎﺩﺍﺕ

ﺍﻟﺴﻼﻣﺔﻭﺍﻟﺘﻌﻠﻴﻤﺎﺕﻗﺪﻳﺘﺴﺒﺐﻓﻲﺣﺪﻭﺙﺻﺪﻣﺔﻛﻬﺮﺑﺎﺋﻴﺔﺃﻭﺣﺮﻳﻖﻭ/ﺃﻭﺇﺻﺎﺑﺎﺕﺧﻄﻴﺮﺓ.

ﺍﺣﺘﻔﻆﺑﺠﻤﻴﻊﻣﺴﺘﻨﺪﺍﺕﺇﺭﺷﺎﺩﺍﺕﺍﻟﺴﻼﻣﺔﻭﺍﻟﺘﻌﻠﻴﻤﺎﺕﻻﺳﺘﺨﺪﺍﻣﻬﺎﻋﻨﺪﺍﻟﺤﺎﺟﺔﺇﻟﻴﻬﺎﻓﻴﻤﺎﺑﻌﺪ.

ﻳﻘﺼﺪﺑﻤﺼﻄﻠﺢ»ﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ«ﺍﻟﻮﺍﺭﺩﺫﻛﺮﻩﻓﻲﺇﺭﺷﺎﺩﺍﺕﺍﻟﺴﻼﻣﺔﺍﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺍﻟﻤﺸﻐﻠﺔﺑﺎﻟﻜﻬﺮﺑﺎء

)ﺑﺎﺳﺘﺨﺪﺍﻡﻛﺎﺑﻞﺍﻟﻜﻬﺮﺑﺎء(ﻭﻛﺬﻟﻚﺍﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺍﻟﻤﺸﻐﻠﺔﺑﺎﻟﺒﻄﺎﺭﻳﺎﺕ)ﺑﺪﻭﻥﻛﺎﺑﻞﺍﻟﻜﻬﺮﺑﺎء(.

ﺳﻼﻣﺔﻣﻜﺎﻥﺍﻟﻌﻤﻞ

◀

ﺣﺎﻓﻆﻋﻠﻰﻧﻄﺎﻕﻋﻤﻠﻚﻧﻈﻴﻔﺎﻭﻣﻀﺎءﺍﺑﺸﻜﻞﺟﻴﺪ.ﺍﻟﻔﻮﺿﻰﺃﻭﺃﻣﺎﻛﻦﺍﻟﻌﻤﻞﻏﻴﺮﺍﻟﻤﻀﺎءﺓﻳﻤﻜﻦﺃﻥﺗﺆﺩﻱ ﻟﻮﻗﻮﻉﺣﻮﺍﺩﺙ.

◀

ﻻﺗﻌﻤﻞﺑﺎﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻓﻲﻣﺤﻴﻂﻣﻌﺮﺽﻟﺨﻄﺮﺍﻻﻧﻔﺠﺎﺭﻳﺘﻮﺍﺟﺪﺑﻪﺳﻮﺍﺋﻞﺃﻭﻏﺎﺯﺍﺕﺃﻭﺃﻧﻮﺍﻉﻏﺒﺎﺭ

ﻗﺎﺑﻠﺔﻟﻼﺷﺘﻌﺎﻝ.ﺍﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺗﻮﻟﺪﺷﺮﺭﺍﻳﻤﻜﻦﺃﻥﻳﺆﺩﻱﻹﺷﻌﺎﻝﺍﻟﻐﺒﺎﺭﻭﺍﻷﺑﺨﺮﺓ.

◀

ﺍﺣﺮﺹﻋﻠﻰﺇﺑﻌﺎﺩﺍﻷﻃﻔﺎﻝﻭﺍﻷﺷﺨﺎﺹﺍﻵﺧﺮﻳﻦﺃﺛﻨﺎءﺍﺳﺘﺨﺪﺍﻡﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ.ﻓﻲﺣﺎﻟﺔﺍﻧﺼﺮﺍﻑ ﺍﻧﺘﺒﺎﻫﻚﻗﺪﺗﻔﻘﺪﺍﻟﺴﻴﻄﺮﺓﻋﻠﻰﺍﻟﺠﻬﺎﺯ.

ﺍﻟﺴﻼﻣﺔﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ

◀

ﻳﺠﺐﺃﻥﻳﻜﻮﻥﻗﺎﺑﺲﺗﻮﺻﻴﻞﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻣﺘﻼﺋﻤﺎﻣﻊﺍﻟﻤﻘﺒﺲ.ﻻﻳﺠﻮﺯﺗﻌﺪﻳﻞﺍﻟﻘﺎﺑﺲﺑﺄﻱﺣﺎﻝ

ﻣﻦﺍﻷﺣﻮﺍﻝ.ﻻﺗﺴﺘﺨﺪﻡﻗﻮﺍﺑﺲﻣﻬﺎﻳﺄﺓﻣﻊﺃﺩﻭﺍﺕﻛﻬﺮﺑﺎﺋﻴﺔﺫﺍﺕﻭﺻﻠﺔﺃﺭﺿﻲﻣﺤﻤﻴﺔ.ﺍﻟﻘﻮﺍﺑﺲﻏﻴﺮ ﺍﻟﻤﻌﺪﻟﺔﻭﺍﻟﻤﻘﺎﺑﺲﺍﻟﻤﻼﺋﻤﺔﺗﻘﻠﻞﻣﻦﺧﻄﺮﺣﺪﻭﺙﺻﺪﻣﺔﻛﻬﺮﺑﺎﺋﻴﺔ.

*2133068* 2133068 ﻋﺮﺑﻲ 13

◀

ﺗﺠﻨﺐﺣﺪﻭﺙﺗﻼﻣﺲﻟﻠﺠﺴﻢﻣﻊﺃﺳﻄﺢﻣﺆﺭﺿﺔﻣﺜﻞﺍﻷﺳﻄﺢﺍﻟﺨﺎﺻﺔﺑﺎﻟﻤﻮﺍﺳﻴﺮﻭﺃﺟﻬﺰﺓﺍﻟﺘﺪﻓﺌﺔ ﻭﺍﻟﻤﻮﺍﻗﺪﻭﺍﻟﺜﻼﺟﺎﺕ.ﻳﻨﺸﺄﺧﻄﺮﻣﺘﺰﺍﻳﺪﻣﻦﺣﺪﻭﺙﺻﺪﻣﺔﻛﻬﺮﺑﺎﺋﻴﺔﻋﻨﺪﻣﺎﻳﻜﻮﻥﺟﺴﻤﻚﻣﺘﺼﻼﺑﺎﻷﺭﺽ.

◀

ﺃﺑﻌﺪﺍﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻋﻦﺍﻷﻣﻄﺎﺭﺃﻭﺍﻟﺒﻠﻞ.ﺗﺴﺮﺏﺍﻟﻤﺎءﺇﻟﻰﺩﺍﺧﻞﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻳﺰﻳﺪﻣﻦﺧﻄﺮ ﺣﺪﻭﺙﺻﺪﻣﺔﻛﻬﺮﺑﺎﺋﻴﺔ.

◀

ﻻﺗﺴﺘﺨﺪﻡﺍﻟﻜﺎﺑﻞﻓﻲﺍﻟﻐﺮﺽﻏﻴﺮﺍﻟﻤﺨﺼﺺﻟﻪ،ﻛﺄﻥﺗﺴﺘﺨﺪﻣﻪﻟﺤﻤﻞﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺃﻭﺗﻌﻠﻴﻘﻬﺎﺃﻭ

ﻟﺴﺤﺐﺍﻟﻘﺎﺑﺲﻣﻦﺍﻟﻤﻘﺒﺲ.ﺍﺣﺘﻔﻆﺑﺎﻟﻜﺎﺑﻞﺑﻌﻴﺪﺍﻋﻦﺍﻟﺴﺨﻮﻧﺔﻭﺍﻟﺰﻳﺖﻭﺍﻟﺤﻮﺍﻑﺍﻟﺤﺎﺩﺓﻭﺍﻷﺟﺰﺍء ﺍﻟﻤﺘﺤﺮﻛﺔﻟﻠﺠﻬﺎﺯ.ﺍﻟﻜﺎﺑﻼﺕﺍﻟﺘﺎﻟﻔﺔﺃﻭﺍﻟﻤﺘﺸﺎﺑﻜﺔﺗﺰﻳﺪﻣﻦﺧﻄﺮﺣﺪﻭﺙﺻﺪﻣﺔﻛﻬﺮﺑﺎﺋﻴﺔ.

◀

ﻋﻨﺪﻣﺎﺗﻌﻤﻞﺑﺄﺩﺍﺓﻛﻬﺮﺑﺎﺋﻴﺔﻓﻲﻣﻜﺎﻥﻣﻜﺸﻮﻑ،ﻻﺗﺴﺘﺨﺪﻡﺳﻮﻯﻛﺎﺑﻼﺕﺍﻹﻃﺎﻟﺔﺍﻟﻤﻨﺎﺳﺒﺔﻟﻠﻌﻤﻞﻓﻲ ﺍﻟﻨﻄﺎﻕﺍﻟﺨﺎﺭﺟﻲ.ﺍﺳﺘﺨﺪﺍﻡﻛﺎﺑﻞﺇﻃﺎﻟﺔﻣﻨﺎﺳﺐﻟﻠﻌﻤﻞﻓﻲﺍﻟﻨﻄﺎﻕﺍﻟﺨﺎﺭﺟﻲﻳﻘﻠﻞﻣﻦﺧﻄﺮﺣﺪﻭﺙﺻﺪﻣﺔ ﻛﻬﺮﺑﺎﺋﻴﺔ.

◀

ﺇﺫﺍﺗﻌﺬﺭﺗﺠﻨﺐﺗﺸﻐﻴﻞﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻓﻲﻣﺤﻴﻂﺭﻃﺐ،ﻓﺎﺳﺘﺨﺪﻡﻣﻔﺘﺎﺡﺣﻤﺎﻳﺔﻣﻦﺗﺴﺮﺏﺍﻟﺘﻴﺎﺭ. ﺍﺳﺘﺨﺪﺍﻡﻣﻔﺘﺎﺡﺍﻟﺤﻤﺎﻳﺔﻣﻦﺗﺴﺮﺏﺍﻟﺘﻴﺎﺭﻳﻘﻠﻞﺧﻄﺮﺣﺪﻭﺙﺻﺪﻣﺔﻛﻬﺮﺑﺎﺋﻴﺔ.

ﺳﻼﻣﺔﺍﻷﺷﺨﺎﺹ

◀

ﻛﻦﻳﻘﻈﺎﻭﺍﻧﺘﺒﻪﻟﻤﺎﺗﻔﻌﻞﻭﺗﻌﺎﻣﻞﻣﻊﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺑﺘﻌﻘﻞﻋﻨﺪﺍﻟﻌﻤﻞﺑﻬﺎ.ﻻﺗﺴﺘﺨﺪﻡﺍﻷﺩﺍﺓ ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻋﻨﺪﻣﺎﺗﻜﻮﻥﻣﺘﻌﺒﺎﺃﻭﺗﺤﺖﺗﺄﺛﻴﺮﺍﻟﻤﺨﺪﺭﺍﺕﺃﻭﺍﻟﻜﺤﻮﻟﻴﺎﺕﺃﻭﺍﻟﻌﻘﺎﻗﻴﺮ.ﻓﻘﺪﻳﺘﺴﺒﺐﻋﺪﻡ

ﺍﻻﻧﺘﺒﺎﻩﻟﻠﺤﻈﺔﻭﺍﺣﺪﺓﺃﺛﻨﺎءﺍﻻﺳﺘﺨﺪﺍﻡﻓﻲﺣﺪﻭﺙﺇﺻﺎﺑﺎﺕﺑﺎﻟﻐﺔ.

◀ﺍﺭﺗﺪﺗﺠﻬﻴﺰﺍﺕﻭﻗﺎﻳﺔﺷﺨﺼﻴﺔﻭﺍﺭﺗﺪﺩﺍﺋﻤﺎﻧﻈﺎﺭﺓﻭﺍﻗﻴﺔ.ﺍﺭﺗﺪﺍءﺗﺠﻬﻴﺰﺍﺕﻭﻗﺎﻳﺔﺷﺨﺼﻴﺔ،ﻣﺜﻞﻗﻨﺎﻉﺍﻟﻮﻗﺎﻳﺔ

ﻣﻦﺍﻟﻐﺒﺎﺭﻭﺃﺣﺬﻳﺔﺍﻷﻣﺎﻥﺍﻟﻤﻀﺎﺩﺓﻟﻼﻧﺰﻻﻕﻭﺧﻮﺫﺓﺍﻟﻮﻗﺎﻳﺔﺃﻭﻭﺍﻗﻲﺍﻟﺴﻤﻊ،ﺗﺒﻌﺎﻟﻨﻮﻉﻭﺍﺳﺘﺨﺪﺍﻡﺍﻷﺩﺍﺓ ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ،ﻳﻘﻠﻞﻣﻦﺧﻄﺮﺍﻹﺻﺎﺑﺎﺕ.

◀

ﺗﺠﻨﺐﺍﻟﺘﺸﻐﻴﻞﺑﺸﻜﻞﻏﻴﺮﻣﻘﺼﻮﺩ.ﺗﺄﻛﺪﺃﻥﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻣﻄﻔﺄﺓﻗﺒﻞﺗﻮﺻﻴﻠﻬﺎﺑﺎﻟﻜﻬﺮﺑﺎءﻭ/ﺃﻭ ﺑﺎﻟﺒﻄﺎﺭﻳﺔﻭﻗﺒﻞﺭﻓﻌﻬﺎﺃﻭﺣﻤﻠﻬﺎ.ﺇﺫﺍﻛﺎﻥﺇﺻﺒﻌﻚﻋﻠﻰﺍﻟﻤﻔﺘﺎﺡﻋﻨﺪﺣﻤﻞﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺃﻭﻛﺎﻥﺍﻟﺠﻬﺎﺯ ﻓﻲﻭﺿﻊﺍﻟﺘﺸﻐﻴﻞﻋﻨﺪﺍﻟﺘﻮﺻﻴﻞﺑﺎﻟﻜﻬﺮﺑﺎء،ﻓﻘﺪﻳﺆﺩﻱﺫﻟﻚﻟﻮﻗﻮﻉﺣﻮﺍﺩﺙ.

◀

ﺃﺑﻌﺪﺃﺩﻭﺍﺕﺍﻟﻀﺒﻂﺃﻭﻣﻔﺎﺗﻴﺢﺭﺑﻂﺍﻟﺒﺮﺍﻏﻲﻗﺒﻞﺗﺸﻐﻴﻞﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ.ﺍﻷﺩﺍﺓﺃﻭﺍﻟﻤﻔﺘﺎﺡﺍﻟﻤﺘﻮﺍﺟﺪ

ﻓﻲﺟﺰءﺩﻭﺍﺭﻣﻦﺍﻟﺠﻬﺎﺯﻳﻤﻜﻦﺃﻥﻳﺆﺩﻱﻟﺤﺪﻭﺙﺇﺻﺎﺑﺎﺕ.

◀

ﺗﺠﻨﺐﺍﺗﺨﺎﺫﻭﺿﻊﻏﻴﺮﻃﺒﻴﻌﻲﻟﻠﺠﺴﻢ.ﺍﺣﺮﺹﻋﻠﻰﺃﻥﺗﻜﻮﻥﻭﺍﻗﻔﺎﺑﺄﻣﺎﻥﻭﺣﺎﻓﻆﻋﻠﻰﺗﻮﺍﺯﻧﻚﻓﻲﺟﻤﻴﻊ

ﺍﻷﻭﻗﺎﺕ.ﻣﻦﺧﻼﻝﺫﻟﻚﺗﺴﺘﻄﻴﻊﺍﻟﺴﻴﻄﺮﺓﻋﻠﻰﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺑﺸﻜﻞﺃﻓﻀﻞﻓﻲﺍﻟﻤﻮﺍﻗﻒﺍﻟﻤﻔﺎﺟﺌﺔ.

◀

ﺍﺭﺗﺪﻣﻼﺑﺲﻣﻨﺎﺳﺒﺔ.ﻻﺗﺮﺗﺪﻣﻼﺑﺲﻓﻀﻔﺎﺿﺔﺃﻭﺣﻠﻲ.ﺍﺣﺮﺹﻋﻠﻰﺃﻥﻳﻜﻮﻥﺍﻟﺸﻌﺮﻭﺍﻟﻤﻼﺑﺲ

ﻭﺍﻟﻘﻔﺎﺯﺍﺕﺑﻌﻴﺪﺓﻋﻦﺍﻷﺟﺰﺍءﺍﻟﻤﺘﺤﺮﻛﺔ.ﺍﻟﻤﻼﺑﺲﺍﻟﻔﻀﻔﺎﺿﺔﺃﻭﺍﻟﺤﻠﻲﺃﻭﺍﻟﺸﻌﺮﺍﻟﻄﻮﻳﻞﻳﻤﻜﻦﺃﻥﺗﺸﺘﺒﻚ

ﻓﻲﺍﻷﺟﺰﺍءﺍﻟﻤﺘﺤﺮﻛﺔ.

◀

ﺇﺫﺍﺃﻣﻜﻦﺗﺮﻛﻴﺐﺗﺠﻬﻴﺰﺍﺕﺷﻔﻂﻭﺗﺠﻤﻴﻊﺍﻟﻐﺒﺎﺭ،ﻓﺘﺄﻛﺪﺃﻧﻬﺎﻣﻮﺻﻠﺔﻭﻣﺴﺘﺨﺪﻣﺔﺑﺸﻜﻞﺳﻠﻴﻢ.ﺍﺳﺘﺨﺪﺍﻡ

ﺗﺠﻬﻴﺰﺓﺷﻔﻂﺍﻟﻐﺒﺎﺭﻳﻤﻜﻦﺃﻥﻳﻘﻠﻞﺍﻷﺧﻄﺎﺭﺍﻟﻨﺎﺗﺠﺔﻋﻦﺍﻟﻐﺒﺎﺭ.

ﺍﺳﺘﺨﺪﺍﻡﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻭﺍﻟﺘﻌﺎﻣﻞﻣﻌﻬﺎ

◀

ﻻﺗﻔﺮﻁﻓﻲﺍﻟﺘﺤﻤﻴﻞﻋﻠﻰﺍﻟﺠﻬﺎﺯ.ﺍﺳﺘﺨﺪﻡﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺍﻟﻤﻨﺎﺳﺒﺔﻟﻠﻌﻤﻞﺍﻟﺬﻱﺗﻘﻮﻡﺑﻪ.ﺍﺳﺘﺨﺪﺍﻡ

ﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺍﻟﻤﻨﺎﺳﺒﺔﻳﺘﻴﺢﻟﻚﺍﻟﻌﻤﻞﺑﺸﻜﻞﺃﻓﻀﻞﻭﺃﻛﺜﺮﺃﻣﺎﻧﺎﻓﻲﻧﻄﺎﻕﺍﻟﻌﻤﻞﺍﻟﻤﻘﺮﺭ.

◀

ﻻﺗﺴﺘﺨﺪﻡﺃﺩﺍﺓﻛﻬﺮﺑﺎﺋﻴﺔﺫﺍﺕﻣﻔﺘﺎﺡﺗﺎﻟﻒ.ﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺍﻟﺘﻲﻟﻢﻳﻌﺪﻳﻤﻜﻦﺗﺸﻐﻴﻠﻬﺎﺃﻭﺇﻃﻔﺎﺅﻫﺎﺗﻤﺜﻞ ﺧﻄﻮﺭﺓﻭﻳﺠﺐﺇﺻﻼﺣﻬﺎ.

◀

ﺍﺳﺤﺐﺍﻟﻘﺎﺑﺲﻣﻦﺍﻟﻤﻘﺒﺲﻭ/ﺃﻭﺍﺧﻠﻊﺍﻟﺒﻄﺎﺭﻳﺔﻣﻦﺍﻟﺠﻬﺎﺯﻗﺒﻞﺇﺟﺮﺍءﻋﻤﻠﻴﺎﺕﺿﺒﻂﺍﻟﺠﻬﺎﺯ،ﺃﻭﺍﺳﺘﺒﺪﺍﻝ

ﺃﺟﺰﺍءﺍﻟﻤﻠﺤﻘﺎﺕﺍﻟﺘﻜﻤﻴﻠﻴﺔﺃﻭﻋﻨﺪﺗﺮﻙﺍﻟﺠﻬﺎﺯ.ﻫﺬﺍﺍﻹﺟﺮﺍءﺍﻟﻮﻗﺎﺋﻲﻳﻤﻨﻊﺑﺪءﺗﺸﻐﻴﻞﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺩﻭﻥ ﻗﺼﺪ.

◀

ﺍﺣﺘﻔﻆﺑﺎﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻏﻴﺮﺍﻟﻤﺴﺘﺨﺪﻣﺔﺑﻌﻴﺪﺍﻋﻦﻣﺘﻨﺎﻭﻝﺍﻷﻃﻔﺎﻝ.ﻻﺗﺴﻤﺢﺑﺎﺳﺘﺨﺪﺍﻡﺍﻟﺠﻬﺎﺯﻣﻦ ﻗﺒﻞﺃﺷﺨﺎﺹﻟﻴﺴﻮﺍﻋﻠﻰﺩﺭﺍﻳﺔﺑﻪﺃﻭﻟﻢﻳﻘﺮﺃﻭﺍﻫﺬﻩﺍﻟﺘﻌﻠﻴﻤﺎﺕ.ﺍﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺧﻄﻴﺮﺓﻓﻲﺣﺎﻟﺔ

ﺍﺳﺘﺨﺪﺍﻣﻬﺎﻣﻦﻗﺒﻞﺃﺷﺨﺎﺹﻟﻴﺴﺖﻟﺪﻳﻬﻢﺍﻟﺨﺒﺮﺓﺍﻟﻮﺍﺟﺒﺔ.

◀

ﺍﺣﺮﺹﻋﻠﻰﺍﻟﻌﻨﺎﻳﺔﺍﻟﺘﺎﻣﺔﺑﺎﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ.ﺍﻓﺤﺺﺍﻷﺟﺰﺍءﺍﻟﻤﺘﺤﺮﻛﺔﻣﻦﺣﻴﺚﺃﺩﺍﺋﻬﺎﻟﻮﻇﻴﻔﺘﻬﺎﺑﺪﻭﻥ ﻣﺸﺎﻛﻞﻭﻋﺪﻡﺍﻧﺤﺼﺎﺭﻫﺎﻭﺍﻓﺤﺼﻬﺎﻣﻦﺣﻴﺚﻭﺟﻮﺩﺃﺟﺰﺍءﻣﻜﺴﻮﺭﺓﺃﻭﻣﺘﻌﺮﺿﺔﻟﻠﻀﺮﺭﻳﻤﻜﻦﺃﻥﺗﺆﺛﺮ ﺳﻠﺒﺎﻋﻠﻰﻭﻇﻴﻔﺔﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ.ﺍﻋﻤﻞﻋﻠﻰﺇﺻﻼﺡﺍﻷﺟﺰﺍءﺍﻟﺘﺎﻟﻔﺔﻗﺒﻞﺍﺳﺘﺨﺪﺍﻡﺍﻟﺠﻬﺎﺯ.ﺍﻟﻜﺜﻴﺮﻣﻦ

ﺍﻟﺤﻮﺍﺩﺙﻣﺼﺪﺭﻫﺎﺍﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺍﻟﺘﻲﺗﻢﺻﻴﺎﻧﺘﻬﺎﺑﺸﻜﻞﺭﺩﻱء.

◀

ﺣﺎﻓﻆﻋﻠﻰﺃﺩﻭﺍﺕﺍﻟﻘﻄﻊﺣﺎﺩﺓﻭﻧﻈﻴﻔﺔ.ﺗﺘﻤﻴﺰﺃﺩﻭﺍﺕﺍﻟﻘﻄﻊﺫﺍﺕﺣﻮﺍﻑﺍﻟﻘﻄﻊﺍﻟﺤﺎﺩﺓﺍﻟﻤﻌﺘﻨﻰﺑﻬﺎﺑﺪﻗﺔ

ﺑﺄﻧﻬﺎﺃﻗﻞﻋﺮﺿﺔﻟﻠﺘﻌﺜﺮﻭﺃﺳﻬﻞﻓﻲﺍﻟﺘﻌﺎﻣﻞ.

◀

ﺍﺳﺘﺨﺪﻡﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻭﺍﻟﻤﻠﺤﻘﺎﺕﺍﻟﺘﻜﻤﻴﻠﻴﺔﻭﺃﺩﻭﺍﺕﺍﻟﻌﻤﻞﻭﺧﻼﻓﻪﻃﺒﻘﺎﻟﻬﺬﻩﺍﻟﺘﻌﻠﻴﻤﺎﺕ.ﺍﺣﺮﺹ ﻓﻲﻫﺬﻩﺍﻷﺛﻨﺎءﻋﻠﻰﻣﺮﺍﻋﺎﺓﺍﺷﺘﺮﺍﻃﺎﺕﺍﻟﻌﻤﻞﻭﺍﻟﻤﻬﻤﺔﺍﻟﻤﺮﺍﺩﺗﻨﻔﻴﺬﻫﺎ.ﺍﺳﺘﺨﺪﺍﻡﺍﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ

ﻓﻲﺗﻄﺒﻴﻘﺎﺕﻏﻴﺮﺗﻠﻚﺍﻟﻤﻘﺮﺭﺓﻟﻬﺎﻳﻤﻜﻦﺃﻥﻳﺆﺩﻱﻟﻤﻮﺍﻗﻒﺧﻄﻴﺮﺓ.

14 ﻋﺮﺑﻲ 2133068 *2133068*

ﺍﻟﺨﺪﻣﺔ

◀

ﺍﻋﻤﻞﻋﻠﻰﺇﺻﻼﺡﺃﺩﺍﺗﻚﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻋﻠﻰﺃﻳﺪﻱﻓﻨﻴﻴﻦﻣﻌﺘﻤﺪﻳﻦﻓﻘﻂﻭﺍﻻﻗﺘﺼﺎﺭﻋﻠﻰﺍﺳﺘﺨﺪﺍﻡﻗﻄﻊ

ﺍﻟﻐﻴﺎﺭﺍﻷﺻﻠﻴﺔ.ﻭﺑﺬﻟﻚﺗﺘﺄﻛﺪﺃﻥﺳﻼﻣﺔﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺗﻈﻞﻗﺎﺋﻤﺔ.

2.2ﺇﺭﺷﺎﺩﺍﺕﺍﻟﺴﻼﻣﺔﺍﻟﺨﺎﺻﺔﺑﺎﻟﻤﻄﺎﺭﻕ

◀

ﺍﺳﺘﺨﺪﻡﻭﺍﻗﻴﺎﻟﻠﺴﻤﻊ.ﻟﺬﺍﻳﺮﺟﻰﻣﺮﺍﻋﺎﺓﺃﻥﺍﻟﻀﺠﻴﺞﺍﻟﺼﺎﺧﺐﻳﻤﻜﻦﺃﻥﻳُﻔﻘﺪﻙﺍﻟﻘﺪﺭﺓﻋﻠﻰﺍﻟﺴﻤﻊ.

◀

ﺍﺳﺘﺨﺪﻡﺍﻟﻤﻘﺎﺑﺾﺍﻹﺿﺎﻓﻴﺔﺍﻟﻤﻮﺭﺩﺓﻣﻊﺍﻟﺠﻬﺎﺯ.ﻓﻘﺪﺍﻥﺍﻟﺴﻴﻄﺮﺓﻳﻤﻜﻦﺃﻥﻳﺆﺩﻱﻟﻮﻗﻮﻉﺇﺻﺎﺑﺎﺕ.

◀

ﺃﻣﺴﻚﺍﻟﺠﻬﺎﺯﻣﻦﻣﻮﺍﺿﻊﺍﻟﻤﺴﻚﺍﻟﻤﻌﺰﻭﻟﺔﻋﻨﺪﺇﺟﺮﺍءﺃﻋﻤﺎﻝﻳﺤﺘﻤﻞﻓﻴﻬﺎﺃﻥﺗﺘﻼﻣﺲﺃﺩﺍﺓﺍﻟﺸﻐﻞﻣﻊ

ﺃﺳﻼﻙﻛﻬﺮﺑﺎﺋﻴﺔﻣﺨﻔﻴﺔﺃﻭﻣﻊﺳﻠﻚﺍﻟﻜﻬﺮﺑﺎءﻟﻠﺠﻬﺎﺯﺫﺍﺗﻪ.ﺣﻴﺚﺃﻥﻣﻼﻣﺴﺔﺳﻠﻚﻳﺴﺮﻱﻓﻴﻪﺍﻟﺘﻴﺎﺭﺍﻟﻜﻬﺮﺑﺎﺋﻲ

ﻳﻤﻜﻦﺃﻥﻳﻨﻘﻞﺍﻟﺠﻬﺪﺍﻟﻜﻬﺮﺑﺎﺋﻲﻟﻸﺟﺰﺍءﺍﻟﻤﻌﺪﻧﻴﺔﺑﺎﻟﺠﻬﺎﺯﻭﻳﺆﺩﻱﻟﺤﺪﻭﺙﺻﺪﻣﺔﻛﻬﺮﺑﺎﺋﻴﺔ.

2.3ﺇﺭﺷﺎﺩﺍﺕﺇﺿﺎﻓﻴﺔﻟﻠﺴﻼﻣﺔ

ﺳﻼﻣﺔﺍﻷﺷﺨﺎﺹ

◀ﺍﻗﺘﺼﺮﻋﻠﻰﺍﺳﺘﺨﺪﺍﻡﺍﻟﻤﻨﺘﺞﻭﻫﻮﻓﻲﺣﺎﻟﺔﺳﻠﻴﻤﺔﻣﻦﺍﻟﻨﺎﺣﻴﺔﺍﻟﻔﻨﻴﺔ.

◀

ﻻﺗﻘﻢﺃﺑﺪﺍﺑﺄﻳﺔﺗﺪﺧﻼﺕﺃﻭﺗﻐﻴﻴﺮﺍﺕﻋﻠﻰﺍﻟﺠﻬﺎﺯ.

◀

ﺃﺛﻨﺎءﺃﻋﻤﺎﻝﺍﻟﺜﻘﺐﻗﻢﺑﺘﺄﻣﻴﻦﺍﻟﻨﻄﺎﻕﺍﻟﻮﺍﻗﻊﻋﻠﻰﺍﻟﺠﻬﺔﺍﻟﻤﻘﺎﺑﻠﺔﻟﻠﻌﻤﻞ.ﺍﻟﺸﻈﺎﻳﺎﺍﻟﻤﺘﻨﺎﺛﺮﺓﻳﻤﻜﻦﺃﻥﺗﺘﻄﺎﻳﺮ

ﻭ/ﺃﻭﺗﺴﻘﻂﻭﺗﺼﻴﺐﺍﻵﺧﺮﻳﻦ.

◀

ﺃﻣﺴﻚﺍﻟﺠﻬﺎﺯﺩﺍﺋﻤﺎﺑﻴﺪﻳﻚﻣﻦﺍﻟﻤﻘﺎﺑﺾﺍﻟﻤﻌﻨﻴﺔ.ﺣﺎﻓﻆﻋﻠﻰﺟﻔﺎﻑﻭﻧﻈﺎﻓﺔﺍﻟﻤﻘﺎﺑﺾ.

◀

ﺃﻣﺴﻚﺍﻟﻤﻘﺒﺾﺍﻟﺠﺎﻧﺒﻲﺩﺍﺋﻤﺎﻣﻦﺍﻟﺨﺎﺭﺝ.ﻋﻨﺪﺍﻟﺜﻘﺐﻭﺍﻟﺮﺑﻂﻳﻤﻜﻦﺃﻥﻳﻨﺤﺮﻑﺍﻟﺠﻬﺎﺯﺟﺎﻧﺒﺎ.

◀

ﺗﺠﻨﺐﻣﻼﻣﺴﺔﺍﻷﺟﺰﺍءﺍﻟﺪﻭﺍﺭﺓ-ﺧﻄﺮﺍﻹﺻﺎﺑﺔ!

◀

ﺍﺣﺮﺹﺃﺛﻨﺎءﺍﺳﺘﺨﺪﺍﻡﺍﻟﺠﻬﺎﺯﻋﻠﻰﺍﺳﺘﻌﻤﺎﻝﻧﻈﺎﺭﺓﻭﺍﻗﻴﺔﻣﻼﺋﻤﺔﻭﺧﻮﺫﺓﺣﻤﺎﻳﺔﻭﻭﺍﻗﻲﻟﻠﺴﻤﻊﻭﻗﻔﺎﺯﻭﺍﻗﻲ ﻭﻛﻤﺎﻣﺔﺧﻔﻴﻔﺔﻟﻠﺘﻨﻔﺲ.

◀

ﺍﺭﺗﺪﻗﻔﺎﺯﺍﻭﺍﻗﻴﺎﺃﺛﻨﺎءﺗﻐﻴﻴﺮﺍﻷﺩﻭﺍﺕ.ﻣﻼﻣﺴﺔﺃﺩﺍﺓﺍﻟﺸﻐﻞﻗﺪﺗﺆﺩﻱﻟﻮﻗﻮﻉﺇﺻﺎﺑﺎﺕﺑﺠﺮﻭﺡﻗﻄﻌﻴﺔﻭﺇﺻﺎﺑﺔ ﺑﺤﺮﻭﻕ.

◀

ﺍﺳﺘﺨﺪﻡﻭﺍﻗﻴﺎًﻟﻠﻌﻴﻨﻴﻦ.ﺍﻟﺸﻈﺎﻳﺎﺍﻟﻤﺘﻄﺎﻳﺮﺓﻳﻤﻜﻦﺃﻥﺗﺼﻴﺐﺍﻟﺠﺴﻢﻭﺍﻟﻌﻴﻨﻴﻦ.

◀

ﺍﺣﺮﺹﻗﺒﻞﺑﺪءﺍﻟﻌﻤﻞﻋﻠﻰﻣﻌﺮﻓﺔﻓﺌﺔﺧﻄﺮﺍﻟﻐﺒﺎﺭﺍﻟﻨﺎﺷﺊﻋﻨﺪﺇﺟﺮﺍءﺍﻟﻌﻤﻞ.ﺍﺳﺘﺨﺪﻡﺷﻔﺎﻁﻏﺒﺎﺭﺃﻋﻤﺎﻝ ﺍﻹﻧﺸﺎءﺍﺕﺫﻱﻓﺌﺔﺣﻤﺎﻳﺔﻣﺼﺮﺡﺑﻬﺎﺭﺳﻤﻴﺎﻭﻣﻄﺎﺑﻖﻟﻠﺘﻌﻠﻴﻤﺎﺕﺍﻟﻤﺤﻠﻴﺔﺍﻟﺨﺎﺻﺔﺑﺎﻟﺤﻤﺎﻳﺔﻣﻦﺍﻟﻐﺒﺎﺭ.

◀

ﺍﺳﺘﺨﺪﻡﺷﻔﺎﻁﺍﻟﻐﺒﺎﺭﻭﻣﺰﻳﻞﺍﻟﻐﺒﺎﺭﺍﻟﻤﺤﻤﻮﻝﺍﻟﻤﻨﺎﺳﺐﺇﻥﺃﻣﻜﻦ.ﺍﻟﻐﺒﺎﺭﺍﻟﻨﺎﺗﺞﻋﻦﺧﺎﻣﺎﺕﻣﺜﻞﺍﻟﻄﻼءﺍﻟﻤﺤﺘﻮﻱ

ﻋﻠﻰﺍﻟﺮﺻﺎﺹﻭﺑﻌﺾﺃﻧﻮﺍﻉﺍﻷﺧﺸﺎﺏﻭﺍﻟﺨﺮﺳﺎﻧﺔ/ﺍﻟﺠﺪﺭﺍﻥﻭﺍﻟﺼﺨﻮﺭﺍﻟﻤﺤﺘﻮﻳﺔﻋﻠﻰﺍﻟﻜﻮﺍﺭﺗﺰﻭﺍﻟﻤﻌﺎﺩﻥ ﺍﻟﺼﺨﺮﻳﺔﻭﺍﻟﻤﻌﺎﺩﻥﻫﻮﻏﺒﺎﺭﺿﺎﺭﺑﺎﻟﺼﺤﺔ.

◀ﺍﺣﺮﺹﻋﻠﻰﻭﺟﻮﺩﺗﻬﻮﻳﺔﺟﻴﺪﺓﻟﻤﻜﺎﻥﺍﻟﻌﻤﻞﻭﺍﺭﺗﺪﻋﻨﺪﺍﻟﻠﺰﻭﻡﻗﻨﺎﻉﺗﻨﻔﺲﻣﺨﺼﺺﻟﻨﻮﻋﻴﺔﺍﻟﻐﺒﺎﺭﺍﻟﻤﻨﺒﻌﺚ.

ﻣﻼﻣﺴﺘﻪﺃﻭﺍﺳﺘﻨﺸﺎﻗﻪﻗﺪﻳﺴﺒﺐﺃﻋﺮﺍﺽﺣﺴﺎﺳﻴﺔﻭ/ﺃﻭﺃﻣﺮﺍﺽﺍﻟﺠﻬﺎﺯﺍﻟﺘﻨﻔﺴﻲﻟﻠﻤﺴﺘﺨﺪﻡﺃﻭﻟﻸﺷﺨﺎﺹ

ﺍﻟﻤﺘﻮﺍﺟﺪﻳﻦﻋﻠﻰﻣﻘﺮﺑﺔﻣﻨﻪ.ﻫﻨﺎﻙﺃﻧﻮﺍﻉﻣﻌﻴﻨﺔﻣﺴﺮﻃﻨﺔﻣﻦﺍﻟﻐﺒﺎﺭﻣﺜﻞﻏﺒﺎﺭﺧﺸﺐﺍﻟﺒﻠﻮﻁﺃﻭﻏﺒﺎﺭﺧﺸﺐ

ﺍﻟﺰﺍﻥ،ﻭﻻﺳﻴﻤﺎﺇﺫﺍﺍﺭﺗﺒﻄﺖﻫﺬﻩﺍﻷﻧﻮﺍﻉﺑﻤﻮﺍﺩﺇﺿﺎﻓﻴﺔﻟﻤﻌﺎﻟﺠﺔﺍﻷﺧﺸﺎﺏ)ﻣﺜﻞﺍﻟﻜﺮﻭﻡﻭﻣﻮﺍﺩﺣﻤﺎﻳﺔ

ﺍﻷﺧﺸﺎﺏ(.ﻻﻳﺠﻮﺯﺍﻟﺘﻌﺎﻣﻞﻣﻊﺍﻟﻤﻮﺍﺩﺍﻟﻤﺤﺘﻮﻳﺔﻋﻠﻰﺍﻷﺳﺒﺴﺘﻮﺱﺇﻻﻣﻦﻗﺒﻞﻓﻨﻴﻴﻦﻣﺘﺨﺼﺼﻴﻦ.

◀

ﺧﺬﻗﺴﻄﺎًﻣﻦﺍﻟﺮﺍﺣﺔﺃﺛﻨﺎءﺍﻟﻌﻤﻞﻭﻗﻢﺑﺘﻤﺎﺭﻳﻦﺍﺳﺘﺮﺧﺎءﻟﺴﺮﻳﺎﻥﺍﻟﺪﻡﻓﻲﺍﻷﺻﺎﺑﻊﺑﺸﻜﻞﺃﻓﻀﻞ.ﻋﻨﺪﺍﻟﻘﻴﺎﻡ

ﺑﺄﻋﻤﺎﻝﻟﻔﺘﺮﺍﺕﻃﻮﻳﻠﺔﻓﻘﺪﻳﺤﺪﺙﺍﺿﻄﺮﺍﺑﺎﺕﻓﻲﺍﻷﻭﻋﻴﺔﺍﻟﺪﻣﻮﻳﺔﺃﻭﺍﻟﺠﻬﺎﺯﺍﻟﻌﺼﺒﻲﺑﺴﺒﺐﻛﺜﺮﺓﺍﻻﻫﺘﺰﺍﺯﺍﺕ

ﻋﻠﻰﺍﻷﺻﺎﺑﻊ،ﺍﻷﻳﺪﻱﺃﻭﻣﻌﺼﻢﺍﻟﻴﺪ.

ﺍﻟﺴﻼﻣﺔﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ

◀

ﻗﺒﻞﺑﺪءﺍﻷﻋﻤﺎﻝﺍﻓﺤﺺﻧﻄﺎﻕﺍﻟﻌﻤﻞﻣﻦﺣﻴﺚﻭﺟﻮﺩﺗﻮﺻﻴﻼﺕﻛﻬﺮﺑﺎءﻣﻐﻄﺎﺓﺃﻭﻣﻮﺍﺳﻴﺮﻟﻠﻐﺎﺯﻭﺍﻟﻤﺎء.ﺍﻷﺟﺰﺍء ﺍﻟﻤﻌﺪﻧﻴﺔﺍﻟﺨﺎﺭﺟﻴﺔﺑﺎﻟﺠﻬﺎﺯﻳﻤﻜﻦﺃﻥﺗﺘﺴﺒﺐﻓﻲﺻﺪﻣﺔﻛﻬﺮﺑﺎﺋﻴﺔ،ﺇﺫﺍﻗﻤﺖﺩﻭﻥﻗﺼﺪﺑﺈﺗﻼﻑﺇﺣﺪﻯﺗﻮﺻﻴﻼﺕ ﺍﻟﺘﻴﺎﺭ.

ﺍﻻﺳﺘﺨﺪﺍﻡﻭﺍﻟﺘﻌﺎﻣﻞﺑﻌﻨﺎﻳﺔﻣﻊﺍﻷﺩﻭﺍﺕﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ

◀

ﻗﻢﺑﺈﻳﻘﺎﻑﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﻋﻠﻰﺍﻟﻔﻮﺭ،ﺑﻤﺠﺮﺩﺗﻌﺮﺽﺍﻷﺩﺍﺓﻟﻺﻋﺎﻗﺔ.ﻳﻤﻜﻦﺃﻥﻳﻨﺤﺮﻑﺍﻟﺠﻬﺎﺯﺟﺎﻧﺒﺎ.

◀

ﻗﺒﻞﺍﻟﺘﺨﺰﻳﻦﺍﻧﺘﻈﺮﺇﻟﻰﺃﻥﺗﺘﻮﻗﻒﺍﻷﺩﺍﺓﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔﺗﻤﺎﻣﺎ.

ページを読み込んでいます...

Hilti TE 50-AVR ユーザーマニュアル

関連論文