Bose SoundSport® in-ear headphones — Apple devices 取扱説明書

Solo 15/10

TV sound system

| | | |

Owner’s Guide |

Safety Information

2 - English

Please read this guide

Please read this owner’s guide carefully and save it for future reference.

The lightning ash with arrowhead symbol within an equilateral triangle alerts the user to the presence of

uninsulated, dangerous voltage within the system enclosure that may be of sufcient magnitude to

constitute a risk of electric shock.

The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the user

to the presence of important operating and maintenance instructions in this owner’s guide.

WARNINGS:

• To reduce the risk of re or electrical shock, do not expose the product to rain or moisture.

• Do not expose this apparatus to dripping or splashing, and do not place objects lled with liquids, such

as vases, on or near the apparatus. As with any electronic products, use care not to spill liquids into any

part of the system. Liquids can cause a failure and/or a re hazard.

• Solo 10 remote:

Warning: Do not ingest battery, chemical burn hazard.

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell

battery is swallowed it can cause severe internal burns in just two hours and can lead to death. Keep

new and used batteries away from children. If the battery compartment does not close securely, stop

using the product and keep it away from children. If you think the battery may have been swallowed

or placed inside any part of the body, seek immediate medical attention. The coin/button cell battery

may explode or cause a re or chemical burn if incorrectly replaced or mishandled. Do not recharge,

disassemble, heat above 212°F (100°C) or incinerate. Replace only with an agency approved (ex. UL)

CR2032 or DL2032 3-volt lithium battery. Dispose of used batteries promptly.

• Solo 15 remote: Do not dismantle, open or shred battery pack or cells. Do not expose batteries or

a battery pack to heat or re. Avoid storage in direct sunlight. Do not short-circuit battery. Do not store

batteries carelessly in a box or drawer where they may short-circuit each other or be short-circuited by

other metal objects. Do not remove a battery from its original packaging until required for use. Do not

subject batteries to mechanical shock. In the event of a battery leaking, do not allow the liquid to come

in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts

of water and seek medical advice. Observe the plus (+) and minus (-) marks on the battery and equip-

ment and ensure correct use. Do not use any battery pack or cell which is not designed for use with the

product. Keep batteries out of the reach of children. Seek medical advice immediately if a battery has

been swallowed. Always purchase the correct battery for the equipment. Keep batteries clean and dry.

Wipe the battery terminals with a clean dry cloth if they become dirty. Use the battery only in the applica-

tion for which it was intended. When possible, remove the battery from the equipment when not in use.

Replace only with AA (IEC LR06) alkaline batteries.

• Do not place any naked ame sources, such as lighted candles, on or near the apparatus.

• Never place the equipment in an unstable location. The equipment may fall, causing serious personal

injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions

such as:

- Using cabinets or stands recommended by the manufacturer of the equipment.

- Only using furniture that can safely support the equipment.

- Ensuring the equipment is not overhanging the edge of the supporting furniture.

- Not placing the equipment on tall furniture (for example, cupboards or bookcases) without anchoring

both the furniture and the equipment to a suitable support.

- Not standing the equipment on cloth or other materials placed between the equipment and supporting

furniture.

- Educating children about the dangers of climbing on furniture to reach the equipment or its controls.

• If you doubt your ability to safely mount your television or set up this product, contact a professional

installer for help.

• Do not allow children to push, pull, or climb on an A/V monitor. This may cause it to tip over, possibly

resulting in personal injury or death. For added safety and stability, be sure to secure the monitor using

a suitable anti-tip device.

Safety Information

English - 3

WARNING: This product contains magnetic material. Please contact your physician if you have any

questions on whether this might affect the operation of your implantable medical device.

WARNING: Contains small parts which may be a choking hazard. Not suitable for children under age 3.

CAUTION: Do not make unauthorized alterations to the product; doing so may compromise safety,

regulatory compliance, system performance, and may void the warranty.

Notes:

• Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall

remain readily operable.

• This product must be used indoors. It is neither designed nor tested for use outdoors, in recreation vehicles, or

on boats.

• The product label is located on the bottom or the back of the product.

Please dispose of used batteries properly, following any local regulations.

Do not incinerate.

This product conforms to all applicable EU Directive requirements. The complete Declaration of

Conformity can be found at www.Bose.com/compliance.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

ampliers) that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

10. Only use attachments/accessories specied by the manufacturer.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all servicing to qualied personnel. Servicing is required when the apparatus has been damaged in

a way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

This symbol means the product must not be discarded as household waste, and should be delivered to

an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural

resources, human health and the environment. For more information on disposal and recycling of this

product, contact your local municipality, disposal service, or the shop where you bought this product.

4 - English

Safety Information

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, you are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modications not expressly approved by Bose Corporation could void the user’s authority to operate

this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

CAN ICES-3 (B) / NMB-3 (B)

Names and Contents of Toxic or Hazardous Substances or Elements

Toxic or Hazardous Substances and Elements

Part Name

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent

(CR(VI))

Polybrominated

Biphenyl (PBB)

Polybrominated

diphenylether (PBDE)

PCBs X O O O O O

Metal parts X O O O O O

Plastic parts O O O O O O

Speakers X O O O O O

Cables X O O O O O

O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement in SJ/T 11363-2006.

X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is

above the limit requirement in SJ/T 11363-2006.

Please complete and retain for your records

The serial and model number can be found on the bottom panel.

Serial number: _________________________________________________________________

Model number: _________________________________________________________________

Purchase date: _________________________________________________________________

We suggest you keep your receipt with this owner’s guide.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are

registered trademarks of Dolby Laboratories.

Blu-ray Disc

™

is a trademark owned by Blu-ray Disc Association (BDA).

©201 Bose Corporation. No part of this work may be reproduced, modied, distributed, or otherwise used without

prior written permission.

8

Contents

English - 5

Introduction

ank you… ........................................................................................................... 7

Unpacking ............................................................................................................. 7

System Setup

Step 1: Placing the system ................................................................................. 8

Step 2: Choosing the type of audio cable to use ............................................ 9

Step 3: Connecting the selected audio cable to your TV ............................. 10

Step 4: Connecting the audio cable to the Solo system .............................. 11

Important instructions for optical cable connections .......................... 12

Step 5: Connecting the Solo system to power ............................................... 13

Step 6: Placing your TV on the Solo system ................................................... 14

Step 7: Turning off your TV speakers ............................................................... 15

Step 8: Checking for sound ................................................................................ 16

Step 9: Adjusting the bass ................................................................................. 16

Using alternate connections ............................................................................. 17

Connecting a cable/satellite box to the system .................................... 17

Connecting a TV headphones output to the system ............................ 18

Connecting multiple devices to the system ................................................... 19

Operation

Getting system information .............................................................................. 20

Controlling the volume ...................................................................................... 21

Using auto-wake .................................................................................................. 21

Using the Solo 15 universal remote .................................................................. 22

Programming the Solo 15 universal remote .................................................. 23

Locate the code ............................................................................................ 23

Enter the code .............................................................................................. 23

Test the code ................................................................................................. 23

Customizing the power button ................................................................. 24

Resyncing your cable/satellite box and TV ............................................. 24

Switching between sources ....................................................................... 24

Controlling the volume ............................................................................... 25

6 - English

Contents

Function buttons ......................................................................................... 25

Using dialog mode ....................................................................................... 25

Using the Solo 10 remote ................................................................................... 26

Optional Solo 15 system universal remote control ................................ 26

Using a non-Bose remote control ............................................................. 26

Using dialog mode ....................................................................................... 26

Troubleshooting .................................................................................................. 27

Care and Maintenance

Replacing the remote batteries ........................................................................ 29

Solo 15 universal remote ............................................................................. 29

Solo 10 remote .............................................................................................. 29

Cleaning ................................................................................................................. 30

Customer service ................................................................................................. 30

Limited warranty ................................................................................................. 30

Technical information ......................................................................................... 30

English - 7

Introduction

ank you…

Thank you for choosing the Bose

®

Solo 15/10 TV sound system for your home.

This stylish, unobtrusive speaker system is designed to ﬁt under most 46" TVs and

many 50" TVs. It delivers superb acoustic performance that will greatly enhance

your TV viewing experience.

Unpacking

Carefully unpack the carton and conﬁrm that you have all the parts shown here:

OR

Solo 15/10 TV sound system Solo 10 remote

Power cord

(The appropriate

power cord for your

region is included)

Optical digital

audio cable

Analog stereo

audio cable

Solo 15

universal remote

Coaxial digital

audio cable

(Included in

Europe only)

If any part of the product appears to be damaged, do not attempt to use it.

Contact your authorized Bose dealer immediately or call Bose Customer Service.

Refer to the contact list enclosed in the carton for contact information.

Be sure to save the carton and packing materials. They provide the safest means

for transporting or storing the product.

8 - English

System Setup

Step 1: Placing the system

1. Move your TV aside and turn it so you can see the Audio Out panel.

2. Place the Solo system where you had your TV.

Placement guidelines:

• The Bose

®

Solo 15/10 system is designed to ﬁt under TVs that weigh no more than

75 lbs (34 kg) and have bases no wider than 24" (61 cm), and no deeper than 12.25"

(31 cm).

• The base of your TV should be centered on the top of the system and must not

hang over any of its edges.

• If the TV base is too large to ﬁt on top of the system, place the sound system in

another location such as on an open shelf under the TV, but keep it close to your

TV so the audio cable will reach. You can also mount your TV on the wall above

the system.

• If placing the sound system in a cabinet or on a shelf, position the front of the

system as close as possible to the front edge of the shelf for optimum audio

performance.

Cautions:

• DO NOT place a CRT type TV on this system. It is not designed for use with this

type of TV.

• Allowing the base of your TV to hang over any edge of this speaker system in-

creases the risk of the TV tipping, which may result in injury.

• If placing the sound system backed up to a wall, make sure there is a space of at

least 1" (2.5 cm) between the wall and the rear of the system.

• With any placement of this product, make sure the ventilation openings on the rear

panel are not blocked.

• If your TV comes with an anti-tip device, install it according to the manufacturer’s

instructions and adjust the tether as instructed after placing the TV on top of the

system. Installing an anti-tip device is recommended when using a TV with this

product. If your TV did not come with an anti-tip device, you can get one from

most retail TV suppliers.

TV Audio OUT panel

System Setup

English - 9

Step 2: Choosing the type of audio cable

to use

1. On the back of your TV, locate the Audio Out connector panel and note which

type of audio output connectors your TV has.

Use either of these connections for best

audio performance.

Optical digital

audio

Coaxial digital

audio

Analog stereo

audio

Use this connection

if no optical or

coaxial digital audio

outputs are available.

2. Choose the appropriate audio cable for your TV.

Note: Your Solo system may come with several types of audio cables. Only one

audio connection is needed. Choose one cable and set the others aside.

Note: The optical or coaxial cable will provide the best audio performance.

Use the analog cable only if your TV does not have an optical output or a

coaxial output.

Tip: If your TV does not have any audio outputs, you can use the audio outputs

on another device. See “Using alternate connections” on page 17 for other

ways to connect the Solo TV sound system.

System Setup

10 - English

Step 3: Connecting the selected audio cable

to your TV

1. On the back of your TV, locate the Audio OUT connector panel.

2. Plug one end of the selected audio cable into the correct Audio OUT

connector.

Caution: If using the optical cable, make sure you remove the protective cap and

hold the plug in the correct orientation for the Audio OUT connector on

your TV.

System Setup

English - 11

Step 4: Connecting the audio cable to the Solo

system

Plug the other end of the selected audio cable into the corresponding connector on

the Solo system.

Note: If using the optical cable, please read the Important Instructions on

page 12.

Audio IN Solo system

Remove caps

Audio OUT

TV

Note: Only one audio connection is needed.

System Setup

12 - English

Important instructions for optical cable connections

1. Remove the protective cap from both ends of the optical cable.

Bose logo

Remove caps

2. Hold the optical cable plug with the Bose logo facing up, as shown.

3. Align the plug with the Optical connector on the Solo system and insert the plug

carefully.

Note: The Optical connector on the Solo system has a hinged door that swings out

of the way when you insert the plug.

Hinged door

Caution: Inserting the plug in the wrong orientation can damage the plug and/or

the connector.

4. Firmly push the plug into the connector until you hear or feel a click.

Test to be sure the plug cannot easily slip out of the connector.

System Setup

English - 13

Step 5: Connecting the Solo system to power

1. Plug one end of the power cord into the Power connector.

2. Plug the other end into a live AC power (mains) outlet.

A few moments after applying power, the system emits two tones indicating that

it is ready to use.

Power connector

Tip: Bose recommends using a safety agency-approved surge protector on all

electronic equipment. Voltage variations and spikes can damage electronic

components in any system.

System Setup

14 - English

Step 6: Placing your TV on the Solo system

Place your TV on the Solo system, making sure the TV stand is centered on the

top of the system. Refer to “Placement guidelines:” on page 8.

Caution: Be sure to center the base of your TV on the top of this product.

Cautions:

• DO NOT place a CRT type TV on this system. It is not designed for use with

this type of TV.

• Allowing the base of your TV to hang over any edge of this speaker system

increases the risk of the TV tipping, which may result in injury.

• If placing the sound system backed up to a wall, make sure there is a space of at

least 1" (2.5 cm) between the wall and the rear of the system.

• If your TV comes with an anti-tip device, install it according to the manufacturer’s

instructions and adjust the tether as instructed after placing the TV on top of the

system. Installing an anti-tip device is recommended when using a TV with this

product. If your TV did not come with an anti-tip device, you can get one from

most retail TV suppliers.

System Setup

English - 15

Step 7: Turning off your TV speakers

To enjoy the full beneﬁt of hearing TV audio through the Solo TV sound system, the

internal speakers in your TV should be turned off.

Note: Check your TV owner’s guide for help using the TV menus.

1. Turn on your TV.

2. Go to the TV menu and select Audio, Sound, or Speaker Settings.

3. Look for the menu item that allows you to turn off the TV speakers. This menu

item may be called Speakers On/Off or something closely related.

4. If there is no setting for turning the TV speakers off, adjust the TV volume to its

lowest setting.

To conﬁrm your TV speakers are turned off:

1. Press

(mute) on the Solo remote.

2. Check that no sound is coming from your TV.

Tip: If you connected your TV to the Solo system using an optical digital cable,

you may need to make sure that your TV’s audio settings do not inhibit the

audio output signal.

• Look for a menu item in your TV’s Audio Settings that may affect digital

audio output. You may have to select the digital output you want to use.

• Look for any setting that selects the type of audio output, such as Stereo or

5.1 Channel Audio output. You may need to select such a setting in order to

enable the audio output.

System Setup

16 - English

Step 8: Checking for sound

1. Power on your TV and cable/satellite box (if needed).

2. Press

on the Solo system remote.

Make sure the system status indicator is solid green.

System status

indicator

3. Check if sound is coming from the Solo system.

If you do not hear sound from the Solo system see “Troubleshooting” on page

27.

Tip: At this time, you may consider setting your Solo system to automatically wake

from standby whenever it receives a sound signal. See “Using auto-wake” on

page 21.

Step 9: Adjusting the bass

The bass control knob on the back of the system allows you to change the

bass level output of the system.

Turn the bass control knob right to increase the bass, left to decrease the bass.

Note: For optimal sound quality for dialog-only programming, such as news and talk

shows, see “Using dialog mode” on page 25 (Solo 15) or page 26 (Solo 10).

System Setup

English - 17

Using alternate connections

You may need to use an alternate connection:

• If your TV does not have any audio output connections or does not deliver the

audio to the Solo 15/10 system. See “Connecting a cable/satellite box to the sys-

tem” or “Connecting a TV headphones output to the system” on pages 17-18.

• If you do not get sound from a DVD player that is connected to your TV.

See “Connecting multiple devices to the system” on page 19.

Connecting a cable/satellite box to the system

You can connect a cable/satellite box to the Solo 15/10 system. Only one cable is

needed.

Caution: If using an optical cable, refer to page 12 for important instructions.

1. On the back of your cable/satellite box, locate the Audio Out connector panel

and note which type of audio outputs your cable/satellite box has.

Audio OUT

Cable/satellite

box

Audio IN Solo 15/10 system

Remove caps

2. Choose the appropriate audio cable for your cable/satellite box.

3. Connect the audio cable from your cable/satellite box’s Audio Out connector

panel to the Solo system.

System Setup

18 - English

Connecting a TV headphones output to the system

If your TV only has a headphones connector, you need a dual RCA-to-3.5 mm stereo

cable (not provided) to connect to the Solo 15/10 system.

1. Insert the stereo plug into the TV headphones connector.

2. Insert the white plug into the L connector on the Solo system.

3. Insert the red plug into the R connector on the Solo system.

4. Ensure your TV speakers are on. Refer to your TV’s Owner’s Guide for more

information.

5. To ensure optimal volume control from your system, set your TV’s volume to

75 percent of maximum; then set the volume level of your system using the

remote control.

Audio IN Solo 15/10 system

Audio OUT

TV headphones

or other variable

audio output

Dual RCA-to-3.5 mm

stereo cable

(not provided)

System Setup

English - 19

Connecting multiple devices to the system

If you have a device such as a DVD player connected to your TV, you may discover

that your TV does not pass audio from the DVD player to the audio output on your

TV. The Solo system provides a solution to this problem. You can connect up to

three devices to the Solo system using a different type of audio cable for each.

For example, the ﬁgure below shows a cable/satellite box and a DVD player or game

system connected to the Solo system.

Note: This alternate connection scheme may not work with the equipment you have

in your home because some devices like cable/satellite boxes always remain

on. When multiple devices are connected to the Solo system, turn on only the

device you want to use and turn off the others.

Caution: If using an optical cable, refer to page 12 for important instructions.

Audio OUT

Cable/satellite box

Audio OUT

DVD player or game system

Audio IN Solo 15/10 system

20 - English

Operation

Getting system information

The system status indicator tells you when the system is on and provides you with a

system status during operation.

System status

indicator

System status:

Indicator activity System state

Off System off (standby)

Dim amber Standby, auto wake is enabled

Solid green Power is on

Blinking green

or

Blinking amber

(if dialog mode is enabled)

System is muted

Fast blinking green

or

Fast blinking amber

(if dialog mode is enabled)

Volume is being adjusted

Solid amber Dialog mode is enabled

Solid red System error - call Bose Customer Service

ページが読み込まれています...

Bose SoundSport® in-ear headphones — Apple devices 取扱説明書

Bose SoundSport® in-ear headphones — Apple devices 取扱説明書

関連論文

その他のドキュメント